AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity

ARM: STi: STiH415: Add reset controller support.

Browse Source 
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This commit is contained in:
Srinivas Kandagatla 2014-03-11 09:24:55 +00:00
parent 7ec5183a0a
commit 6b7f06cc80
3 changed files with 72 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

47
Documentation/devicetree/bindings/reset/st,sti-powerdown.txt Normal file
View File

@ -0,0 +1,47 @@
STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
=============================================================================
This binding describes a reset controller device that is used to enable and
disable on-chip peripheral controllers such as USB and SATA, using
"powerdown" control bits found in the STi family SoC system configuration
registers. These have been grouped together into a single reset controller
device for convenience.
The actual action taken when powerdown is asserted is hardware dependent.
However, when asserted it may not be possible to access the hardware's
registers and after an assert/deassert sequence the hardware's previous state
may no longer be valid.
Please refer to reset.txt in this directory for common reset
controller binding usage.
Required properties:
- compatible: Should be "st,<chip>-powerdown"
ex: "st,stih415-powerdown", "st,stih416-powerdown"
- #reset-cells: 1, see below
example:
powerdown: powerdown-controller {
#reset-cells = <1>;
compatible = "st,stih415-powerdown";
};
Specifying powerdown control of devices
=======================================
Device nodes should specify the reset channel required in their "resets"
property, containing a phandle to the powerdown device node and an
index specifying which channel to use, as described in reset.txt
example:
usb1: usb@fe200000 {
resets = <&powerdown STIH41X_USB1_POWERDOWN>;
};
Macro definitions for the supported reset channels can be found in:
include/dt-bindings/reset-controller/stih415-resets.h
include/dt-bindings/reset-controller/stih416-resets.h

6
arch/arm/boot/dts/stih415.dtsi
View File

@ -10,6 +10,7 @@
#include "stih415-clock.dtsi"
#include "stih415-pinctrl.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset-controller/stih415-resets.h>
/ {
L2: cache-controller {
@ -28,6 +29,11 @@ soc {
ranges;
compatible = "simple-bus";
powerdown: powerdown-controller {
#reset-cells = <1>;
compatible = "st,stih415-powerdown";
};
syscfg_sbc: sbc-syscfg@fe600000{
compatible = "st,stih415-sbc-syscfg", "syscon";
reg = <0xfe600000 0xb4>;

19
include/dt-bindings/reset-controller/stih415-resets.h Normal file
View File

@ -0,0 +1,19 @@
/*
* This header provides constants for the reset controller
* based peripheral powerdown requests on the STMicroelectronics
* STiH415 SoC.
*/
#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415
#define _DT_BINDINGS_RESET_CONTROLLER_STIH415
#define STIH415_EMISS_POWERDOWN 0
#define STIH415_NAND_POWERDOWN 1
#define STIH415_KEYSCAN_POWERDOWN 2
#define STIH415_USB0_POWERDOWN 3
#define STIH415_USB1_POWERDOWN 4
#define STIH415_USB2_POWERDOWN 5
#define STIH415_SATA0_POWERDOWN 6
#define STIH415_SATA1_POWERDOWN 7
#define STIH415_PCIE_POWERDOWN 8
#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */