AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
f7b200af8f
kernel_optimize_test/arch/powerpc/include/asm/kdump.h

48 lines
1.4 KiB
C
Raw Normal View History

[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
#ifndef _PPC64_KDUMP_H
#define _PPC64_KDUMP_H
powerpc/32: Wire up the trampoline code for kdump Wire up the trampoline code for ppc32 to relay exceptions from the vectors at address 0 to vectors at address 32MB, and modify Kconfig to enable Kdump support for all classic powerpcs. Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-12-17 18:09:26 +08:00
#include <asm/page.h>
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
/* Kdump kernel runs at 32 MB, change at your peril. */
#define KDUMP_KERNELBASE 0x2000000
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
/* How many bytes to reserve at zero for kdump. The reserve limit should
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
* be greater or equal to the trampoline's end address.
* Reserve to the end of the FWNMI area, see head_64.S */
[POWERPC] kdump: Support kernels having 64k page size. This is required to generate proper core files using kdump on ppc64. Create a backup region of 64K size irrespective of the PAGE SIZE. At present 32K was used as backup size. In the case of 64K page size, second PT_LOAD segments starts at 32K and the first one is not page aligned. __ioremap() (crash_dump.c) fails if pfn = 0 which is the case for the second PT_LOAD segment. This is not an issue for 4K page size because the the first page (32K backup) is copied to second kernel memory and thus referencing with the second kernel pfn. Signed-off-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-09-08 10:29:52 +08:00
#define KDUMP_RESERVE_LIMIT 0x10000 /* 64K */
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
#ifdef CONFIG_CRASH_DUMP
powerpc/32: Wire up the trampoline code for kdump Wire up the trampoline code for ppc32 to relay exceptions from the vectors at address 0 to vectors at address 32MB, and modify Kconfig to enable Kdump support for all classic powerpcs. Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-12-17 18:09:26 +08:00
/*
* On PPC64 translation is disabled during trampoline setup, so we use
* physical addresses. Though on PPC32 translation is already enabled,
* so we can't do the same. Luckily create_trampoline() creates relative
* branches, so we can just add the PAGE_OFFSET and don't worry about it.
*/
#ifdef __powerpc64__
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
#define KDUMP_TRAMPOLINE_START 0x0100
#define KDUMP_TRAMPOLINE_END 0x3000
powerpc/32: Wire up the trampoline code for kdump Wire up the trampoline code for ppc32 to relay exceptions from the vectors at address 0 to vectors at address 32MB, and modify Kconfig to enable Kdump support for all classic powerpcs. Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-12-17 18:09:26 +08:00
#else
#define KDUMP_TRAMPOLINE_START (0x0100 + PAGE_OFFSET)
#define KDUMP_TRAMPOLINE_END (0x3000 + PAGE_OFFSET)
#endif /* __powerpc64__ */
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
[POWERPC] kdump: Reserve the existing TCE mappings left by the first kernel During kdump boot, noticed some machines checkstop on dma protection fault for ongoing DMA left in the first kernel. Instead of initializing TCE entries in iommu_init() for the kdump boot, this patch fixes this issue by walking through the each TCE table and checks whether the entries are in use by the first kernel. If so, reserve those entries by setting the corresponding bit in tbl->it_map such that these entries will not be available for the kdump boot. However it could be possible that all TCE entries might be used up due to the driver bug that does continuous mapping. My observation is around 1700 TCE entries are used on some systems (Ex: P4) at some point of time during kdump boot and saving dump (either write into the disk or sending to remote machine). Hence, this patch will make sure that minimum of 2048 entries will be available such that kdump boot could be successful in some cases. Signed-off-by: Haren Myneni <haren@us.ibm.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-23 14:35:10 +08:00
#define KDUMP_MIN_TCE_ENTRIES 2048
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
#endif /* CONFIG_CRASH_DUMP */
#ifndef __ASSEMBLY__
powerpc: Support for relocatable kdump kernel This adds relocatable kernel support for kdump. With this one can use the same regular kernel to capture the kdump. A signature (0xfeed1234) is passed in r6 from panic code to the next kernel through kexec_sequence and purgatory code. The signature is used to differentiate between kdump kernel and non-kdump kernels. The purgatory code compares the signature and sets the __kdump_flag in head_64.S. During the boot up, kernel code checks __kdump_flag and if it is set, the kernel will behave as relocatable kdump kernel. This kernel will boot at the address where it was loaded by kexec-tools ie. at the address reserved through crashkernel boot parameter. CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump kernel as relocatable. So the same kernel can be used as production and kdump kernel. This patch incorporates the changes suggested by Paul Mackerras to avoid GOT use and to avoid two copies of the code. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Mohan Kumar M <mohan@in.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-22 01:38:10 +08:00
#if defined(CONFIG_CRASH_DUMP) && !defined(CONFIG_RELOCATABLE)
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
extern void reserve_kdump_trampoline(void);
extern void setup_kdump_trampoline(void);
powerpc: Support for relocatable kdump kernel This adds relocatable kernel support for kdump. With this one can use the same regular kernel to capture the kdump. A signature (0xfeed1234) is passed in r6 from panic code to the next kernel through kexec_sequence and purgatory code. The signature is used to differentiate between kdump kernel and non-kdump kernels. The purgatory code compares the signature and sets the __kdump_flag in head_64.S. During the boot up, kernel code checks __kdump_flag and if it is set, the kernel will behave as relocatable kdump kernel. This kernel will boot at the address where it was loaded by kexec-tools ie. at the address reserved through crashkernel boot parameter. CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump kernel as relocatable. So the same kernel can be used as production and kdump kernel. This patch incorporates the changes suggested by Paul Mackerras to avoid GOT use and to avoid two copies of the code. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Mohan Kumar M <mohan@in.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-22 01:38:10 +08:00
#else
/* !CRASH_DUMP || RELOCATABLE */
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
static inline void reserve_kdump_trampoline(void) { ; }
static inline void setup_kdump_trampoline(void) { ; }
powerpc: Support for relocatable kdump kernel This adds relocatable kernel support for kdump. With this one can use the same regular kernel to capture the kdump. A signature (0xfeed1234) is passed in r6 from panic code to the next kernel through kexec_sequence and purgatory code. The signature is used to differentiate between kdump kernel and non-kdump kernels. The purgatory code compares the signature and sets the __kdump_flag in head_64.S. During the boot up, kernel code checks __kdump_flag and if it is set, the kernel will behave as relocatable kdump kernel. This kernel will boot at the address where it was loaded by kexec-tools ie. at the address reserved through crashkernel boot parameter. CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump kernel as relocatable. So the same kernel can be used as production and kdump kernel. This patch incorporates the changes suggested by Paul Mackerras to avoid GOT use and to avoid two copies of the code. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Mohan Kumar M <mohan@in.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-22 01:38:10 +08:00
#endif
[PATCH] powerpc: Kdump header cleanup We need to know the base address of the kdump kernel even when we're not a kdump kernel, so add a #define for it. Move the logic that sets the kdump kernelbase into kdump.h instead of page.h. Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's doing, and add an empty definition for the !CRASH_DUMP case to avoid a Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-17 16:00:49 +08:00
#endif /* __ASSEMBLY__ */
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset Regardless of where the kernel's linked we always get interrupts at low addresses. This patch creates a trampoline in the first 3 pages of memory, where interrupts land, and patches those addresses to jump into the real kernel code at PHYSICAL_START. We also need to reserve the trampoline code and a bit more in prom.c Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-12-04 15:39:37 +08:00
#endif /* __PPC64_KDUMP_H */
Copy Permalink