Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
result is always zero when comes here.
Signed-off-by: Yao Dongdong <yaodongdong@huawei.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull m68k update from Geert Uytterhoeven.
Just wiring up the bpf system call.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up bpf
A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd say.
Anyway, most of this are a few defconfig updates. Some for omap to deal
with kernel binary size (moving ipv6 to module, etc). A larger one for
socfpga that refreshes with some churn, but also turns on a few options
that makes the newly-added board in my bootfarm usable for testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot protocols,
hopefully encouraging those who still care about some of those platforms
to submit DT support and report bugs where needed. Nothing stops working
though, this is just to warn for future deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot hangs,
a missing terminting entry in a dt_match array on RealView a MTD fix on
OMAP with NAND.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JasG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver allocated on stack struct regulator_config but didn't initialize
it fully. Few fields (driver_data, ena_gpio) were left untouched. This
lead to using random ena_gpio values as GPIOs for max77693 regulators.
On occasion these values could match real GPIO numbers leading to
interfering with other drivers and to unsuccessful enable/disable of
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 80b022e29b ("regulator: max77693: Add max77693 regualtor driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
Adds the missing comparison for the RC_BIT_OTHER.
Cc: stable@vger.kernel.org # for Kernel 3.17
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change CONFIG_PM to CONFIG_PM_SLEEP to solve
warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 0d930e51cf ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
* Factor out code for clearing raised IRQs from exynos_tmu_work() to
exynos_tmu_clear_irqs().
* Add a comment about documentation bugs to exynos_tmu_clear_irqs().
[ The documentation for Exynos3250, Exynos4412, Exynos5250 and
Exynos5260 incorrectly states that INTCLEAR register has
a different placing of bits responsible for FALL IRQs than
INTSTAT register. Exynos5420 and Exynos5440 documentation is
correct (Exynos4210 doesn't support FALL IRQs at all). ]
* Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead
of open-coded code trying to clear IRQs according to predefined
masks. After this change exynos_tmu_initialize() just clears
IRQs that are raised like it is already done in exynos_tmu_work().
As a nice side-effect the code now uses the correct offset
(16 instead of 12) for bits responsible for clearing FALL IRQs
in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250.
* Remove no longer needed intclr_rise_[mask,shift] and
intclr_fall_[mask,shift] fields from struct exynos_tmu_registers.
* Remove no longer needed defines.
This patch has been tested on Exynos4412 and Exynos5420 SoCs.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here on function return all temporarily used device nodes shall
decrement their usage counter. The problems are found with device
nodes allocated by for_each_child_of_node(), of_parse_phandle()
and of_find_node_by_name(), fix all problems at once.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: devicetree@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch add support for TRIM_RELOAD feature at Exynos3250. The TMu of
Exynos3250 has two TRIMINFO_CON register and must need to set RELOAD bit
before reading TRIMINFO register.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch support many TRIMINFO_CTRL registers if specific Exynos SoC
has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD'
shift/mask bit operation to set RELOAD feature instead of static value.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently these SoCs claim TRIM_RELOAD support but don't have
triminfo_ctrl register address defined in their struct
exynos_tmu_registers entries. This causes incorrect write of
value "1" to data->base + 0x00 address (which happens to be
TRIMINFO register). Additionally according to the documentation
that I have neither Exynos5260 nor Exynos5420 support/require
TRIM_RELOAD feature. Thus fix the aforementioned issue by
removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and
Exynos5420.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need for abstracting configuration for registers that
are identical on all SoC types.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
pdata->reference_voltage and pdata->gain are always defined
to non-zero values so remove the redundant checks from
exynos_tmu_control().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Remove dead temp check from temp_to_code() (this function users
in exynos_tmu_initialize() always pass correct temperatures and
exynos_tmu_set_emulation() returns early for EXYNOS4210 because
TMU_SUPPORT_EMULATION flag is not set on this SoC).
* Move temp_code check from code_to_temp() to exynos_tmu_read()
(code_to_temp() only user).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for negative return values of temp_to_code()
from exynos_tmu_initialize().
The current level temperature data hardcoded in pdata will never
cause a negative temp_to_code() return values and checking itself
is not proper. The checks in question are done at runtime in
a production code for data that is hardcoded inside driver during
development time and later it doesn't change. Such data should
be verified during development and review time (i.e. by a script
parsing relevant data from exynos_tmu_data.c, one can also argue
that verification to be done is so simple that the review by
a maintainer should be enough).
Theres should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for pdata sanity from exynos_tmu_initialize().
The current values hardcoded in pdata will never trigger the checks
and checking itself is not proper. The checks in question are done
at runtime in a production code for data that is hardcoded inside
driver during development time and later it doesn't change. Such
data should be verified during development and review time (i.e. by
a script parsing relevant data from exynos_tmu_data.c, one can also
argue that verification to be done is so simple that the review by
a maintainer should be enough).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The commit 1928457 ("thermal: exynos: Add hardware mode thermal
calibration support") has added HW_MODE feature but it has never
been enabled. As such it has been a dead code for over a year
now and should be removed from the kernel.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused / write-only entries from struct exynos_tmu_registers.
Then remove unused defines while at it.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* A regression from 3.16 which was noticed in 3.17. With the restructuring of
the m25p80.c driver and the SPI NOR library framework, we omitted proper
listing of the SPI device IDs. This means m25p80.c wouldn't auto-load
(modprobe) properly when built as a module. For now, we duplicate the device
IDs into both modules.
* The OMAP / ELM modules were depending on an implicit link ordering. Use
deferred probing so that the new link order (in 3.18-rc) can still allow for
successful probing.
* Fix suspend/resume support for LH28F640BF NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxjM
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
This is a set of six patches consisting of two MAINTAINER updates, two scsi-mq
fixs for the old parallel interface (not every request is tagged and we need
to set the right flags to populate the SPI tag message) and a fix for a memory
leak in scatterlist traversal caused by a preallocation update in 3.17) and an
ipv6 fix for cxgbi.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUVqYyAAoJEDeqqVYsXL0MDwQIAI4aCdC3LUelt6IzywToiJ9u
GTUZU7eULzV1KuaExcBM8g9DyE3wtnhfS0WA5TqvfKf8ImMKntan0loK0juIjj8K
UBtbSDapwkKRRAIoRHvBzcHU+Jzc//naO95ojsFt2ELHB91jta368+DiPb8m+wQx
IKeYO6vFaSwZZCKVNaWwyCpxEKmMO+ib80zfuANBzWjau3IFxMiUofSvtPGIWb+E
Zxi9qvOyqjfFE8OLfL9ckH5NPiIYcwmarAXyuYcJstiw6VX2deGBaJalueSSC0JV
TAqEtT5k1AraFS2HM0TRxar+HK5iBj3s8f0pFBfgD2+oagUln6L/486nMh2Ktac=
=l6wS
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WvgB
-----END PGP SIGNATURE-----
Merge tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc2" from Tony Lindgren:
Few fixes for omaps to enable NAND BCH so devices won't
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
* tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (407 commits)
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
+ Linux 3.18-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
