From d8207c155a7c6015eb7f43739baa7dfb1fa638af Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Mon, 24 Feb 2020 14:07:48 +0000 Subject: [PATCH 1/7] backlight: lp855x: Ensure regulators are disabled on probe failure If probing the LP885x backlight fails after the regulators have been enabled, then the following warning is seen when releasing the regulators ... WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160 Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6 CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1 Hardware name: NVIDIA Jetson TX1 Developer Kit (DT) ... Call trace: _regulator_put.part.28+0x158/0x160 regulator_put+0x34/0x50 devm_regulator_release+0x10/0x18 release_nodes+0x12c/0x230 devres_release_all+0x34/0x50 really_probe+0x1c0/0x370 driver_probe_device+0x58/0x100 device_driver_attach+0x6c/0x78 __driver_attach+0xb0/0xf0 bus_for_each_dev+0x68/0xc8 driver_attach+0x20/0x28 bus_add_driver+0x160/0x1f0 driver_register+0x60/0x110 i2c_register_driver+0x40/0x80 lp855x_driver_init+0x20/0x1000 [lp855x_bl] do_one_initcall+0x58/0x1a0 do_init_module+0x54/0x1d0 load_module+0x1d80/0x21c8 __do_sys_finit_module+0xe8/0x100 __arm64_sys_finit_module+0x18/0x20 el0_svc_common.constprop.3+0xb0/0x168 do_el0_svc+0x20/0x98 el0_sync_handler+0xf4/0x1b0 el0_sync+0x140/0x180 Fix this by ensuring that the regulators are disabled, if enabled, on probe failure. Finally, ensure that the vddio regulator is disabled in the driver remove handler. Signed-off-by: Jon Hunter Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones --- drivers/video/backlight/lp855x_bl.c | 20 ++++++++++++++++---- 1 file changed, 16 insertions(+), 4 deletions(-) diff --git a/drivers/video/backlight/lp855x_bl.c b/drivers/video/backlight/lp855x_bl.c index f68920131a4a..e94932c69f54 100644 --- a/drivers/video/backlight/lp855x_bl.c +++ b/drivers/video/backlight/lp855x_bl.c @@ -456,7 +456,7 @@ static int lp855x_probe(struct i2c_client *cl, const struct i2c_device_id *id) ret = regulator_enable(lp->enable); if (ret < 0) { dev_err(lp->dev, "failed to enable vddio: %d\n", ret); - return ret; + goto disable_supply; } /* @@ -471,24 +471,34 @@ static int lp855x_probe(struct i2c_client *cl, const struct i2c_device_id *id) ret = lp855x_configure(lp); if (ret) { dev_err(lp->dev, "device config err: %d", ret); - return ret; + goto disable_vddio; } ret = lp855x_backlight_register(lp); if (ret) { dev_err(lp->dev, "failed to register backlight. err: %d\n", ret); - return ret; + goto disable_vddio; } ret = sysfs_create_group(&lp->dev->kobj, &lp855x_attr_group); if (ret) { dev_err(lp->dev, "failed to register sysfs. err: %d\n", ret); - return ret; + goto disable_vddio; } backlight_update_status(lp->bl); + return 0; + +disable_vddio: + if (lp->enable) + regulator_disable(lp->enable); +disable_supply: + if (lp->supply) + regulator_disable(lp->supply); + + return ret; } static int lp855x_remove(struct i2c_client *cl) @@ -497,6 +507,8 @@ static int lp855x_remove(struct i2c_client *cl) lp->bl->props.brightness = 0; backlight_update_status(lp->bl); + if (lp->enable) + regulator_disable(lp->enable); if (lp->supply) regulator_disable(lp->supply); sysfs_remove_group(&lp->dev->kobj, &lp855x_attr_group); From 61365ca7b24f1cb106a4c619c94610862bbec778 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Wed, 15 Apr 2020 14:14:49 +0200 Subject: [PATCH 2/7] backlight: l4f00242t03: Convert to GPIO descriptors This converts the l4f00242t03 backlight driver to use GPIO descriptors and switches the two Freescale i.MX boards over to passing descriptors instead of global GPIO numbers. We use the typical names "enable" and "reset" as found in the device tree bindings for panel GPIOs. This saves a lot of code in the driver and makes it possible to get rid of the platform data header altogether. Signed-off-by: Linus Walleij Reviewed-by: Daniel Thompson Acked-by: Shawn Guo Signed-off-by: Lee Jones --- arch/arm/mach-imx/mach-mx27_3ds.c | 21 +++++++++---- arch/arm/mach-imx/mach-mx31_3ds.c | 24 +++++++++++--- drivers/video/backlight/l4f00242t03.c | 45 +++++++++++---------------- include/linux/spi/l4f00242t03.h | 17 ---------- 4 files changed, 52 insertions(+), 55 deletions(-) delete mode 100644 include/linux/spi/l4f00242t03.h diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c index 7b8325fb5b41..1da5f07952ac 100644 --- a/arch/arm/mach-imx/mach-mx27_3ds.c +++ b/arch/arm/mach-imx/mach-mx27_3ds.c @@ -13,6 +13,7 @@ #include #include +#include #include #include #include @@ -20,8 +21,6 @@ #include #include #include -#include - #include #include @@ -351,9 +350,19 @@ static const struct imx_fb_platform_data mx27_3ds_fb_data __initconst = { }; /* LCD */ -static struct l4f00242t03_pdata mx27_3ds_lcd_pdata = { - .reset_gpio = LCD_RESET, - .data_enable_gpio = LCD_ENABLE, +static struct gpiod_lookup_table mx27_3ds_lcd_gpiod_table = { + .dev_id = "spi0.0", /* Bus 0 chipselect 0 */ + .table = { + /* + * The i.MX27 has the i.MX21 GPIO controller, the GPIOs + * numbered IMX_GPIO_NR(1, 3) and IMX_GPIO_NR(1, 31) + * are in "bank 1" which is subtracted by one in the macro + * so these are actually bank 0 on "imx21-gpio.0". + */ + GPIO_LOOKUP("imx21-gpio.0", 3, "reset", GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("imx21-gpio.0", 31, "enable", GPIO_ACTIVE_HIGH), + { }, + }, }; static struct spi_board_info mx27_3ds_spi_devs[] __initdata = { @@ -370,7 +379,6 @@ static struct spi_board_info mx27_3ds_spi_devs[] __initdata = { .max_speed_hz = 5000000, .bus_num = 0, .chip_select = 0, /* SS0 */ - .platform_data = &mx27_3ds_lcd_pdata, }, }; @@ -416,6 +424,7 @@ static void __init mx27pdk_late_init(void) if (!otg_mode_host) imx27_add_fsl_usb2_udc(&otg_device_pdata); + gpiod_add_lookup_table(&mx27_3ds_lcd_gpiod_table); mx27_3ds_spi_devs[0].irq = gpio_to_irq(PMIC_INT); spi_register_board_info(mx27_3ds_spi_devs, ARRAY_SIZE(mx27_3ds_spi_devs)); diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c index 716d2ad51103..e81386190479 100644 --- a/arch/arm/mach-imx/mach-mx31_3ds.c +++ b/arch/arm/mach-imx/mach-mx31_3ds.c @@ -10,10 +10,10 @@ #include #include #include +#include #include #include #include -#include #include #include #include @@ -160,9 +160,23 @@ static struct mx3fb_platform_data mx3fb_pdata __initdata = { }; /* LCD */ -static struct l4f00242t03_pdata mx31_3ds_l4f00242t03_pdata = { - .reset_gpio = IOMUX_TO_GPIO(MX31_PIN_LCS1), - .data_enable_gpio = IOMUX_TO_GPIO(MX31_PIN_SER_RS), +static struct gpiod_lookup_table mx31_3ds_lcd_gpiod_table = { + .dev_id = "spi0.2", /* Bus 0 chipselect 2 */ + .table = { + /* + * "reset" has IOMUX_TO_GPIO(IOMUX_PIN(88, 28)). + * The macro only shifts 88 to bits 9..16 and then + * mask it and shift it back. The GPIO number is 88. + * 88 is 2*32+24 + */ + GPIO_LOOKUP("imx31-gpio.2", 24, "reset", GPIO_ACTIVE_HIGH), + /* + * Same reasoning as above for + * IOMUX_TO_GPIO(IOMUX_PIN(89, 27), pin 89 is 2*32+25. + */ + GPIO_LOOKUP("imx31-gpio.2", 25, "enable", GPIO_ACTIVE_HIGH), + { }, + }, }; /* @@ -387,7 +401,6 @@ static struct spi_board_info mx31_3ds_spi_devs[] __initdata = { .max_speed_hz = 5000000, .bus_num = 0, .chip_select = 2, /* SS2 */ - .platform_data = &mx31_3ds_l4f00242t03_pdata, }, }; @@ -566,6 +579,7 @@ static void __init mx31_3ds_init(void) static void __init mx31_3ds_late(void) { + gpiod_add_lookup_table(&mx31_3ds_lcd_gpiod_table); mx31_3ds_spi_devs[0].irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3)); spi_register_board_info(mx31_3ds_spi_devs, ARRAY_SIZE(mx31_3ds_spi_devs)); diff --git a/drivers/video/backlight/l4f00242t03.c b/drivers/video/backlight/l4f00242t03.c index 8554b4aa980c..46f97d1c3d21 100644 --- a/drivers/video/backlight/l4f00242t03.c +++ b/drivers/video/backlight/l4f00242t03.c @@ -14,13 +14,11 @@ #include #include #include -#include +#include #include #include #include - #include -#include struct l4f00242t03_priv { struct spi_device *spi; @@ -28,16 +26,18 @@ struct l4f00242t03_priv { int lcd_state; struct regulator *io_reg; struct regulator *core_reg; + struct gpio_desc *reset; + struct gpio_desc *enable; }; -static void l4f00242t03_reset(unsigned int gpio) +static void l4f00242t03_reset(struct gpio_desc *gpiod) { pr_debug("l4f00242t03_reset.\n"); - gpio_set_value(gpio, 1); + gpiod_set_value(gpiod, 1); mdelay(100); - gpio_set_value(gpio, 0); + gpiod_set_value(gpiod, 0); mdelay(10); /* tRES >= 100us */ - gpio_set_value(gpio, 1); + gpiod_set_value(gpiod, 1); mdelay(20); } @@ -45,7 +45,6 @@ static void l4f00242t03_reset(unsigned int gpio) static void l4f00242t03_lcd_init(struct spi_device *spi) { - struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev); struct l4f00242t03_priv *priv = spi_get_drvdata(spi); const u16 cmd[] = { 0x36, param(0), 0x3A, param(0x60) }; int ret; @@ -76,21 +75,20 @@ static void l4f00242t03_lcd_init(struct spi_device *spi) return; } - l4f00242t03_reset(pdata->reset_gpio); + l4f00242t03_reset(priv->reset); - gpio_set_value(pdata->data_enable_gpio, 1); + gpiod_set_value(priv->enable, 1); msleep(60); spi_write(spi, (const u8 *)cmd, ARRAY_SIZE(cmd) * sizeof(u16)); } static void l4f00242t03_lcd_powerdown(struct spi_device *spi) { - struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev); struct l4f00242t03_priv *priv = spi_get_drvdata(spi); dev_dbg(&spi->dev, "Powering down LCD\n"); - gpio_set_value(pdata->data_enable_gpio, 0); + gpiod_set_value(priv->enable, 0); regulator_disable(priv->io_reg); regulator_disable(priv->core_reg); @@ -168,13 +166,6 @@ static struct lcd_ops l4f_ops = { static int l4f00242t03_probe(struct spi_device *spi) { struct l4f00242t03_priv *priv; - struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev); - int ret; - - if (pdata == NULL) { - dev_err(&spi->dev, "Uninitialized platform data.\n"); - return -EINVAL; - } priv = devm_kzalloc(&spi->dev, sizeof(struct l4f00242t03_priv), GFP_KERNEL); @@ -187,21 +178,21 @@ static int l4f00242t03_probe(struct spi_device *spi) priv->spi = spi; - ret = devm_gpio_request_one(&spi->dev, pdata->reset_gpio, - GPIOF_OUT_INIT_HIGH, "lcd l4f00242t03 reset"); - if (ret) { + priv->reset = devm_gpiod_get(&spi->dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(priv->reset)) { dev_err(&spi->dev, "Unable to get the lcd l4f00242t03 reset gpio.\n"); - return ret; + return PTR_ERR(priv->reset); } + gpiod_set_consumer_name(priv->reset, "lcd l4f00242t03 reset"); - ret = devm_gpio_request_one(&spi->dev, pdata->data_enable_gpio, - GPIOF_OUT_INIT_LOW, "lcd l4f00242t03 data enable"); - if (ret) { + priv->enable = devm_gpiod_get(&spi->dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(priv->enable)) { dev_err(&spi->dev, "Unable to get the lcd l4f00242t03 data en gpio.\n"); - return ret; + return PTR_ERR(priv->enable); } + gpiod_set_consumer_name(priv->enable, "lcd l4f00242t03 data enable"); priv->io_reg = devm_regulator_get(&spi->dev, "vdd"); if (IS_ERR(priv->io_reg)) { diff --git a/include/linux/spi/l4f00242t03.h b/include/linux/spi/l4f00242t03.h deleted file mode 100644 index 831a5de7a0e2..000000000000 --- a/include/linux/spi/l4f00242t03.h +++ /dev/null @@ -1,17 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ -/* - * l4f00242t03.h -- Platform glue for Epson L4F00242T03 LCD - * - * Copyright (c) 2009 Alberto Panizzo - * Based on Marek Vasut work in lms283gf05.h -*/ - -#ifndef _INCLUDE_LINUX_SPI_L4F00242T03_H_ -#define _INCLUDE_LINUX_SPI_L4F00242T03_H_ - -struct l4f00242t03_pdata { - unsigned int reset_gpio; - unsigned int data_enable_gpio; -}; - -#endif /* _INCLUDE_LINUX_SPI_L4F00242T03_H_ */ From e0ace1fc40cd5775299ea621cb180d821dc3d4b9 Mon Sep 17 00:00:00 2001 From: Kiran Gunda Date: Thu, 23 Apr 2020 21:03:34 +0530 Subject: [PATCH 3/7] dt-bindings: backlight: qcom-wled: Convert the wled bindings to .yaml format Convert the qcom-wled bindings from .txt to .yaml format. Also replace PM8941 to WLED3 and PMI8998 to WLED4. Signed-off-by: Kiran Gunda Signed-off-by: Subbaraman Narayanamurthy Acked-by: Daniel Thompson Reviewed-by: Rob Herring Signed-off-by: Lee Jones --- .../bindings/leds/backlight/qcom-wled.txt | 154 ------------- .../bindings/leds/backlight/qcom-wled.yaml | 208 ++++++++++++++++++ 2 files changed, 208 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted file mode 100644 index c06863badfbd..000000000000 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt +++ /dev/null @@ -1,154 +0,0 @@ -Binding for Qualcomm Technologies, Inc. WLED driver - -WLED (White Light Emitting Diode) driver is used for controlling display -backlight that is part of PMIC on Qualcomm Technologies, Inc. reference -platforms. The PMIC is connected to the host processor via SPMI bus. - -- compatible - Usage: required - Value type: - Definition: should be one of: - "qcom,pm8941-wled" - "qcom,pmi8998-wled" - "qcom,pm660l-wled" - -- reg - Usage: required - Value type: - Definition: Base address of the WLED modules. - -- default-brightness - Usage: optional - Value type: - Definition: brightness value on boot, value from: 0-4095. - Default: 2048 - -- label - Usage: required - Value type: - Definition: The name of the backlight device - -- qcom,cs-out - Usage: optional - Value type: - Definition: enable current sink output. - This property is supported only for PM8941. - -- qcom,cabc - Usage: optional - Value type: - Definition: enable content adaptive backlight control. - -- qcom,ext-gen - Usage: optional - Value type: - Definition: use externally generated modulator signal to dim. - This property is supported only for PM8941. - -- qcom,current-limit - Usage: optional - Value type: - Definition: mA; per-string current limit; value from 0 to 25 with - 1 mA step. Default 20 mA. - This property is supported only for pm8941. - -- qcom,current-limit-microamp - Usage: optional - Value type: - Definition: uA; per-string current limit; value from 0 to 30000 with - 2500 uA step. Default 25 mA. - -- qcom,current-boost-limit - Usage: optional - Value type: - Definition: mA; boost current limit. - For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA. - For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA. - -- qcom,switching-freq - Usage: optional - Value type: - Definition: kHz; switching frequency; one of: 600, 640, 685, 738, - 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, - 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz - -- qcom,ovp - Usage: optional - Value type: - Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. Default: 29V - This property is supported only for PM8941. - -- qcom,ovp-millivolt - Usage: optional - Value type: - Definition: mV; Over-voltage protection limit; - For pmi8998: one of 18100, 19600, 29600, 31100. - Default 29600 mV. - If this property is not specified for PM8941, it - falls back to "qcom,ovp" property. - -- qcom,num-strings - Usage: optional - Value type: - Definition: #; number of led strings attached; - value: For PM8941 from 1 to 3. Default: 2 - For PMI8998 from 1 to 4. - -- interrupts - Usage: optional - Value type: - Definition: Interrupts associated with WLED. This should be - "short" and "ovp" interrupts. Interrupts can be - specified as per the encoding listed under - Documentation/devicetree/bindings/spmi/ - qcom,spmi-pmic-arb.txt. - -- interrupt-names - Usage: optional - Value type: - Definition: Interrupt names associated with the interrupts. - Must be "short" and "ovp". The short circuit detection - is not supported for PM8941. - -- qcom,enabled-strings - Usage: optional - Value tyoe: - Definition: Array of the WLED strings numbered from 0 to 3. Each - string of leds are operated individually. Specify the - list of strings used by the device. Any combination of - led strings can be used. - -- qcom,external-pfet - Usage: optional - Value type: - Definition: Specify if external PFET control for short circuit - protection is used. This property is supported only - for PMI8998. - -- qcom,auto-string-detection - Usage: optional - Value type: - Definition: Enables auto-detection of the WLED string configuration. - This feature is not supported for PM8941. - - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; - qcom,enabled-strings = <0 1>; -}; diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file mode 100644 index 000000000000..b835443b3c2c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml @@ -0,0 +1,208 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Qualcomm Technologies, Inc. WLED driver + +maintainers: + - Bjorn Andersson + - Kiran Gunda + +description: | + WLED (White Light Emitting Diode) driver is used for controlling display + backlight that is part of PMIC on Qualcomm Technologies, Inc. reference + platforms. The PMIC is connected to the host processor via SPMI bus. + +properties: + compatible: + enum: + - qcom,pm8941-wled + - qcom,pmi8998-wled + - qcom,pm660l-wled + + reg: + maxItems: 1 + + default-brightness: + description: | + brightness value on boot. + minimum: 0 + maximum: 4095 + default: 2048 + + label: true + + qcom,cs-out: + description: | + enable current sink output. + This property is supported only for WLED3. + type: boolean + + qcom,cabc: + description: | + enable content adaptive backlight control. + type: boolean + + qcom,ext-gen: + description: | + use externally generated modulator signal to dim. + This property is supported only for WLED3. + type: boolean + + qcom,current-limit: + description: | + mA; per-string current limit. + This property is supported only for WLED3. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + default: 20 + minimum: 0 + maximum: 25 + + qcom,current-limit-microamp: + description: | + uA; per-string current limit. + default: 25 + minimum: 0 + maximum: 30000 + multipleOf: 25 + + qcom,current-boost-limit: + description: | + mA; boost current limit. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,switching-freq: + description: | + kHz; switching frequency. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ] + + qcom,ovp: + description: | + V; Over-voltage protection limit. + This property is supported only for WLED3. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 27, 29, 32, 35 ] + - default: 29 + + qcom,ovp-millivolt: + description: | + Over-voltage protection limit. This property is for WLED4 only. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 18100, 19600, 29600, 31100 ] + - default: 29600 + + qcom,num-strings: + description: | + number of led strings attached. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,enabled-strings: + description: | + Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + + qcom,external-pfet: + description: | + Specify if external PFET control for short circuit + protection is used. This property is supported only + for WLED4. + type: boolean + + qcom,auto-string-detection: + description: | + Enables auto-detection of the WLED string configuration. + This feature is not supported for WLED3. + type: boolean + + interrupts: + minItems: 1 + items: + - description: over voltage protection interrupt. + - description: short circuit interrupt. + + interrupt-names: + minItems: 1 + items: + - const: ovp + - const: short + +allOf: + - if: + properties: + compatible: + contains: + const: qcom,pm8941-wled + + then: + properties: + qcom,current-boost-limit: + enum: [ 105, 385, 525, 805, 980, 1260, 1400, 1680 ] + default: 805 + + qcom,switching-freq: + default: 1600 + + qcom,num-strings: + enum: [ 1, 2, 3 ] + + interrupts: + maxItems: 1 + + interrupt-names: + maxItems: 1 + + else: + properties: + qcom,current-boost-limit: + enum: [ 105, 280, 450, 620, 970, 1150, 1300, 1500 ] + default: 970 + + qcom,switching-freq: + default: 800 + + qcom,num-strings: + enum: [ 1, 2, 3, 4 ] + + interrupts: + minItems: 2 + + interrupt-names: + minItems: 2 + +required: + - compatible + - reg + - label + +additionalProperties: false + +examples: + - | + backlight@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800 0x100>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; + }; From f16899a6a7d4b1a73c7e830c31d83582d678e57c Mon Sep 17 00:00:00 2001 From: Kiran Gunda Date: Thu, 23 Apr 2020 21:03:35 +0530 Subject: [PATCH 4/7] backlight: qcom-wled: Add callback functions Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status and wled_ovp_delay and wled_auto_detection_required callback functions to prepare the driver for adding WLED5 support. Signed-off-by: Kiran Gunda Signed-off-by: Subbaraman Narayanamurthy Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones --- drivers/video/backlight/qcom-wled.c | 213 ++++++++++++++++++---------- 1 file changed, 141 insertions(+), 72 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index 3d276b30a78c..aa18d23dc0e5 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -147,6 +147,7 @@ struct wled { u32 max_brightness; u32 short_count; u32 auto_detect_count; + u32 version; bool disabled_by_short; bool has_short_detect; int short_irq; @@ -154,7 +155,30 @@ struct wled { struct wled_config cfg; struct delayed_work ovp_work; + + /* Configures the brightness. Applicable for wled3, wled4 and wled5 */ int (*wled_set_brightness)(struct wled *wled, u16 brightness); + + /* Configures the cabc register. Applicable for wled4 and wled5 */ + int (*wled_cabc_config)(struct wled *wled, bool enable); + + /* + * Toggles the sync bit for the brightness update to take place. + * Applicable for WLED3, WLED4 and WLED5. + */ + int (*wled_sync_toggle)(struct wled *wled); + + /* + * Time to wait before checking the OVP status after wled module enable. + * Applicable for WLED4 and WLED5. + */ + int (*wled_ovp_delay)(struct wled *wled); + + /* + * Determines if the auto string detection is required. + * Applicable for WLED4 and WLED5 + */ + bool (*wled_auto_detection_required)(struct wled *wled); }; static int wled3_set_brightness(struct wled *wled, u16 brightness) @@ -237,7 +261,7 @@ static int wled_module_enable(struct wled *wled, int val) return 0; } -static int wled_sync_toggle(struct wled *wled) +static int wled3_sync_toggle(struct wled *wled) { int rc; unsigned int mask = GENMASK(wled->max_string_count - 1, 0); @@ -255,6 +279,46 @@ static int wled_sync_toggle(struct wled *wled) return rc; } +static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) +{ + int rc; + u32 int_rt_sts, fault_sts; + + *fault_set = false; + rc = regmap_read(wled->regmap, + wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS, + &int_rt_sts); + if (rc < 0) { + dev_err(wled->dev, "Failed to read INT_RT_STS rc=%d\n", rc); + return rc; + } + + rc = regmap_read(wled->regmap, + wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS, + &fault_sts); + if (rc < 0) { + dev_err(wled->dev, "Failed to read FAULT_STATUS rc=%d\n", rc); + return rc; + } + + if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS) + *fault_set = true; + + if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) + *fault_set = true; + + if (*fault_set) + dev_dbg(wled->dev, "WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n", + int_rt_sts, fault_sts); + + return rc; +} + +static int wled4_ovp_delay(struct wled *wled) +{ + return WLED_SOFT_START_DLY_US; +} + static int wled_update_status(struct backlight_device *bl) { struct wled *wled = bl_get_data(bl); @@ -275,7 +339,7 @@ static int wled_update_status(struct backlight_device *bl) goto unlock_mutex; } - rc = wled_sync_toggle(wled); + rc = wled->wled_sync_toggle(wled); if (rc < 0) { dev_err(wled->dev, "wled sync failed rc:%d\n", rc); goto unlock_mutex; @@ -298,6 +362,25 @@ static int wled_update_status(struct backlight_device *bl) return rc; } +static int wled4_cabc_config(struct wled *wled, bool enable) +{ + int i, j, rc; + u8 val; + + for (i = 0; i < wled->cfg.num_strings; i++) { + j = wled->cfg.enabled_strings[i]; + + val = enable ? WLED4_SINK_REG_STR_CABC_MASK : 0; + rc = regmap_update_bits(wled->regmap, wled->sink_addr + + WLED4_SINK_REG_STR_CABC(j), + WLED4_SINK_REG_STR_CABC_MASK, val); + if (rc < 0) + return rc; + } + + return 0; +} + #define WLED_SHORT_DLY_MS 20 #define WLED_SHORT_CNT_MAX 5 #define WLED_SHORT_RESET_CNT_DLY_US USEC_PER_SEC @@ -345,9 +428,10 @@ static irqreturn_t wled_short_irq_handler(int irq, void *_wled) static void wled_auto_string_detection(struct wled *wled) { - int rc = 0, i; - u32 sink_config = 0, int_sts; + int rc = 0, i, delay_time_us; + u32 sink_config = 0; u8 sink_test = 0, sink_valid = 0, val; + bool fault_set; /* Read configured sink configuration */ rc = regmap_read(wled->regmap, wled->sink_addr + @@ -376,14 +460,9 @@ static void wled_auto_string_detection(struct wled *wled) } if (wled->cfg.cabc) { - for (i = 0; i < wled->cfg.num_strings; i++) { - rc = regmap_update_bits(wled->regmap, wled->sink_addr + - WLED4_SINK_REG_STR_CABC(i), - WLED4_SINK_REG_STR_CABC_MASK, - 0); - if (rc < 0) - goto failed_detect; - } + rc = wled->wled_cabc_config(wled, false); + if (rc < 0) + goto failed_detect; } /* Disable all sinks */ @@ -427,18 +506,17 @@ static void wled_auto_string_detection(struct wled *wled) goto failed_detect; } - usleep_range(WLED_SOFT_START_DLY_US, - WLED_SOFT_START_DLY_US + 1000); + delay_time_us = wled->wled_ovp_delay(wled); + usleep_range(delay_time_us, delay_time_us + 1000); - rc = regmap_read(wled->regmap, wled->ctrl_addr + - WLED3_CTRL_REG_INT_RT_STS, &int_sts); + rc = wled_ovp_fault_status(wled, &fault_set); if (rc < 0) { - dev_err(wled->dev, "Error in reading WLED3_CTRL_INT_RT_STS rc=%d\n", + dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n", rc); goto failed_detect; } - if (int_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS) + if (fault_set) dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n", i + 1); else @@ -478,30 +556,30 @@ static void wled_auto_string_detection(struct wled *wled) } /* Enable valid sinks */ - for (i = 0; i < wled->cfg.num_strings; i++) { - if (wled->cfg.cabc) { - rc = regmap_update_bits(wled->regmap, wled->sink_addr + - WLED4_SINK_REG_STR_CABC(i), - WLED4_SINK_REG_STR_CABC_MASK, - WLED4_SINK_REG_STR_CABC_MASK); - if (rc < 0) + if (wled->version == 4) { + for (i = 0; i < wled->cfg.num_strings; i++) { + if (sink_config & + BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i)) + val = WLED4_SINK_REG_STR_MOD_MASK; + else + /* Disable modulator_en for unused sink */ + val = 0; + + rc = regmap_write(wled->regmap, wled->sink_addr + + WLED4_SINK_REG_STR_MOD_EN(i), val); + if (rc < 0) { + dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n", + rc); goto failed_detect; - } - - if (sink_config & BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i)) - val = WLED4_SINK_REG_STR_MOD_MASK; - else - val = 0x0; /* Disable modulator_en for unused sink */ - - rc = regmap_write(wled->regmap, wled->sink_addr + - WLED4_SINK_REG_STR_MOD_EN(i), val); - if (rc < 0) { - dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n", - rc); - goto failed_detect; + } } } + /* Enable CABC */ + rc = wled->wled_cabc_config(wled, true); + if (rc < 0) + goto failed_detect; + /* Restore the feedback setting */ rc = regmap_write(wled->regmap, wled->ctrl_addr + WLED3_CTRL_REG_FEEDBACK_CONTROL, 0); @@ -534,7 +612,8 @@ static void wled_auto_string_detection(struct wled *wled) #define WLED_AUTO_DETECT_OVP_COUNT 5 #define WLED_AUTO_DETECT_CNT_DLY_US USEC_PER_SEC -static bool wled_auto_detection_required(struct wled *wled) + +static bool wled4_auto_detection_required(struct wled *wled) { s64 elapsed_time_us; @@ -570,29 +649,19 @@ static bool wled_auto_detection_required(struct wled *wled) static int wled_auto_detection_at_init(struct wled *wled) { int rc; - u32 fault_status, rt_status; + bool fault_set; if (!wled->cfg.auto_detection_enabled) return 0; - rc = regmap_read(wled->regmap, - wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS, - &rt_status); + rc = wled_ovp_fault_status(wled, &fault_set); if (rc < 0) { - dev_err(wled->dev, "Failed to read RT status rc=%d\n", rc); + dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n", + rc); return rc; } - rc = regmap_read(wled->regmap, - wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS, - &fault_status); - if (rc < 0) { - dev_err(wled->dev, "Failed to read fault status rc=%d\n", rc); - return rc; - } - - if ((rt_status & WLED3_CTRL_REG_OVP_FAULT_STATUS) || - (fault_status & WLED3_CTRL_REG_OVP_FAULT_BIT)) { + if (fault_set) { mutex_lock(&wled->lock); wled_auto_string_detection(wled); mutex_unlock(&wled->lock); @@ -629,7 +698,7 @@ static irqreturn_t wled_ovp_irq_handler(int irq, void *_wled) int_sts, fault_sts); if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) { - if (wled_auto_detection_required(wled)) { + if (wled->wled_auto_detection_required(wled)) { mutex_lock(&wled->lock); wled_auto_string_detection(wled); mutex_unlock(&wled->lock); @@ -811,17 +880,12 @@ static int wled4_setup(struct wled *wled) wled->cfg.string_i_limit); if (rc < 0) return rc; - - addr = wled->sink_addr + - WLED4_SINK_REG_STR_CABC(j); - rc = regmap_update_bits(wled->regmap, addr, - WLED4_SINK_REG_STR_CABC_MASK, - wled->cfg.cabc ? - WLED4_SINK_REG_STR_CABC_MASK : 0); - if (rc < 0) - return rc; } + rc = wled4_cabc_config(wled, wled->cfg.cabc); + if (rc < 0) + return rc; + rc = regmap_update_bits(wled->regmap, wled->ctrl_addr + WLED3_CTRL_REG_MOD_EN, WLED3_CTRL_REG_MOD_EN_MASK, @@ -835,7 +899,7 @@ static int wled4_setup(struct wled *wled) if (rc < 0) return rc; - rc = wled_sync_toggle(wled); + rc = wled->wled_sync_toggle(wled); if (rc < 0) { dev_err(wled->dev, "Failed to toggle sync reg rc:%d\n", rc); return rc; @@ -951,7 +1015,7 @@ static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx) return idx; } -static int wled_configure(struct wled *wled, int version) +static int wled_configure(struct wled *wled) { struct wled_config *cfg = &wled->cfg; struct device *dev = wled->dev; @@ -1035,12 +1099,13 @@ static int wled_configure(struct wled *wled, int version) if (rc) wled->name = devm_kasprintf(dev, GFP_KERNEL, "%pOFn", dev->of_node); - switch (version) { + switch (wled->version) { case 3: u32_opts = wled3_opts; size = ARRAY_SIZE(wled3_opts); *cfg = wled3_config_defaults; wled->wled_set_brightness = wled3_set_brightness; + wled->wled_sync_toggle = wled3_sync_toggle; wled->max_string_count = 3; wled->sink_addr = wled->ctrl_addr; break; @@ -1050,6 +1115,11 @@ static int wled_configure(struct wled *wled, int version) size = ARRAY_SIZE(wled4_opts); *cfg = wled4_config_defaults; wled->wled_set_brightness = wled4_set_brightness; + wled->wled_sync_toggle = wled3_sync_toggle; + wled->wled_cabc_config = wled4_cabc_config; + wled->wled_ovp_delay = wled4_ovp_delay; + wled->wled_auto_detection_required = + wled4_auto_detection_required; wled->max_string_count = 4; prop_addr = of_get_address(dev->of_node, 1, NULL, NULL); @@ -1186,7 +1256,6 @@ static int wled_probe(struct platform_device *pdev) struct backlight_device *bl; struct wled *wled; struct regmap *regmap; - int version; u32 val; int rc; @@ -1203,18 +1272,18 @@ static int wled_probe(struct platform_device *pdev) wled->regmap = regmap; wled->dev = &pdev->dev; - version = (uintptr_t)of_device_get_match_data(&pdev->dev); - if (!version) { + wled->version = (uintptr_t)of_device_get_match_data(&pdev->dev); + if (!wled->version) { dev_err(&pdev->dev, "Unknown device version\n"); return -ENODEV; } mutex_init(&wled->lock); - rc = wled_configure(wled, version); + rc = wled_configure(wled); if (rc) return rc; - switch (version) { + switch (wled->version) { case 3: wled->cfg.auto_detection_enabled = false; rc = wled3_setup(wled); From b85083d162cf7b67aae06c641cb1128164e73d11 Mon Sep 17 00:00:00 2001 From: Kiran Gunda Date: Thu, 23 Apr 2020 21:03:36 +0530 Subject: [PATCH 5/7] dt-bindings: backlight: qcom-wled: Add WLED5 bindings Add WLED5 specific bindings. Signed-off-by: Kiran Gunda Signed-off-by: Subbaraman Narayanamurthy Acked-by: Daniel Thompson Reviewed-by: Rob Herring Signed-off-by: Lee Jones --- .../bindings/leds/backlight/qcom-wled.yaml | 59 ++++++++++++++++++- 1 file changed, 56 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml index b835443b3c2c..01c7d93dc658 100644 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml @@ -21,6 +21,7 @@ properties: - qcom,pm8941-wled - qcom,pmi8998-wled - qcom,pm660l-wled + - qcom,pm8150l-wled reg: maxItems: 1 @@ -28,12 +29,13 @@ properties: default-brightness: description: | brightness value on boot. - minimum: 0 - maximum: 4095 - default: 2048 label: true + max-brightness: + description: | + Maximum brightness level. + qcom,cs-out: description: | enable current sink output. @@ -141,6 +143,31 @@ properties: - const: ovp - const: short + qcom,modulator-sel: + description: | + Selects the modulator used for brightness modulation. + Allowed values are, + 0 - Modulator A + 1 - Modulator B + This property is applicable only to WLED5 peripheral. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + - default: 0 + + qcom,cabc-sel: + description: | + Selects the CABC pin signal used for brightness modulation. + Allowed values are, + 0 - CABC disabled + 1 - CABC 1 + 2 - CABC 2 + 3 - External signal (e.g. LPG) is used for dimming + This property is applicable only to WLED5 peripheral. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1, 2, 3 ] + allOf: - if: properties: @@ -183,6 +210,32 @@ allOf: interrupt-names: minItems: 2 + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8150l-wled + + then: + properties: + default-brightness: + minimum: 0 + maximum: 32767 + + max-brightness: + minimum: 0 + maximum: 32767 + + else: + properties: + default-brightness: + minimum: 0 + maximum: 4095 + + max-brightness: + minimum: 0 + maximum: 4095 required: - compatible From 62a1d3f623ac0338912fdfbdda9bdac4cadcbc75 Mon Sep 17 00:00:00 2001 From: Subbaraman Narayanamurthy Date: Thu, 23 Apr 2020 21:03:37 +0530 Subject: [PATCH 6/7] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMICs PM8150L WLED supports the following: - Two modulators and each sink can use any of the modulator - Multiple CABC selection options from which one can be selected/enabled - Multiple brightness width selection (12 bits to 15 bits) Signed-off-by: Subbaraman Narayanamurthy Signed-off-by: Kiran Gunda Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones --- drivers/video/backlight/qcom-wled.c | 378 +++++++++++++++++++++++++++- 1 file changed, 376 insertions(+), 2 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index aa18d23dc0e5..4c8c34b99441 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -15,16 +15,21 @@ /* From DT binding */ #define WLED_MAX_STRINGS 4 +#define MOD_A 0 +#define MOD_B 1 #define WLED_DEFAULT_BRIGHTNESS 2048 #define WLED_SOFT_START_DLY_US 10000 #define WLED3_SINK_REG_BRIGHT_MAX 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_12B 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_15B 0x7FFF /* WLED3/WLED4 control registers */ #define WLED3_CTRL_REG_FAULT_STATUS 0x08 #define WLED3_CTRL_REG_ILIM_FAULT_BIT BIT(0) #define WLED3_CTRL_REG_OVP_FAULT_BIT BIT(1) #define WLED4_CTRL_REG_SC_FAULT_BIT BIT(2) +#define WLED5_CTRL_REG_OVP_PRE_ALARM_BIT BIT(4) #define WLED3_CTRL_REG_INT_RT_STS 0x10 #define WLED3_CTRL_REG_OVP_FAULT_STATUS BIT(1) @@ -40,6 +45,7 @@ #define WLED3_CTRL_REG_OVP 0x4d #define WLED3_CTRL_REG_OVP_MASK GENMASK(1, 0) +#define WLED5_CTRL_REG_OVP_MASK GENMASK(3, 0) #define WLED3_CTRL_REG_ILIMIT 0x4e #define WLED3_CTRL_REG_ILIMIT_MASK GENMASK(2, 0) @@ -101,6 +107,44 @@ #define WLED4_SINK_REG_BRIGHT(n) (0x57 + (n * 0x10)) +/* WLED5 specific control registers */ +#define WLED5_CTRL_REG_OVP_INT_CTL 0x5f +#define WLED5_CTRL_REG_OVP_INT_TIMER_MASK GENMASK(2, 0) + +/* WLED5 specific sink registers */ +#define WLED5_SINK_REG_MOD_A_EN 0x50 +#define WLED5_SINK_REG_MOD_B_EN 0x60 +#define WLED5_SINK_REG_MOD_EN_MASK BIT(7) + +#define WLED5_SINK_REG_MOD_A_SRC_SEL 0x51 +#define WLED5_SINK_REG_MOD_B_SRC_SEL 0x61 +#define WLED5_SINK_REG_MOD_SRC_SEL_HIGH 0 +#define WLED5_SINK_REG_MOD_SRC_SEL_EXT 0x03 +#define WLED5_SINK_REG_MOD_SRC_SEL_MASK GENMASK(1, 0) + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL 0x52 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL 0x62 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B 0 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B 1 + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB 0x53 +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB 0x54 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB 0x63 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB 0x64 + +#define WLED5_SINK_REG_MOD_SYNC_BIT 0x65 +#define WLED5_SINK_REG_SYNC_MOD_A_BIT BIT(0) +#define WLED5_SINK_REG_SYNC_MOD_B_BIT BIT(1) +#define WLED5_SINK_REG_SYNC_MASK GENMASK(1, 0) + +/* WLED5 specific per-'string' registers below */ +#define WLED5_SINK_REG_STR_FULL_SCALE_CURR(n) (0x72 + (n * 0x10)) + +#define WLED5_SINK_REG_STR_SRC_SEL(n) (0x73 + (n * 0x10)) +#define WLED5_SINK_REG_SRC_SEL_MOD_A 0 +#define WLED5_SINK_REG_SRC_SEL_MOD_B 1 +#define WLED5_SINK_REG_SRC_SEL_MASK GENMASK(1, 0) + struct wled_var_cfg { const u32 *values; u32 (*fn)(u32); @@ -125,6 +169,8 @@ struct wled_config { u32 num_strings; u32 string_i_limit; u32 enabled_strings[WLED_MAX_STRINGS]; + u32 mod_sel; + u32 cabc_sel; bool cs_out_en; bool ext_gen; bool cabc; @@ -150,6 +196,7 @@ struct wled { u32 version; bool disabled_by_short; bool has_short_detect; + bool cabc_disabled; int short_irq; int ovp_irq; @@ -222,6 +269,28 @@ static int wled4_set_brightness(struct wled *wled, u16 brightness) return 0; } +static int wled5_set_brightness(struct wled *wled, u16 brightness) +{ + int rc, offset; + u16 low_limit = wled->max_brightness * 1 / 1000; + u8 v[2]; + + /* WLED5's lower limit is 0.1% */ + if (brightness < low_limit) + brightness = low_limit; + + v[0] = brightness & 0xff; + v[1] = (brightness >> 8) & 0x7f; + + offset = (wled->cfg.mod_sel == MOD_A) ? + WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB : + WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB; + + rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset, + v, 2); + return rc; +} + static void wled_ovp_work(struct work_struct *work) { struct wled *wled = container_of(work, @@ -279,6 +348,24 @@ static int wled3_sync_toggle(struct wled *wled) return rc; } +static int wled5_sync_toggle(struct wled *wled) +{ + int rc; + u8 val; + + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : + WLED5_SINK_REG_SYNC_MOD_B_BIT; + rc = regmap_update_bits(wled->regmap, + wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, + WLED5_SINK_REG_SYNC_MASK, val); + if (rc < 0) + return rc; + + return regmap_update_bits(wled->regmap, + wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, + WLED5_SINK_REG_SYNC_MASK, 0); +} + static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) { int rc; @@ -304,7 +391,11 @@ static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS) *fault_set = true; - if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) + if (wled->version == 4 && (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT)) + *fault_set = true; + + if (wled->version == 5 && (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT | + WLED5_CTRL_REG_OVP_PRE_ALARM_BIT))) *fault_set = true; if (*fault_set) @@ -319,6 +410,26 @@ static int wled4_ovp_delay(struct wled *wled) return WLED_SOFT_START_DLY_US; } +static int wled5_ovp_delay(struct wled *wled) +{ + int rc, delay_us; + u32 val; + u8 ovp_timer_ms[8] = {1, 2, 4, 8, 12, 16, 20, 24}; + + /* For WLED5, get the delay based on OVP timer */ + rc = regmap_read(wled->regmap, wled->ctrl_addr + + WLED5_CTRL_REG_OVP_INT_CTL, &val); + if (rc < 0) + delay_us = + ovp_timer_ms[val & WLED5_CTRL_REG_OVP_INT_TIMER_MASK] * 1000; + else + delay_us = 2 * WLED_SOFT_START_DLY_US; + + dev_dbg(wled->dev, "delay_time_us: %d\n", delay_us); + + return delay_us; +} + static int wled_update_status(struct backlight_device *bl) { struct wled *wled = bl_get_data(bl); @@ -381,6 +492,31 @@ static int wled4_cabc_config(struct wled *wled, bool enable) return 0; } +static int wled5_cabc_config(struct wled *wled, bool enable) +{ + int rc, offset; + u8 reg; + + if (wled->cabc_disabled) + return 0; + + reg = enable ? wled->cfg.cabc_sel : 0; + offset = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_A_SRC_SEL : + WLED5_SINK_REG_MOD_B_SRC_SEL; + + rc = regmap_update_bits(wled->regmap, wled->sink_addr + offset, + WLED5_SINK_REG_MOD_SRC_SEL_MASK, reg); + if (rc < 0) { + pr_err("Error in configuring CABC rc=%d\n", rc); + return rc; + } + + if (!wled->cfg.cabc_sel) + wled->cabc_disabled = true; + + return 0; +} + #define WLED_SHORT_DLY_MS 20 #define WLED_SHORT_CNT_MAX 5 #define WLED_SHORT_RESET_CNT_DLY_US USEC_PER_SEC @@ -646,6 +782,23 @@ static bool wled4_auto_detection_required(struct wled *wled) return false; } +static bool wled5_auto_detection_required(struct wled *wled) +{ + if (!wled->cfg.auto_detection_enabled) + return false; + + /* + * Unlike WLED4, WLED5 has OVP fault density interrupt configuration + * i.e. to count the number of OVP alarms for a certain duration before + * triggering OVP fault interrupt. By default, number of OVP fault + * events counted before an interrupt is fired is 32 and the time + * interval is 12 ms. If we see one OVP fault interrupt, then that + * should qualify for a real OVP fault condition to run auto detection + * algorithm. + */ + return true; +} + static int wled_auto_detection_at_init(struct wled *wled) { int rc; @@ -921,6 +1074,119 @@ static const struct wled_config wled4_config_defaults = { .auto_detection_enabled = false, }; +static int wled5_setup(struct wled *wled) +{ + int rc, temp, i, j, offset; + u8 sink_en = 0; + u16 addr; + u32 val; + + rc = regmap_update_bits(wled->regmap, + wled->ctrl_addr + WLED3_CTRL_REG_OVP, + WLED5_CTRL_REG_OVP_MASK, wled->cfg.ovp); + if (rc < 0) + return rc; + + rc = regmap_update_bits(wled->regmap, + wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT, + WLED3_CTRL_REG_ILIMIT_MASK, + wled->cfg.boost_i_limit); + if (rc < 0) + return rc; + + rc = regmap_update_bits(wled->regmap, + wled->ctrl_addr + WLED3_CTRL_REG_FREQ, + WLED3_CTRL_REG_FREQ_MASK, + wled->cfg.switch_freq); + if (rc < 0) + return rc; + + /* Per sink/string configuration */ + for (i = 0; i < wled->cfg.num_strings; ++i) { + j = wled->cfg.enabled_strings[i]; + addr = wled->sink_addr + + WLED4_SINK_REG_STR_FULL_SCALE_CURR(j); + rc = regmap_update_bits(wled->regmap, addr, + WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK, + wled->cfg.string_i_limit); + if (rc < 0) + return rc; + + addr = wled->sink_addr + WLED5_SINK_REG_STR_SRC_SEL(j); + rc = regmap_update_bits(wled->regmap, addr, + WLED5_SINK_REG_SRC_SEL_MASK, + wled->cfg.mod_sel == MOD_A ? + WLED5_SINK_REG_SRC_SEL_MOD_A : + WLED5_SINK_REG_SRC_SEL_MOD_B); + + temp = j + WLED4_SINK_REG_CURR_SINK_SHFT; + sink_en |= 1 << temp; + } + + rc = wled5_cabc_config(wled, wled->cfg.cabc_sel ? true : false); + if (rc < 0) + return rc; + + /* Enable one of the modulators A or B based on mod_sel */ + addr = wled->sink_addr + WLED5_SINK_REG_MOD_A_EN; + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_EN_MASK : 0; + rc = regmap_update_bits(wled->regmap, addr, + WLED5_SINK_REG_MOD_EN_MASK, val); + if (rc < 0) + return rc; + + addr = wled->sink_addr + WLED5_SINK_REG_MOD_B_EN; + val = (wled->cfg.mod_sel == MOD_B) ? WLED5_SINK_REG_MOD_EN_MASK : 0; + rc = regmap_update_bits(wled->regmap, addr, + WLED5_SINK_REG_MOD_EN_MASK, val); + if (rc < 0) + return rc; + + offset = (wled->cfg.mod_sel == MOD_A) ? + WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL : + WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL; + + addr = wled->sink_addr + offset; + val = (wled->max_brightness == WLED5_SINK_REG_BRIGHT_MAX_15B) ? + WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B : + WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B; + rc = regmap_write(wled->regmap, addr, val); + if (rc < 0) + return rc; + + rc = regmap_update_bits(wled->regmap, + wled->sink_addr + WLED4_SINK_REG_CURR_SINK, + WLED4_SINK_REG_CURR_SINK_MASK, sink_en); + if (rc < 0) + return rc; + + /* This updates only FSC configuration in WLED5 */ + rc = wled->wled_sync_toggle(wled); + if (rc < 0) { + pr_err("Failed to toggle sync reg rc:%d\n", rc); + return rc; + } + + rc = wled_auto_detection_at_init(wled); + if (rc < 0) + return rc; + + return 0; +} + +static const struct wled_config wled5_config_defaults = { + .boost_i_limit = 5, + .string_i_limit = 10, + .ovp = 4, + .num_strings = 4, + .switch_freq = 11, + .mod_sel = 0, + .cabc_sel = 0, + .cabc = false, + .external_pfet = false, + .auto_detection_enabled = false, +}; + static const u32 wled3_boost_i_limit_values[] = { 105, 385, 525, 805, 980, 1260, 1400, 1680, }; @@ -939,6 +1205,16 @@ static const struct wled_var_cfg wled4_boost_i_limit_cfg = { .size = ARRAY_SIZE(wled4_boost_i_limit_values), }; +static inline u32 wled5_boost_i_limit_values_fn(u32 idx) +{ + return 525 + (idx * 175); +} + +static const struct wled_var_cfg wled5_boost_i_limit_cfg = { + .fn = wled5_boost_i_limit_values_fn, + .size = 8, +}; + static const u32 wled3_ovp_values[] = { 35, 32, 29, 27, }; @@ -957,6 +1233,21 @@ static const struct wled_var_cfg wled4_ovp_cfg = { .size = ARRAY_SIZE(wled4_ovp_values), }; +static inline u32 wled5_ovp_values_fn(u32 idx) +{ + /* + * 0000 - 38.5 V + * 0001 - 37 V .. + * 1111 - 16 V + */ + return 38500 - (idx * 1500); +} + +static const struct wled_var_cfg wled5_ovp_cfg = { + .fn = wled5_ovp_values_fn, + .size = 16, +}; + static u32 wled3_num_strings_values_fn(u32 idx) { return idx + 1; @@ -1004,6 +1295,14 @@ static const struct wled_var_cfg wled4_string_cfg = { .size = 16, }; +static const struct wled_var_cfg wled5_mod_sel_cfg = { + .size = 2, +}; + +static const struct wled_var_cfg wled5_cabc_sel_cfg = { + .size = 4, +}; + static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx) { if (idx >= cfg->size) @@ -1080,6 +1379,44 @@ static int wled_configure(struct wled *wled) }, }; + const struct wled_u32_opts wled5_opts[] = { + { + .name = "qcom,current-boost-limit", + .val_ptr = &cfg->boost_i_limit, + .cfg = &wled5_boost_i_limit_cfg, + }, + { + .name = "qcom,current-limit-microamp", + .val_ptr = &cfg->string_i_limit, + .cfg = &wled4_string_i_limit_cfg, + }, + { + .name = "qcom,ovp-millivolt", + .val_ptr = &cfg->ovp, + .cfg = &wled5_ovp_cfg, + }, + { + .name = "qcom,switching-freq", + .val_ptr = &cfg->switch_freq, + .cfg = &wled3_switch_freq_cfg, + }, + { + .name = "qcom,num-strings", + .val_ptr = &cfg->num_strings, + .cfg = &wled4_num_strings_cfg, + }, + { + .name = "qcom,modulator-sel", + .val_ptr = &cfg->mod_sel, + .cfg = &wled5_mod_sel_cfg, + }, + { + .name = "qcom,cabc-sel", + .val_ptr = &cfg->cabc_sel, + .cfg = &wled5_cabc_sel_cfg, + }, + }; + const struct wled_bool_opts bool_opts[] = { { "qcom,cs-out", &cfg->cs_out_en, }, { "qcom,ext-gen", &cfg->ext_gen, }, @@ -1130,6 +1467,26 @@ static int wled_configure(struct wled *wled) wled->sink_addr = be32_to_cpu(*prop_addr); break; + case 5: + u32_opts = wled5_opts; + size = ARRAY_SIZE(wled5_opts); + *cfg = wled5_config_defaults; + wled->wled_set_brightness = wled5_set_brightness; + wled->wled_sync_toggle = wled5_sync_toggle; + wled->wled_cabc_config = wled5_cabc_config; + wled->wled_ovp_delay = wled5_ovp_delay; + wled->wled_auto_detection_required = + wled5_auto_detection_required; + wled->max_string_count = 4; + + prop_addr = of_get_address(dev->of_node, 1, NULL, NULL); + if (!prop_addr) { + dev_err(wled->dev, "invalid IO resources\n"); + return -EINVAL; + } + wled->sink_addr = be32_to_cpu(*prop_addr); + break; + default: dev_err(wled->dev, "Invalid WLED version\n"); return -EINVAL; @@ -1283,6 +1640,10 @@ static int wled_probe(struct platform_device *pdev) if (rc) return rc; + val = WLED3_SINK_REG_BRIGHT_MAX; + of_property_read_u32(pdev->dev.of_node, "max-brightness", &val); + wled->max_brightness = val; + switch (wled->version) { case 3: wled->cfg.auto_detection_enabled = false; @@ -1302,6 +1663,18 @@ static int wled_probe(struct platform_device *pdev) } break; + case 5: + wled->has_short_detect = true; + if (wled->cfg.cabc_sel) + wled->max_brightness = WLED5_SINK_REG_BRIGHT_MAX_12B; + + rc = wled5_setup(wled); + if (rc) { + dev_err(&pdev->dev, "wled5_setup failed\n"); + return rc; + } + break; + default: dev_err(wled->dev, "Invalid WLED version\n"); break; @@ -1323,7 +1696,7 @@ static int wled_probe(struct platform_device *pdev) memset(&props, 0, sizeof(struct backlight_properties)); props.type = BACKLIGHT_RAW; props.brightness = val; - props.max_brightness = WLED3_SINK_REG_BRIGHT_MAX; + props.max_brightness = wled->max_brightness; bl = devm_backlight_device_register(&pdev->dev, wled->name, &pdev->dev, wled, &wled_ops, &props); @@ -1346,6 +1719,7 @@ static const struct of_device_id wled_match_table[] = { { .compatible = "qcom,pm8941-wled", .data = (void *)3 }, { .compatible = "qcom,pmi8998-wled", .data = (void *)4 }, { .compatible = "qcom,pm660l-wled", .data = (void *)4 }, + { .compatible = "qcom,pm8150l-wled", .data = (void *)5 }, {} }; MODULE_DEVICE_TABLE(of, wled_match_table); From 479da1f538a2f3547e15f9d5922c611b69ec2fbc Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= Date: Sat, 9 May 2020 16:16:10 +0200 Subject: [PATCH 7/7] backlight: Add backlight_device_get_by_name() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add a way to lookup a backlight device based on its name. Will be used by a USB display gadget getting the name from configfs. Signed-off-by: Noralf Trønnes Reviewed-by: Sam Ravnborg Reviewed-by: Daniel Thompson Acked-by: Jingoo Han Signed-off-by: Lee Jones --- drivers/video/backlight/backlight.c | 21 +++++++++++++++++++++ include/linux/backlight.h | 1 + 2 files changed, 22 insertions(+) diff --git a/drivers/video/backlight/backlight.c b/drivers/video/backlight/backlight.c index cac3e35d7630..92d80aa0c0ef 100644 --- a/drivers/video/backlight/backlight.c +++ b/drivers/video/backlight/backlight.c @@ -432,6 +432,27 @@ struct backlight_device *backlight_device_get_by_type(enum backlight_type type) } EXPORT_SYMBOL(backlight_device_get_by_type); +/** + * backlight_device_get_by_name - Get backlight device by name + * @name: Device name + * + * This function looks up a backlight device by its name. It obtains a reference + * on the backlight device and it is the caller's responsibility to drop the + * reference by calling backlight_put(). + * + * Returns: + * A pointer to the backlight device if found, otherwise NULL. + */ +struct backlight_device *backlight_device_get_by_name(const char *name) +{ + struct device *dev; + + dev = class_find_device_by_name(backlight_class, name); + + return dev ? to_backlight_device(dev) : NULL; +} +EXPORT_SYMBOL(backlight_device_get_by_name); + /** * backlight_device_unregister - unregisters a backlight device object. * @bd: the backlight device object to be unregistered and freed. diff --git a/include/linux/backlight.h b/include/linux/backlight.h index c7d6b2e8c3b5..56e4580d4f55 100644 --- a/include/linux/backlight.h +++ b/include/linux/backlight.h @@ -190,6 +190,7 @@ extern void backlight_force_update(struct backlight_device *bd, extern int backlight_register_notifier(struct notifier_block *nb); extern int backlight_unregister_notifier(struct notifier_block *nb); extern struct backlight_device *backlight_device_get_by_type(enum backlight_type type); +struct backlight_device *backlight_device_get_by_name(const char *name); extern int backlight_device_set_brightness(struct backlight_device *bd, unsigned long brightness); #define to_backlight_device(obj) container_of(obj, struct backlight_device, dev)