The managed interface PS was not disabled when a GO interface
was added. As a consequence, when the station VMAC was in PS,
the GO also was not on the medium. Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to clean all kinds of bad state it might be in.
This solves situation where HW RFkill was switched while
the NIC was offline.
Until now, we relied on the firmware to do clean the
interrupt, but new firmwares don't do that any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IRQ handler nuc900fb_irqhandler() use dev_id as a type of
struct nuc900fb_info *, so we should pass fbi as the device
identity to request_irq().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regs_phys is phys_addr_t (u32 or u64).
Lets use %pa printk format specifier.
Fixes compilation warning introduced by:
video: xilinxfb: Use drvdata->regs_phys instead of physaddr
(sha1: c88fafef01)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.
I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.
This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]
Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Need to use the driver state rather than the register
state since the displays may not be enabled when the
power state is programmed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Convert CONFIG_HOTPLUG_PCI from tristate to bool. This only affects
the hotplug core; several of the hotplug drivers can still be modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Hot-removing a device with SR-IOV enabled causes a null pointer dereference
in v3.9 and v3.10.
This is a regression caused by ba518e3c17 ("PCI: pciehp: Iterate over all
devices in slot, not functions 0-7"). When we iterate over the
bus->devices list, we first remove the PF, which also removes all the VFs
from the list. Then the list iterator blows up because more than just the
current entry was removed from the list.
ac205b7bb7 ("PCI: make sriov work with hotplug remove") works around a
similar problem in pci_stop_bus_devices() by iterating over the list in
reverse, so the VFs are stopped and removed from the list first, before the
PF.
This patch changes pciehp_unconfigure_device() to iterate over the list in
reverse, too.
[bhelgaas: bugzilla, changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60604
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yijing Wang <wangyijing@huawei.com>
CC: stable@vger.kernel.org # v3.9+
If hci_dev_open() is called after hci_register_dev() added the device to
the hci_dev_list but before the workqueue are created we could run into a
NULL pointer dereference (see below).
This bug is very unlikely to happen, systems using bluetoothd to
manage their bluetooth devices will never see this happen.
BUG: unable to handle kernel NULL pointer dereference
0100
IP: [<ffffffff81077502>] __queue_work+0x32/0x3d0
(...)
Call Trace:
[<ffffffff81077be5>] queue_work_on+0x45/0x50
[<ffffffffa016e8ff>] hci_req_run+0xbf/0xf0 [bluetooth]
[<ffffffffa01709b0>] ? hci_init2_req+0x720/0x720 [bluetooth]
[<ffffffffa016ea06>] __hci_req_sync+0xd6/0x1c0 [bluetooth]
[<ffffffff8108ee10>] ? try_to_wake_up+0x2b0/0x2b0
[<ffffffff8150e3f0>] ? usb_autopm_put_interface+0x30/0x40
[<ffffffffa016fad5>] hci_dev_open+0x275/0x2e0 [bluetooth]
[<ffffffffa0182752>] hci_sock_ioctl+0x1f2/0x3f0 [bluetooth]
[<ffffffff815c6050>] sock_do_ioctl+0x30/0x70
[<ffffffff815c75f9>] sock_ioctl+0x79/0x2f0
[<ffffffff811a8046>] do_vfs_ioctl+0x96/0x560
[<ffffffff811a85a1>] SyS_ioctl+0x91/0xb0
[<ffffffff816d989d>] system_call_fastpath+0x1a/0x1f
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Memory allocated by vmalloc (including stack) can not be used for DMA,
i.e. data pointer on usb_control_msg() should not point to stack memory.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=977558
Reported-and-tested-by: Andy Lawrence <dr.diesel@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The length check is invalid since the length varies with type of
info response.
This was introduced by the commit cb3b3152b2
Because of this, l2cap info rsp is not handled and command reject is sent.
> ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Info rsp: type 2 result 0
Extended feature mask 0x00b8
Enhanced Retransmission mode
Streaming mode
FCS Option
Fixed Channels
< ACL data: handle 11 flags 0x00 dlen 10
L2CAP(s): Command rej: reason 0
Command not understood
Cc: stable@vger.kernel.org
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Chan-Yeol Park <chanyeol.park@samsung.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leaks introduced in commits:
40d133d7f5
usb: gadget: f_ncm: convert to new function interface with backward compatibility
fee562a645
usb: gadget: f_ecm: convert to new function interface with backward compatibility
fcbdf12ebe
usb: gadget: f_phonet: convert to new function interface with backward compatibility
b29002a157
usb: gadget: f_eem: convert to new function interface with backward compatibility
8cedba7c73
usb: gadget: f_subset: convert to new function interface with backward compatibility
f466c63538
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocated urbs and buffers were never freed on errors in open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leaks introduced in commits:
40d133d7f5
usb: gadget: f_ncm: convert to new function interface with backward compatibility
fee562a645
usb: gadget: f_ecm: convert to new function interface with backward compatibility
fcbdf12ebe
usb: gadget: f_phonet: convert to new function interface with backward compatibility
b29002a157
usb: gadget: f_eem: convert to new function interface with backward compatibility
8cedba7c73
usb: gadget: f_subset: convert to new function interface with backward compatibility
f466c63538
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix bugs introduced in
9c62ce83e4
usb: gadget: ether: convert to new interface of f_ecm
94b5573e97
usb: gadget: ether: convert to new interface of f_eem
8af5232d6f
usb: gadget: ether: convert to new interface of f_subset
9bd4a10e1b
usb: gadget: ether: convert to new interface of f_rndis
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hi Greg,
Here's five bug fixes for 3.12.
The three patches are marked for stable. Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.
The other two patches fix build warnings.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BrdB
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes, now with more tags!
Hi Greg,
Here's five bug fixes for 3.12.
The three patches are marked for stable. Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.
The other two patches fix build warnings.
Sarah Sharp
When we made all inode updates transactional, we no longer needed
the log recovery detection for inodes being newer on disk than the
transaction being replayed - it was redundant as replay of the log
would always result in the latest version of the inode would be on
disk. It was redundant, but left in place because it wasn't
considered to be a problem.
However, with the new "don't read inodes on create" optimisation,
flushiter has come back to bite us. Essentially, the optimisation
made always initialises flushiter to zero in the create transaction,
and so if we then crash and run recovery and the inode already on
disk has a non-zero flushiter it will skip recovery of that inode.
As a result, log recovery does the wrong thing and we end up with a
corrupt filesystem.
Because we have to support old kernel to new kernel upgrades, we
can't just get rid of the flushiter support in log recovery as we
might be upgrading from a kernel that doesn't have fully transactional
inode updates. Unfortunately, for v4 superblocks there is no way to
guarantee that log recovery knows about this fact.
We cannot add a new inode format flag to say it's a "special inode
create" because it won't be understood by older kernels and so
recovery could do the wrong thing on downgrade. We cannot specially
detect the combination of zero mode/non-zero flushiter on disk to
non-zero mode, zero flushiter in the log item during recovery
because wrapping of the flushiter can result in false detection.
Hence that makes this "don't use flushiter" optimisation limited to
a disk format that guarantees that we don't need it. And that means
the only fix here is to limit the "no read IO on create"
optimisation to version 5 superblocks....
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit e60896d8f2)
We forgot to free the node itself when free:ing a map.
Reported-by: xulinuxkernel <xulinuxkernel@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.
This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb14 "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Fix warning when CONFIG_PCI is not enabled
(from commit 2963657819).
drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]
These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.
Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().
The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL. The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.
However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory. xhci_free_dev checks the return value from the generic
xhci_check_args function. If the return value is -ENODEV, it carries on
trying to free the virtual device.
The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer. It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.
The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.
See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details. This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.
This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b4017 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org
commit 181d1b9e31
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 13:16:24 2013 +0200
drm/i915: fix up gt init sequence fallout
moved dev_priv->gt_lock initialization after use. Do the initialization
much earlier with other spin lock initializations.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: stable@vger.kernel.org (since the regressing patch is also cc: stable)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current regdomain was not always set by the core. This causes
cards with a custom regulatory domain to ignore user initiated changes
if done before the card was registered.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
This is another batch of fixes intended for the 3.11 stream. FWIW,
this is the first request with fixes from the mac80211 and iwlwifi
trees as well.
Regarding the mac80211 bits, Johannes says:
"Here I have a fix for RSSI thresholds in mesh, two minstrel fixes from
Felix, an nl80211 fix from Michal and four various fixes I did myself."
As for the iwlwifi bits, Johannes says:
"Here I have a fix for debugfs directory creation (causing a spurious
error message), two scanning fixes from David Spinadel, an LED fix and
two patches related to a BA session problem that eventually caused
firmware crashes from Emmanuel and a small BT fix for older devices as
well as a workaround for a firmware problem with APs with very small
beacon intervals from myself."
Along with those:
Arend van Spriel addresses a lock-up and a NULL pointer dereference
in brcmfmac.
Daniel Drake fixes an unhandled interrupt during device tear down
in mwifiex.
Larry Finger corrects a wil6210 build error.
Oleksij Rempel fixes two ath9k_htc problems related to keeping the
driver and firmware in sync.
Solomon Peachy gives us a cw1200 fix to avoid an oops in monitor mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.
This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).
So schedule those writes when s.replacing is set as well.
In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete. So introduce STRIPE_REPLACED to
record if the replacement has happened.
For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test. The latter
ensure that now IO has been flagged but not started. The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.
Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.
Finally if a NeedReplace device is not UPTODATE then that is an
error. We really must trigger a warning.
This bug was introduced in commit 9a3e1101b8
(md/raid5: detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.
Cc: stable@vger.kernel.org (3.3+)
Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua <qindehua@163.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We always need to be careful when calling generic_make_request, as it
can start a chain of events which might free something that we are
using.
Here is one place I wasn't careful enough. If the wbio2 is not in
use, then it might get freed at the first generic_make_request call.
So perform all necessary tests first.
This bug was introduced in 3.3-rc3 (24afd80d99) and can cause an
oops, so fix is suitable for any -stable since then.
Cc: stable@vger.kernel.org (3.3+)
Signed-off-by: NeilBrown <neilb@suse.de>
Attached is Documentation/ja_JP/HOWTO sync patch for 3.10.
This patch was reviewed by Japanese translation community called JF.
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
build_skb() specifies that the data parameter must come from a kmalloc'd
area, this is only true if frag_size equals 0, because then build_skb()
will use kzsize(data) to figure out the actual data size. Update the
comment to reflect that special condition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ygWA
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The current timeout check is comparing two constant values, so it won't
ever detect a timeout. This patch reworks the affected code a bit so it
has a chance at detecting timeouts correctly.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the <= max condition in the for loop, it will be always go 1
element further than needed. If the condition for the while loop is
never met, then max is MAX_STAT_DEPTH, and for loop will walk off the
end of nodesizes[].
Signed-off-by: Jerry Snitselaar <jerry.snitselaar@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
