forked from luck/tmp_suning_uos_patched
ARM: 6054/1: AT91: taskit PortuxG20 and Stamp9G20 board support
Both boards share the same board file, as the PortuxG20 is basically an SBC based on the Stamp9G20. Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
Christian Glindkamp
Russell King
parent
3971047930
commit
9b404b7cc3
@ -360,6 +360,19 @@ config MACH_CPU9G20
|
||||
Select this if you are using a Eukrea Electromatique's
|
||||
CPU9G20 Board <http://www.eukrea.com/>
|
||||
|
||||
config MACH_PORTUXG20
|
||||
bool "taskit PortuxG20"
|
||||
help
|
||||
Select this if you are using taskit's PortuxG20.
|
||||
<http://www.taskit.de/en/>
|
||||
|
||||
config MACH_STAMP9G20
|
||||
bool "taskit Stamp9G20 CPU module"
|
||||
help
|
||||
Select this if you are using taskit's Stamp9G20 CPU module on its
|
||||
evaluation board.
|
||||
<http://www.taskit.de/en/>
|
||||
|
||||
endif
|
||||
|
||||
# ----------------------------------------------------------
|
||||
|
||||
@ -63,6 +63,8 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
|
||||
obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
|
||||
obj-$(CONFIG_MACH_AT91SAM9G20EK_2MMC) += board-sam9g20ek-2slot-mmc.o
|
||||
obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o
|
||||
obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o
|
||||
obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o
|
||||
|
||||
# AT91SAM9G45 board-specific support
|
||||
obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o
|
||||
|
||||
315
arch/arm/mach-at91/board-stamp9g20.c
Normal file
315
arch/arm/mach-at91/board-stamp9g20.c
Normal file
@ -0,0 +1,315 @@
|
||||
/*
|
||||
* Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
|
||||
* taskit GmbH
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
||||
*/
|
||||
|
||||
#include <linux/mm.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/w1-gpio.h>
|
||||
|
||||
#include <asm/mach-types.h>
|
||||
#include <asm/mach/arch.h>
|
||||
|
||||
#include <mach/board.h>
|
||||
#include <mach/at91sam9_smc.h>
|
||||
|
||||
#include "sam9_smc.h"
|
||||
#include "generic.h"
|
||||
|
||||
|
||||
static void __init portuxg20_map_io(void)
|
||||
{
|
||||
/* Initialize processor: 18.432 MHz crystal */
|
||||
at91sam9260_initialize(18432000);
|
||||
|
||||
/* DGBU on ttyS0. (Rx & Tx only) */
|
||||
at91_register_uart(0, 0, 0);
|
||||
|
||||
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
||||
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
|
||||
| ATMEL_UART_DTR | ATMEL_UART_DSR
|
||||
| ATMEL_UART_DCD | ATMEL_UART_RI);
|
||||
|
||||
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
|
||||
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
|
||||
|
||||
/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
|
||||
at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
|
||||
|
||||
/* USART4 on ttyS5. (Rx, Tx only) */
|
||||
at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
|
||||
|
||||
/* USART5 on ttyS6. (Rx, Tx only) */
|
||||
at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
|
||||
|
||||
/* set serial console to ttyS0 (ie, DBGU) */
|
||||
at91_set_serial_console(0);
|
||||
}
|
||||
|
||||
static void __init stamp9g20_map_io(void)
|
||||
{
|
||||
/* Initialize processor: 18.432 MHz crystal */
|
||||
at91sam9260_initialize(18432000);
|
||||
|
||||
/* DGBU on ttyS0. (Rx & Tx only) */
|
||||
at91_register_uart(0, 0, 0);
|
||||
|
||||
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
||||
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
|
||||
| ATMEL_UART_DTR | ATMEL_UART_DSR
|
||||
| ATMEL_UART_DCD | ATMEL_UART_RI);
|
||||
|
||||
/* set serial console to ttyS0 (ie, DBGU) */
|
||||
at91_set_serial_console(0);
|
||||
}
|
||||
|
||||
static void __init init_irq(void)
|
||||
{
|
||||
at91sam9260_init_interrupts(NULL);
|
||||
}
|
||||
|
||||
|
||||
/*
|
||||
* NAND flash
|
||||
*/
|
||||
static struct atmel_nand_data __initdata nand_data = {
|
||||
.ale = 21,
|
||||
.cle = 22,
|
||||
.rdy_pin = AT91_PIN_PC13,
|
||||
.enable_pin = AT91_PIN_PC14,
|
||||
.bus_width_16 = 0,
|
||||
};
|
||||
|
||||
static struct sam9_smc_config __initdata nand_smc_config = {
|
||||
.ncs_read_setup = 0,
|
||||
.nrd_setup = 2,
|
||||
.ncs_write_setup = 0,
|
||||
.nwe_setup = 2,
|
||||
|
||||
.ncs_read_pulse = 4,
|
||||
.nrd_pulse = 4,
|
||||
.ncs_write_pulse = 4,
|
||||
.nwe_pulse = 4,
|
||||
|
||||
.read_cycle = 7,
|
||||
.write_cycle = 7,
|
||||
|
||||
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
|
||||
.tdf_cycles = 3,
|
||||
};
|
||||
|
||||
static void __init add_device_nand(void)
|
||||
{
|
||||
/* configure chip-select 3 (NAND) */
|
||||
sam9_smc_configure(3, &nand_smc_config);
|
||||
|
||||
at91_add_device_nand(&nand_data);
|
||||
}
|
||||
|
||||
|
||||
/*
|
||||
* MCI (SD/MMC)
|
||||
* det_pin, wp_pin and vcc_pin are not connected
|
||||
*/
|
||||
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
|
||||
static struct mci_platform_data __initdata mmc_data = {
|
||||
.slot[0] = {
|
||||
.bus_width = 4,
|
||||
},
|
||||
};
|
||||
#else
|
||||
static struct at91_mmc_data __initdata mmc_data = {
|
||||
.slot_b = 0,
|
||||
.wire4 = 1,
|
||||
};
|
||||
#endif
|
||||
|
||||
|
||||
/*
|
||||
* USB Host port
|
||||
*/
|
||||
static struct at91_usbh_data __initdata usbh_data = {
|
||||
.ports = 2,
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* USB Device port
|
||||
*/
|
||||
static struct at91_udc_data __initdata portuxg20_udc_data = {
|
||||
.vbus_pin = AT91_PIN_PC7,
|
||||
.pullup_pin = 0, /* pull-up driven by UDC */
|
||||
};
|
||||
|
||||
static struct at91_udc_data __initdata stamp9g20_udc_data = {
|
||||
.vbus_pin = AT91_PIN_PA22,
|
||||
.pullup_pin = 0, /* pull-up driven by UDC */
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* MACB Ethernet device
|
||||
*/
|
||||
static struct at91_eth_data __initdata macb_data = {
|
||||
.phy_irq_pin = AT91_PIN_PA28,
|
||||
.is_rmii = 1,
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* LEDs
|
||||
*/
|
||||
static struct gpio_led portuxg20_leds[] = {
|
||||
{
|
||||
.name = "LED2",
|
||||
.gpio = AT91_PIN_PC5,
|
||||
.default_trigger = "none",
|
||||
}, {
|
||||
.name = "LED3",
|
||||
.gpio = AT91_PIN_PC4,
|
||||
.default_trigger = "none",
|
||||
}, {
|
||||
.name = "LED4",
|
||||
.gpio = AT91_PIN_PC10,
|
||||
.default_trigger = "heartbeat",
|
||||
}
|
||||
};
|
||||
|
||||
static struct gpio_led stamp9g20_leds[] = {
|
||||
{
|
||||
.name = "D8",
|
||||
.gpio = AT91_PIN_PB18,
|
||||
.active_low = 1,
|
||||
.default_trigger = "none",
|
||||
}, {
|
||||
.name = "D9",
|
||||
.gpio = AT91_PIN_PB19,
|
||||
.active_low = 1,
|
||||
.default_trigger = "none",
|
||||
}, {
|
||||
.name = "D10",
|
||||
.gpio = AT91_PIN_PB20,
|
||||
.active_low = 1,
|
||||
.default_trigger = "heartbeat",
|
||||
}
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* SPI devices
|
||||
*/
|
||||
static struct spi_board_info portuxg20_spi_devices[] = {
|
||||
{
|
||||
.modalias = "spidev",
|
||||
.chip_select = 0,
|
||||
.max_speed_hz = 1 * 1000 * 1000,
|
||||
.bus_num = 0,
|
||||
}, {
|
||||
.modalias = "spidev",
|
||||
.chip_select = 0,
|
||||
.max_speed_hz = 1 * 1000 * 1000,
|
||||
.bus_num = 1,
|
||||
},
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* Dallas 1-Wire
|
||||
*/
|
||||
static struct w1_gpio_platform_data w1_gpio_pdata = {
|
||||
.pin = AT91_PIN_PA29,
|
||||
.is_open_drain = 1,
|
||||
};
|
||||
|
||||
static struct platform_device w1_device = {
|
||||
.name = "w1-gpio",
|
||||
.id = -1,
|
||||
.dev.platform_data = &w1_gpio_pdata,
|
||||
};
|
||||
|
||||
void add_w1(void)
|
||||
{
|
||||
at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
|
||||
at91_set_multi_drive(w1_gpio_pdata.pin, 1);
|
||||
platform_device_register(&w1_device);
|
||||
}
|
||||
|
||||
|
||||
static void __init generic_board_init(void)
|
||||
{
|
||||
/* Serial */
|
||||
at91_add_device_serial();
|
||||
/* NAND */
|
||||
add_device_nand();
|
||||
/* MMC */
|
||||
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
|
||||
at91_add_device_mci(0, &mmc_data);
|
||||
#else
|
||||
at91_add_device_mmc(0, &mmc_data);
|
||||
#endif
|
||||
/* USB Host */
|
||||
at91_add_device_usbh(&usbh_data);
|
||||
/* Ethernet */
|
||||
at91_add_device_eth(&macb_data);
|
||||
/* I2C */
|
||||
at91_add_device_i2c(NULL, 0);
|
||||
/* W1 */
|
||||
add_w1();
|
||||
}
|
||||
|
||||
static void __init portuxg20_board_init(void)
|
||||
{
|
||||
generic_board_init();
|
||||
/* SPI */
|
||||
at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
|
||||
/* USB Device */
|
||||
at91_add_device_udc(&portuxg20_udc_data);
|
||||
/* LEDs */
|
||||
at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds));
|
||||
}
|
||||
|
||||
static void __init stamp9g20_board_init(void)
|
||||
{
|
||||
generic_board_init();
|
||||
/* USB Device */
|
||||
at91_add_device_udc(&stamp9g20_udc_data);
|
||||
/* LEDs */
|
||||
at91_gpio_leds(stamp9g20_leds, ARRAY_SIZE(stamp9g20_leds));
|
||||
}
|
||||
|
||||
MACHINE_START(PORTUXG20, "taskit PortuxG20")
|
||||
/* Maintainer: taskit GmbH */
|
||||
.phys_io = AT91_BASE_SYS,
|
||||
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
|
||||
.boot_params = AT91_SDRAM_BASE + 0x100,
|
||||
.timer = &at91sam926x_timer,
|
||||
.map_io = portuxg20_map_io,
|
||||
.init_irq = init_irq,
|
||||
.init_machine = portuxg20_board_init,
|
||||
MACHINE_END
|
||||
|
||||
MACHINE_START(STAMP9G20, "taskit Stamp9G20")
|
||||
/* Maintainer: taskit GmbH */
|
||||
.phys_io = AT91_BASE_SYS,
|
||||
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
|
||||
.boot_params = AT91_SDRAM_BASE + 0x100,
|
||||
.timer = &at91sam926x_timer,
|
||||
.map_io = stamp9g20_map_io,
|
||||
.init_irq = init_irq,
|
||||
.init_machine = stamp9g20_board_init,
|
||||
MACHINE_END
|
||||
Loading…
Reference in New Issue
Block a user