Changes to CM to support CM and port redirection (REJ reason 24).
Signed-off-by: John Kingman <kingman <at> storagegear.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Most awkward part of this is delaying write requests until bitmap updates have
been flushed.
To achieve this, we have a sequence number (seq_flush) which is incremented
each time the raid5 is unplugged.
If the raid thread notices that this has changed, it flushes bitmap changes,
and assigned the value of seq_flush to seq_write.
When a write request arrives, it is given the number from seq_write, and that
write request may not complete until seq_flush is larger than the saved seq
number.
We have a new queue for storing stripes which are waiting for a bitmap flush
and an extra flag for stripes to record if the write was 'degraded' and so
should not clear the a bit in the bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
version-1 superblocks are not (normally) 4K long, and can be of variable size.
Writing the full 4K can cause corruption (but only in non-default
configurations).
With this patch the super-block-flavour can choose a size to read, and set a
size to write based on what it finds.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These inlines haven't been used for ages, they should go.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As this is used to flag an internal bitmap.
Also, introduce symbolic names for feature bits.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
linear currently uses division by the size of the smallest componenet device
to find which device a request goes to. If that smallest device is larger
than 2 terabytes, then the division will not work on some systems.
So we introduce a pre-shift, and take care not to make the hash table too
large, much like the code in raid0.
Also get rid of conf->nr_zones, which is not needed.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a device is flagged 'WriteMostly' and the array has a bitmap, and the
bitmap superblock indicates that write_behind is allowed, then write_behind is
enabled for WriteMostly devices.
Write requests will be acknowledges as complete to the caller (via b_end_io)
when all non-WriteMostly devices have completed the write, but will not be
cleared from the bitmap until all devices complete.
This requires memory allocation to make a local copy of the data being
written. If there is insufficient memory, then we fall-back on normal write
semantics.
Signed-Off-By: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows a device in a raid1 to be marked as "write mostly". Read requests
will only be sent if there is no other option.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Both file-bitmaps and superblock bitmaps are supported.
If you add a bitmap file on the array device, you lose.
This introduces a 'default_bitmap_offset' field in mddev, as the ioctl used
for adding a superblock bitmap doesn't have room for giving an offset. Later,
this value will be setable via sysfs.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
completion events after destroying a CQ, QP or SRQ. We do this by
sweeping the event lists before returning from a destroy calls, and
then return the number of events already reported before the destroy
call. This allows userspace wait until it has processed all events
for an object returned from the kernel before it frees its context for
the object.
The ABI of the destroy CQ, destroy QP and destroy SRQ commands has to
change to return the event count, so bump the ABI version from 1 to 2.
The userspace libibverbs library has already been updated to handle
both the old and new ABI versions.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add structure definition for ClassPortInfo format. This is
needed for (at least) handling CM redirects.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't just irritate all other kernel developers. Fix the users first,
then you can re-introduce the must-check infrastructure to avoid new
cases creeping in.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SA: Move SA attributes to ib_sa.h so are accessible to more than
sa_query.c. Also, remove deprecated attributes and add one missing one.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new FSYNCDIR request, which is sent when fsync is called
on directories. This operation is available in libfuse 2.3-pre1 or
greater.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make data caching behavior selectable on a per-open basis instead of
per-mount. Compatibility for the old mount options 'kernel_cache' and
'direct_io' is retained in the userspace library (version 2.4.0-pre1 or
later).
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes a long lasting "hack" in FUSE, which used a separate
channel (a file descriptor refering to a disk-file) to transfer directory
contents from userspace to the kernel.
The patch adds three new operations (OPENDIR, READDIR, RELEASEDIR), which
have semantics and implementation exactly maching the respective file
operations (OPEN, READ, RELEASE).
This simplifies the directory reading code. Also disk space is not
necessary, which can be important in embedded systems.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add padding to structures to make sizes the same on 32bit and 64bit archs.
Initial testing and test machine generously provided by Franco Broi.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the extended attribute operations to FUSE.
The following operations are added:
o getxattr
o setxattr
o listxattr
o removexattr
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the file operations of FUSE.
The following operations are added:
o open
o flush
o release
o fsync
o readpage
o commit_write
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the write filesystem operations of FUSE.
The following operations are added:
o setattr
o symlink
o mknod
o mkdir
o create
o unlink
o rmdir
o rename
o link
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the read-only filesystem operations of FUSE.
This contains the following files:
o dir.c
- directory, symlink and file-inode operations
The following operations are added:
o lookup
o getattr
o readlink
o follow_link
o directory open
o readdir
o directory release
o permission
o dentry revalidate
o statfs
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the FUSE device handling functions.
This contains the following files:
o dev.c
- fuse device operations (read, write, release, poll)
- registers misc device
- support for sending requests to userspace
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds FUSE core.
This contains the following files:
o inode.c
- superblock operations (alloc_inode, destroy_inode, read_inode,
clear_inode, put_super, show_options)
- registers FUSE filesystem
o fuse_i.h
- private header file
Requirements
============
The most important difference between orinary filesystems and FUSE is
the fact, that the filesystem data/metadata is provided by a userspace
process run with the privileges of the mount "owner" instead of the
kernel, or some remote entity usually running with elevated
privileges.
The security implication of this is that a non-privileged user must
not be able to use this capability to compromise the system. Obvious
requirements arising from this are:
- mount owner should not be able to get elevated privileges with the
help of the mounted filesystem
- mount owner should not be able to induce undesired behavior in
other users' or the super user's processes
- mount owner should not get illegitimate access to information from
other users' and the super user's processes
These are currently ensured with the following constraints:
1) mount is only allowed to directory or file which the mount owner
can modify without limitation (write access + no sticky bit for
directories)
2) nosuid,nodev mount options are forced
3) any process running with fsuid different from the owner is denied
all access to the filesystem
1) and 2) are ensured by the "fusermount" mount utility which is a
setuid root application doing the actual mount operation.
3) is ensured by a check in the permission() method in kernel
I started thinking about doing 3) in a different way because Christoph
H. made a big deal out of it, saying that FUSE is unacceptable into
mainline in this form.
The suggested use of private namespaces would be OK, but in their
current form have many limitations that make their use impractical (as
discussed in this thread).
Suggested improvements that would address these limitations:
- implement shared subtrees
- allow a process to join an existing namespace (make namespaces
first-class objects)
- implement the namespace creation/joining in a PAM module
With all that in place the check of owner against current->fsuid may
be removed from the FUSE kernel module, without compromising the
security requirements.
Suid programs still interesting questions, since they get access even
to the private namespace causing some information leak (exact
order/timing of filesystem operations performed), giving some
ptrace-like capabilities to unprivileged users. BTW this problem is
not strictly limited to the namespace approach, since suid programs
setting fsuid and accessing users' files will succeed with the current
approach too.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes a macro definition so that kernel-doc can understand it.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This set of two patches add support for the framebuffer of the Samsung S3C2410
ARM SoC. This driver was started about one year ago and is now used on iPAQ
h1930/h1940, Acer n30 and probably other s3c2410-based machines I'm not aware
of. I've also heard yesterday that it's working also on iPAQ rx3715/rx3115
(s3c2440-based machines).
Signed-Off-By: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Ben Dooks <ben@trinity.fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function bit_putcs() in drivers/video/console/bitblit.c is becoming large.
Break it up into its component functions (bit_putcs_unaligned and
bit_putcs_aligned).
Incorporated fb_pad_aligned_buffer() optimization by Roman Zippel.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To solve touchscreen interference problems devices like the Sharp Zaurus
SL-C3000 need to know the length of the horitzontal sync pulses. This patch
adds a hook to pxafb so the touchscreen driver can function correctly.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Coordinated Video Timings (CVT) is the latest standard approved by VESA
concerning video timings generation. It addresses the limitation of GTF which
is designed mainly for CRT displays. CRT's have a high blanking requirement
(as much as 25% of the horizontal frame length) which artificially increases
the pixelclock. Digital displays, on the other hand, needs to conserve the
pixelclock as much as possible. The GTF also does not take into account the
different aspect ratios in its calculation.
The new function added is fb_find_mode_cvt(). It is called by fb_find_mode()
if it recognizes a mode option string formatted for CVT. The format is:
<xres>x<yres>[M][R][-<bpp>][<at-sign><refresh>][i][m]
The 'M' tells the function to calculate using CVT. On it's own, it will
compute a timing for CRT displays at 60Hz. If the 'R' is specified, 'reduced
blanking' computation will be used, best for flatpanels. The 'i' and the 'm'
is for 'interlaced mode' and 'with margins' respectively.
To determine if CVT was used, check for dmesg for something like this:
CVT Mode - <pix>M<n>[-R], ie: .480M3-R (800x600 reduced blanking)
where: pix - product of xres and yres, in MB
M - is a CVT mode
n - the aspect ratio (3 - 4:3; 4 - 5:4; 9 - 16:9, 15:9; A - 16:10)
-R - reduced blanking
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some small rearrangements of the PCI probing code in
order to make it possible for arch code to set up the PCI tree
without needing to duplicate code from the PCI layer unnecessarily.
PPC64 will use this to set up the PCI tree from the Open Firmware
device tree, which we need to do on logically-partitioned pSeries
systems.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a framebuffer driver for the Cyberblade/i1 graphics core.
Currently tridenfb claims to support the cyberblade/i1 graphics core. This
is of very limited truth. Even vesafb is faster and provides more working
modes and a much better quality of the video signal. There is a great
number of bugs in tridentfb ... but most often it is impossible to decide
if these bugs are real bugs or if fixing them for the cyberblade/i1 core
would break support for one of the other supported chips.
Tridentfb seems to be unmaintained,and documentation for most of the
supported chips is not available. So "fixing" cyberblade/i1 support inside
of tridentfb was not an option, it would have caused numerous
if(CYBERBLADEi1) else ... cases and would have rendered the code to be
almost unmaintainable.
A first version of this driver was published on 2005-07-31. A fix for a
bug reported by Jochen Hein was integrated as well as some changes
requested by Antonino A. Daplas.
A message has been added to tridentfb to inform current users of tridentfb
to switch to cyblafb if the cyberblade/i1 graphics core is detected.
This patch is one logical change, but because of the included documentation
it is bigger than 70kb. Therefore it is not sent to lkml and
linux-fbdev-devel,
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lifts sisfb from version 1.7.17 to version 1.8.9. Changes include:
- Added support for XGI V3XT, V5, V8, Z7 chipsets, including POSTing of
all of these chipsets.
- Added support for latest SiS chipsets (761).
- Added support for SiS76x memory "hybrid" mode.
- Added support for new LCD resolutions (eg 1280x854, 856x480).
- Fixed support for 320x240 STN panels (for embedded devices).
- Fixed many HDTV modes (525p, 750p, 1080i).
- Fixed PCI config register reading/writing to use proper kernel
functions for this purpose.
- Fixed PCI ROM handling to use the kernel's proper functions.
- Removed lots of "typedef"s.
- Removed lots of code which was for X.org/XFree86 only.
- Fixed coding style in many places.
- Removed lots of 2.4 cruft.
- Reduced stack size by unifying two previously separate structs into
one.
- Added new hooks for memory allocation (for DRM). Now the driver can
truly handle multiple cards, including memory management.
- Fixed numerous minor bugs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, fbcon assumes that the visual FB_VISUAL_MONO* is always 1 bit.
According to Geert, there are old hardware where it's possible to have
monochrome at 8-bit, but has only 2 colors, black - 0x00 and white - 0xff.
Fix color handlers (fb_get_color_depth, and get_color) for this special case.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For the i386, code is already present in video.S that gets the EDID from the
video BIOS. Make this visible so drivers can also use this data as fallback
when i2c does not work.
To ensure that the EDID block is returned for the primary graphics adapter
only, by check if the IORESOURCE_ROM_SHADOW flag is set.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add rudimentary support by manipulating the VGA registers. However, not
all vesa modes are VGA compatible, so VGA compatiblity is checked first.
Only 2 levels are supported, powerup and powerdown.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add capability to fbdev to listen to the FB_ACTIVATE_ALL flag. If set, it
notifies fbcon that all consoles must be set to the current var.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch to eliminate struct files_struct.file_lock spinlock on the reader side
and use rcu refcounting rcuref_xxx api for the f_count refcounter. The
updates to the fdtable are done by allocating a new fdtable structure and
setting files->fdt to point to the new structure. The fdtable structure is
protected by RCU thereby allowing lock-free lookup. For fd arrays/sets that
are vmalloced, we use keventd to free them since RCU callbacks can't sleep. A
global list of fdtable to be freed is not scalable, so we use a per-cpu list.
If keventd is already handling the current cpu's work, we use a timer to defer
queueing of that work.
Since the last publication, this patch has been re-written to avoid using
explicit memory barriers and use rcu_assign_pointer(), rcu_dereference()
premitives instead. This required that the fd information is kept in a
separate structure (fdtable) and updated atomically.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for the RCU to work, the file table array, sets and their sizes must
be updated atomically. Instead of ensuring this through too many memory
barriers, we put the arrays and their sizes in a separate structure. This
patch takes the first step of putting the file table elements in a separate
structure fdtable that is embedded withing files_struct. It also changes all
the users to refer to the file table using files_fdtable() macro. Subsequent
applciation of RCU becomes easier after this.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a set of primitives to do reference counting for objects that are looked
up without locks using RCU.
Signed-off-by: Ravikiran Thirumalai <kiran_th@gmail.com>
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First of a number of files_lock scaability patches.
Here are the x86 numbers -
tiobench on a 4(8)-way (HT) P4 system on ramdisk :
(lockfree)
Test 2.6.10-vanilla Stdev 2.6.10-fd Stdev
-------------------------------------------------------------
Seqread 1400.8 11.52 1465.4 34.27
Randread 1594 8.86 2397.2 29.21
Seqwrite 242.72 3.47 238.46 6.53
Randwrite 445.74 9.15 446.4 9.75
The performance improvement is very significant.
We are getting killed by the cacheline bouncing of the files_struct
lock here. Writes on ramdisk (ext2) seems to vary just too
much to get any meaningful number.
Also, With Tridge's thread_perf test on a 4(8)-way (HT) P4 xeon system :
2.6.12-rc5-vanilla :
Running test 'readwrite' with 8 tasks
Threads 0.34 +/- 0.01 seconds
Processes 0.16 +/- 0.00 seconds
2.6.12-rc5-fd :
Running test 'readwrite' with 8 tasks
Threads 0.17 +/- 0.02 seconds
Processes 0.17 +/- 0.02 seconds
I repeated the measurements on ramfs (as opposed to ext2 on ramdisk in
the earlier measurement) and I got more consistent results from tiobench :
4(8) way xeon P4
-----------------
(lock-free)
Test 2.6.12-rc5 Stdev 2.6.12-rc5-fd Stdev
-------------------------------------------------------------
Seqread 1282 18.59 1343.6 26.37
Randread 1517 7 2415 34.27
Seqwrite 702.2 5.27 709.46 5.9
Randwrite 846.86 15.15 919.68 21.4
4-way ppc64
------------
(lock-free)
Test 2.6.12-rc5 Stdev 2.6.12-rc5-fd Stdev
-------------------------------------------------------------
Seqread 1549 91.16 1569.6 47.2
Randread 1473.6 25.11 1585.4 69.99
Seqwrite 1096.8 20.03 1136 29.61
Randwrite 1189.6 4.04 1275.2 32.96
Also running Tridge's thread_perf test on ppc64 :
2.6.12-rc5-vanilla
--------------------
Running test 'readwrite' with 4 tasks
Threads 0.20 +/- 0.02 seconds
Processes 0.16 +/- 0.01 seconds
2.6.12-rc5-fd
--------------------
Running test 'readwrite' with 4 tasks
Threads 0.18 +/- 0.04 seconds
Processes 0.16 +/- 0.01 seconds
The benefits are huge (upto ~60%) in some cases on x86 primarily
due to the atomic operations during acquisition of ->file_lock
and cache line bouncing in fast path. ppc64 benefits are modest
due to LL/SC based locking, but still statistically significant.
This patch:
RCU head initilizer no longer needs the head varible name since we don't use
list.h lists anymore.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Removed kernel version dependency from tea575x-tuner.h
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Include saa6588 compiler option and files.
- Fix comment on tuner.h
- linux/utsname.h replaced by linux/version.h to compile on vanilla 2.6.13
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove $Id CVS logs for V4L files
- Included newer cards.
- Added a new NEC protocol for ir based on pulse distance.
- Enable ATSC support for DViCO FusionHDTV5 Gold.
- Added tuner LG NTSC (TALN mini series).
- Fixed tea5767 autodetection.
- Resolve more tuner types.
- Commented debug function removed from mainstream.
- Remove comments from mainstream. Still on development tree.
- linux/version dependencies removed.
- BTSC Lang1 now is set to auto_stereo mode.
- New tuner standby API.
- i2c-core.c uses hexadecimal for the i2c address, so it should stay consistent.
Signed-off-by: Uli Luckas <luckas@musoft.de>
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a devname parameter to the pcmcia_device structure, fills it with
"pcmcia<bus_id>" in pcmcia_device_add, and passes it to request_irq in
pcmcia_request_irq.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Share code between setup-bus.c and yenta_socket.c: use the write-out code of
resources to the bridge also in yenta_socket.c, as it provides useful debug
output. In addition, it fixes the bug that the CPU-centric resource view
might need to be transferred to the PCI-centric view: setup-bus.c does that,
while yenta-socket.c did not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all #include <linux/version.h> and all references to LINUX_VERSION_CODE
and KERNEL_VERSION. Based on patch by Olaf Hering.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have a system (Biostar IDEQ210M mini-pc with a VIA chipset) which will
not reboot unless a keyboard is plugged in to it. I have tried all
combinations of the kernel "reboot=x,y" flags to no avail. Rebooting by
any method will leave the system in a wedged state (at the "Restarting
system" message).
I finally tracked the problem down to the machine's refusal to fully reboot
unless the keyboard controller status register had bit 2 set. This is the
"System flag" which when set, indicates successful completion of the
keyboard controller self-test (Basic Assurance Test, BAT).
I suppose that something is trying to protect against sporadic reboots
unless the keyboard controller is in a good state (a keyboard is present),
but I need this machine to be headless.
I found that setting the system flag (via the command byte) before giving
the "pulse reset line" command will allow the reboot to proceed. The patch
is simple, and I think it should be fine for everybody whether they have
this type of machine or not. This affects the "hard" reboot (as done when
the kernel boot flags "reboot=c,h" are used).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function prototype for handle_IRQ_event() in a few architctures is not
needed because they use GENERIC_HARDIRQ.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For architecture like ia64, the switch stack structure is fairly large
(currently 528 bytes). For context switch intensive application, we found
that significant amount of cache misses occurs in switch_to() function.
The following patch adds a hook in the schedule() function to prefetch
switch stack structure as soon as 'next' task is determined. This allows
maximum overlap in prefetch cache lines for that structure.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch changes the usages of PVR_440* into strcmp's with the
cpu_name field, and removes the defines altogether. The Ebony portion was
briefly tested long ago. One benefit of moving from PVR-tests to string
tests in general is that not all CPUs can be on and be able to do this type
of comparison.
See http://patchwork.ozlabs.org/linuxppc/patch?id=1250 for the original
thread.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the inode_post_link and inode_post_rename LSM hooks as
they are unused (and likely useless).
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the inode_post_create/mkdir/mknod/symlink LSM hooks as
they are obsoleted by the new inode_init_security hook that enables atomic
inode security labeling.
If anyone sees any reason to retain these hooks, please speak now. Also,
is anyone using the post_rename/link hooks; if not, those could also be
removed.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch set enables atomic security labeling of newly created
inodes by altering the fs code to invoke a new LSM hook to obtain the security
attribute to apply to a newly created inode and to set up the incore inode
security state during the inode creation transaction. This parallels the
existing processing for setting ACLs on newly created inodes. Otherwise, it
is possible for new inodes to be accessed by another thread via the dcache
prior to complete security setup (presently handled by the
post_create/mkdir/... LSM hooks in the VFS) and a newly created inode may be
left unlabeled on the disk in the event of a crash. SELinux presently works
around the issue by ensuring that the incore inode security label is
initialized to a special SID that is inaccessible to unprivileged processes
(in accordance with policy), thereby preventing inappropriate access but
potentially causing false denials on legitimate accesses. A simple test
program demonstrates such false denials on SELinux, and the patch solves the
problem. Similar such false denials have been encountered in real
applications.
This patch defines a new inode_init_security LSM hook to obtain the security
attribute to apply to a newly created inode and to set up the incore inode
security state for it, and adds a corresponding hook function implementation
to SELinux.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ib_sa.h: Define more SA methods (initially for madeye decode)
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Removed obsolete stuff from arch makefile.
mips had a special rule for generating asm-offsets.h so preserved it
using an architecture specific hook in top-level Kbuild file.
Renamed .h file to asm-offsets.h
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Self explanatory really. Some newer gcc's print a warning
if a function is used and we don't check its result.
We do this for a bunch of things in the kernel already,
this extends that to the PCI layer.
Based on a patch originally from Arjan van de Ven.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Building asm-offsets.h has been moved to a seperate Kbuild file
located in the top-level directory. This allow us to share the
functionality across the architectures.
The old rules in architecture specific Makefiles will die
in subsequent patches.
Furhtermore the usual kbuild dependency tracking is now used
when deciding to rebuild asm-offsets.s. So we no longer risk
to fail a rebuild caused by asm-offsets.c dependencies being touched.
With this common rule-set we now force the same name across
all architectures. Following patches will fix the rest.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn. The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices. It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove asm-ppc64/segment.h now that all users are gone.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix __power64__ typo that should be __powerpc64__ instead.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge a few asm-ppc and asm-ppc64 header files.
Note: the merge of setup.h intentionally does not carry
forward the m68k cruft. That means this patch continues
to break the already broken amiga on the ppc32.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make check_bugs() static inline and remove it from syscalls.c.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Standardize on _ASM_POWERPC_... prefix for all #include
exclusion symbols. Fixup all the non-compilers.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To start the timestamps with 0.0ms, easing the integer maths in the CCIDs, this
probably will be reworked to use the to be introduced struct timeval_offset
infrastructure out of skb_get_timestamp, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Include the ColdFire 523x register definitions when compiling
for that target processor.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support definitions for the integrated UARTs on the 523x ColdFire
processor family.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add processor level and clock support defines for the ColdFire 523x
processor.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.
I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets the isp116x to report overcurrent always per-port.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The isp116x chip will now always be in per-port power switching mode. Remove
conf options to set any other mode.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the power-on-to-power-good-time configuration option for
isp116x-hcd.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:
tree /sys/class/usb_device/
/sys/class/usb_device/
|-- usb1.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1
|-- usb2.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2
...
The presence of the "dev" file lets udev create real device nodes.
kay@pim:~/src/linux-2.6> tree /dev/bus/usb/
/dev/bus/usb/
|-- 1
| `-- 1
|-- 2
| `-- 1
...
udev rule:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c"
(echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/')
This makes libusb pick up the real nodes instead of the mounted usbfs:
export USB_DEVFS_PATH=/dev/bus/usb
Background:
All this makes it possible to manage usb devices with udev instead of
the devfs solution. We are currently working on a pam_console/resmgr
replacement driven by udev and a pam-helper. It applies ACL's to device
nodes, which is required for modern desktop functionalty like
"Fast User Switching" or multiple local login support.
New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.
This makes udev to provide symlinks for libusb to pick up:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"
/sbin/usbdevice:
#!/bin/sh
echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/'
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simple cleanup to eliminate X copies of the pci_enable_intx() function
in libata. Moved ahci.c's pci_intx() to pci.c and use it throughout
libata and msi.c.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- support PCI PM CAP version 3 (as defined in PCI PM Interface Spec v1.2)
- pci/probe.c sets the PM state initially to 4 which is D3cold. add a
PCI_UNKNOWN
- minor cleanups
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI error recovery infrastructure needs to be able to contact all
the drivers affected by a PCI error event, which may mean traversing
all the devices under a given PCI-PCI bridge. This patch adds a
function to the PCI core that traverses all the PCI devices on a PCI
bus and under any PCI-PCI bridges on that bus (and so on), calling a
given function for each device. This provides a way for the error
recovery code to iterate through all devices that are affected by an
error event.
This version is not implemented as a recursive function. Instead,
when we reach a PCI-PCI bridge, we set the pointers to start doing the
devices on the bus under the bridge, and when we reach the end of a
bus's devices, we use the bus->self pointer to go back up to the next
higher bus and continue doing its devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were three changes necessary in order to allow
sparc64 to use setup-res.c:
1) Sparc64 roots the PCI I/O and MEM address space using
parent resources contained in the PCI controller structure.
I'm actually surprised no other platforms do this, especially
ones like Alpha and PPC{,64}. These resources get linked into the
iomem/ioport tree when PCI controllers are probed.
So the hierarchy looks like this:
iomem --|
PCI controller 1 MEM space --|
device 1
device 2
etc.
PCI controller 2 MEM space --|
...
ioport --|
PCI controller 1 IO space --|
...
PCI controller 2 IO space --|
...
You get the idea. The drivers/pci/setup-res.c code allocates
using plain iomem_space and ioport_space as the root, so that
wouldn't work with the above setup.
So I added a pcibios_select_root() that is used to handle this.
It uses the PCI controller struct's io_space and mem_space on
sparc64, and io{port,mem}_resource on every other platform to
keep current behavior.
2) quirk_io_region() is buggy. It takes in raw BUS view addresses
and tries to use them as a PCI resource.
pci_claim_resource() expects the resource to be fully formed when
it gets called. The sparc64 implementation would do the translation
but that's absolutely wrong, because if the same resource gets
released then re-claimed we'll adjust things twice.
So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
conversion before passing it on to pci_claim_resource().
3) I was mistakedly __init'ing the function methods the PCI controller
drivers provide on sparc64 to implement some parts of these
routines. This was, of course, easy to fix.
So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register
info out to a separate file, where it belongs. Eventually we can stop including
this file from within pci.h, but lots of code needs to be audited first.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make PCI fixup data const, so it'll end up in a r/o section.
This also fixes the conversion into ECOFF which gets broken by too many
changes between r/w and r/o sections. Call it a hack but it's a change
that's correct by itself.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run PCI driver initialization on local node
Instead of adding messy kmalloc_node()s everywhere run the
PCI driver probe on the node local to the device.
This would not have helped for IDE, but should for
other more clean drivers that do more initialization in probe().
It won't help for drivers that do most of the work
on first open (like many network drivers)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow PXA platforms to pass an appropriate delay value to the
PXA MCI driver for delaying detection changes.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Proud member of Uglyhacks'R'US.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mmc_priv() has some nasty effects if the wrong pointer type is
passed to it. Introduce type checking, which also means we get
the right type. Also add an additional member to mmc_host which
is used to align host-private data appropriately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the crc16 routines, as used by w1 devices.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since GCC has to emit a call and a delay slot to the
out-of-line "membar" routines in arch/sparc64/lib/mb.S
it is much better to just do the necessary predicted
branch inline instead as:
ba,pt %xcc, 1f
membar #whatever
1:
instead of the current:
call membar_foo
dslot
because this way GCC is not required to allocate a stack
frame if the function can be a leaf function.
This also makes this bug fix easier to backport to 2.4.x
Signed-off-by: David S. Miller <davem@davemloft.net>
Asc2ax was still using a static buffer for all invocations which isn't
exactly SMP-safe. Change asc2ax to take an additional result buffer as
the argument. Change all callers to provide such a buffer.
This one only really is a fix for ROSE and as per recent discussions
there's still much more to fix in ROSE ...
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Else we get build failures like:
CC arch/sparc64/kernel/sparc64_ksyms.o
In file included from arch/sparc64/kernel/sparc64_ksyms.c:28:
include/net/compat.h:37: warning: "struct sock" declared inside parameter list
include/net/compat.h:37: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: David S. Miller <davem@davemloft.net>
Since packets almost never contain extra garbage at the end, it is
worthwhile to optimize for that case.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mmc_detect_change() to take a delay argument such that
the detection of card insertions and removals can be delayed
according to the requirements of the host driver or platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we copy 32bit ->msg_control contents to kernel, we walk the same
userland data twice without sanity checks on the second pass.
Second version of this patch: the original broke with 64-bit arches
running 32-bit-compat-mode executables doing sendmsg() syscalls with
unaligned CMSG data areas
Another thing is that we use kmalloc() to allocate and sock_kfree_s()
to free afterwards; less serious, but also needs fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the necessary changes to ensure that we flush the
caches correctly with aliasing VIPT caches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The problem is that klists claim to provide semantics for safe traversal of
lists which are being modified. The failure case is when traversal of a
list causes element removal (a fairly common case). The issue is that
although the list node is refcounted, if it is embedded in an object (which
is universally the case), then the object will be freed regardless of the
klist refcount leading to slab corruption because the klist iterator refers
to the prior element to get the next.
The solution is to make the klist take and release references to the
embedding object meaning that the embedding object won't be released until
the list relinquishes the reference to it.
(akpm: fast-track this because it's needed for the 2.6.13 scsi merge)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on patch from David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Support several new socket options / ancillary data:
IPV6_RECVPKTINFO, IPV6_PKTINFO,
IPV6_RECVHOPOPTS, IPV6_HOPOPTS,
IPV6_RECVDSTOPTS, IPV6_DSTOPTS, IPV6_RTHDRDSTOPTS,
IPV6_RECVRTHDR, IPV6_RTHDR,
IPV6_RECVHOPOPTS, IPV6_HOPOPTS
Old semantics are preserved as IPV6_2292xxxx so that
we can maintain backward compatibility.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ppc64 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are possible race conditions if probes are placed on routines within the
kprobes files and routines used by the kprobes. For example if you put probe
on get_kprobe() routines, the system can hang while inserting probes on any
routine such as do_fork(). Because while inserting probes on do_fork(),
register_kprobes() routine grabs the kprobes spin lock and executes
get_kprobe() routine and to handle probe of get_kprobe(), kprobes_handler()
gets executed and tries to grab kprobes spin lock, and spins forever. This
patch avoids such possible race conditions by preventing probes on routines
within the kprobes file and routines used by kprobes.
I have modified the patches as per Andi Kleen's suggestion to move kprobes
routines and other routines used by kprobes to a seperate section
.kprobes.text.
Also moved page fault and exception handlers, general protection fault to
.kprobes.text section.
These patches have been tested on i386, x86_64 and ppc64 architectures, also
compiled on ia64 and sparc64 architectures.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce new ll_rw_block() operation SWRITE meaning that block layer should
wait for the buffer lock and write-out afterwards. Hence data in buffers at
the time of call are guaranteed to be submitted to the disk.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The corgi keyboard has need of a switch event type with slightly type to the
input system as recommended by the input maintainer.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the platform specific Sharp SL-C7x0 LCD code from the
w100fb driver into a more appropriate place and updates the Corgi code to
match the new w100fb driver.
It also updates the corgi touchscreen code to match the new simplified
interface available from w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code w100fb was based on was horribly Sharp SL-C7x0 specific and there
was little else that could be done as I had no access to anything else with
a w100 in it. There is no real documentation about this chipset available.
Ian Molton has access to other platforms with the w100 (Toshiba e-series)
and so between us, we've improved w100fb and made it platform independent.
Ian Molton also added support for the very similar w3220 and w3200
chipsets.
There are a lot of changes here and it nearly amounts to a rewrite of the
driver but it has been extensively tested and is being used in preference
to the original driver in the Zaurus community. I'd therefore like to
update the mainline code to reflect this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a write protection switch handling code to the PXA MMC driver so
that platform specific code can provide it if available.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Infrastructure for 4-bit bus transfers with SD cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the SD specific SCR register from the card.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the read-only switch on SD cards which must be enforced by the
host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
