qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.
Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call chain is this:
qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again
It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.
When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.
While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices. As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.
The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered. The notifier
registration and unregistration calls are no longer conditionally
compiled. And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>
Commit a0d4922da2
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual devs entry for 2116:0320
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
http://www.fastraxgps.com/products/evaluationtools/evaluationkit/
to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.
The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: Wolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carry out the PM-routine interface change in the USB OTG pathway. This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4a90f09b20 added kref stuff to
ftdi_sio, but missed tty_kref_put at one exit point in
ftdi_process_read.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the Multi-Tech cellular modem firmware to the TI USB serial driver.
This firmware was extracted from:
ftp://ftp.multitech.com/wireless/wireless_linux.zip
Firmware licence: "all firmware components are redistributable in binary
form" per support@multitech.com
Copyright (C) 2005 Multi-Tech Systems, Inc.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Multi-Tech cellular modem support to the ti_usb_3410_5052 driver.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TI USB serial driver supports specifying alternate vendor and
product IDs (since the chips can and are used in devices under other
vendor/product IDs). However, the alternate IDs were not loaded in the
combined product table. This patch also adds support for loading
alternate firmware for alternate vendor/product IDs.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawell found a case where a NULL check was misplaced in the
usb-serial code. However as the object in question cannot be NULL the
check can simply be removed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
