AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
01f94c4a6c
kernel_optimize_test/arch/sparc64/kernel/trampoline.S

451 lines
10 KiB
ArmAsm
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
/* $Id: trampoline.S,v 1.26 2002/02/09 19:49:30 davem Exp $
* trampoline.S: Jump start slave processors on sparc64.
*
* Copyright (C) 1997 David S. Miller (davem@caip.rutgers.edu)
*/
#include <asm/head.h>
#include <asm/asi.h>
#include <asm/lsu.h>
#include <asm/dcr.h>
#include <asm/dcu.h>
#include <asm/pstate.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/spitfire.h>
#include <asm/processor.h>
#include <asm/thread_info.h>
#include <asm/mmu.h>
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
#include <asm/hypervisor.h>
[SPARC64]: arch/sparc64/kernel/trampoline.S needs asm/cpudata.h Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-14 16:55:49 +08:00
#include <asm/cpudata.h>
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
.data
.align 8
call_method:
.asciz "call-method"
.align 8
itlb_load:
.asciz "SUNW,itlb-load"
.align 8
dtlb_load:
.asciz "SUNW,dtlb-load"
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
/* XXX __cpuinit this thing XXX */
#define TRAMP_STACK_SIZE 1024
.align 16
tramp_stack:
.skip TRAMP_STACK_SIZE
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
.text
.align 8
.globl sparc64_cpu_startup, sparc64_cpu_startup_end
sparc64_cpu_startup:
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
BRANCH_IF_SUN4V(g1, niagara_startup)
BRANCH_IF_CHEETAH_BASE(g1, g5, cheetah_startup)
BRANCH_IF_CHEETAH_PLUS_OR_FOLLOWON(g1, g5, cheetah_plus_startup)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
ba,pt %xcc, spitfire_startup
nop
cheetah_plus_startup:
/* Preserve OBP chosen DCU and DCR register settings. */
ba,pt %xcc, cheetah_generic_startup
nop
cheetah_startup:
mov DCR_BPE | DCR_RPE | DCR_SI | DCR_IFPOE | DCR_MS, %g1
wr %g1, %asr18
sethi %uhi(DCU_ME|DCU_RE|DCU_HPE|DCU_SPE|DCU_SL|DCU_WE), %g5
or %g5, %ulo(DCU_ME|DCU_RE|DCU_HPE|DCU_SPE|DCU_SL|DCU_WE), %g5
sllx %g5, 32, %g5
or %g5, DCU_DM | DCU_IM | DCU_DC | DCU_IC, %g5
stxa %g5, [%g0] ASI_DCU_CONTROL_REG
membar #Sync
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
/* fallthru */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
cheetah_generic_startup:
mov TSB_EXTENSION_P, %g3
stxa %g0, [%g3] ASI_DMMU
stxa %g0, [%g3] ASI_IMMU
membar #Sync
mov TSB_EXTENSION_S, %g3
stxa %g0, [%g3] ASI_DMMU
membar #Sync
mov TSB_EXTENSION_N, %g3
stxa %g0, [%g3] ASI_DMMU
stxa %g0, [%g3] ASI_IMMU
membar #Sync
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
/* fallthru */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
niagara_startup:
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
/* Disable STICK_INT interrupts. */
sethi %hi(0x80000000), %g5
sllx %g5, 32, %g5
wr %g5, %asr25
ba,pt %xcc, startup_continue
nop
spitfire_startup:
mov (LSU_CONTROL_IC | LSU_CONTROL_DC | LSU_CONTROL_IM | LSU_CONTROL_DM), %g1
stxa %g1, [%g0] ASI_LSU_CONTROL
membar #Sync
startup_continue:
sethi %hi(0x80000000), %g2
sllx %g2, 32, %g2
wr %g2, 0, %tick_cmpr
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
mov %o0, %l0
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
BRANCH_IF_SUN4V(g1, niagara_lock_tlb)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
/* Call OBP by hand to lock KERNBASE into i/d tlbs.
* We lock 2 consequetive entries if we are 'bigkernel'.
*/
sethi %hi(prom_entry_lock), %g2
1: ldstub [%g2 + %lo(prom_entry_lock)], %g1
[SPARC64]: Avoid membar instructions in delay slots. In particular, avoid membar instructions in the delay slot of a jmpl instruction. UltraSPARC-I, II, IIi, and IIe have a bug, documented in the UltraSPARC-IIi User's Manual, Appendix K, Erratum 51 The long and short of it is that if the IMU unit misses on a branch or jmpl, and there is a store buffer synchronizing membar in the delay slot, the chip can stop fetching instructions. If interrupts are enabled or some other trap is enabled, the chip will unwedge itself, but performance will suffer. We already had a workaround for this bug in a few spots, but it's better to have the entire tree sanitized for this rule. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-06-28 06:42:04 +08:00
membar #StoreLoad | #StoreStore
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
brnz,pn %g1, 1b
[SPARC64]: Avoid membar instructions in delay slots. In particular, avoid membar instructions in the delay slot of a jmpl instruction. UltraSPARC-I, II, IIi, and IIe have a bug, documented in the UltraSPARC-IIi User's Manual, Appendix K, Erratum 51 The long and short of it is that if the IMU unit misses on a branch or jmpl, and there is a store buffer synchronizing membar in the delay slot, the chip can stop fetching instructions. If interrupts are enabled or some other trap is enabled, the chip will unwedge itself, but performance will suffer. We already had a workaround for this bug in a few spots, but it's better to have the entire tree sanitized for this rule. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-06-28 06:42:04 +08:00
nop
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
sethi %hi(p1275buf), %g2
or %g2, %lo(p1275buf), %g2
ldx [%g2 + 0x10], %l2
add %l2, -(192 + 128), %sp
flushw
sethi %hi(call_method), %g2
or %g2, %lo(call_method), %g2
stx %g2, [%sp + 2047 + 128 + 0x00]
mov 5, %g2
stx %g2, [%sp + 2047 + 128 + 0x08]
mov 1, %g2
stx %g2, [%sp + 2047 + 128 + 0x10]
sethi %hi(itlb_load), %g2
or %g2, %lo(itlb_load), %g2
stx %g2, [%sp + 2047 + 128 + 0x18]
[SPARC64]: Rewrite bootup sequence. Instead of all of this cpu-specific code to remap the kernel to the correct location, use portable firmware calls to do this instead. What we do now is the following in position independant assembler: chosen_node = prom_finddevice("/chosen"); prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu"); vaddr = 4MB_ALIGN(current_text_addr()); prom_translate(vaddr, &paddr_high, &paddr_low, &mode); prom_boot_mapping_mode = mode; prom_boot_mapping_phys_high = paddr_high; prom_boot_mapping_phys_low = paddr_low; prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low); and that replaces the massive amount of by-hand TLB probing and programming we used to do here. The new code should also handle properly the case where the kernel is mapped at the correct address already (think: future kexec support). Consequently, the bulk of remap_kernel() dies as does the entirety of arch/sparc64/prom/map.S We try to share some strings in the PROM library with the ones used at bootup, and while we're here mark input strings to oplib.h routines with "const" when appropriate. There are many more simplifications now possible. For one thing, we can consolidate the two copies we now have of a lot of cpu setup code sitting in head.S and trampoline.S. This is a significant step towards CONFIG_DEBUG_PAGEALLOC support. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-23 11:11:33 +08:00
sethi %hi(prom_mmu_ihandle_cache), %g2
lduw [%g2 + %lo(prom_mmu_ihandle_cache)], %g2
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
stx %g2, [%sp + 2047 + 128 + 0x20]
sethi %hi(KERNBASE), %g2
stx %g2, [%sp + 2047 + 128 + 0x28]
sethi %hi(kern_locked_tte_data), %g2
ldx [%g2 + %lo(kern_locked_tte_data)], %g2
stx %g2, [%sp + 2047 + 128 + 0x30]
mov 15, %g2
BRANCH_IF_ANY_CHEETAH(g1,g5,1f)
mov 63, %g2
1:
stx %g2, [%sp + 2047 + 128 + 0x38]
sethi %hi(p1275buf), %g2
or %g2, %lo(p1275buf), %g2
ldx [%g2 + 0x08], %o1
call %o1
add %sp, (2047 + 128), %o0
sethi %hi(bigkernel), %g2
lduw [%g2 + %lo(bigkernel)], %g2
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
brz,pt %g2, do_dtlb
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
nop
sethi %hi(call_method), %g2
or %g2, %lo(call_method), %g2
stx %g2, [%sp + 2047 + 128 + 0x00]
mov 5, %g2
stx %g2, [%sp + 2047 + 128 + 0x08]
mov 1, %g2
stx %g2, [%sp + 2047 + 128 + 0x10]
sethi %hi(itlb_load), %g2
or %g2, %lo(itlb_load), %g2
stx %g2, [%sp + 2047 + 128 + 0x18]
[SPARC64]: Rewrite bootup sequence. Instead of all of this cpu-specific code to remap the kernel to the correct location, use portable firmware calls to do this instead. What we do now is the following in position independant assembler: chosen_node = prom_finddevice("/chosen"); prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu"); vaddr = 4MB_ALIGN(current_text_addr()); prom_translate(vaddr, &paddr_high, &paddr_low, &mode); prom_boot_mapping_mode = mode; prom_boot_mapping_phys_high = paddr_high; prom_boot_mapping_phys_low = paddr_low; prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low); and that replaces the massive amount of by-hand TLB probing and programming we used to do here. The new code should also handle properly the case where the kernel is mapped at the correct address already (think: future kexec support). Consequently, the bulk of remap_kernel() dies as does the entirety of arch/sparc64/prom/map.S We try to share some strings in the PROM library with the ones used at bootup, and while we're here mark input strings to oplib.h routines with "const" when appropriate. There are many more simplifications now possible. For one thing, we can consolidate the two copies we now have of a lot of cpu setup code sitting in head.S and trampoline.S. This is a significant step towards CONFIG_DEBUG_PAGEALLOC support. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-23 11:11:33 +08:00
sethi %hi(prom_mmu_ihandle_cache), %g2
lduw [%g2 + %lo(prom_mmu_ihandle_cache)], %g2
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
stx %g2, [%sp + 2047 + 128 + 0x20]
sethi %hi(KERNBASE + 0x400000), %g2
stx %g2, [%sp + 2047 + 128 + 0x28]
sethi %hi(kern_locked_tte_data), %g2
ldx [%g2 + %lo(kern_locked_tte_data)], %g2
sethi %hi(0x400000), %g1
add %g2, %g1, %g2
stx %g2, [%sp + 2047 + 128 + 0x30]
mov 14, %g2
BRANCH_IF_ANY_CHEETAH(g1,g5,1f)
mov 62, %g2
1:
stx %g2, [%sp + 2047 + 128 + 0x38]
sethi %hi(p1275buf), %g2
or %g2, %lo(p1275buf), %g2
ldx [%g2 + 0x08], %o1
call %o1
add %sp, (2047 + 128), %o0
do_dtlb:
sethi %hi(call_method), %g2
or %g2, %lo(call_method), %g2
stx %g2, [%sp + 2047 + 128 + 0x00]
mov 5, %g2
stx %g2, [%sp + 2047 + 128 + 0x08]
mov 1, %g2
stx %g2, [%sp + 2047 + 128 + 0x10]
sethi %hi(dtlb_load), %g2
or %g2, %lo(dtlb_load), %g2
stx %g2, [%sp + 2047 + 128 + 0x18]
[SPARC64]: Rewrite bootup sequence. Instead of all of this cpu-specific code to remap the kernel to the correct location, use portable firmware calls to do this instead. What we do now is the following in position independant assembler: chosen_node = prom_finddevice("/chosen"); prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu"); vaddr = 4MB_ALIGN(current_text_addr()); prom_translate(vaddr, &paddr_high, &paddr_low, &mode); prom_boot_mapping_mode = mode; prom_boot_mapping_phys_high = paddr_high; prom_boot_mapping_phys_low = paddr_low; prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low); and that replaces the massive amount of by-hand TLB probing and programming we used to do here. The new code should also handle properly the case where the kernel is mapped at the correct address already (think: future kexec support). Consequently, the bulk of remap_kernel() dies as does the entirety of arch/sparc64/prom/map.S We try to share some strings in the PROM library with the ones used at bootup, and while we're here mark input strings to oplib.h routines with "const" when appropriate. There are many more simplifications now possible. For one thing, we can consolidate the two copies we now have of a lot of cpu setup code sitting in head.S and trampoline.S. This is a significant step towards CONFIG_DEBUG_PAGEALLOC support. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-23 11:11:33 +08:00
sethi %hi(prom_mmu_ihandle_cache), %g2
lduw [%g2 + %lo(prom_mmu_ihandle_cache)], %g2
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
stx %g2, [%sp + 2047 + 128 + 0x20]
sethi %hi(KERNBASE), %g2
stx %g2, [%sp + 2047 + 128 + 0x28]
sethi %hi(kern_locked_tte_data), %g2
ldx [%g2 + %lo(kern_locked_tte_data)], %g2
stx %g2, [%sp + 2047 + 128 + 0x30]
mov 15, %g2
BRANCH_IF_ANY_CHEETAH(g1,g5,1f)
mov 63, %g2
1:
stx %g2, [%sp + 2047 + 128 + 0x38]
sethi %hi(p1275buf), %g2
or %g2, %lo(p1275buf), %g2
ldx [%g2 + 0x08], %o1
call %o1
add %sp, (2047 + 128), %o0
sethi %hi(bigkernel), %g2
lduw [%g2 + %lo(bigkernel)], %g2
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
brz,pt %g2, do_unlock
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
nop
sethi %hi(call_method), %g2
or %g2, %lo(call_method), %g2
stx %g2, [%sp + 2047 + 128 + 0x00]
mov 5, %g2
stx %g2, [%sp + 2047 + 128 + 0x08]
mov 1, %g2
stx %g2, [%sp + 2047 + 128 + 0x10]
sethi %hi(dtlb_load), %g2
or %g2, %lo(dtlb_load), %g2
stx %g2, [%sp + 2047 + 128 + 0x18]
[SPARC64]: Rewrite bootup sequence. Instead of all of this cpu-specific code to remap the kernel to the correct location, use portable firmware calls to do this instead. What we do now is the following in position independant assembler: chosen_node = prom_finddevice("/chosen"); prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu"); vaddr = 4MB_ALIGN(current_text_addr()); prom_translate(vaddr, &paddr_high, &paddr_low, &mode); prom_boot_mapping_mode = mode; prom_boot_mapping_phys_high = paddr_high; prom_boot_mapping_phys_low = paddr_low; prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low); and that replaces the massive amount of by-hand TLB probing and programming we used to do here. The new code should also handle properly the case where the kernel is mapped at the correct address already (think: future kexec support). Consequently, the bulk of remap_kernel() dies as does the entirety of arch/sparc64/prom/map.S We try to share some strings in the PROM library with the ones used at bootup, and while we're here mark input strings to oplib.h routines with "const" when appropriate. There are many more simplifications now possible. For one thing, we can consolidate the two copies we now have of a lot of cpu setup code sitting in head.S and trampoline.S. This is a significant step towards CONFIG_DEBUG_PAGEALLOC support. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-23 11:11:33 +08:00
sethi %hi(prom_mmu_ihandle_cache), %g2
lduw [%g2 + %lo(prom_mmu_ihandle_cache)], %g2
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
stx %g2, [%sp + 2047 + 128 + 0x20]
sethi %hi(KERNBASE + 0x400000), %g2
stx %g2, [%sp + 2047 + 128 + 0x28]
sethi %hi(kern_locked_tte_data), %g2
ldx [%g2 + %lo(kern_locked_tte_data)], %g2
sethi %hi(0x400000), %g1
add %g2, %g1, %g2
stx %g2, [%sp + 2047 + 128 + 0x30]
mov 14, %g2
BRANCH_IF_ANY_CHEETAH(g1,g5,1f)
mov 62, %g2
1:
stx %g2, [%sp + 2047 + 128 + 0x38]
sethi %hi(p1275buf), %g2
or %g2, %lo(p1275buf), %g2
ldx [%g2 + 0x08], %o1
call %o1
add %sp, (2047 + 128), %o0
do_unlock:
sethi %hi(prom_entry_lock), %g2
stb %g0, [%g2 + %lo(prom_entry_lock)]
membar #StoreStore | #StoreLoad
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
ba,pt %xcc, after_lock_tlb
nop
niagara_lock_tlb:
[SPARC64]: Fix hypervisor call arg passing. Function goes in %o5, args go in %o0 --> %o5. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-10 14:57:21 +08:00
mov HV_FAST_MMU_MAP_PERM_ADDR, %o5
sethi %hi(KERNBASE), %o0
clr %o1
sethi %hi(kern_locked_tte_data), %o2
ldx [%o2 + %lo(kern_locked_tte_data)], %o2
mov HV_MMU_IMMU, %o3
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
ta HV_FAST_TRAP
[SPARC64]: Fix hypervisor call arg passing. Function goes in %o5, args go in %o0 --> %o5. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-10 14:57:21 +08:00
mov HV_FAST_MMU_MAP_PERM_ADDR, %o5
sethi %hi(KERNBASE), %o0
clr %o1
sethi %hi(kern_locked_tte_data), %o2
ldx [%o2 + %lo(kern_locked_tte_data)], %o2
mov HV_MMU_DMMU, %o3
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
ta HV_FAST_TRAP
sethi %hi(bigkernel), %g2
lduw [%g2 + %lo(bigkernel)], %g2
brz,pt %g2, after_lock_tlb
nop
[SPARC64]: Fix hypervisor call arg passing. Function goes in %o5, args go in %o0 --> %o5. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-10 14:57:21 +08:00
mov HV_FAST_MMU_MAP_PERM_ADDR, %o5
sethi %hi(KERNBASE + 0x400000), %o0
clr %o1
sethi %hi(kern_locked_tte_data), %o2
ldx [%o2 + %lo(kern_locked_tte_data)], %o2
sethi %hi(0x400000), %o3
add %o2, %o3, %o2
mov HV_MMU_IMMU, %o3
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
ta HV_FAST_TRAP
[SPARC64]: Fix hypervisor call arg passing. Function goes in %o5, args go in %o0 --> %o5. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-10 14:57:21 +08:00
mov HV_FAST_MMU_MAP_PERM_ADDR, %o5
sethi %hi(KERNBASE + 0x400000), %o0
clr %o1
sethi %hi(kern_locked_tte_data), %o2
ldx [%o2 + %lo(kern_locked_tte_data)], %o2
sethi %hi(0x400000), %o3
add %o2, %o3, %o2
mov HV_MMU_DMMU, %o3
[SPARC64]: Detect sun4v early in boot process. We look for "SUNW,sun4v" in the 'compatible' property of the root OBP device tree node. Protect every %ver register access, to make sure it is not touched on sun4v, as %ver is hyperprivileged there. Lock kernel TLB entries using hypervisor calls instead of calls into OBP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-09 18:52:44 +08:00
ta HV_FAST_TRAP
after_lock_tlb:
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
wrpr %g0, (PSTATE_PRIV | PSTATE_PEF), %pstate
wr %g0, 0, %fprs
wr %g0, ASI_P, %asi
mov PRIMARY_CONTEXT, %g7
[SPARC64]: Patch up mmu context register writes for sun4v. sun4v uses ASI_MMU instead of ASI_DMMU Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 14:13:05 +08:00
661: stxa %g0, [%g7] ASI_DMMU
.section .sun4v_1insn_patch, "ax"
.word 661b
stxa %g0, [%g7] ASI_MMU
.previous
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
membar #Sync
mov SECONDARY_CONTEXT, %g7
[SPARC64]: Patch up mmu context register writes for sun4v. sun4v uses ASI_MMU instead of ASI_DMMU Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 14:13:05 +08:00
661: stxa %g0, [%g7] ASI_DMMU
.section .sun4v_1insn_patch, "ax"
.word 661b
stxa %g0, [%g7] ASI_MMU
.previous
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
membar #Sync
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
/* Everything we do here, until we properly take over the
* trap table, must be done with extreme care. We cannot
* make any references to %g6 (current thread pointer),
* %g4 (current task pointer), or %g5 (base of current cpu's
* per-cpu area) until we properly take over the trap table
* from the firmware and hypervisor.
*
* Get onto temporary stack which is in the locked kernel image.
*/
sethi %hi(tramp_stack), %g1
or %g1, %lo(tramp_stack), %g1
add %g1, TRAMP_STACK_SIZE, %g1
sub %g1, STACKFRAME_SZ + STACK_BIAS, %sp
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
mov 0, %fp
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
/* Put garbage in these registers to trap any access to them. */
set 0xdeadbeef, %g4
set 0xdeadbeef, %g5
set 0xdeadbeef, %g6
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
call init_irqwork_curcpu
nop
[SPARC64]: Allocate and register the 4 sun4v mondo queues at bootup. Needs to occur before we enable PSTATE_IE in %pstate. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 16:08:23 +08:00
sethi %hi(tlb_type), %g3
lduw [%g3 + %lo(tlb_type)], %g2
cmp %g2, 3
bne,pt %icc, 1f
nop
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
call hard_smp_processor_id
nop
mov %o0, %o1
mov 0, %o0
mov 0, %o2
[SPARC64]: Allocate and register the 4 sun4v mondo queues at bootup. Needs to occur before we enable PSTATE_IE in %pstate. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 16:08:23 +08:00
call sun4v_init_mondo_queues
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
mov 1, %o3
[SPARC64]: Allocate and register the 4 sun4v mondo queues at bootup. Needs to occur before we enable PSTATE_IE in %pstate. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 16:08:23 +08:00
1: call init_cur_cpu_trap
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
ldx [%l0], %o0
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
[SPARC64]: Replace cheetah+ code patching with variables. Instead of code patching to handle the page size fields in the context registers, just use variables from which we get the proper values. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-10-05 06:23:20 +08:00
/* Start using proper page size encodings in ctx register. */
[SPARC64]: Patch up mmu context register writes for sun4v. sun4v uses ASI_MMU instead of ASI_DMMU Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-08 14:13:05 +08:00
sethi %hi(sparc64_kern_pri_context), %g3
ldx [%g3 + %lo(sparc64_kern_pri_context)], %g2
mov PRIMARY_CONTEXT, %g1
661: stxa %g2, [%g1] ASI_DMMU
.section .sun4v_1insn_patch, "ax"
.word 661b
stxa %g2, [%g1] ASI_MMU
.previous
membar #Sync
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
wrpr %g0, 0, %wstate
/* As a hack, put &init_thread_union into %g6.
* prom_world() loads from here to restore the %asi
* register.
*/
sethi %hi(init_thread_union), %g6
or %g6, %lo(init_thread_union), %g6
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
[SPARC64]: Use ASI_SCRATCHPAD address 0x0 properly. This is where the virtual address of the fault status area belongs. To set it up we don't make a hypervisor call, instead we call OBP's SUNW,set-trap-table with the real address of the fault status area as the second argument. And right before that call we write the virtual address into ASI_SCRATCHPAD vaddr 0x0. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-11 07:39:51 +08:00
sethi %hi(is_sun4v), %o0
lduw [%o0 + %lo(is_sun4v)], %o0
brz,pt %o0, 1f
nop
TRAP_LOAD_TRAP_BLOCK(%g2, %g3)
add %g2, TRAP_PER_CPU_FAULT_INFO, %g2
stxa %g2, [%g0] ASI_SCRATCHPAD
/* Compute physical address:
*
* paddr = kern_base + (mmfsa_vaddr - KERNBASE)
*/
sethi %hi(KERNBASE), %g3
sub %g2, %g3, %g2
sethi %hi(kern_base), %g3
ldx [%g3 + %lo(kern_base)], %g3
add %g2, %g3, %o1
call prom_set_trap_table_sun4v
sethi %hi(sparc64_ttable_tl0), %o0
ba,pt %xcc, 2f
nop
1: call prom_set_trap_table
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
sethi %hi(sparc64_ttable_tl0), %o0
[SPARC64]: Get SUN4V SMP working. The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-02-17 17:29:17 +08:00
2: ldx [%l0], %g6
ldx [%g6 + TI_TASK], %g4
mov 1, %g5
sllx %g5, THREAD_SHIFT, %g5
sub %g5, (STACKFRAME_SZ + STACK_BIAS), %g5
add %g6, %g5, %sp
mov 0, %fp
rdpr %pstate, %o1
or %o1, PSTATE_IE, %o1
wrpr %o1, 0, %pstate
call smp_callin
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
nop
call cpu_idle
mov 0, %o0
call cpu_panic
nop
1: b,a,pt %xcc, 1b
.align 8
sparc64_cpu_startup_end:
Copy Permalink