When the Linux kernel is compiled with CONFIG_DEBUG_SHIRQ=y,
the Soundblaster Audigy2 ZS Notebook PCMCIA card causes the
system hang during boot (udev stage) or when the card is hot-plug.
The CONFIG_DEBUG_SHIRQ flag is by default 'y' with all Fedora
kernels since 2.6.23. The problem was reported as
https://bugzilla.redhat.com/show_bug.cgi?id=326411
The issue was hunted down to the snd_emu10k1_create() routine:
/* pseudo-code */
snd_emu10k1_create(...) {
...
request_irq(... IRQF_SHARED ...) {
register the irq handler
#ifdef CONFIG_DEBUG_SHIRQ
call the irq handler: snd_emu10k1_interrupt() {
poll I/O port // <---- !! system hangs
...
}
#endif
}
...
snd_emu10k1_cardbus_init(...) {
initialize I/O ports
}
...
}
The early access to I/O port in the interrupt handler causes
the freeze. Obviously it is necessary to init the I/O ports
before accessing them. This patch moves the registration of
the irq handler after the initialization of the I/O ports.
Signed-off-by: Jaroslav Franek <jarin.franek@post.cz>
Acked-by: James Courtier-Dutton <James@superbug.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fairly simple. "dev_use" was being allocated as a zero length array
because of bad math on 64-bit systems, causing a crash in
find_first_zero_bit(). One-liner follows:
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Fix divide by zero error in build_clear_page() and build_copy_page()
[MIPS] Fix typo in header guard
[MIPS] Fix build error - Delete debugging crap that crept in with CMP
[MIPS] Add accessors for random register.
[MIPS] IP27: misc fixes
[MIPS] IP27: Fix clockevent setup
[MIPS] IP27: Fix bootmem memory setup
[MIPS] remove CONFIG_CPU_R4000 line from Makefile
[MIPS] Fix check for valid stack pointer during backtrace
[MIPS] Add missing braces to pte_mkyoung
[MIPS] R4700: Fix build_tlb_probe_entry
[MIPS] Alchemy: dbdma: add API to delete custom DDMA device ids.
[MIPS] Alchemy: export get_au1x00_speed for modules
Previously, one would have to specifically choose CONFIG_OLPC and
CONFIG_PCI_GOOLPC in order to enable PCI_OLPC. That doesn't really work
for distro kernels, so this patch allows one to choose CONFIG_OLPC and
CONFIG_PCI_GOANY in order to build in OLPC support in a generic kernel (as
requested by Robert Millan).
This also moves GOOLPC before GOANY in the menuconfig list.
Finally, make pci_access_init return early if we detect OLPC hardware.
There's no need to continue probing stuff, and pci_pcbios_init
specifically trashes our settings (we didn't run into that before because
PCI_GOANY wasn't supported).
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Suggest how to deal with patch modifications caused by
merging or back-porting when you're a maintainer.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Don't trust a length which is greater than the working buffer.
An invalid length could cause overflow when calculating buffer size
for decoding oid.
- An oid length of zero is invalid and allows for an off-by-one error when
decoding oid because the first subid actually encodes first 2 subids.
- A primitive encoding may not have an indefinite length.
Thanks to Wei Wang from McAfee for report.
Cc: Steven French <sfrench@us.ibm.com>
Cc: stable@kernel.org
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alias brd to rd in the hope of helping legacy users. Suggested by Jan.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is an attempt to translate the prompt and help text into something
which is legible and, as a bonus, correct.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ip_fast_csum() requires a memory clobber on its inline asm as it accesses
memory in a fashion that gcc can't predict.
The GCC manual says:
If your assembler instructions access memory in an unpredictable
fashion, add `memory' to the list of clobbered registers. This will
cause GCC to not keep memory values cached in registers across the
assembler instruction and not optimize stores or loads to that memory.
The bug hasn't been noticed in FRV, but it has been seen in PA-RISC.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to reserve "unset" resources. Trying to reserve
them results in messages like this, which are ugly but harmless:
system 00:08: iomem range 0x0-0x0 could not be reserved
Future PNP patches will remove use of IORESOURCE_UNSET, but
we still need it for now.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes in the generic bootmem code broke memory setup for IP27. This
patch fixes this by replacing lots of special IP27 code with generic
bootmon code. This has been tested only on a single node.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The existing options are named CONFIG_CPU_R4300 and CONFIG_CPU_R4X00,
and they are directly below.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The newly added check for valid stack pointer address breaks at least for
64bit kernels. Use __get_user() for accessing stack content to avoid crashes,
when doing the backtrace.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only the version pte_mkyoung for 36-bit pagetables on 32-bit hw was
affected and with this bug being around since November 29, 2004 there
is evidence to suport the assumption it was benign ;-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Treat R4700 like R4600 in build_tlb_probe_entry. Without this fix kernel
will lock up.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add API to delete custom DDMA device ids create with
au1xxx_ddma_device_add().
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xmmc.c driver depends on it, so export it for modules.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check that tda827x_config is defined before attempting to use it.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the TDA18271HD/C1, we perform RF tracking filter correction for VHF low
band, only. If supplied a frequency out of range, the error must be returned
to the caller (tda18271c1_rf_tracking_filter_calibration) so that it can
decide whether or not to write to register EB14, RFC_CPROG[7:0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Testing whether xceive_pin is non-zero is not good enough as 0 is a valid
value. Instead explicitly test whether the Xceive tuner is used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is patch for fix data structure in querycap syscall.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-tip testing found the following build failure:
LD .tmp_vmlinux1
drivers/built-in.o: In function `generic_set_freq':
tuner-xc2028.c:(.text+0xbd896): undefined reference to `request_firmware'
tuner-xc2028.c:(.text+0xbdd7a): undefined reference to `release_firmware'
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0xc68e6): undefined reference to `request_firmware'
xc5000.c:(.text+0xc6abe): undefined reference to `release_firmware'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_18_11_34_CEST_2008.bad
the reason is another kconfig tool bug that has to be worked around in
the driver's Kconfig file: if FW_LOADER is selected in a second
dependency, that is not properly propagated up the dependencies.
in this case, FW_LOADER is selected from MEDIA_TUNER_XC2028:
config MEDIA_TUNER_XC2028
tristate "XCeive xc2028/xc3028 tuners"
depends on VIDEO_MEDIA && I2C
depends on HOTPLUG
select FW_LOADER
which got selected by MEDIA_TUNER:
config MEDIA_TUNER
tristate
default VIDEO_MEDIA && I2C
depends on VIDEO_MEDIA && I2C
select FW_LOADER if !MEDIA_TUNER_CUSTOMIZE && HOTPLUG
but the kconfig tool did not pick up this second-order dependency and
allowed CONFIG_FW_LOADER=m to be selected - in which case the build
fails.
the workaround i found was to move the select of FW_LOADER one level up,
so that the buggy kconfig tool can notice it and can act appropriately.
This problem can probably be worked around in other ways as well, i went
for the minimal fix.
Obviously, the kconfig tool should be fixed, it is not reasonable to
expect driver authors to do manual dependency resolution (that kconfig
itself already does) and uglify the Kconfig files. The kconfig tool did
nothing to warn about this situation and did not prevent this faulty
.config from being constructed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
