AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity

pinctrl: nomadik: improve GPIO debug prints

Browse Source 
The debugfs file would only define if the line was "pulled" and
not which direction (pull up or pull down). Improve this by
taking two print paths depending on whether the pin is set as
input or output and use the data register directly to figure
out whether the pin is set for pull up or pull down.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
Linus Walleij 2014-09-30 15:05:21 +02:00
parent 259145feff
commit 8f1774a2a9
1 changed files with 25 additions and 11 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

36
drivers/pinctrl/nomadik/pinctrl-nomadik.c
View File

@ -986,6 +986,7 @@ static void nmk_gpio_dbg_show_one(struct seq_file *s,
container_of(chip, struct nmk_gpio_chip, chip);
int mode;
bool is_out;
bool data_out;
bool pull;
u32 bit = 1 << offset;
const char *modes[] = {
@ -998,28 +999,41 @@ static void nmk_gpio_dbg_show_one(struct seq_file *s,
[NMK_GPIO_ALT_C+3] = "altC3",
[NMK_GPIO_ALT_C+4] = "altC4",
};
const char *pulls[] = {
"none ",
"pull down",
"pull up ",
};
clk_enable(nmk_chip->clk);
is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & bit);
pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & bit);
data_out = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & bit);
mode = nmk_gpio_get_mode(gpio);
if ((mode == NMK_GPIO_ALT_C) && pctldev)
mode = nmk_prcm_gpiocr_get_mode(pctldev, gpio);
seq_printf(s, " gpio-%-3d (%-20.20s) %s %s %s %s",
gpio, label ?: "(none)",
is_out ? "out" : "in ",
chip->get
? (chip->get(chip, offset) ? "hi" : "lo")
: "? ",
(mode < 0) ? "unknown" : modes[mode],
pull ? "pull" : "none");
if (!is_out) {
if (is_out) {
seq_printf(s, " gpio-%-3d (%-20.20s) out %s %s",
gpio,
label ?: "(none)",
data_out ? "hi" : "lo",
(mode < 0) ? "unknown" : modes[mode]);
} else {
int irq = gpio_to_irq(gpio);
struct irq_desc *desc = irq_to_desc(irq);
int pullidx = 0;
/* This races with request_irq(), set_irq_type(),
if (pull)
pullidx = data_out ? 1 : 2;
seq_printf(s, " gpio-%-3d (%-20.20s) in %s %s",
gpio,
label ?: "(none)",
pulls[pullidx],
(mode < 0) ? "unknown" : modes[mode]);
/*
* This races with request_irq(), set_irq_type(),
* and set_irq_wake() ... but those are "rare".
*/
if (irq > 0 && desc && desc->action) {