Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Setting an MTU value below 68 was disabling the network connection and
would not reconnect until the driver was reloaded. Prevent changing the
MTU to anything below 68.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prevent Tx hangs from happening on 10Mb flood ping by increasing the
timeout factor.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The e1000e driver was based on a version of e1000 prior to acme's
introduction of skb_copy_to_linear_data_offset, and was submitted
after acme went through and coverted all the drivers to use it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.
The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Evgeniy Polyakov noticed that drivers/net/e1000e/netdev.c:e1000_netpoll()
was calling e1000_clean_tx_irq() without taking the TX lock.
David Miller suggested to remove the call altogether: since in this
callpah there's periodic calls to ->poll() anyway which will do
e1000_clean_tx_irq() and will garbage-collect any finished TX ring
descriptors.
This fix solved the e1000e+netconsole crashes i've been seeing:
=============================================================================
BUG skbuff_head_cache: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xf658ae9c-0xf658ae9c. First byte 0x6a instead of 0x6b
INFO: Allocated in __alloc_skb+0x2c/0x110 age=0 cpu=0 pid=5098
INFO: Freed in __kfree_skb+0x31/0x80 age=0 cpu=1 pid=4440
INFO: Slab 0xc16cc140 objects=16 used=1 fp=0xf658ae00 flags=0x400000c3
INFO: Object 0xf658ae00 @offset=3584 fp=0xf658af00
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes e1000e driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEH is not recovering in a reasonable amount of time on PPC during
e1000e_down().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The use of unsigned long causes the driver to fail on 32-bit systems
which support 64-bit resources.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.
This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).
To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with 2ports and 4ports pci-express e1000e
adapters.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.
Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several minor cosmetic function renames.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With multiple queues coming into the code these base control
registers need to be made into arrays.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reorganization moves the PHY status into a separate
struct. Flow Control setup is moved into this struct as well
and frame size away from here into the adapter struct where its
inly use is.
The post-link-up code is now a separate function and moved out
of the watchdog function itself. This allows us to track the
es2lan restart issue a bit easier.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename this function to be consistent with function naming (verb first)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adjusting the comment blocks here to be code-style compliant. no
code changes.
Changed some copyright dates to 2008.
Indentation fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
irq_sem can safely be removed by auditing all irq.*able sites to
make sure that interrupts don't get enabled unexpectedly when the
interface is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Users reported that ARP's were lost with e1000e. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRC stripping was only correctly enabled for packet split recieves
which is used when receiving jumbo frames. Correctly enable SECRC
also for normal buffer packet receives.
Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A logic mishap caused the adapter to keep link while we can
disable it due to WoL not being active, and vice versa.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's too much noise on systems that don't support MSI. Let's get rid
of a few and make the real error message more specific.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
napi_disable();
atomic_set(&adapter->irq_sem, 0);
*_irq_disable();
which makes sure the counter is always in the correct state.
Reported by Robert Olsson.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression added by changeset
53e52c729c ("[NET]: Make ->poll()
breakout consistent in Intel ethernet drivers.")
As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever. If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a cable unplug the forced flow control settings were lost
accidentally and the flow control settings fell back to the default
EEPROM determined values. This breaks for people who want to
run without fc enabled - after a cable reset the driver would
refuse to run with fc disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
