forked from luck/tmp_suning_uos_patched
[ALSA] Fix missing suspend/resume-code for ens1371
Modules: ENS1370/1+ driver This patch fixes missing suspend/resume-code for snd-ens1371 (but not for snd-ens1370) Signed-off-by: Kurt J. Bosch <kjb-temp-2005@gmx.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is contained in:
Kurt J. Bosch
Jaroslav Kysela
parent
26741b5512
commit
f31a31b902
|
|
@ -19,6 +19,13 @@
|
|||
*
|
||||
*/
|
||||
|
||||
/* Power-Management-Code ( CONFIG_PM )
|
||||
* for ens1371 only ( FIXME )
|
||||
* derived from cs4281.c, atiixp.c and via82xx.c
|
||||
* using http://www.alsa-project.org/~iwai/writing-an-alsa-driver/c1540.htm
|
||||
* by Kurt J. Bosch
|
||||
*/
|
||||
|
||||
#include <sound/driver.h>
|
||||
#include <asm/io.h>
|
||||
#include <linux/delay.h>
|
||||
|
|
@ -1924,6 +1931,117 @@ static struct {
|
|||
};
|
||||
#endif
|
||||
|
||||
static void snd_ensoniq_chip_init(ensoniq_t * ensoniq)
|
||||
{
|
||||
#ifdef CHIP1371
|
||||
int idx;
|
||||
struct pci_dev *pci = ensoniq->pci;
|
||||
#endif
|
||||
// this code was part of snd_ensoniq_create before intruduction of suspend/resume
|
||||
#ifdef CHIP1370
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
outl(ensoniq->sctrl, ES_REG(ensoniq, SERIAL));
|
||||
outl(ES_MEM_PAGEO(ES_PAGE_ADC), ES_REG(ensoniq, MEM_PAGE));
|
||||
outl(ensoniq->dma_bug.addr, ES_REG(ensoniq, PHANTOM_FRAME));
|
||||
outl(0, ES_REG(ensoniq, PHANTOM_COUNT));
|
||||
#else
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
outl(ensoniq->sctrl, ES_REG(ensoniq, SERIAL));
|
||||
outl(0, ES_REG(ensoniq, 1371_LEGACY));
|
||||
for (idx = 0; es1371_ac97_reset_hack[idx].vid != (unsigned short)PCI_ANY_ID; idx++)
|
||||
if (pci->vendor == es1371_ac97_reset_hack[idx].vid &&
|
||||
pci->device == es1371_ac97_reset_hack[idx].did &&
|
||||
ensoniq->rev == es1371_ac97_reset_hack[idx].rev) {
|
||||
outl(ensoniq->cssr, ES_REG(ensoniq, STATUS));
|
||||
/* need to delay around 20ms(bleech) to give
|
||||
some CODECs enough time to wakeup */
|
||||
msleep(20);
|
||||
break;
|
||||
}
|
||||
/* AC'97 warm reset to start the bitclk */
|
||||
outl(ensoniq->ctrl | ES_1371_SYNC_RES, ES_REG(ensoniq, CONTROL));
|
||||
inl(ES_REG(ensoniq, CONTROL));
|
||||
udelay(20);
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
/* Init the sample rate converter */
|
||||
snd_es1371_wait_src_ready(ensoniq);
|
||||
outl(ES_1371_SRC_DISABLE, ES_REG(ensoniq, 1371_SMPRATE));
|
||||
for (idx = 0; idx < 0x80; idx++)
|
||||
snd_es1371_src_write(ensoniq, idx, 0);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC1 + ES_SMPREG_TRUNC_N, 16 << 4);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC1 + ES_SMPREG_INT_REGS, 16 << 10);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC2 + ES_SMPREG_TRUNC_N, 16 << 4);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC2 + ES_SMPREG_INT_REGS, 16 << 10);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_ADC, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_ADC + 1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC1 + 1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC2, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC2 + 1, 1 << 12);
|
||||
snd_es1371_adc_rate(ensoniq, 22050);
|
||||
snd_es1371_dac1_rate(ensoniq, 22050);
|
||||
snd_es1371_dac2_rate(ensoniq, 22050);
|
||||
/* WARNING:
|
||||
* enabling the sample rate converter without properly programming
|
||||
* its parameters causes the chip to lock up (the SRC busy bit will
|
||||
* be stuck high, and I've found no way to rectify this other than
|
||||
* power cycle) - Thomas Sailer
|
||||
*/
|
||||
snd_es1371_wait_src_ready(ensoniq);
|
||||
outl(0, ES_REG(ensoniq, 1371_SMPRATE));
|
||||
/* try reset codec directly */
|
||||
outl(ES_1371_CODEC_WRITE(0, 0), ES_REG(ensoniq, 1371_CODEC));
|
||||
#endif
|
||||
outb(ensoniq->uartc = 0x00, ES_REG(ensoniq, UART_CONTROL));
|
||||
outb(0x00, ES_REG(ensoniq, UART_RES));
|
||||
outl(ensoniq->cssr, ES_REG(ensoniq, STATUS));
|
||||
synchronize_irq(ensoniq->irq);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PM
|
||||
static int snd_ensoniq_suspend (snd_card_t * card,
|
||||
pm_message_t state)
|
||||
{
|
||||
ensoniq_t *ensoniq = card->pm_private_data;
|
||||
|
||||
snd_pcm_suspend_all(ensoniq->pcm1);
|
||||
snd_pcm_suspend_all(ensoniq->pcm2);
|
||||
|
||||
#ifdef CHIP1371
|
||||
if (ensoniq->u.es1371.ac97)
|
||||
snd_ac97_suspend(ensoniq->u.es1371.ac97);
|
||||
#else
|
||||
/* FIXME */
|
||||
#endif
|
||||
pci_set_power_state(ensoniq->pci, 3);
|
||||
pci_disable_device(ensoniq->pci);
|
||||
// snd_power_change_state(card, SNDRV_CTL_POWER_D3hot); // only 2.6.10
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int snd_ensoniq_resume (snd_card_t * card
|
||||
)
|
||||
{
|
||||
ensoniq_t *ensoniq = card->pm_private_data;
|
||||
|
||||
pci_enable_device(ensoniq->pci);
|
||||
pci_set_power_state(ensoniq->pci, 0);
|
||||
pci_set_master(ensoniq->pci);
|
||||
|
||||
snd_ensoniq_chip_init(ensoniq);
|
||||
|
||||
#ifdef CHIP1371
|
||||
if (ensoniq->u.es1371.ac97)
|
||||
snd_ac97_resume(ensoniq->u.es1371.ac97);
|
||||
#else
|
||||
/* FIXME */
|
||||
#endif
|
||||
// snd_power_change_state(card, SNDRV_CTL_POWER_D0); // only 2.6.10
|
||||
return 0;
|
||||
}
|
||||
#endif /* CONFIG_PM */
|
||||
|
||||
|
||||
static int __devinit snd_ensoniq_create(snd_card_t * card,
|
||||
struct pci_dev *pci,
|
||||
ensoniq_t ** rensoniq)
|
||||
|
|
@ -1986,12 +2104,6 @@ static int __devinit snd_ensoniq_create(snd_card_t * card,
|
|||
ensoniq->ctrl = ES_1370_CDC_EN | ES_1370_PCLKDIVO(ES_1370_SRTODIV(8000));
|
||||
#endif
|
||||
ensoniq->sctrl = 0;
|
||||
/* initialize the chips */
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
outl(ensoniq->sctrl, ES_REG(ensoniq, SERIAL));
|
||||
outl(ES_MEM_PAGEO(ES_PAGE_ADC), ES_REG(ensoniq, MEM_PAGE));
|
||||
outl(ensoniq->dma_bug.addr, ES_REG(ensoniq, PHANTOM_FRAME));
|
||||
outl(0, ES_REG(ensoniq, PHANTOM_COUNT));
|
||||
#else
|
||||
ensoniq->ctrl = 0;
|
||||
ensoniq->sctrl = 0;
|
||||
|
|
@ -2002,59 +2114,16 @@ static int __devinit snd_ensoniq_create(snd_card_t * card,
|
|||
ensoniq->ctrl |= ES_1371_GPIO_OUT(1); /* turn amplifier on */
|
||||
break;
|
||||
}
|
||||
/* initialize the chips */
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
outl(ensoniq->sctrl, ES_REG(ensoniq, SERIAL));
|
||||
outl(0, ES_REG(ensoniq, 1371_LEGACY));
|
||||
for (idx = 0; es1371_ac97_reset_hack[idx].vid != (unsigned short)PCI_ANY_ID; idx++)
|
||||
if (pci->vendor == es1371_ac97_reset_hack[idx].vid &&
|
||||
pci->device == es1371_ac97_reset_hack[idx].did &&
|
||||
ensoniq->rev == es1371_ac97_reset_hack[idx].rev) {
|
||||
ensoniq->cssr |= ES_1371_ST_AC97_RST;
|
||||
outl(ensoniq->cssr, ES_REG(ensoniq, STATUS));
|
||||
/* need to delay around 20ms(bleech) to give
|
||||
some CODECs enough time to wakeup */
|
||||
msleep(20);
|
||||
break;
|
||||
}
|
||||
/* AC'97 warm reset to start the bitclk */
|
||||
outl(ensoniq->ctrl | ES_1371_SYNC_RES, ES_REG(ensoniq, CONTROL));
|
||||
inl(ES_REG(ensoniq, CONTROL));
|
||||
udelay(20);
|
||||
outl(ensoniq->ctrl, ES_REG(ensoniq, CONTROL));
|
||||
/* Init the sample rate converter */
|
||||
snd_es1371_wait_src_ready(ensoniq);
|
||||
outl(ES_1371_SRC_DISABLE, ES_REG(ensoniq, 1371_SMPRATE));
|
||||
for (idx = 0; idx < 0x80; idx++)
|
||||
snd_es1371_src_write(ensoniq, idx, 0);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC1 + ES_SMPREG_TRUNC_N, 16 << 4);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC1 + ES_SMPREG_INT_REGS, 16 << 10);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC2 + ES_SMPREG_TRUNC_N, 16 << 4);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_DAC2 + ES_SMPREG_INT_REGS, 16 << 10);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_ADC, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_ADC + 1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC1 + 1, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC2, 1 << 12);
|
||||
snd_es1371_src_write(ensoniq, ES_SMPREG_VOL_DAC2 + 1, 1 << 12);
|
||||
snd_es1371_adc_rate(ensoniq, 22050);
|
||||
snd_es1371_dac1_rate(ensoniq, 22050);
|
||||
snd_es1371_dac2_rate(ensoniq, 22050);
|
||||
/* WARNING:
|
||||
* enabling the sample rate converter without properly programming
|
||||
* its parameters causes the chip to lock up (the SRC busy bit will
|
||||
* be stuck high, and I've found no way to rectify this other than
|
||||
* power cycle) - Thomas Sailer
|
||||
*/
|
||||
snd_es1371_wait_src_ready(ensoniq);
|
||||
outl(0, ES_REG(ensoniq, 1371_SMPRATE));
|
||||
/* try reset codec directly */
|
||||
outl(ES_1371_CODEC_WRITE(0, 0), ES_REG(ensoniq, 1371_CODEC));
|
||||
#endif
|
||||
outb(ensoniq->uartc = 0x00, ES_REG(ensoniq, UART_CONTROL));
|
||||
outb(0x00, ES_REG(ensoniq, UART_RES));
|
||||
outl(ensoniq->cssr, ES_REG(ensoniq, STATUS));
|
||||
synchronize_irq(ensoniq->irq);
|
||||
|
||||
snd_ensoniq_chip_init(ensoniq);
|
||||
|
||||
if ((err = snd_device_new(card, SNDRV_DEV_LOWLEVEL, ensoniq, &ops)) < 0) {
|
||||
snd_ensoniq_free(ensoniq);
|
||||
|
|
@ -2063,6 +2132,8 @@ static int __devinit snd_ensoniq_create(snd_card_t * card,
|
|||
|
||||
snd_ensoniq_proc_init(ensoniq);
|
||||
|
||||
snd_card_set_pm_callback(card, snd_ensoniq_suspend, snd_ensoniq_resume, ensoniq);
|
||||
|
||||
snd_card_set_dev(card, &pci->dev);
|
||||
|
||||
*rensoniq = ensoniq;
|
||||
|
|
@ -2389,6 +2460,7 @@ static struct pci_driver driver = {
|
|||
.id_table = snd_audiopci_ids,
|
||||
.probe = snd_audiopci_probe,
|
||||
.remove = __devexit_p(snd_audiopci_remove),
|
||||
SND_PCI_PM_CALLBACKS
|
||||
};
|
||||
|
||||
static int __init alsa_card_ens137x_init(void)
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user