For coldfire with MMU enabled, data cache did not follow the configuration but
was configured in writethrough mode.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add support for the Coldfire 5441x (54410/54415/54416/54417/54418). Currently
we only support noMMU mode. It requires the PIT patch posted previously as it
uses the PIT instead of the dma timer as a clock source so we can get all that
GENERIC_CLOCKEVENTS goodness. It also adds some simple clk definitions and
very simple minded power management. The gpio code is tweeked and some
additional devices are added to devices.c. The Makefile uses -mv4e as
apparently, the only difference a v4m (m5441x) and a v4e is the later has a
FPU, which I don't think should matter to us in the kernel.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Modify the cache setup for the ColdFire 54xx parts when running with
the MMU enabled.
We want to map the peripheral register space (MBAR region) as non
cacheable. And create an identity mapping for all of RAM for the
kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Create separate functions to deal with instruction and data cache flushing.
This way we can optimize them for the vairous cache types and arrangements
used across the ColdFire family.
For example the unified caches in the version 3 cores means we don't
need to flush the instruction cache. For the version 2 cores that do
not do data cacheing (or where we choose instruction cache only) we
don't need to do any data flushing.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The version 3 and version 4 ColdFire cache controllers support both
write-through and copy-back modes on the data cache. Allow for Kconfig
time configuration of this, and set the cache mode appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the code to push cache lines is only available to version 4
cores. Version 3 cores may also need to use this if we support copy-
back caches on them. Move this code to make it more generic, and
useful for all version ColdFire cores.
With this in place we can now have a single cache_flush_all() code
path that does all the right things on all version cores.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cache control code for the ColdFire CPU's is a big ugly mess
of "#ifdef"ery liberally coated with bit constants. Clean it up.
The cache controllers in the various ColdFire parts are actually quite
similar. Just differing in some bit flags and options supported. Using
the header defines now in place it is pretty easy to factor out the
small differences and use common setup and flush/invalidate code.
I have preserved the cache setups as they where in the old code
(except where obviously wrong - like in the case of the 5249). Following
from this it should be easy now to extend the possible setups used on
the CACHE controllers that support split cacheing or copy-back or
write through options.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The more modern ColdFire parts (even if based on older version cores)
have separate user and supervisor stack pointers (a7 register).
Modify the ColdFire CPU setup and exception code to enable and use
this on parts that have it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 547x family of processors is very similar to the ColdFire
548x series. Almost all of the support for them is the same. Make the
code supporting the 548x more gneric, so it will be capable of
supporting both families.
For the most part this is a renaming excerise to make the support
code more obviously apply to both families.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Now that we have meaningfull symbolic constants for bit definitions
of the cache registers of m5407 and m548x chips, use them to
improve readability, portability and efficiency of the cache operations.
This also fixes __flush_cache_all for m548x chips : implicit
DCACHE_SIZE was exact for m5407, but wrong for m548x.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
__flush_cache_all for m54xx is intrinsically related to the bit
definitions in m54xxacr.h. Move it there from cacheflush_no.h,
for easier maintenance.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MCF548x have the same cache control registers as the MCF5407.
Extract the bit definitions for the ACR and CACR registers from m5407sim.h
and move them to a new file m54xxacr.h. Those definitions are not used
anywhere yet, so no other file is involved. This is a preparation for
m54xx cache support cleanup.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
