Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl: Return non-zero on error in probe()
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
libata: New driver for OCTEON SOC Compact Flash interface (v7).
libata: Add another column to the ata_timing table.
sata_via: Add VT8261 support
pata_atiixp: update port enabledness test handling
[libata] get-identity ioctl: Fix use of invalid memory pointer
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
Impact: fix 15 make headers_check warnings:
include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike other alphas, marvel doesn't have real PC-style CMOS clock hardware
- RTC accesses are emulated via PAL calls. Unfortunately, for unknown
reason these calls work only on CPU #0. So current implementation for
arbitrary CPU makes CMOS_READ/WRITE to be executed on CPU #0 via IPI.
However, for obvious reason this doesn't work with standard
get/set_rtc_time() functions, where a bunch of CMOS accesses is done with
disabled interrupts.
Solved by making the IPI calls for entire get/set_rtc_time() functions,
not for individual CMOS accesses. Which is also a lot more effective
performance-wise.
The patch is largely based on the code from Jay Estabrook.
My changes:
- tweak asm-generic/rtc.h by adding a couple of #defines to
avoid a massive code duplication in arch/alpha/include/asm/rtc.h;
- sys_marvel.c: fix get/set_rtc_time() return values (Jay's FIXMEs).
NOTE: this fixes *only* LIB_RTC drivers. Legacy (CONFIG_RTC) driver
wont't work on marvel. Actually I think that we should just disable
CONFIG_RTC on alpha (maybe in 2.6.30?), like most other arches - AFAIK,
all modern distributions use LIB_RTC anyway.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the standard magic.h for btrfs and squashfs.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix __request_region() parameter kernel-doc notation and parameter name:
Warning(linux-2.6.28-git10//kernel/resource.c:627): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix jbd header file kernel-doc notation:
Warning(linux-2.6.28-git13//include/linux/jbd.h:823): No description found for parameter 'j_average_commit_time'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds an init_dummy_netdev() function that gets a network device
structure (allocation and lifetime entirely under caller's control) and
initialize the minimum amount of fields so it can be used to schedule
NAPI polls without registering a full blown interface. This is to be
used by drivers that need to tie several hardware interfaces to a single
NAPI poll scheduler due to HW limitations.
It also updates the ibm_newemac driver to use that, this fixing the
oops on 2.6.29 due to passing NULL as "dev" to netif_napi_add()
Symbol is exported GPL only a I don't think we want binary drivers doing
that sort of acrobatics (if we want them at all).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/83xx: Move mcu_mpc8349emitx driver out of drivers/i2c/chips/
powerpc/83xx: Make serial ports work on MPC8315E-RDB w/ FSL U-Boots
powerpc/e500mc: Doorbells need to be taken w/exceptions disabled
powerpc: Enable PS3 options and QPACE in ppc64_defconfig
powerpc/powermac: Fix occasional SMP boot failure
powerpc/cacheinfo: Rename cache_dir per-cpu variable
hvc_console: Use kzalloc() instead of kmalloc() + memset()
hvc_console: Do not set low_latency when using interrupts
hvc_console: Call free_irq() only if request_irq() was successful
hvc_console: Change an mb() to smp_mb() and add some comments
powerpc: Cleanup from l64 to ll64 change: drivers/net
powerpc: Cleanup from l64 to ll64 change: drivers/char
powerpc: Cleanup from l64 to ll64 change: arch code
powerpc: Change u64/s64 to a long long integer type
powerpc/kexec: Check crash_base for relocatable kernel
powerpc: Make dummy section a valid note header
Xilinx: SPI: updated driver for device tree
drivers/of: Add the of_find_i2c_device_by_node function.
powerpc/xsysace: add compatible string for non-ipcore instance
powerpc/mpc52xx: remove dead code from GPIO driver
...
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
IDE: fix sparse signed-ness errors with host->host_busy
ide: fix suspend regression
tx4938ide: Fix build error due to read_sff_dma_status moving
ide: remove unused CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
sl82c105: remove dead code
via82cxxx: fix cable warning message
ide: can't use SSD/non-rotational queue flag for all CFA devices
it821x.c: use dev->revision instead of pci_read_config_byte
it821x: Add ultra_mask quirk for Vortex86SX
ide: fix accidental LOCKDEP breakage caused by local_irq_set() removal
The host_busy field in struct ide_host defaults to a
signed-long, where most arch's test_and_set_bit_*
macros use an unsigned long.
Change to using an unsigned long, which on ARM removes
the following sparse errors:
drivers/ide/ide-io.c:681:8: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:681:8: expected unsigned long volatile *p
drivers/ide/ide-io.c:681:8: got long volatile *<noident>
drivers/ide/ide-io.c:681:8: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:681:8: expected unsigned long volatile *p
drivers/ide/ide-io.c:681:8: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
drivers/ide/ide-io.c:695:3: warning: incorrect type in argument 2 (different signedness)
drivers/ide/ide-io.c:695:3: expected unsigned long volatile *p
drivers/ide/ide-io.c:695:3: got long volatile *<noident>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Vortex86SX with IDE controller revision 0x11 ultra DMA must be
disabled. This patch was tested by DMP and seems to work.
It is a cleaned up version of their older Kernel patch:
http://www.dmp.com.tw/tech/vortex86sx/patch-2.6.24-DMP.gz
Tested-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This assertion is incorrect for lockless pagecache. By definition if we
have an unpinned page that we are trying to take a speculative reference
to, it may become the tail of a compound page at any time (if it is
freed, then reallocated as a compound page).
It was still a valid assertion for the vmscan.c LRU isolation case, but
it doesn't seem incredibly helpful... if somebody wants it, they can
put it back directly where it applies in the vmscan code.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This enables the use of syscall wrappers to do proper sign extension
for 64-bit programs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Martin Schwidefsky <schwidefsky@de.ibm.com>
By selecting HAVE_SYSCALL_WRAPPERS architectures can activate
system call wrappers in order to sign extend system call arguments.
All architectures where the ABI defines that the caller of a function
has to perform sign extension probably need this.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Convert all system calls to return a long. This should be a NOP since all
converted types should have the same size anyway.
With the exception of sys_exit_group which returned void. But that doesn't
matter since the system call doesn't return.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Impact: cleanup
Change the protection parameter for track_pfn_vma_new() into a pgprot_t pointer.
Subsequent patch changes the x86 PAT handling to return a compatible
memtype in pgprot_t, if what was requested cannot be allowed due to conflicts.
No fuctionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
virt_to_page() call should not be used on kernel text and data
addresses. virt_to_page() is used by sg_init_one(). So change padbuf
to be allocated within iscsi_segment.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
reorder struct xt_match to remove 8 bytes of padding and make its size
128 bytes.
This saves a small amount of data space in each of the xt netfilter
modules and fits xt_match in one 128 byte cache line.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparc64: Fix cpumask related build failure
smp_call_function_single(): be slightly less stupid, fix
smp_call_function_single(): be slightly less stupid
rcu: fix bug in rcutorture system-shutdown code
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
ucc_geth: use correct UCCE macros
net_dma: acquire/release dma channels on ifup/ifdown
cxgb3: Keep LRO off if disabled when interface is down
sfc: SFT9001: Fix condition for LNPGA power-off
dccp ccid-3: Fix RFC reference
smsc911x: register irq with device name, not driver name
smsc911x: fix smsc911x_reg_read compiler warning
forcedeth: napi schedule lock fix
net: fix section mismatch warnings in dccp/ccids/lib/tfrc.c
forcedeth: remove mgmt unit for mcp79 chipset
qlge: Remove dynamic alloc of rx ring control blocks.
qlge: Fix schedule while atomic issue.
qlge: Remove support for device ID 8000.
qlge: Get rid of split addresses in hardware control blocks.
qlge: Get rid of volatile usage for shadow register.
forcedeth: version bump and copyright
forcedeth: xmit lock fix
netdev: missing validate_address hooks
netdev: add missing set_mac_address hook
netdev: gianfar: add MII ioctl handler
...
* 'for_2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6:
Fix small typo
misdn: indentation and braces disagree - add braces
misdn: one handmade ARRAY_SIZE converted
drivers/isdn/hardware/mISDN: move a dereference below a NULL test
indentation & braces disagree - add braces
Make parameter debug writable
BUGFIX: used NULL pointer at ioctl(sk,IMGETDEVINFO,&devinfo) when devinfo.id not registered
warning: ignoring return value of 'device_register', declared with attribute
warn_unused_result
warning: ignoring return value of 'device_create_file', declared with
attribute warn_unused_result
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The recent dmaengine rework removed the capability to remove dma device
driver modules while net_dma is active. Rather than notify
dmaengine-clients that channels are trying to be removed, we now rely on
clients to notify dmaengine when they no longer have a need for
channels. Teach net_dma to release channels by taking dmaengine
references at netdevice open and dropping references at netdevice close.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel-doc was referring to member @debufs_dentry instead of
@debugfs_dentry.
Reported by Randy Dunlap http://marc.info/?l=linux-netdev&m=123147942302885&w=2
As well, escape the colon in the field's text description, as it is
causing the generated text to be erraticly broken up (with paragraphs
moved down). Could not find a reason why it is happening so, even when
other field descriptions use colons and work as expected.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you do
smp_call_function_single(expression-with-side-effects, ...)
then expression-with-side-effects never gets evaluated on UP builds.
As always, implementing it in C is the correct thing to do.
While we're there, uninline it for size and possible header dependency
reasons.
And create a new kernel/up.c, as a place in which to put
uniprocessor-specific code and storage. It should mirror kernel/smp.c.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changes from V1:
- Removed support for suspend_enable & suspend_disable functions.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
