This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff8cbf250b ("xhci: clear root port wake on bits if controller isn't")
can cause device detection error if runtime PM is enabled, and S3 wake
is disabled. Revert it.
https://bugzilla.kernel.org/show_bug.cgi?id=85701
This commit got into stable and should be reverted from there as well.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reported-by: Dmitry Nezhevenko <dion@inhex.net>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Cc: <stable@vger.kernel.org> #v2.6.35
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly, so we need to fall-back to usb-storage for these.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three fixes for bugs related to TTY error reporting, which can to lead
to data being dropped by the line discipline.
Included is also some new device ids for ftdi_sio and cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aEjf
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc6
Three fixes for bugs related to TTY error reporting, which can to lead
to data being dropped by the line discipline.
Included is also some new device ids for ftdi_sio and cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes: 6b8f1ca558 ("USB: ssu100: set tty_flags in ssu100_process_packet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reporting of overrun errors, which are not associated with a
character. Instead insert a null character and report only once.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PIDs for new Matrix Orbital GTT series products.
Signed-off-by: Troy Clark <tclark@matrixorbital.ca>
Cc: stable <stable@vger.kernel.org>
[johan: shorten commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit 0943d8ead3 ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable <stable@vger.kernel.org> # v3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=egWd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QlS+
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc4
Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to only raise DTR on transitions from B0 in set_termios.
Also allow set_termios to be called from open with a termios_old of
NULL. Note that DTR will not be raised prematurely in this case.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bda9893c50 as it was
incorrect.
Reported-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 0d930e51cf ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
These updates remove two allocations of unused buffers from kobil_sct
and add some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PSiW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc3
These updates remove two allocations of unused buffers from kobil_sct
and add some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Excessive debug messages might cause timing issues that prevent correct
usb enumeration. This patch hides information about USB bus reset to let
driver enumerate fast enough to avoid making host angry. This fixes
endless enumeration and usb reset loop observed with some Linux hosts.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The call of 'kfree(ci->hw_bank.regmap)' in ci_hdrc_remove() sometimes causes
a kernel oops when removing the ci_hdrc module.
Since there is no separate memory allocated for the ci->hw_bank.regmap array,
there is no need to free it.
Cc: v3.14+ <stable@@vger.kernel.org>
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed the return value on failure. status variable
is set to 0 at usb_assign_descriptors call and the same is
returned on error which is incorrect.
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes probe function to match the pattern used elsewhere in
the driver, where power regulators are turned off as the last element in
the device shutdown procedure.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed usb_free_all_descriptors in the bind functions, which
results in double-free corruption of the descriptors on error path.
The usb descriptors are allocated by usb_assign_descriptors.
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_stop() should clear ->driver pointer unconditionally to let the UDC
framework to work correctly with both registering/unregistering gadgets
and enabling/disabling gadgets by writing to
/sys/class/udc/*hsotg/soft_connect interface.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The unioned u32 is used for clearing etc. Having the number of
bitfield bits add up to more than 32 is broken, even if benign.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse was giving the following warning:
warning: context imbalance in 's3c_hsotg_ep_enable'
- different lock contexts for basic block
we were returning ENOMEM while still holding the spinlock.
The sparse warning was fixed by releasing the spinlock before return.
Cc: <stable@vger.kernel.org> # v3.17
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in
|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
echo mem > /sys/power/state
then you go boom
|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)
because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 468bcc2a2c ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a2c "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
