AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity

Merge branch 'sti/dt' into next/drivers

Browse Source 
This is apparently a dependency for the STi reset controller driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit is contained in:
Arnd Bergmann 2014-03-18 16:19:44 +01:00
commit 4569f2b7be
12 changed files with 770 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

47
Documentation/devicetree/bindings/reset/st,sti-powerdown.txt Normal file
View File

@ -0,0 +1,47 @@
STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
=============================================================================
This binding describes a reset controller device that is used to enable and
disable on-chip peripheral controllers such as USB and SATA, using
"powerdown" control bits found in the STi family SoC system configuration
registers. These have been grouped together into a single reset controller
device for convenience.
The actual action taken when powerdown is asserted is hardware dependent.
However, when asserted it may not be possible to access the hardware's
registers and after an assert/deassert sequence the hardware's previous state
may no longer be valid.
Please refer to reset.txt in this directory for common reset
controller binding usage.
Required properties:
- compatible: Should be "st,<chip>-powerdown"
ex: "st,stih415-powerdown", "st,stih416-powerdown"
- #reset-cells: 1, see below
example:
powerdown: powerdown-controller {
#reset-cells = <1>;
compatible = "st,stih415-powerdown";
};
Specifying powerdown control of devices
=======================================
Device nodes should specify the reset channel required in their "resets"
property, containing a phandle to the powerdown device node and an
index specifying which channel to use, as described in reset.txt
example:
usb1: usb@fe200000 {
resets = <&powerdown STIH41X_USB1_POWERDOWN>;
};
Macro definitions for the supported reset channels can be found in:
include/dt-bindings/reset-controller/stih415-resets.h
include/dt-bindings/reset-controller/stih416-resets.h

46
Documentation/devicetree/bindings/reset/st,sti-softreset.txt Normal file
View File

@ -0,0 +1,46 @@
STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
=============================================================================
This binding describes a reset controller device that is used to enable and
disable on-chip peripheral controllers such as USB and SATA, using
"softreset" control bits found in the STi family SoC system configuration
registers.
The actual action taken when softreset is asserted is hardware dependent.
However, when asserted it may not be possible to access the hardware's
registers and after an assert/deassert sequence the hardware's previous state
may no longer be valid.
Please refer to reset.txt in this directory for common reset
controller binding usage.
Required properties:
- compatible: Should be "st,<chip>-softreset" example:
"st,stih415-softreset" or "st,stih416-softreset";
- #reset-cells: 1, see below
example:
softreset: softreset-controller {
#reset-cells = <1>;
compatible = "st,stih415-softreset";
};
Specifying softreset control of devices
=======================================
Device nodes should specify the reset channel required in their "resets"
property, containing a phandle to the softreset device node and an
index specifying which channel to use, as described in reset.txt
example:
ethernet0{
resets = <&softreset STIH415_ETH0_SOFTRESET>;
};
Macro definitions for the supported reset channels can be found in:
include/dt-bindings/reset-controller/stih415-resets.h
include/dt-bindings/reset-controller/stih416-resets.h

14
arch/arm/boot/dts/stih415-clock.dtsi
View File

@ -34,5 +34,19 @@ CLKS_ICN_REG_0: CLKS_ICN_REG_0 {
compatible = "fixed-clock";
clock-frequency = <100000000>;
};
CLKS_GMAC0_PHY: clockgenA1@7 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "CLKS_GMAC0_PHY";
};
CLKS_ETH1_PHY: clockgenA0@7 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "CLKS_ETH1_PHY";
};
};
};

204
arch/arm/boot/dts/stih415-pinctrl.dtsi
View File

@ -7,6 +7,7 @@
* publishhed by the Free Software Foundation.
*/
#include "st-pincfg.h"
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
aliases {
@ -45,35 +46,49 @@ pin-controller-sbc {
#size-cells = <1>;
compatible = "st,stih415-sbc-pinctrl";
st,syscfg = <&syscfg_sbc>;
reg = <0xfe61f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x5000>;
PIO0: gpio@fe610000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO0";
};
PIO1: gpio@fe611000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
PIO2: gpio@fe612000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
PIO3: gpio@fe613000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
PIO4: gpio@fe614000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO4";
};
@ -104,6 +119,64 @@ st,pins {
};
};
};
rc{
pinctrl_ir: ir0 {
st,pins {
ir = <&PIO4 0 ALT2 IN>;
};
};
};
gmac1 {
pinctrl_mii1: mii1 {
st,pins {
txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
col = <&PIO0 7 ALT1 IN BYPASS 1000>;
mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
};
};
pinctrl_rgmii1: rgmii1-0 {
st,pins {
txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
};
};
};
};
pin-controller-front {
@ -111,53 +184,73 @@ pin-controller-front {
#size-cells = <1>;
compatible = "st,stih415-front-pinctrl";
st,syscfg = <&syscfg_front>;
reg = <0xfee0f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x8000>;
PIO5: gpio@fee00000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO5";
};
PIO6: gpio@fee01000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
PIO7: gpio@fee02000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
PIO8: gpio@fee03000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
PIO9: gpio@fee04000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
PIO10: gpio@fee05000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
PIO11: gpio@fee06000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
PIO12: gpio@fee07000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
@ -186,41 +279,57 @@ pin-controller-rear {
#size-cells = <1>;
compatible = "st,stih415-rear-pinctrl";
st,syscfg = <&syscfg_rear>;
reg = <0xfe82f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x8000>;
PIO13: gpio@fe820000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO13";
};
PIO14: gpio@fe821000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
PIO15: gpio@fe822000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
PIO16: gpio@fe823000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
PIO17: gpio@fe824000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
PIO18: gpio@fe825000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO18";
};
@ -233,6 +342,77 @@ st,pins {
};
};
};
gmac0{
pinctrl_mii0: mii0 {
st,pins {
mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
col = <&PIO15 3 ALT2 IN BYPASS 1000>;
mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
};
};
pinctrl_gmii0: gmii0 {
st,pins {
mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
col = <&PIO15 3 ALT2 IN BYPASS 1000>;
rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
};
};
};
};
pin-controller-left {
@ -240,23 +420,33 @@ pin-controller-left {
#size-cells = <1>;
compatible = "st,stih415-left-pinctrl";
st,syscfg = <&syscfg_left>;
reg = <0xfd6bf080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
PIO100: gpio@fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO100";
};
PIO101: gpio@fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
PIO102: gpio@fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO102";
};
@ -267,35 +457,49 @@ pin-controller-right {
#size-cells = <1>;
compatible = "st,stih415-right-pinctrl";
st,syscfg = <&syscfg_right>;
reg = <0xfd33f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
PIO103: gpio@fd330000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO103";
};
PIO104: gpio@fd331000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
PIO105: gpio@fd332000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
PIO106: gpio@fd333000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO106";
};
PIO107: gpio@fd334000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO107";
};

70
arch/arm/boot/dts/stih415.dtsi
View File

@ -10,6 +10,7 @@
#include "stih415-clock.dtsi"
#include "stih415-pinctrl.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset-controller/stih415-resets.h>
/ {
L2: cache-controller {
@ -28,6 +29,16 @@ soc {
ranges;
compatible = "simple-bus";
powerdown: powerdown-controller {
#reset-cells = <1>;
compatible = "st,stih415-powerdown";
};
softreset: softreset-controller {
#reset-cells = <1>;
compatible = "st,stih415-softreset";
};
syscfg_sbc: sbc-syscfg@fe600000{
compatible = "st,stih415-sbc-syscfg", "syscon";
reg = <0xfe600000 0xb4>;
@ -136,5 +147,64 @@ i2c@fe541000 {
status = "disabled";
};
ethernet0: dwmac@fe810000 {
device_type = "network";
compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
status = "disabled";
reg = <0xfe810000 0x8000>, <0x148 0x4>;
reg-names = "stmmaceth", "sti-ethconf";
interrupts = <0 147 0>, <0 148 0>, <0 149 0>;
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
resets = <&softreset STIH415_ETH0_SOFTRESET>;
reset-names = "stmmaceth";
snps,pbl = <32>;
snps,mixed-burst;
snps,force_sf_dma_mode;
st,syscon = <&syscfg_rear>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mii0>;
clock-names = "stmmaceth";
clocks = <&CLKS_GMAC0_PHY>;
};
ethernet1: dwmac@fef08000 {
device_type = "network";
compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
status = "disabled";
reg = <0xfef08000 0x8000>, <0x74 0x4>;
reg-names = "stmmaceth", "sti-ethconf";
interrupts = <0 150 0>, <0 151 0>, <0 152 0>;
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
snps,pbl = <32>;
snps,mixed-burst;
snps,force_sf_dma_mode;
st,syscon = <&syscfg_sbc>;
resets = <&softreset STIH415_ETH1_SOFTRESET>;
reset-names = "stmmaceth";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mii1>;
clock-names = "stmmaceth";
clocks = <&CLKS_ETH1_PHY>;
};
rc: rc@fe518000 {
compatible = "st,comms-irb";
reg = <0xfe518000 0x234>;
interrupts = <0 203 0>;
clocks = <&CLK_SYSIN>;
rx-mode = "infrared";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ir>;
resets = <&softreset STIH415_IRB_SOFTRESET>;
};
};
};

14
arch/arm/boot/dts/stih416-clock.dtsi
View File

@ -37,5 +37,19 @@ CLK_S_ICN_REG_0: clockgenA0@4 {
clock-frequency = <100000000>;
clock-output-names = "CLK_S_ICN_REG_0";
};
CLK_S_GMAC0_PHY: clockgenA1@7 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "CLK_S_GMAC0_PHY";
};
CLK_S_ETH1_PHY: clockgenA0@7 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "CLK_S_ETH1_PHY";
};
};
};

197
arch/arm/boot/dts/stih416-pinctrl.dtsi
View File

@ -8,6 +8,7 @@
* publishhed by the Free Software Foundation.
*/
#include "st-pincfg.h"
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
aliases {
@ -49,46 +50,69 @@ pin-controller-sbc {
#size-cells = <1>;
compatible = "st,stih416-sbc-pinctrl";
st,syscfg = <&syscfg_sbc>;
reg = <0xfe61f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x6000>;
PIO0: gpio@fe610000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO0";
};
PIO1: gpio@fe611000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
PIO2: gpio@fe612000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
PIO3: gpio@fe613000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
PIO4: gpio@fe614000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO4";
};
PIO40: gpio@fe615000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO40";
st,retime-pin-mask = <0x7f>;
};
rc{
pinctrl_ir: ir0 {
st,pins {
ir = <&PIO4 0 ALT2 IN>;
};
};
};
sbc_serial1 {
pinctrl_sbc_serial1: sbc_serial1 {
st,pins {
@ -115,6 +139,58 @@ st,pins {
};
};
};
gmac1 {
pinctrl_mii1: mii1 {
st,pins {
txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
col = <&PIO0 7 ALT1 IN BYPASS 1000>;
mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
};
};
pinctrl_rgmii1: rgmii1-0 {
st,pins {
txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
};
};
};
};
pin-controller-front {
@ -122,65 +198,89 @@ pin-controller-front {
#size-cells = <1>;
compatible = "st,stih416-front-pinctrl";
st,syscfg = <&syscfg_front>;
reg = <0xfee0f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x10000>;
PIO5: gpio@fee00000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO5";
};
PIO6: gpio@fee01000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
PIO7: gpio@fee02000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
PIO8: gpio@fee03000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
PIO9: gpio@fee04000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
PIO10: gpio@fee05000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
PIO11: gpio@fee06000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
PIO12: gpio@fee07000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
PIO30: gpio@fee08000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x8000 0x100>;
st,bank-name = "PIO30";
};
PIO31: gpio@fee09000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x9000 0x100>;
st,bank-name = "PIO31";
};
@ -217,41 +317,57 @@ pin-controller-rear {
#size-cells = <1>;
compatible = "st,stih416-rear-pinctrl";
st,syscfg = <&syscfg_rear>;
reg = <0xfe82f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x6000>;
PIO13: gpio@fe820000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO13";
};
PIO14: gpio@fe821000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
PIO15: gpio@fe822000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
PIO16: gpio@fe823000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
PIO17: gpio@fe824000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
PIO18: gpio@fe825000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO18";
st,retime-pin-mask = <0xf>;
@ -265,6 +381,63 @@ st,pins {
};
};
};
gmac0 {
pinctrl_mii0: mii0 {
st,pins {
mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
col = <&PIO15 3 ALT2 IN BYPASS 1000>;
mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
};
};
pinctrl_gmii0: gmii0 {
st,pins {
};
};
pinctrl_rgmii0: rgmii0 {
st,pins {
phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
};
};
};
};
pin-controller-fvdp-fe {
@ -272,23 +445,33 @@ pin-controller-fvdp-fe {
#size-cells = <1>;
compatible = "st,stih416-fvdp-fe-pinctrl";
st,syscfg = <&syscfg_fvdp_fe>;
reg = <0xfd6bf080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
PIO100: gpio@fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO100";
};
PIO101: gpio@fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
PIO102: gpio@fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO102";
};
@ -299,29 +482,41 @@ pin-controller-fvdp-lite {
#size-cells = <1>;
compatible = "st,stih416-fvdp-lite-pinctrl";
st,syscfg = <&syscfg_fvdp_lite>;
reg = <0xfd33f080 0x4>;
reg-names = "irqmux";
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
PIO103: gpio@fd330000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO103";
};
PIO104: gpio@fd331000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
PIO105: gpio@fd332000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
PIO106: gpio@fd333000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO106";
};
@ -329,6 +524,8 @@ PIO106: gpio@fd333000 {
PIO107: gpio@fd334000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO107";
st,retime-pin-mask = <0xf>;

67
arch/arm/boot/dts/stih416.dtsi
View File

@ -10,6 +10,7 @@
#include "stih416-clock.dtsi"
#include "stih416-pinctrl.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset-controller/stih416-resets.h>
/ {
L2: cache-controller {
compatible = "arm,pl310-cache";
@ -27,6 +28,16 @@ soc {
ranges;
compatible = "simple-bus";
powerdown: powerdown-controller {
#reset-cells = <1>;
compatible = "st,stih416-powerdown";
};
softreset: softreset-controller {
#reset-cells = <1>;
compatible = "st,stih416-softreset";
};
syscfg_sbc:sbc-syscfg@fe600000{
compatible = "st,stih416-sbc-syscfg", "syscon";
reg = <0xfe600000 0x1000>;
@ -145,5 +156,61 @@ i2c@fe541000 {
status = "disabled";
};
ethernet0: dwmac@fe810000 {
device_type = "network";
compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
status = "disabled";
reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
reg-names = "stmmaceth", "sti-ethconf";
interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
snps,pbl = <32>;
snps,mixed-burst;
st,syscon = <&syscfg_rear>;
resets = <&softreset STIH416_ETH0_SOFTRESET>;
reset-names = "stmmaceth";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mii0>;
clock-names = "stmmaceth";
clocks = <&CLK_S_GMAC0_PHY>;
};
ethernet1: dwmac@fef08000 {
device_type = "network";
compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
status = "disabled";
reg = <0xfef08000 0x8000>, <0x7f0 0x4>;
reg-names = "stmmaceth", "sti-ethconf";
interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
snps,pbl = <32>;
snps,mixed-burst;
st,syscon = <&syscfg_sbc>;
resets = <&softreset STIH416_ETH1_SOFTRESET>;
reset-names = "stmmaceth";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mii1>;
clock-names = "stmmaceth";
clocks = <&CLK_S_ETH1_PHY>;
};
rc: rc@fe518000 {
compatible = "st,comms-irb";
reg = <0xfe518000 0x234>;
interrupts = <0 203 0>;
rx-mode = "infrared";
clocks = <&CLK_SYSIN>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ir>;
resets = <&softreset STIH416_IRB_SOFTRESET>;
};
};
};

22
arch/arm/boot/dts/stih41x-b2000.dtsi
View File

@ -20,6 +20,8 @@ chosen {
aliases {
ttyAS0 = &serial2;
ethernet0 = &ethernet0;
ethernet1 = &ethernet1;
};
soc {
@ -46,5 +48,25 @@ i2c@fed41000 {
status = "okay";
};
ethernet0: dwmac@fe810000 {
status = "okay";
phy-mode = "mii";
pinctrl-0 = <&pinctrl_mii0>;
snps,reset-gpio = <&PIO106 2>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
};
ethernet1: dwmac@fef08000 {
status = "disabled";
phy-mode = "mii";
st,tx-retime-src = "txclk";
snps,reset-gpio = <&PIO4 7>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
};
};
};

13
arch/arm/boot/dts/stih41x-b2020.dtsi
View File

@ -19,6 +19,7 @@ chosen {
aliases {
ttyAS0 = &sbc_serial1;
ethernet1 = &ethernet1;
};
soc {
sbc_serial1: serial@fe531000 {
@ -60,5 +61,17 @@ i2c@fe540000 {
i2c@fe541000 {
status = "okay";
};
ethernet1: dwmac@fef08000 {
status = "okay";
phy-mode = "rgmii-id";
max-speed = <1000>;
st,tx-retime-src = "clk_125";
snps,reset-gpio = <&PIO3 0>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
pinctrl-0 = <&pinctrl_rgmii1>;
};
};
};

26
include/dt-bindings/reset-controller/stih415-resets.h Normal file
View File

@ -0,0 +1,26 @@
/*
* This header provides constants for the reset controller
* based peripheral powerdown requests on the STMicroelectronics
* STiH415 SoC.
*/
#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415
#define _DT_BINDINGS_RESET_CONTROLLER_STIH415
#define STIH415_EMISS_POWERDOWN 0
#define STIH415_NAND_POWERDOWN 1
#define STIH415_KEYSCAN_POWERDOWN 2
#define STIH415_USB0_POWERDOWN 3
#define STIH415_USB1_POWERDOWN 4
#define STIH415_USB2_POWERDOWN 5
#define STIH415_SATA0_POWERDOWN 6
#define STIH415_SATA1_POWERDOWN 7
#define STIH415_PCIE_POWERDOWN 8
#define STIH415_ETH0_SOFTRESET 0
#define STIH415_ETH1_SOFTRESET 1
#define STIH415_IRB_SOFTRESET 2
#define STIH415_USB0_SOFTRESET 3
#define STIH415_USB1_SOFTRESET 4
#define STIH415_USB2_SOFTRESET 5
#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */

50
include/dt-bindings/reset-controller/stih416-resets.h Normal file
View File

@ -0,0 +1,50 @@
/*
* This header provides constants for the reset controller
* based peripheral powerdown requests on the STMicroelectronics
* STiH416 SoC.
*/
#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH416
#define _DT_BINDINGS_RESET_CONTROLLER_STIH416
#define STIH416_EMISS_POWERDOWN 0
#define STIH416_NAND_POWERDOWN 1
#define STIH416_KEYSCAN_POWERDOWN 2
#define STIH416_USB0_POWERDOWN 3
#define STIH416_USB1_POWERDOWN 4
#define STIH416_USB2_POWERDOWN 5
#define STIH416_USB3_POWERDOWN 6
#define STIH416_SATA0_POWERDOWN 7
#define STIH416_SATA1_POWERDOWN 8
#define STIH416_PCIE0_POWERDOWN 9
#define STIH416_PCIE1_POWERDOWN 10
#define STIH416_ETH0_SOFTRESET 0
#define STIH416_ETH1_SOFTRESET 1
#define STIH416_IRB_SOFTRESET 2
#define STIH416_USB0_SOFTRESET 3
#define STIH416_USB1_SOFTRESET 4
#define STIH416_USB2_SOFTRESET 5
#define STIH416_USB3_SOFTRESET 6
#define STIH416_SATA0_SOFTRESET 7
#define STIH416_SATA1_SOFTRESET 8
#define STIH416_PCIE0_SOFTRESET 9
#define STIH416_PCIE1_SOFTRESET 10
#define STIH416_AUD_DAC_SOFTRESET 11
#define STIH416_HDTVOUT_SOFTRESET 12
#define STIH416_VTAC_M_RX_SOFTRESET 13
#define STIH416_VTAC_A_RX_SOFTRESET 14
#define STIH416_SYNC_HD_SOFTRESET 15
#define STIH416_SYNC_SD_SOFTRESET 16
#define STIH416_BLITTER_SOFTRESET 17
#define STIH416_GPU_SOFTRESET 18
#define STIH416_VTAC_M_TX_SOFTRESET 19
#define STIH416_VTAC_A_TX_SOFTRESET 20
#define STIH416_VTG_AUX_SOFTRESET 21
#define STIH416_JPEG_DEC_SOFTRESET 22
#define STIH416_HVA_SOFTRESET 23
#define STIH416_COMPO_M_SOFTRESET 24
#define STIH416_COMPO_A_SOFTRESET 25
#define STIH416_VP8_DEC_SOFTRESET 26
#define STIH416_VTG_MAIN_SOFTRESET 27
#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH416 */