This patch causes vcc_release_async to be applied to any open
vcc's when the modem is disconnected. This signals a socket
shutdown, letting the socket user know that the game is up.
I wrote this patch because of reports that pppd would keep
connections open forever when the modem is disconnected.
This patch does not fix that problem, but it's a step in the
right direction. It doesn't help because the pppoatm module
doesn't yet monitor state changes on the ATM socket, so simply
never realises that the ATM connection has gone down (meaning
it doesn't tell the ppp layer). But at least there is a socket
state change now. Unfortunately this patch may create problems
for those rare users like me who use routed IP or some other
non-ppp connection method that goes via the ATM ARP daemon: the
daemon is buggy, and with this patch will crash when the modem
is disconnected. Users with a buggy atmarpd can simply restart
it after disconnecting the modem.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xusbatm driver is for otherwise unsupported modems.
All it does is grab hold of a user-specified set of
interfaces - the generic usbatm core methods (hopefully)
do the rest. As Aurelio Arroyo discovered when he tried
to use xusbatm (big mistake!), the interface grabbing logic
was completely borked. Here is a rewrite that works.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Have minidrivers and the core signal special requirements
using a flags field in struct usbatm_data. For the moment
this is only used to replace the need_heavy_init bind
parameter, but there'll be new flags in later patches.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch adds four new device IDs for the CP2101 driver.
Also 3 tab characters have been removed from device ID table.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for CA-42 clone cable (www.ca-42.com)
Signed-off-by: Martin Gingras <martin.gingras@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the URB initialisation for transfers
like this is done in other drivers too.
Without this patch no data was transmitted on a PXA270 OHCI
platform. May apply to others too.
Signed-off-by: Juergen Schindele <schindele@nentec.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the 0G0 Cable Ethernet device as reported by
Charles Lepple <clepple@gmail.com>.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been offered a nice Sony DSC-T5 digital camera, with a USB connection.
Unfortunately it is not recognized by Linux 2.6.14.4's usb-storage.
With the following change I'm able to mount and read my pictures:
Signed-off-by: Phil Dibowitz <phil@ipom.com>
this fixes
-potential hang by disconnecting through usbfs
-kzalloc
-general cleanup
-micro optimisation in interrupt handlers
It compiles and I am printing.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch from Bob Copeland adds support for the Rio Karma portable
digital audio player to the usb-storage driver. The only thing needed to
support this device is a one-time (per plugin) init command which is sent
to the device.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should fix things mentioned below:
"I was curious why my firewall was loading a 'phone driver'.
It turns out that the probing in the yealink driver is
a little too assuming..
static struct usb_device_id usb_table [] = {
{ USB_INTERFACE_INFO(USB_CLASS_HID, 0, 0) },
{ }
};
So it picked up my UPS, and loaded the driver.
Whilst no harm came, because it later checks the vendor/product IDs,
this driver should probably be rewritten to only probe
for the device IDs it actually knows about.
Dave"
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation: Specify grayscale specification on ATIK-ATK16
and ATIK-ATK16HR comments.
New: Add ProductID and VendorID for devices ATIK-ATK16C and
ATIK-ATK16HRC. These devices are also USB Astronomical CCD
cameras that work through an FTDI 245BM chip, share the
same base hardware but, it has a colour CCD chip instead
of a grayscale one.
Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch adds a new PID for the ftdi_sio driver. It will
enable support for PC-DJ's DAC-2 controller module
(more information on http://www.pcdjhardware.com/DAC2.asp)
Signed-off-by: Wouter Paesen <wouter@kangaroot.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Cory Lee to support two POS
printers made by Westrex International (Model 777 and Model 8900F).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch includes the Vendor Id for a optic fiber to USB device named
TTUSB from thought Technology. It's just add the vendor Id to
ftdi_sio.h and add the Vendor ID and model Id to table_combined.
Signed-off-by: Louis Nyffenegger <louis.nyffenegger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the previously widely-used ehci-pci.c BIOS handoff
code into the pci-quirks.c file, replacing the less widely used
"early handoff" version that seems to cause problems lately.
One notable change: the "early handoff" version always enabled
an SMI IRQ ... and did so even if the pre-Linux code said it was
not using EHCI (and not expecting EHCI SMIs). Looks like a goof
in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux
code says it's using EHCI. And now it always forces them off "just
in case".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tmp_buf_sem sems to be a common name for something completely unused...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> ("usb portion")
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements support for the fn key on Apple PowerBooks using
USB based keyboards and makes them behave like their ADB counterparts.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Rene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Cherry Cymotion is a special Linux keyboard made by Cherry, with
only one little problem: it doesn't work with Linux. This patch
(originally by hexten.net, cleaned up by me) makes it work including
all the special keys.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
USB gadget drivers make no use of these, remove the pointless
comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Here's a small patch with a few tiny fixups for the EHCI Kconfig help
text. Please consider applying.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This moves the 32 bit ioctl compatibility handlers for
Video4Linux into a new file and adds explicit calls to them
to each v4l device driver.
Unfortunately, there does not seem to be any code handling
the v4l2 ioctls, so quite often the code goes through two
separate conversions, first from 32 bit v4l to 64 bit v4l,
and from there to 64 bit v4l2. My patch does not change
that, so there is still much room for improvement.
Also, some drivers have additional ioctl numbers, for
which the conversion should be handled internally to
that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Some long time ago, dentry struct was carefully tuned so that on 32 bits
UP, sizeof(struct dentry) was exactly 128, ie a power of 2, and a multiple
of memory cache lines.
Then RCU was added and dentry struct enlarged by two pointers, with nice
results for SMP, but not so good on UP, because breaking the above tuning
(128 + 8 = 136 bytes)
This patch reverts this unwanted side effect, by using an union (d_u),
where d_rcu and d_child are placed so that these two fields can share their
memory needs.
At the time d_free() is called (and d_rcu is really used), d_child is known
to be empty and not touched by the dentry freeing.
Lockless lookups only access d_name, d_parent, d_lock, d_op, d_flags (so
the previous content of d_child is not needed if said dentry was unhashed
but still accessed by a CPU because of RCU constraints)
As dentry cache easily contains millions of entries, a size reduction is
worth the extra complexity of the ugly C union.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Paul Jackson <pj@sgi.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@epoch.ncsc.mil>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers/media/video and usb/media drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
