This MIPS driver does not support COMPILE_TEST yet and failed to build
under my radar.
Replace 'mtd' chich is not defined in the scope of xway_nand_remove()
by nand_to_mtd(chip). The mistake has been added in the long series
dropping nand_release().
Tested with a 7.3.0 MIPS GCC toolchain built with Buildroot.
Fixes: 9fdd78f7bc ("mtd: rawnand: xway: Stop using nand_release()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200626065511.16424-1-miquel.raynal@bootlin.com
Check and set master panic write flag so that low level drivers
can use it to take required action to ensure oops data gets written
to assigned mtdoops device partition.
Fixes: 9f897bfdd8 ("mtd: Add flag to indicate panic_write")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200615155134.32007-1-kdasu.kdev@gmail.com
* partition parser: Support MTD names containing one or more colons.
* mtdblock: clear cache_state to avoid writing to bad blocks repeatedly.
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
* Add, update support and fix few flashes.
* Prepare BFPT parsing for JESD216 rev D.
* Kernel doc fixes.
CFI changes:
* Support the absence of protection registers for Intel CFI flashes.
* Replace zero-length array with flexible-arrays.
-----BEGIN PGP SIGNATURE-----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=2M9Y
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- partition parser: Support MTD names containing one or more colons.
- mtdblock: clear cache_state to avoid writing to bad blocks
repeatedly.
Raw NAND core changes:
- Stop using nand_release(), patched all drivers.
- Give more information about the ECC weakness when not matching the
chip's requirement.
- MAINTAINERS updates.
- Support emulated SLC mode on MLC NANDs.
- Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
- Take check_only into account.
- Add an invalid ECC mode to discriminate with valid ones.
- Return an enum from of_get_nand_ecc_algo().
- Drop OOB_FIRST placement scheme.
- Introduce nand_extract_bits().
- Ensure a consistent bitflips numbering.
- BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
- Fix nand_gpio_waitrdy().
- Propage CS selection to sub operations.
- Add a NAND_NO_BBM_QUIRK flag.
- Give the possibility to verify a read operation is supported.
- Add a helper to check supported operations.
- Avoid indirect access to ->data_buf().
- Rename the use_bufpoi variables.
- Fix comments about the use of bufpoi.
- Rename a NAND chip option.
- Reorder the nand_chip->options flags.
- Translate obscure bitfields into readable macros.
- Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
- Fixed many error paths.
- Arasan
- New driver
- Au1550nd:
- Various cleanups
- Migration to ->exec_op()
- brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
- Cadence
- Make cadence_nand_attach_chip static.
- Cafe:
- Set the NAND_NO_BBM_QUIRK flag
- cmx270:
- Remove this controller driver.
- cs553x:
- Misc cleanup
- Migration to ->exec_op()
- Davinci:
- Misc cleanup.
- Migration to ->exec_op()
- Denali:
- Add more delays before latching incoming data
- Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
- Fsmc:
- Change to non-atomic bit operations.
- GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
- Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
- Marvell:
- Misc cleanup and small fixes
- Nandsim:
- Fix the error paths, driver wide.
- Omap_elm:
- Fix runtime PM imbalance.
- STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
- Add, update support and fix few flashes.
- Prepare BFPT parsing for JESD216 rev D.
- Kernel doc fixes.
CFI changes:
- Support the absence of protection registers for Intel CFI flashes.
- Replace zero-length array with flexible-arrays"
* tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (208 commits)
mtd: clear cache_state to avoid writing to bad blocks repeatedly
mtd: parser: cmdline: Support MTD names containing one or more colons
mtd: physmap_of_gemini: remove defined but not used symbol 'syscon_match'
mtd: rawnand: Add an invalid ECC mode to discriminate with valid ones
mtd: rawnand: Return an enum from of_get_nand_ecc_algo()
mtd: rawnand: Drop OOB_FIRST placement scheme
mtd: rawnand: Avoid a typedef
mtd: Fix typo in mtd_ooblayout_set_databytes() description
mtd: rawnand: Stop using nand_release()
mtd: rawnand: nandsim: Reorganize ns_cleanup_module()
mtd: rawnand: nandsim: Rename a label in ns_init_module()
mtd: rawnand: nandsim: Manage lists on error in ns_init_module()
mtd: rawnand: nandsim: Fix the label pointing on nand_cleanup()
mtd: rawnand: nandsim: Free erase_block_wear on error
mtd: rawnand: nandsim: Use an additional label when freeing the nandsim object
mtd: rawnand: nandsim: Stop using nand_release()
mtd: rawnand: nandsim: Free the partition names in ns_free()
mtd: rawnand: nandsim: Free the allocated device on error in ns_init()
mtd: rawnand: nandsim: Free partition names on error in ns_init()
mtd: rawnand: nandsim: Fix the two ns_alloc_device() error paths
...
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function call process is as follows:
mtd_blktrans_work()
while (1)
do_blktrans_request()
mtdblock_writesect()
do_cached_write()
write_cached_data() /*if cache_state is STATE_DIRTY*/
erase_write()
write_cached_data() returns failure without modifying cache_state
and cache_offset. So when do_cached_write() is called again,
write_cached_data() will be called again to perform erase_write()
on the same cache_offset.
But if this cache_offset points to a bad block, erase_write() will
always return -EIO. Writing to this mtdblk is equivalent to losing
the current data, and repeatedly writing to the bad block.
Repeatedly writing a bad block has no real benefits,
but brings some negative effects:
1 Lost subsequent data
2 Loss of flash device life
3 erase_write() bad blocks are very time-consuming. For example:
the function do_erase_oneblock() in chips/cfi_cmdset_0020.c or
chips/cfi_cmdset_0002.c may take more than 20 seconds to return
Therefore, when erase_write() returns -EIO in write_cached_data(),
clear cache_state to avoid writing to bad blocks repeatedly.
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Looks like some drivers define MTD names with a colon in it, thus
making mtdpart= parsing impossible. Let's fix the parser to gracefully
handle that case: the last ':' in a partition definition sequence is
considered instead of the first one.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ron Minnich <rminnich@google.com>
Tested-by: Ron Minnich <rminnich@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It's not used by anyone now, remove it. Fix the following gcc warning:
drivers/mtd/maps/physmap-gemini.c:49:34: warning: ‘syscon_match’ defined
but not used [-Wunused-const-variable=]
static const struct of_device_id syscon_match[] = {
^~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Support the absence of protection registers for Intel CFI flashes
* Replace zero-length array with flexible-arrays
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl7M2JMQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4wPtB/9yqMGejoFX8QLvtFLBCH9XZhuxRSXH3qCO
JXaqIrGSPBA3zb3po8z7dN5PoKUFQStXL8KrP1XcYKnZCE5l5p1qeSeYh3pBBmuN
eWuNCTwEco6h0SSjEw/AWjJ47MhV9Cp+vg7KmozLR1zrg+DJvdeURA0cj/DI5gNL
9DQDlxS7+WuejFAwYEKajDvrYZRqUF/XrfUtPxg9mrXsrwf0iPSra0zZ9ia+qZbE
sYw9EXngnf3NmSfrDQ0Y+g3ViqxTZBhrFN8MDnn/L3rCCv7llGxm0aC4mPWN5BRx
pinhIfFWZMgMSdvRG9sLN4qOT1SDRGG5HYpR67LGsObAFLnMGWS+
=jReG
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.8' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
CFI changes:
* Support the absence of protection registers for Intel CFI flashes
* Replace zero-length array with flexible-arrays
-----BEGIN PGP SIGNATURE-----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=HYf4
-----END PGP SIGNATURE-----
Merge tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Core block changes that have been queued up for this release:
- Remove dead blk-throttle and blk-wbt code (Guoqing)
- Include pid in blktrace note traces (Jan)
- Don't spew I/O errors on wouldblock termination (me)
- Zone append addition (Johannes, Keith, Damien)
- IO accounting improvements (Konstantin, Christoph)
- blk-mq hardware map update improvements (Ming)
- Scheduler dispatch improvement (Salman)
- Inline block encryption support (Satya)
- Request map fixes and improvements (Weiping)
- blk-iocost tweaks (Tejun)
- Fix for timeout failing with error injection (Keith)
- Queue re-run fixes (Douglas)
- CPU hotplug improvements (Christoph)
- Queue entry/exit improvements (Christoph)
- Move DMA drain handling to the few drivers that use it (Christoph)
- Partition handling cleanups (Christoph)"
* tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block: (127 commits)
block: mark bio_wouldblock_error() bio with BIO_QUIET
blk-wbt: rename __wbt_update_limits to wbt_update_limits
blk-wbt: remove wbt_update_limits
blk-throttle: remove tg_drain_bios
blk-throttle: remove blk_throtl_drain
null_blk: force complete for timeout request
blk-mq: drain I/O when all CPUs in a hctx are offline
blk-mq: add blk_mq_all_tag_iter
blk-mq: open code __blk_mq_alloc_request in blk_mq_alloc_request_hctx
blk-mq: use BLK_MQ_NO_TAG in more places
blk-mq: rename BLK_MQ_TAG_FAIL to BLK_MQ_NO_TAG
blk-mq: move more request initialization to blk_mq_rq_ctx_init
blk-mq: simplify the blk_mq_get_request calling convention
blk-mq: remove the bio argument to ->prepare_request
nvme: force complete cancelled requests
blk-mq: blk-mq: provide forced completion method
block: fix a warning when blkdev.h is included for !CONFIG_BLOCK builds
block: blk-crypto-fallback: remove redundant initialization of variable err
block: reduce part_stat_lock() scope
block: use __this_cpu_add() instead of access by smp_processor_id()
...
There is a risk that the fastmap anchor PEB is alternating between
just two PEBs, the current anchor and the previous anchor that was just
deleted. As the fastmap pools gets the first take on free PEBs, the
pools may leave no free PEBs to be selected as the new anchor,
resulting in the two PEBs alternating behaviour. If the anchor PEBs gets
a high erase count the PEBs will not be used by the pools but remain in
ubi->free, even more increasing the likelihood they will be used as
anchors.
Getting stuck using only a couple of PEBs continuously will result in an
uneven wear, eventually leading to failure.
To fix this:
- Choose the fastmap anchor when the most free PEBs are available. This is
during rebuilding of the fastmap pools, after the unused pool PEBs are
added to ubi->free but before the pools are populated again from the
free PEBs. Also reserve an additional second best PEB as a candidate
for the next time the fast map anchor is updated. If a better PEB is
found the next time the fast map anchor is updated, the candidate is
made available for building the pools.
- Enable anchor move within the anchor area again as it is useful for
distributing wear.
- The anchor candidate for the next fastmap update is the most suited free
PEB. Check this PEB's erase count during wear leveling. If the wear
leveling limit is exceeded, the PEB is considered unsuitable for now. As
all other non used anchor area PEBs should be even worse, free up the
used anchor area PEB with the lowest erase count.
Signed-off-by: Arne Edholm <arne.edholm@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage (WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAl7UbYYWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJpkgD/9/09OkJIWydwk2lr2T89HW5fSF
5uBT0a309/QDUpnV9yhcRsrESEicnvbtaGxD0kuYIInkiW/2cj1l689EkyRjUmy9
q3z4GzLqOlC7qvd7LUPFNGHmllBb09H/CxmXDxRP3aynB9oHzdpNQdPcpLBDA00r
0byp/AE48dFbKIhtT0QxpGUYZFOlyc7XVAaOkED4bmu148gx8q7MU1AxFgbx0Feb
9iPV0r6XYMgXJZ3sn/3PJsxF0V/giDSJ8ui2xsYRjCE408zVIYLdDs2e8dz+2yW6
+3Lyankgo+ofZc4XYExTYgn3WjhPFi+pjVRUaj+BcyTk9SLNIj2WmZdmcLMuzanh
BaUurmED7ffTtlsH4PhQgn8/OY4FX2PO2MwUHwlU+87Y8YDiW0lpzTq5H822OO8p
QQ8awql/6lLCJuyzuWIciVUsS65MCPxsZ4+LSiMZzyYpWu1sxrEY8ic3agzCgsA0
0i+4nZFlLG+Aap/oiKpegenkIyAunn2tDXAyFJFH6qLOiZJ78iRuws3XZqjCElhJ
XqvyDJIfjkJhWUb++ckeqX7ThOR4CPSnwba/7GHv7NrQWuk3Cn+GQ80oxydXUY6b
2/4eYjq0wtvf9NeuJ4/LYNXotLR/bq9zS0zqwTWG50v+RPmuC3bNJB+RmF7fCiCG
jo1Sd1LMeTQ7bnULpA==
=7s1u
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl7U4hUACgkQS1VPR6WN
FOkAjAf+Kxt87QGIOyQRybAhCJvHxRSiba+axmsM6dSn6+GoAPLRcxeW3fXOark6
gPlmY31+yFyGAGcUO/w51woc/NS4vicRhW+bxzcf/DSl88UJCZyr+G7QP14dcjQY
Zts2+sa44tdmo+DdxKUxfs4t9xQFNXIvM2Y1Rlb8KsJGKP4xLyXs0R6a4Xgo5qEX
wtMe2D+DoQ5rlnv98bDoaeRGkhq+n1aqt0zPLKHit1wcOEH7PseiwaKDIPhbTW0K
sIdSrzEb8aEzVt9pLuRig9NLFlwYK7mpfjdnOoR5oKTl1nQI44hBjAU/dnTL67YP
Bt/WNTaSwj/6XGhYA55+zxn5rJ3pQQ==
=w6a9
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl7TdZMACgkQJWrqGEe9
VoRthQgAttWsImXpEUa8C8CXvPhjpb6uZ7QYM4PSE0bheuVi7ivoDPyYWopno30h
R6UntGbsBqPyvDFDUxUEvyvn5F0JQK1dLif+7X0Ki5on6LkYdEuanHaSMZmSIXD8
atNhLVO1FeD3EulN8Dw9hGy6OrNT8O2bESbiJrCpOk9s6yAPINhKqZVJsyShcTs5
tc94/J0DIF7og8cdH4wYoz+AWw0WaHvPsn5VWnTy08gk7dB7hsq/DeftZmrJLL0g
B7Et1pvcLBSNBGBpzS6rEjXb/e3+wdKnNy0AQvrMdEZUzN3h9aY5sCLSFOsFfKQ+
xjxJgmyoKk0C9uCeNaPt8c7gTgAZAA==
=Gz6y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
This introduces mtdpstore, which is similar to mtdoops but more
powerful. It uses pstore/blk, and aims to store panic and oops logs to
a flash partition, where pstore can later read back and present as files
in the mounted pstore filesystem.
To make mtdpstore work, the "blkdev" of pstore/blk should be set
as MTD device name or MTD device number. For more details, see
Documentation/admin-guide/pstore-blk.rst
This solves a number of issues:
- Work duplication: both of pstore and mtdoops do the same job storing
panic/oops log. They have very similar logic, registering to kmsg
dumper and storing logs to several chunks one by one.
- Layer violations: drivers should provides methods instead of polices.
MTD should provide read/write/erase operations, and allow a higher
level drivers to provide the chunk management, kmsg dump
configuration, etc.
- Missing features: pstore provides many additional features, including
presenting the logs as files, logging dump time and count, and
supporting other frontends like pmsg, console, etc.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-11-keescook@chromium.org/
Link: https://lore.kernel.org/r/1589266715-4168-1-git-send-email-liaoweixiong@allwinnertech.com
Signed-off-by: Kees Cook <keescook@chromium.org>
NAND ECC modes (or providers) have their own enumeration but, unlike
their algorithms counterpart, there is no invalid or uninitialized
value to discriminate between an error and having chosen a no-ECC
situation. Add an "invalid" entry for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-7-miquel.raynal@bootlin.com
This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().
Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Now that all drivers have been converted to do not use nand_release()
anymore, let's remove this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-63-miquel.raynal@bootlin.com
nand_release() basically calls mtd_device_unregister() and
nand_cleanup(). Both helpers should be called after MTD device
registration and NAND scan, respectively. Drop nand_release() and use
the two helpers directly so that they fit the error path and the
labels there.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-12-miquel.raynal@bootlin.com
ns_free() is the helper that is called symmetrically to ns_init() and
so should free the same objects, including the partition names.
Now, callers of ns_free() do not need to free this partition names
themselves.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-11-miquel.raynal@bootlin.com
Many function calls are done this way:
if ((retval = func()) != 0)
return retval;
while we expect in the kernel function calls like:
retval = func();
if (retval)
return retval;
Apply this change where possible and also use "ret" instead of
"retval" in ns_init_module for consistency, as it is only used in this
function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-5-miquel.raynal@bootlin.com
Some functions are prefixed "nandsim_", others "ns_" and many are
simply not prefixed at all. Make this file consistent by prefixing all
functions by "ns_".
This is a mechanical change. Sometimes the line is a bit reworked as
well to fit the kernel coding style. For instance, there are several
places where displayed strings are cut. When one of this line is
changed because of the naming update, the two parts of the strings
gets concatenated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-4-miquel.raynal@bootlin.com
Only v3.3-v5.0 have a different CS0 layout.
Controllers before v3.3 use the same layout for every CS.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522104008.28340-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
Let's convert the driver to exec_op() to have one less driver relying
on the legacy interface.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-4-boris.brezillon@collabora.com
The rb-gpios semantics was undocumented and qi,lb60 (along with the
ingenic driver) got it wrong. The active state encodes the NAND ready
state, which is high level. Since there's no signal inverter on this
board, it should be active-high. Let's fix that here for older DTs so
we can re-use the generic nand_gpio_waitrdy() helper, and be consistent
with what other drivers do.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-3-boris.brezillon@collabora.com
