forked from luck/tmp_suning_uos_patched
hwmon: Add support for INA3221 Triple Current/Voltage Monitors
Add support for the the INA3221 26v capable, Triple channel, Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor with I2C interface. Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit is contained in:
Andrew F. Davis
Guenter Roeck
parent
c0a6860180
commit
7cb6dcff19
35
Documentation/hwmon/ina3221
Normal file
35
Documentation/hwmon/ina3221
Normal file
|
|
@ -0,0 +1,35 @@
|
|||
Kernel driver ina3221
|
||||
=====================
|
||||
|
||||
Supported chips:
|
||||
* Texas Instruments INA3221
|
||||
Prefix: 'ina3221'
|
||||
Addresses: I2C 0x40 - 0x43
|
||||
Datasheet: Publicly available at the Texas Instruments website
|
||||
http://www.ti.com/
|
||||
|
||||
Author: Andrew F. Davis <afd@ti.com>
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
The Texas Instruments INA3221 monitors voltage, current, and power on the high
|
||||
side of up to three D.C. power supplies. The INA3221 monitors both shunt drop
|
||||
and supply voltage, with programmable conversion times and averaging, current
|
||||
and power are calculated host-side from these.
|
||||
|
||||
Sysfs entries
|
||||
-------------
|
||||
|
||||
in[123]_input Bus voltage(mV) channels
|
||||
curr[123]_input Current(mA) measurement channels
|
||||
shunt[123]_resistor Shunt resistance(uOhm) channels
|
||||
curr[123]_crit Critical alert current(mA) setting, activates the
|
||||
corresponding alarm when the respective current
|
||||
is above this value
|
||||
curr[123]_crit_alarm Critical alert current limit exceeded
|
||||
curr[123]_max Warning alert current(mA) setting, activates the
|
||||
corresponding alarm when the respective current
|
||||
average is above this value.
|
||||
curr[123]_max_alarm Warning alert current limit exceeded
|
||||
in[456]_input Shunt voltage(uV) for channels 1, 2, and 3 respectively
|
||||
|
|
@ -1525,6 +1525,17 @@ config SENSORS_INA2XX
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called ina2xx.
|
||||
|
||||
config SENSORS_INA3221
|
||||
tristate "Texas Instruments INA3221 Triple Power Monitor"
|
||||
depends on I2C
|
||||
select REGMAP_I2C
|
||||
help
|
||||
If you say yes here you get support for the TI INA3221 Triple Power
|
||||
Monitor.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called ina3221.
|
||||
|
||||
config SENSORS_TC74
|
||||
tristate "Microchip TC74"
|
||||
depends on I2C
|
||||
|
|
|
|||
|
|
@ -77,6 +77,7 @@ obj-$(CONFIG_SENSORS_IBMPOWERNV)+= ibmpowernv.o
|
|||
obj-$(CONFIG_SENSORS_IIO_HWMON) += iio_hwmon.o
|
||||
obj-$(CONFIG_SENSORS_INA209) += ina209.o
|
||||
obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o
|
||||
obj-$(CONFIG_SENSORS_INA3221) += ina3221.o
|
||||
obj-$(CONFIG_SENSORS_IT87) += it87.o
|
||||
obj-$(CONFIG_SENSORS_JC42) += jc42.o
|
||||
obj-$(CONFIG_SENSORS_JZ4740) += jz4740-hwmon.o
|
||||
|
|
|
|||
446
drivers/hwmon/ina3221.c
Normal file
446
drivers/hwmon/ina3221.c
Normal file
|
|
@ -0,0 +1,446 @@
|
|||
/*
|
||||
* INA3221 Triple Current/Voltage Monitor
|
||||
*
|
||||
* Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
|
||||
* Andrew F. Davis <afd@ti.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful, but
|
||||
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
||||
* General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/hwmon.h>
|
||||
#include <linux/hwmon-sysfs.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
#define INA3221_DRIVER_NAME "ina3221"
|
||||
|
||||
#define INA3221_CONFIG 0x00
|
||||
#define INA3221_SHUNT1 0x01
|
||||
#define INA3221_BUS1 0x02
|
||||
#define INA3221_SHUNT2 0x03
|
||||
#define INA3221_BUS2 0x04
|
||||
#define INA3221_SHUNT3 0x05
|
||||
#define INA3221_BUS3 0x06
|
||||
#define INA3221_CRIT1 0x07
|
||||
#define INA3221_WARN1 0x08
|
||||
#define INA3221_CRIT2 0x09
|
||||
#define INA3221_WARN2 0x0a
|
||||
#define INA3221_CRIT3 0x0b
|
||||
#define INA3221_WARN3 0x0c
|
||||
#define INA3221_MASK_ENABLE 0x0f
|
||||
|
||||
#define INA3221_CONFIG_MODE_SHUNT BIT(1)
|
||||
#define INA3221_CONFIG_MODE_BUS BIT(2)
|
||||
#define INA3221_CONFIG_MODE_CONTINUOUS BIT(3)
|
||||
|
||||
#define INA3221_RSHUNT_DEFAULT 10000
|
||||
|
||||
enum ina3221_fields {
|
||||
/* Configuration */
|
||||
F_RST,
|
||||
|
||||
/* Alert Flags */
|
||||
F_WF3, F_WF2, F_WF1,
|
||||
F_CF3, F_CF2, F_CF1,
|
||||
|
||||
/* sentinel */
|
||||
F_MAX_FIELDS
|
||||
};
|
||||
|
||||
static const struct reg_field ina3221_reg_fields[] = {
|
||||
[F_RST] = REG_FIELD(INA3221_CONFIG, 15, 15),
|
||||
|
||||
[F_WF3] = REG_FIELD(INA3221_MASK_ENABLE, 3, 3),
|
||||
[F_WF2] = REG_FIELD(INA3221_MASK_ENABLE, 4, 4),
|
||||
[F_WF1] = REG_FIELD(INA3221_MASK_ENABLE, 5, 5),
|
||||
[F_CF3] = REG_FIELD(INA3221_MASK_ENABLE, 7, 7),
|
||||
[F_CF2] = REG_FIELD(INA3221_MASK_ENABLE, 8, 8),
|
||||
[F_CF1] = REG_FIELD(INA3221_MASK_ENABLE, 9, 9),
|
||||
};
|
||||
|
||||
enum ina3221_channels {
|
||||
INA3221_CHANNEL1,
|
||||
INA3221_CHANNEL2,
|
||||
INA3221_CHANNEL3,
|
||||
INA3221_NUM_CHANNELS
|
||||
};
|
||||
|
||||
static const unsigned int register_channel[] = {
|
||||
[INA3221_SHUNT1] = INA3221_CHANNEL1,
|
||||
[INA3221_SHUNT2] = INA3221_CHANNEL2,
|
||||
[INA3221_SHUNT3] = INA3221_CHANNEL3,
|
||||
[INA3221_CRIT1] = INA3221_CHANNEL1,
|
||||
[INA3221_CRIT2] = INA3221_CHANNEL2,
|
||||
[INA3221_CRIT3] = INA3221_CHANNEL3,
|
||||
[INA3221_WARN1] = INA3221_CHANNEL1,
|
||||
[INA3221_WARN2] = INA3221_CHANNEL2,
|
||||
[INA3221_WARN3] = INA3221_CHANNEL3,
|
||||
};
|
||||
|
||||
/**
|
||||
* struct ina3221_data - device specific information
|
||||
* @regmap: Register map of the device
|
||||
* @fields: Register fields of the device
|
||||
* @shunt_resistors: Array of resistor values per channel
|
||||
*/
|
||||
struct ina3221_data {
|
||||
struct regmap *regmap;
|
||||
struct regmap_field *fields[F_MAX_FIELDS];
|
||||
unsigned int shunt_resistors[INA3221_NUM_CHANNELS];
|
||||
};
|
||||
|
||||
static int ina3221_read_value(struct ina3221_data *ina, unsigned int reg,
|
||||
int *val)
|
||||
{
|
||||
unsigned int regval;
|
||||
int ret;
|
||||
|
||||
ret = regmap_read(ina->regmap, reg, ®val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
*val = sign_extend32(regval >> 3, 12);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static ssize_t ina3221_show_bus_voltage(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int reg = sd_attr->index;
|
||||
int val, voltage_mv, ret;
|
||||
|
||||
ret = ina3221_read_value(ina, reg, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
voltage_mv = val * 8;
|
||||
|
||||
return snprintf(buf, PAGE_SIZE, "%d\n", voltage_mv);
|
||||
}
|
||||
|
||||
static ssize_t ina3221_show_shunt_voltage(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int reg = sd_attr->index;
|
||||
int val, voltage_uv, ret;
|
||||
|
||||
ret = ina3221_read_value(ina, reg, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
voltage_uv = val * 40;
|
||||
|
||||
return snprintf(buf, PAGE_SIZE, "%d\n", voltage_uv);
|
||||
}
|
||||
|
||||
static ssize_t ina3221_show_current(struct device *dev,
|
||||
struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int reg = sd_attr->index;
|
||||
unsigned int channel = register_channel[reg];
|
||||
unsigned int resistance_uo = ina->shunt_resistors[channel];
|
||||
int val, current_ma, voltage_nv, ret;
|
||||
|
||||
ret = ina3221_read_value(ina, reg, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
voltage_nv = val * 40000;
|
||||
|
||||
current_ma = DIV_ROUND_CLOSEST(voltage_nv, resistance_uo);
|
||||
|
||||
return snprintf(buf, PAGE_SIZE, "%d\n", current_ma);
|
||||
}
|
||||
|
||||
static ssize_t ina3221_set_current(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
const char *buf, size_t count)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int reg = sd_attr->index;
|
||||
unsigned int channel = register_channel[reg];
|
||||
unsigned int resistance_uo = ina->shunt_resistors[channel];
|
||||
int val, current_ma, voltage_uv, ret;
|
||||
|
||||
ret = kstrtoint(buf, 0, ¤t_ma);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/* clamp current */
|
||||
current_ma = clamp_val(current_ma,
|
||||
INT_MIN / resistance_uo,
|
||||
INT_MAX / resistance_uo);
|
||||
|
||||
voltage_uv = DIV_ROUND_CLOSEST(current_ma * resistance_uo, 1000);
|
||||
|
||||
/* clamp voltage */
|
||||
voltage_uv = clamp_val(voltage_uv, -163800, 163800);
|
||||
|
||||
/* 1 / 40uV(scale) << 3(register shift) = 5 */
|
||||
val = DIV_ROUND_CLOSEST(voltage_uv, 5) & 0xfff8;
|
||||
|
||||
ret = regmap_write(ina->regmap, reg, val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
return count;
|
||||
}
|
||||
|
||||
static ssize_t ina3221_show_shunt(struct device *dev,
|
||||
struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int channel = sd_attr->index;
|
||||
unsigned int resistance_uo;
|
||||
|
||||
resistance_uo = ina->shunt_resistors[channel];
|
||||
|
||||
return snprintf(buf, PAGE_SIZE, "%d\n", resistance_uo);
|
||||
}
|
||||
|
||||
static ssize_t ina3221_set_shunt(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
const char *buf, size_t count)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int channel = sd_attr->index;
|
||||
unsigned int val;
|
||||
int ret;
|
||||
|
||||
ret = kstrtouint(buf, 0, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
if (val == 0)
|
||||
return -EINVAL;
|
||||
|
||||
ina->shunt_resistors[channel] = val;
|
||||
|
||||
return count;
|
||||
}
|
||||
|
||||
static ssize_t ina3221_show_alert(struct device *dev,
|
||||
struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sd_attr = to_sensor_dev_attr(attr);
|
||||
struct ina3221_data *ina = dev_get_drvdata(dev);
|
||||
unsigned int field = sd_attr->index;
|
||||
unsigned int regval;
|
||||
int ret;
|
||||
|
||||
ret = regmap_field_read(ina->fields[field], ®val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
return snprintf(buf, PAGE_SIZE, "%d\n", regval);
|
||||
}
|
||||
|
||||
/* bus voltage */
|
||||
static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO,
|
||||
ina3221_show_bus_voltage, NULL, INA3221_BUS1);
|
||||
static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO,
|
||||
ina3221_show_bus_voltage, NULL, INA3221_BUS2);
|
||||
static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO,
|
||||
ina3221_show_bus_voltage, NULL, INA3221_BUS3);
|
||||
|
||||
/* calculated current */
|
||||
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO,
|
||||
ina3221_show_current, NULL, INA3221_SHUNT1);
|
||||
static SENSOR_DEVICE_ATTR(curr2_input, S_IRUGO,
|
||||
ina3221_show_current, NULL, INA3221_SHUNT2);
|
||||
static SENSOR_DEVICE_ATTR(curr3_input, S_IRUGO,
|
||||
ina3221_show_current, NULL, INA3221_SHUNT3);
|
||||
|
||||
/* shunt resistance */
|
||||
static SENSOR_DEVICE_ATTR(shunt1_resistor, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_shunt, ina3221_set_shunt, INA3221_CHANNEL1);
|
||||
static SENSOR_DEVICE_ATTR(shunt2_resistor, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_shunt, ina3221_set_shunt, INA3221_CHANNEL2);
|
||||
static SENSOR_DEVICE_ATTR(shunt3_resistor, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_shunt, ina3221_set_shunt, INA3221_CHANNEL3);
|
||||
|
||||
/* critical current */
|
||||
static SENSOR_DEVICE_ATTR(curr1_crit, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_CRIT1);
|
||||
static SENSOR_DEVICE_ATTR(curr2_crit, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_CRIT2);
|
||||
static SENSOR_DEVICE_ATTR(curr3_crit, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_CRIT3);
|
||||
|
||||
/* critical current alert */
|
||||
static SENSOR_DEVICE_ATTR(curr1_crit_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_CF1);
|
||||
static SENSOR_DEVICE_ATTR(curr2_crit_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_CF2);
|
||||
static SENSOR_DEVICE_ATTR(curr3_crit_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_CF3);
|
||||
|
||||
/* warning current */
|
||||
static SENSOR_DEVICE_ATTR(curr1_max, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_WARN1);
|
||||
static SENSOR_DEVICE_ATTR(curr2_max, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_WARN2);
|
||||
static SENSOR_DEVICE_ATTR(curr3_max, S_IRUGO | S_IWUSR,
|
||||
ina3221_show_current, ina3221_set_current, INA3221_WARN3);
|
||||
|
||||
/* warning current alert */
|
||||
static SENSOR_DEVICE_ATTR(curr1_max_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_WF1);
|
||||
static SENSOR_DEVICE_ATTR(curr2_max_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_WF2);
|
||||
static SENSOR_DEVICE_ATTR(curr3_max_alarm, S_IRUGO,
|
||||
ina3221_show_alert, NULL, F_WF3);
|
||||
|
||||
/* shunt voltage */
|
||||
static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO,
|
||||
ina3221_show_shunt_voltage, NULL, INA3221_SHUNT1);
|
||||
static SENSOR_DEVICE_ATTR(in5_input, S_IRUGO,
|
||||
ina3221_show_shunt_voltage, NULL, INA3221_SHUNT2);
|
||||
static SENSOR_DEVICE_ATTR(in6_input, S_IRUGO,
|
||||
ina3221_show_shunt_voltage, NULL, INA3221_SHUNT3);
|
||||
|
||||
static struct attribute *ina3221_attrs[] = {
|
||||
/* channel 1 */
|
||||
&sensor_dev_attr_in1_input.dev_attr.attr,
|
||||
&sensor_dev_attr_curr1_input.dev_attr.attr,
|
||||
&sensor_dev_attr_shunt1_resistor.dev_attr.attr,
|
||||
&sensor_dev_attr_curr1_crit.dev_attr.attr,
|
||||
&sensor_dev_attr_curr1_crit_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_curr1_max.dev_attr.attr,
|
||||
&sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_in4_input.dev_attr.attr,
|
||||
|
||||
/* channel 2 */
|
||||
&sensor_dev_attr_in2_input.dev_attr.attr,
|
||||
&sensor_dev_attr_curr2_input.dev_attr.attr,
|
||||
&sensor_dev_attr_shunt2_resistor.dev_attr.attr,
|
||||
&sensor_dev_attr_curr2_crit.dev_attr.attr,
|
||||
&sensor_dev_attr_curr2_crit_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_curr2_max.dev_attr.attr,
|
||||
&sensor_dev_attr_curr2_max_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_in5_input.dev_attr.attr,
|
||||
|
||||
/* channel 3 */
|
||||
&sensor_dev_attr_in3_input.dev_attr.attr,
|
||||
&sensor_dev_attr_curr3_input.dev_attr.attr,
|
||||
&sensor_dev_attr_shunt3_resistor.dev_attr.attr,
|
||||
&sensor_dev_attr_curr3_crit.dev_attr.attr,
|
||||
&sensor_dev_attr_curr3_crit_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_curr3_max.dev_attr.attr,
|
||||
&sensor_dev_attr_curr3_max_alarm.dev_attr.attr,
|
||||
&sensor_dev_attr_in6_input.dev_attr.attr,
|
||||
|
||||
NULL,
|
||||
};
|
||||
ATTRIBUTE_GROUPS(ina3221);
|
||||
|
||||
static const struct regmap_range ina3221_yes_ranges[] = {
|
||||
regmap_reg_range(INA3221_SHUNT1, INA3221_BUS3),
|
||||
regmap_reg_range(INA3221_MASK_ENABLE, INA3221_MASK_ENABLE),
|
||||
};
|
||||
|
||||
static const struct regmap_access_table ina3221_volatile_table = {
|
||||
.yes_ranges = ina3221_yes_ranges,
|
||||
.n_yes_ranges = ARRAY_SIZE(ina3221_yes_ranges),
|
||||
};
|
||||
|
||||
static const struct regmap_config ina3221_regmap_config = {
|
||||
.reg_bits = 8,
|
||||
.val_bits = 16,
|
||||
|
||||
.cache_type = REGCACHE_RBTREE,
|
||||
.volatile_table = &ina3221_volatile_table,
|
||||
};
|
||||
|
||||
static int ina3221_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct device *dev = &client->dev;
|
||||
struct ina3221_data *ina;
|
||||
struct device *hwmon_dev;
|
||||
int i, ret;
|
||||
|
||||
ina = devm_kzalloc(dev, sizeof(*ina), GFP_KERNEL);
|
||||
if (!ina)
|
||||
return -ENOMEM;
|
||||
|
||||
ina->regmap = devm_regmap_init_i2c(client, &ina3221_regmap_config);
|
||||
if (IS_ERR(ina->regmap)) {
|
||||
dev_err(dev, "Unable to allocate register map\n");
|
||||
return PTR_ERR(ina->regmap);
|
||||
}
|
||||
|
||||
for (i = 0; i < F_MAX_FIELDS; i++) {
|
||||
ina->fields[i] = devm_regmap_field_alloc(dev,
|
||||
ina->regmap,
|
||||
ina3221_reg_fields[i]);
|
||||
if (IS_ERR(ina->fields[i])) {
|
||||
dev_err(dev, "Unable to allocate regmap fields\n");
|
||||
return PTR_ERR(ina->fields[i]);
|
||||
}
|
||||
}
|
||||
|
||||
for (i = 0; i < INA3221_NUM_CHANNELS; i++)
|
||||
ina->shunt_resistors[i] = INA3221_RSHUNT_DEFAULT;
|
||||
|
||||
ret = regmap_field_write(ina->fields[F_RST], true);
|
||||
if (ret) {
|
||||
dev_err(dev, "Unable to reset device\n");
|
||||
return ret;
|
||||
}
|
||||
|
||||
hwmon_dev = devm_hwmon_device_register_with_groups(dev,
|
||||
client->name,
|
||||
ina, ina3221_groups);
|
||||
if (IS_ERR(hwmon_dev)) {
|
||||
dev_err(dev, "Unable to register hwmon device\n");
|
||||
return PTR_ERR(hwmon_dev);
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct of_device_id ina3221_of_match_table[] = {
|
||||
{ .compatible = "ti,ina3221", },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, ina3221_of_match_table);
|
||||
|
||||
static const struct i2c_device_id ina3221_ids[] = {
|
||||
{ "ina3221", 0 },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, ina3221_ids);
|
||||
|
||||
static struct i2c_driver ina3221_i2c_driver = {
|
||||
.probe = ina3221_probe,
|
||||
.driver = {
|
||||
.name = INA3221_DRIVER_NAME,
|
||||
.of_match_table = ina3221_of_match_table,
|
||||
},
|
||||
.id_table = ina3221_ids,
|
||||
};
|
||||
module_i2c_driver(ina3221_i2c_driver);
|
||||
|
||||
MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
|
||||
MODULE_DESCRIPTION("Texas Instruments INA3221 HWMon Driver");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
Loading…
Reference in New Issue
Block a user