[ Upstream commit d789a490d32fdf0465275e3607f8a3bc87d3f3ba ]
Fix to return -ENOTSUPP instead of 0 when PCS_HAS_PINCONF is true, which
is the same as that returned in pcs_parse_pinconf().
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210722033930.4034-2-thunder.leizhen@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70115558ab02fe8d28a6634350b3491a542aaa02 ]
Commit 1abd18d1a5 ("pinctrl: samsung: Register pinctrl before GPIO")
changes the order of GPIO and pinctrl registration: now pinctrl is
registered before GPIO. That means gpio_chip->ngpio is not set when
samsung_pinctrl_register() called, and one cannot rely on that value
anymore. Use `pin_bank->nr_pins' instead of `pin_bank->gpio_chip.ngpio'
to fix mentioned inconsistency.
Fixes: 1abd18d1a5 ("pinctrl: samsung: Register pinctrl before GPIO")
Signed-off-by: Jaehyoung Choi <jkkkkk.choi@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210730192905.7173-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf8d6899b1e8906dc076ef26cc633e96a8bb0c3 ]
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d69530 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43878eb7c83d3335af7737dcce1fa79071065dfe ]
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5e931403942b3af39212960c2592b5ba741b2bf upstream.
Fix the pull up/down info for both the JZ4760 and JZ4770 SoCs, as the
previous values sometimes contradicted what's written in the programming
manual.
Fixes: b5c23aa465 ("pinctrl: add a pinctrl driver for the Ingenic jz47xx SoCs")
Cc: <stable@vger.kernel.org> # v4.12
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20210717174836.14776-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b73e588f47397dee6e4bdfd953e0306c60b5fe5 upstream.
Casting a small array of u8 to an unsigned long is *never* OK:
- it does funny thing when the array size is less than that of a long,
as it accesses random places in the stack
- it makes everything even more fun with a BE kernel
Fix this by building the unsigned long used as a bitmap byte by byte,
in a way that works across endianess and has no undefined behaviours.
An extra BUILD_BUG_ON() catches the unlikely case where the array
would be larger than a single unsigned long.
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Cc: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/r/20210725180830.250218-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f658f7a3953f6d70bab90e117aff8d0ad44e200 ]
The software mapping for GPIO, which initially comes from Microsoft,
is subject to change by respective Windows and firmware developers.
Due to the above the driver had been written and published way ahead
of the schedule, and thus the numbering schema used in it is outdated.
Fix the numbering schema in accordance with the real products on market.
Fixes: 653d96455e ("pinctrl: tigerlake: Add support for Tiger Lake-H")
Reported-and-tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Riccardo Mori <patacca@autistici.org>
Reported-and-tested-by: Lovesh <lovesh.bond@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213463
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213579
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213857
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798a315fc359aa6dbe48e09d802aa59b7e158ffc ]
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
Fixes: 81bd1579b43e ("pinctrl: mediatek: Fix fallback call path")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20210701080955.2660294-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 884af72c90016cfccd5717439c86b48702cbf184 upstream.
Add the missing unlock before return from function mcp23s08_irq()
in the error handling case.
v1-->v2:
remove the "return IRQ_HANDLED" line
Fixes: 897120d41e7a ("pinctrl: mcp23s08: fix race condition in irq handler")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1623134048-56051-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ca46d3e43569186bd1decfb02a6b4c4ddb4304b upstream.
Add device HID AMDI0031 to the AMD GPIO controller driver match table.
This controller can be found on Microsoft Surface Laptop 4 devices and
seems similar enough that we can just copy the existing AMDI0030 entry.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210316.1982416-1-luzmaximilian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 897120d41e7afd9da435cb00041a142aeeb53c07 ]
Checking value of MCP_INTF in mcp23s08_irq suggests that the handler may be
called even when there is no interrupt pending.
But the actual interrupt could happened between reading MCP_INTF and MCP_GPIO.
In this situation we got nothing from MCP_INTF, but the event gets acknowledged
on the expander by reading MCP_GPIO. This leads to losing events.
Fix the problem by not reading any register until we see something in MCP_INTF.
The error was reproduced and fix tested on MCP23017.
Signed-off-by: Radim Pavlik <radim.pavlik@tbs-biometrics.com>
Link: https://lore.kernel.org/r/AM7PR06MB6769E1183F68DEBB252F665ABA3E9@AM7PR06MB6769.eurprd06.prod.outlook.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7f444499d6faf9a6ae3b27ec094109528d2b9a7 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210508031502.53637-1-cuibixuan@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cee31cd49733e89dfedf4f68a56839fc2e42040 ]
R-Car Gen3 Hardware Manual Errata for Rev. 0.52 of Nov 30, 2016, added
the configuration bit for bias pull-down control for the PRESET# pin on
R-Car M3-W. Add driver support for controlling pull-down on this pin.
Fixes: 2d40bd2427 ("pinctrl: sh-pfc: r8a7796: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/c479de5b3f235c2f7d5faea9e7e08e6fccb135df.1619785375.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67e2996f72c71ebe4ac2fcbcf77e54479bb7aa11 ]
Each GPIO bank supports a variable number of lines which is usually 16, but
is less in some cases : this is specified by the last argument of the
"gpio-ranges" bank node property.
Report to the framework, the actual number of lines, so the libgpiod
gpioinfo command lists the actually existing GPIO lines.
Fixes: 1dc9d28915 ("pinctrl: stm32: add possibility to use gpio-ranges to declare bank range")
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20210617144629.2557693-1-fabien.dessenne@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0c10a5f3a49130dd11281aa27e7e1c8654abc7 ]
The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel(). On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
64-bit.
Addresses-Coverity: Unintentional integer overflow
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20210408195029.69974-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd85125ea88513f637a62a72e8949c579c5c0a87 ]
A System Error (SError, followed by kernel panic) was detected when
trying to print the supported pins in a pinctrl device which supports
multiple pins per register. This change fixes the pcs_pin_dbg_show() in
pinctrl-single driver when bits_per_mux is not zero. In addition move
offset calculation and pin offset in register to common function.
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20210319152133.28705-4-hhhawa@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 482715ff0601c836152b792f06c353464d826b9b ]
The commit f1b206cf7c ("pinctrl: core: print gpio in pins debugfs file")
enabled GPIO pin number and label in debugfs for pin controller. However,
it limited that feature to the chips where base is positive number. This,
in particular, excluded chips where base is 0 for the historical or backward
compatibility reasons. Refactor the code to include the latter as well.
Fixes: f1b206cf7c ("pinctrl: core: print gpio in pins debugfs file")
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Drew Fustini <drew@beagleboard.org>
Reviewed-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20210415130356.15885-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196d941753297d0ca73c563ccd7d00be049ec226 ]
When updating pin names for Intel Lewisburg, the numbers of pins were
left behind. Update them accordingly.
Fixes: e66ff71fd0 ("pinctrl: lewisburg: Update pin list according to v1.1v6")
Signed-off-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c971af25cda94afe71617790826a86253e88eab0 upstream.
The restore in resume should match to suspend which only set for RK3288
SoCs pinctrl.
Fixes: 8dca933127 ("pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume")
Reviewed-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wang Panzhenzhuan <randy.wang@rock-chips.com>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210223100725.269240-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf9d052aa6005f1e8dfaf491d83bf37f368af69e upstream.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a95881d6aa2c000e3649f27a1a7329cf356e6bb3 upstream.
In commit 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4079d35fa4fca4ee0ffd66968312fc86a5e8c290 upstream.
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82e537807d5c85706cd4c16fd2de77a8495dc8d upstream.
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81bd1579b43e0e285cba667399f1b063f1ce7672 ]
Some SoCs, eg. mt8183, are using a pinconfig operation bias_set_combo.
The fallback path in mtk_pinconf_adv_pull_set() should also try this
operation.
Fixes: cafe19db77 ("pinctrl: mediatek: Backward compatible to previous Mediatek's bias-pull usage")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20201228090425.2130569-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92ff62a7bcc17d47c0ce8dddfb7a6e1a2e55ebf4 ]
The SCU offset for signal PWM8 in group PWM8G0 is wrong, fix it from
SCU414 to SCU4B4.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Fixes: 2eda1cdec4 ("pinctrl: aspeed: Add AST2600 pinmux support")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201217024912.3198-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9a85c09a3f507b925d75cb0c7c8f364467038052 upstream.
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5c ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1158e36f876f6269978a4176e3a1d48d27fe7a1 upstream.
It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.
So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/85263ce8b058e80cea25c6ad6383eb256ce96cc8.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6de7ed693c631d4689acfe90c434147598d75543 ]
A100's pin starts with PB, so it should start with 1.
Fixes: 473436e764 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/9db51667bf9065be55beafd56e5c319e3bbe8310.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mistakenly the buffers (input and output) become enabled together for a short
period of time during GPIO request. This is problematic, because instead of
initial motive to disable them in the commit af7e3eeb84
("pinctrl: intel: Disable input and output buffer when switching to GPIO"),
the driven value on the pin, which might be used as an IRQ line, brings
firmwares of some touch pads to an awkward state that needs a full power off
to recover. Fix this, as stated in the culprit commit, by disabling the buffers.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210497
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201208182403.40435-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 6726fbff19bf ("pinctrl: aspeed: Fix GPI only function problem.")
fixes access to GPIO banks T and U on the AST2600. Both banks contain
input-only pins and the GPIO pin function is named GPITx and GPIUx
respectively. Unfortunately the fix had a negative impact on GPIO banks
D and E for the AST2400 and AST2500 where the GPIO pass-through
functions take similar "GPI"-style names. The net effect on the older
SoCs was that when the GPIO subsystem requested a pin in banks D or E be
muxed for GPIO, they were instead muxed for pass-through mode.
Mistakenly muxing pass-through mode e.g. breaks booting the host on
IBM's Witherspoon (AC922) platform where GPIOE0 is used for FSI.
Further exploit the names in the provided expression structure to
differentiate pass-through from pin-specific GPIO modes.
This follow-up fix gives the expected behaviour for the following tests:
Witherspoon BMC (AST2500):
1. Power-on the Witherspoon host
2. Request GPIOD1 be muxed via /sys/class/gpio/export
3. Request GPIOE1 be muxed via /sys/class/gpio/export
4. Request the balls for GPIOs E2 and E3 be muxed as GPIO pass-through
("GPIE2" mode) via a pinctrl hog in the devicetree
Rainier BMC (AST2600):
5. Request GPIT0 be muxed via /sys/class/gpio/export
6. Request GPIU0 be muxed via /sys/class/gpio/export
Together the tests demonstrate that all three pieces of functionality
(general GPIOs via 1, 2 and 3, input-only GPIOs via 5 and 6, pass-through
mode via 4) operate as desired across old and new SoCs.
Fixes: 9b92f5c51e ("pinctrl: aspeed: Fix GPI only function problem.")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Billy Tsai <billy_tsai@aspeedtech.com>
Cc: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201126063337.489927-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
-----BEGIN PGP SIGNATURE-----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=xymw
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-3' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-3
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GPIOs that attempt to use interrupts get thwarted with a message like:
"pin 161 cannot be used as IRQ" (for instance with SD_CD). This is because
the HOSTSW_OWN offset is incorrect, so every GPIO looks like it's
owned by ACPI.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the group of pins is hidden in the pin list it affects
the register offset calculation despite fixed GPIO base.
Hence, the offsets of all pins after the hidden group
are broken. Instead we have to unhide the group and use a flag
to exclude it from GPIO number space.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Reported-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAl+lkxIACgkQb7wzTHR8
rChnvA//WtUChge5HzlJu/6/Eim32S1N8HPaEsxEpNT3B/D8T3KFhpcbzTM+7tDC
3HLgqTa/r/VmCbJH1Su//VFLBRIndYjSZKgLl2c++YQe5bTxWR0HY+su2U5Fzf24
TwpeuhM8+7mWCvI4VeEOULZaZ+3OSfTbg9ccGZB7pD6GLonVSogs6eg4tdNeMDDs
Lv5GQLc8NrPJZyKqnc5S3GScyY9bemQG8gGjtDSOo8YPMGxPQl2Mcz5iEOlw6lzT
dGvB184X4XTD4L9RgYtEJmP9peEEG2xJuWOzxUI1EkitA7j9MwyNPjeQITv1UV5i
HWIN91cqBGPv/ic286mVAdP0lnAcYiOF/yVHDkW4zKDj1QC35wj26eRQcuqTfEZS
owqb0hEP2NlCqBGWHHOIsxCaTaPokO4pG0zsLjXNmw1z1wGfIJncRwNha0cfcQEE
UDUXNcBiDceh5xYz/0unj4TxMTFOfmIwTtn3CkOVJMiNMsKCJfXl0+KKLN0D/ebg
FtrXYfwK6f4clFBxD9wqLT7UwzYX6Bnn4fLA3Z+LPRKenpXDZ8guld//rn98mcAp
0hAEER1YceUnADEPwKftBxH3iO4SLQQQdoLFWYu4MGybbzSLi65EkwI16GWy5y94
EcQRFlGsdIMH7rSVV6934qI3CYq53intnjFNQh+Bk8omiteV9Us=
=Voi9
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-2
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
Specify the PDC mapping for SM8250, so that gpio interrupts are
propertly mapped to the wakeup IRQs of the PDC.
Fixes: 4e3ec9e407 ("pinctrl: qcom: Add sm8250 pinctrl driver.")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201028043642.1141723-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1604561884-10166-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RTC is 32.768kHz thus 512 RtcClk equals 15625 usec. The documentation
likely has dropped precision and that's why the driver mistakenly took
the slightly deviated value.
Cc: stable@vger.kernel.org
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/linux-gpio/2f4706a1-502f-75f0-9596-cc25b4933b6c@redhat.com/
Link: https://lore.kernel.org/r/20201105231912.69527-3-coiby.xu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some gpio pin at aspeed soc is input only and the prefix name of these
pin is "GPI" only.
This patch fine-tune the condition of GPIO check from "GPIO" to "GPI"
and it will fix the usage error of banks D and E in the AST2400/AST2500
and banks T and U in the AST2600.
Fixes: 4d3d0e4272 ("pinctrl: Add core support for Aspeed SoCs")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201030055450.29613-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is useful for debugging to have the error message printed
when regmap initialisation fails. Add it to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-2-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that simplification of mcp23s08_spi_regmap_init() made
a regression due to wrong size calculation for dev_kmemdup() call.
It misses the fact that config variable is already a pointer, thus
the sizeof() calculation is wrong and only 4 or 8 bytes were copied.
Fix the parameters to devm_kmemdup() to copy a full chunk of memory.
Fixes: 0874758ecb ("pinctrl: mcp23s08: Refactor mcp23s08_spi_regmap_init()")
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-1-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove totally irq mappings create in probe, the gpio irq mapping will
be created when do
gpio_to_irq ->
rockchip_gpio_to_irq ->
irq_create_mapping
This patch can speed up system boot on, also abandon many unused irq
mappings' create.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-4-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There need to enable pclk_gpio when do irq_create_mapping, since it will
do access to gpio controller.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>