- Fix a compilation issue with User Mode Linux.
- Handle spurious interrupts properly in the PCA953x driver.
-----BEGIN PGP SIGNATURE-----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=yEo/
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late fixes: one IRQ issue and one compilation issue for UML.
- Fix a compilation issue with User Mode Linux
- Handle spurious interrupts properly in the PCA953x driver"
* tag 'gpio-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Survive spurious interrupts
gpiolib: Disable compat ->read() code in UML case
We can't check ref->data->confirm_switch directly in __percpu_ref_exit(), since
ref->data may not be allocated in one not-initialized refcount.
Fixes: 2b0d3d3e4f ("percpu_ref: reduce memory footprint of percpu_ref in fast path")
Reported-by: syzbot+fd15ff734dace9e16437@syzkaller.appspotmail.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
AMD Family 19h Models 20h-2Fh use the same PCI IDs as Family 17h Models
70h-7Fh. The same family ops and number of channels also apply.
Use the Family17h Model 70h family_type and ops for Family 19h Models
20h-2Fh. Update the controller name to match the system.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201009171803.3214354-1-Yazen.Ghannam@amd.com
- Assign a proper discard granularity rather than incorrectly set it to 0
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAl+ABO0XHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCkRwQ//cQ2cb3bb7ASbzKOCvm29Q3/c
u9ZfXH3Mg+GsP5htZOapO0PpHOMYohG8FpPe6NCAmVmdEGc6JhrjKX7xwGaoBOFX
SsUaRMO/5PjWJeCu6vzeBJCy2UJrDEYaBtQyL0U+/y84aNlmJ+74wACgG/dT6sgL
W/eejh5ynp/KMIkLQTZ3Ml1kNXJ77upDgN8npGCJXjG7PH9LsF5TwSrkV6PP96ML
4FoEDdM/QCRV7QloG+T1/yPDKExKiuQxLjsRqrdJIeoWb4otWLE1eTc5DveBMYwR
EZMbDTy4P+EBmhKB1BoM8PfDna/OxMnt4LAAYFKN5NzscI5YIb0my/smUtEINUKN
q/cFi+kMauHXMSchvTCGhmtXEXO/Gp0Eu6Eul3ouFKGlJLGw92J/P1nLoVRYeXf2
Z3gCdTMsLWQgIxY1dtZTJ0CCGaBVZUfUwFiRC0GfduWZsAa1ihn3IByaPcLNhgMY
vxSrjCFJPP+f13LG4hBwko+S+LWomY0+1U7sDmPBinh3EdVPM507yE9/nf1/U17Q
sTd6izhwm8WKIBW6S0m06LIMpt42ED0Za2m8fWnyBiUnSG4Xh+cH9fDF8TxzYP2F
Q/JZlC5nA0thdK3wlbgE2eMxC1xZdpPhyaOxU7kw0vct1IC01W7q+zViy2bTp3WI
jOP0LPH0uqk8mh/Rttk=
=S62I
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"Assign a proper discard granularity rather than incorrectly set it to
zero"
* tag 'mmc-v5.9-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: don't set limits.discard_granularity as 0
amdgpu:
- Fix a crash on renoir if you override the IP discovery parameter
- Fix the build on ARC platforms
- Display fix for Sienna Cichlid
-----BEGIN PGP SIGNATURE-----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=EI05
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2020-10-09' of git://anongit.freedesktop.org/drm/drm
Pull amdgpu drm fixes from Dave Airlie:
"Fixes trickling in this week.
Alex had a final fix for the newest GPU they introduced in rc1, along
with one build regression and one crasher fix.
Cross my fingers that's it for 5.9:
- Fix a crash on renoir if you override the IP discovery parameter
- Fix the build on ARC platforms
- Display fix for Sienna Cichlid"
* tag 'drm-fixes-2020-10-09' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Change ABM config init interface
drm/amdgpu/swsmu: fix ARC build errors
drm/amdgpu: fix NULL pointer dereference for Renoir
sysfs-pci and sysfs-tagging were mis-filed: their locations within
Documentation/ implied that they were related to file systems. Actually,
each topic is about a very specific *use* of sysfs, and sysfs *happens*
to be a (virtual) filesystem, so this is not really the right place.
It's jarring to be reading about filesystems in general and then come
across these specific details about PCI, and tagging...and then back to
general filesystems again.
Move sysfs-pci to PCI, and move sysfs-tagging to networking. (Thanks to
Jonathan Corbet for coming up with the final locations.)
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/20201009070128.118639-1-jhubbard@nvidia.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This reverts commit 353e228eb3.
Qian Cai reports that TX2 no longer boots with his .config as it appears
that task_cpu() gets instrumented and used before KASAN has been
initialised.
Although Mark has a proposed fix, let's take the safe option of reverting
this for now and sorting it out properly later.
Link: https://lore.kernel.org/r/711bc57a314d8d646b41307008db2845b7537b3d.camel@redhat.com
Reported-by: Qian Cai <cai@redhat.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Pull KCSAN updates for v5.10 from Paul E. McKenney:
- Improve kernel messages.
- Be more permissive with bitops races under KCSAN_ASSUME_PLAIN_WRITES_ATOMIC=y.
- Optimize debugfs stat counters.
- Introduce the instrument_*read_write() annotations, to provide a
finer description of certain ops - using KCSAN's compound instrumentation.
Use them for atomic RNW and bitops, where appropriate.
Doing this might find new races.
(Depends on the compiler having tsan-compound-read-before-write=1 support.)
- Support atomic built-ins, which will help certain architectures, such as s390.
- Misc enhancements and smaller fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The thinking in commit:
fddf9055a6 ("lockdep: Use raw_cpu_*() for per-cpu variables")
is flawed. While it is true that when we're migratable both CPUs will
have a 0 value, it doesn't hold that when we do get migrated in the
middle of a raw_cpu_op(), the old CPU will still have 0 by the time we
get around to reading it on the new CPU.
Luckily, the reason for that commit (s390 using preempt_disable()
instead of preempt_disable_notrace() in their percpu code), has since
been fixed by commit:
1196f12a2c ("s390: don't trace preemption in percpu macros")
An audit of arch/*/include/asm/percpu*.h shows there are no other
architectures affected by this particular issue.
Fixes: fddf9055a6 ("lockdep: Use raw_cpu_*() for per-cpu variables")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20201005095958.GJ2651@hirez.programming.kicks-ass.net
Steve reported that lockdep_assert*irq*(), when nested inside lockdep
itself, will trigger a false-positive.
One example is the stack-trace code, as called from inside lockdep,
triggering tracing, which in turn calls RCU, which then uses
lockdep_assert_irqs_disabled().
Fixes: a21ee6055c ("lockdep: Change hardirq{s_enabled,_context} to per-cpu variables")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Basically print_lock_class_header()'s for loop is out of sync with the
the size of of ->usage_traces[].
Also clean things up a bit while at it, to avoid such mishaps in the future.
Fixes: 23870f1227 ("locking/lockdep: Fix "USED" <- "IN-NMI" inversions")
Reported-by: Qian Cai <cai@redhat.com>
Debugged-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Qian Cai <cai@redhat.com>
Link: https://lkml.kernel.org/r/20200930094937.GE2651@hirez.programming.kicks-ass.net
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294
CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1
Hardware name: Google Kevin (DT)
pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
pc : __blkdev_issue_discard+0x200/0x294
lr : __blkdev_issue_discard+0x54/0x294
sp : ffff800011dd3b10
x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace:
__blkdev_issue_discard+0x200/0x294
__submit_discard_cmd+0x128/0x374
__issue_discard_cmd_orderly+0x188/0x244
__issue_discard_cmd+0x2e8/0x33c
issue_discard_thread+0xe8/0x2f0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
---[ end trace e4c8023d33dfe77a ]---
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b6 ("mmc: queue: let host controllers specify maximum discard timeout")
Fixes: b35fd7422c ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()").
Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error handling introduced by commit:
2ed6edd33a ("perf: Add cond_resched() to task_function_call()")
looses any return value from smp_call_function_single() that is not
{0, -EINVAL}. This is a problem because it will return -EXNIO when the
target CPU is offline. Worse, in that case it'll turn into an infinite
loop.
Fixes: 2ed6edd33a ("perf: Add cond_resched() to task_function_call()")
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Barret Rhoden <brho@google.com>
Tested-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20200827064732.20860-1-kjain@linux.ibm.com
-----BEGIN PGP SIGNATURE-----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=THH6
-----END PGP SIGNATURE-----
Merge tag 'block5.9-2020-10-08' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes that should go into this release:
- NVMe controller error path reference fix (Chaitanya)
- Fix regression with IBM partitions on non-dasd devices (Christoph)
- Fix a missing clear in the compat CDROM packet structure (Peilin)"
* tag 'block5.9-2020-10-08' of git://git.kernel.dk/linux-block:
partitions/ibm: fix non-DASD devices
nvme-core: put ctrl ref when module ref get fail
block/scsi-ioctl: Fix kernel-infoleak in scsi_put_cdrom_generic_arg()
Looks like the I2C tunnel implementation from Chromebook's
embedded controller does not handle PEC correctly. Fix this
by disabling PEC for batteries behind those I2C tunnels as
a workaround.
Note, that some Chromebooks actually have been reported to
have working PEC support (with I2C tunnel). Since the problem
has not yet been fully understood this simply reverts all
Chromebooks to not use PEC for now.
Reported-by: "Milan P. Stanić" <mps@arvanta.net>
Reported-by: Vicente Bergas <vicencb@gmail.com>
CC: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 7222bd603d ("power: supply: sbs-battery: add PEC support")
Tested-by: Vicente Bergas <vicencb@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
These controllers are based on the DW APB SSI IP-core and embedded into
the SoC, so two of them are equipped with IRQ, DMA, 64 words FIFOs and 4
native CS, while another one as being utilized by the Baikal-T1 System
Boot Controller has got a very limited resources: no IRQ, no DMA, only a
single native chip-select and just 8 bytes Tx/Rx FIFOs available. That's
why we have to mark the IRQ to be optional for the later interface.
The SPI controller embedded into the Baikal-T1 System Boot Controller can
be also used to directly access an external SPI flash by means of a
dedicated FSM. The corresponding MMIO region availability is switchable by
the embedded multiplexor, which phandle can be specified in the dts node.
* We added a new example to test out the non-standard Baikal-T1 System
Boot SPI Controller DT binding.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201007235511.4935-21-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 is equipped with three DW APB SSI-based MMIO SPI controllers.
Two of them are pretty much normal: with IRQ, DMA, FIFOs of 64 words
depth, 4x CSs, but the third one as being a part of the Baikal-T1 System
Boot Controller has got a very limited resources: no IRQ, no DMA, only a
single native chip-select and Tx/Rx FIFO with just 8 words depth
available. In order to provide a transparent initial boot code execution
the Boot SPI controller is also utilized by an vendor-specific IP-block,
which exposes an SPI flash direct mapping interface. Since both direct
mapping and SPI controller normal utilization are mutual exclusive only
one of these interfaces can be used to access an external SPI slave
device. That's why a dedicated mux is embedded into the System Boot
Controller. All of that is taken into account in the Baikal-T1-specific DW
APB SSI glue driver implemented by means of the DW SPI core module.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-22-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
A functionality of the poll-based transfer has been removed by
commit 1ceb09717e98 ("spi: dw: remove cs_control and poll_mode members
from chip_data") with a justification that "there is no user of one
anymore". It turns out one of our DW APB SSI core is synthesized with no
IRQ line attached and the only possible way of using it is to implement a
poll-based SPI transfer procedure. So we have to get the removed
functionality back, but with some alterations described below.
First of all the poll-based transfer is activated only if the DW SPI
controller doesn't have an IRQ line attached and the Linux IRQ number is
initialized with the IRQ_NOTCONNECTED value. Secondly the transfer
procedure is now executed with a delay performed between writer and reader
methods. The delay value is calculated based on the number of data words
expected to be received on the current iteration. Finally the errors
status is checked on each iteration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In some circumstances the current implementation of the SPI memory
operations may occasionally fail even though they are executed in the
atomic context. This may happen if the system bus is relatively slow in
comparison to the SPI bus frequency, or there is a concurrent access to
it, which makes the MMIO-operations occasionally stalling before
push-pulling data from the DW APB SPI FIFOs. These two problems we've
discovered on the Baikal-T1 SoC. In order to fix them we have no choice
but to set an artificial limitation on the SPI bus speed.
Note currently this limitation will be only applicable for the memory
operations, since the standard SPI core interface is implemented with an
assumption that there is no problem with the automatic CS toggling.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from the synchronous Tx-Rx mode, which has been utilized to create
the normal SPI transfers in the framework of the DW SSI driver, DW SPI
controller supports Tx-only and EEPROM-read modes. The former one just
enables the controller to transmit all the data from the Tx FIFO ignoring
anything retrieved from the MISO lane. The later mode is so called
write-then-read operation: DW SPI controller first pushes out all the data
from the Tx FIFO, after that it'll automatically receive as much data as
has been specified by means of the CTRLR1 register. Both of those modes
can be used to implement the memory operations supported by the SPI-memory
subsystem.
The memory operation implementation is pretty much straightforward, except
a few peculiarities we have had to take into account to make things
working. Since DW SPI controller doesn't provide a way to directly set and
clear the native CS lane level, but instead automatically de-asserts it
when a transfer going on, we have to make sure the Tx FIFO isn't empty
during entire Tx procedure. In addition we also need to read data from the
Rx FIFO as fast as possible to prevent it' overflow with automatically
fetched incoming traffic. The denoted peculiarities get to cause even more
problems if DW SSI controller is equipped with relatively small FIFO and
is connected to a relatively slow system bus (APB) (with respect to the
SPI bus speed). In order to workaround the problems for as much as it's
possible, the memory operation execution procedure collects all the Tx
data into a single buffer and disables the local IRQs to speed the
write-then-optionally-read method up.
Note the provided memory operations are utilized by default only if
a glue driver hasn't provided a custom version of ones and this is not
a DW APB SSI controller with fixed automatic CS toggle functionality.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The DW SSI errors handling method can be generically implemented for all
types of the transfers: IRQ, DMA and poll-based ones. It will be a
function which checks the overflow/underflow error flags and resets the
controller if any of them is set. In the framework of this commit we make
use of the new method to detect the errors in the IRQ- and DMA-based SPI
transfer execution procedures.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The parameter will be needed for another wait-done method being added in
the framework of the SPI memory operation modification in a further
commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
By design of the currently available native set_cs callback, the CS
de-assertion will be done only if it's required by the corresponding
controller capability. But in order to pre-fill the Tx FIFO buffer with
data during the SPI memory ops execution the SER register needs to be left
cleared before that. We'll also need a way to explicitly set and clear the
corresponding CS bit at a certain moment of the operation. Let's alter
the set_cs function then to also de-activate the CS, when it's required.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI memory operations implementation will require to have the CS register
cleared before executing the operation in order not to have the
transmission automatically started prior the Tx FIFO is pre-initialized.
Let's clear the register then on explicit controller reset to fulfil the
requirements in case of an error or having the CS left set by a bootloader
or another software.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's pointless to enable the chip back if the DMA setup procedure fails,
since we'll disable it on the next transfer anyway. For the same reason We
don't do that in case of a failure detected in any other methods called
from the transfer_one() method.
While at it consider any non-zero value returned from the dma_setup
callback to be erroneous as it's supposed to be in the kernel.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's theoretically erroneous to enable IRQ before the chip is turned on.
If IRQ handler gets executed before the chip is enabled, then any data
written to the Tx FIFO will be just ignored.
I say "theoretically" because we haven't noticed any problem with that,
but let's fix it anyway just in case...
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make the transfer_one() callback method more readable and
for unification with the DMA-based transfer, let's detach the IRQ setup
procedure into a dedicated function. While at it rename the IRQ-based
transfer handler function to be dw_spi-prefixe and looking more like the
DMA-related one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Current IRQ-based SPI transfer execution procedure doesn't work well at
the final stage of the execution. If all the Tx data is sent out (written
to the Tx FIFO) but there is some data left to receive, the Tx FIFO Empty
IRQ will constantly happen until all of the requested inbound data is
received. Though for a short period of time, but it will make the system
less responsive. In order to fix that let's refactor the SPI transfer
execution procedure by taking the Rx FIFO Full IRQ into account. We'll read
and write SPI transfer data each time the IRQ happens as before. If all
the outbound data is sent out, we'll disable the Tx FIFO Empty IRQ. If
there is still some data to receive, we'll adjust the Rx FIFO Threshold
level, so the next IRQ would be raised at the moment of all incoming data
being available in the Rx FIFO.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The Tx and Rx data write/read procedure can be significantly simplified by
using Tx/Rx transfer lengths instead of the end pointers. By having the
Tx/Rx data leftover lengths (in the number of transfer words) we can get
rid of all subtraction and division operations utilized here and there in
the tx_max(), rx_max(), dw_writer() and dw_reader() methods. Such
modification will not only give us the more optimized IO procedures, but
will make the data IO methods much more readable than before.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI controller can be used by the two SPI core interfaces:
traditional SPI transfers and SPI memory operations. The controller needs
to be accordingly configured at runtime when the corresponding operations
are executed. In order to do that for the both interfaces from a single
function we introduce a new data wrapper for the transfer mode, data
width, number of data frames (for the automatic data transfer) and the bus
frequency. It will be used by the update_config() method to tune the DW
APB SSI up.
The update_config() method is made exported to be used not only by the DW
SPI core driver, but by the glue layer drivers too. This will be required
in a coming further commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Rx sample delay can be SPI device specific, and should be synchronously
initialized with the rest of the communication and peripheral device
related controller setups. So let's move the Rx-sample delay setup into
the DW APB SSI configuration update method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The code currently responsible for the SPI communication speed setting up
is a bit messy. Most likely for some historical reason the bus frequency
is saved in the peripheral chip private data. It's pointless now since the
custom communication speed is a SPI-transfer-specific thing and only if
there is no SPI transfer data specified (like during the SPI memory
operations) it can be taken from the SPI device structure. But even in the
later case there is no point in having the clock divider and the SPI bus
frequency saved in the chip data, because the controller can be used for
both SPI-transfer-based and SPI-transfer-less communications. From
software point of view keeping the current clock divider in an SPI-device
specific storage may give a small performance gain (to avoid sometimes a
round-up division), but in comparison to the total SPI transfer time it
just doesn't worth saving a few CPU cycles in comparison to the total SPI
transfer time while having the harder to read code. The only optimization,
which could worth preserving in the code is to avoid unnecessary DW SPI
controller registers update if it's possible. So to speak let's simplify
the SPI communication speed update procedure by removing the clock-related
fields from the peripheral chip data and update the DW SPI clock divider
only if it's really changed. The later change is reached by keeping the
effective SPI bus speed in the internal DW SPI private data.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI bus speed update functionality will be useful in another parts of
the driver too (like to implement the SPI memory operations and from the
DW SPI glue layers). Let's move it to the update_cr0() method then and
since the later is now updating not only the CTRLR0 register alter its
prototype to have a generic function name not related to CR0.
Leave the too long line with the chip->clk_div setting as is for now,
since it's going to be changed later anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Indeed there is no point in detecting the SPI peripheral device parameters
and initializing the CR0 register fields each time an SPI transfer is
executed. Instead let's define a dedicated CR0 chip-data member, which
will be initialized in accordance with the SPI device settings at the
moment of setting it up.
By doing so we'll finally make the SPI device chip_data serving as it's
supposed to - to preserve the SPI device specific DW SPI configuration.
See spi-fsl-dspi.c, spi-pl022.c, spi-pxa2xx.c drivers for example of the
way the chip data is utilized.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DWC SSI core is supported by means of setting up the
core-specific update_cr0() callback. It isn't suitable for multiple
reasons. First of all having exported several methods doing the same thing
but for different chips makes the code harder to maintain. Secondly the
spi-dw-core driver exports the methods, then the spi-dw-mmio driver sets
the private data callback with one of them so to be called by the core
driver again. That makes the code logic too complicated. Thirdly using
callbacks for just updating the CR0 register is problematic, since in case
if the register needed to be updated from different parts of the code,
we'd have to create another callback (for instance the SPI device-specific
parameters don't need to be calculated each time the SPI transfer is
submitted, so it's better to pre-calculate the CR0 data at the SPI-device
setup stage).
So keeping all the above in mind let's discard the update_cr0() callbacks,
define a generic and static dw_spi_update_cr0() method and create the
DW_SPI_CAP_DWC_SSI capability, which when enabled would activate the
alternative CR0 register layout.
While at it add the comments to the code path of the normal DW APB SSI
controller setup to make the dw_spi_update_cr0() method looking coherent.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the dw_spi_add_host() method a bit by replacing the currently
implemented default set_cs callback setting up and later having it
overwritten by a custom function with direct if-else-based callback
assignment.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Some last minute fixes. The last two of them haven't been in next but
they do seem kind of obvious, very small and safe, fix bugs reported in
the field, and they are both in a new mlx5 vdpa driver, so it's not like
we can introduce regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl9/cWEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpaPoH/2b+Hc0UvQPvAas1uWC022bV/VpfiW0+OZaT
IsP88s9IInjWUoBb7Rqkhi3jnZYs9p7W59AV9cNJ5g6vPxcxrJAfgeo9R4bq6rD9
LqIAxHRRwPEnYddtFAv/XnX4YuTS+cJFwFJLWGXXdySA5/pgFqc9qDXjNLFzxq7X
8pI7qbW04e9eS3i8vlZwXNHpHQ7DMcpgewR7XO1Lhqh4sHWfusKSEVDrOM7v/0ru
yMtwKA5X8vRZQTIoaLamRWIm/qLWIi/Wcor6APhRG0Hn9yzS21JRnGDs8iKRSjjx
ecBNatgGPrmbO7yCfyh4el0GgrYhxAk/w2H3p/aXQJu+sGXL8nk=
=y/Tb
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost fixes from Michael Tsirkin:
"Some last minute vhost,vdpa fixes.
The last two of them haven't been in next but they do seem kind of
obvious, very small and safe, fix bugs reported in the field, and they
are both in a new mlx5 vdpa driver, so it's not like we can introduce
regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix dependency on MLX5_CORE
vdpa/mlx5: should keep avail_index despite device status
vhost-vdpa: fix page pinning leakage in error path
vhost-vdpa: fix vhost_vdpa_map() on error condition
vhost: Don't call log_access_ok() when using IOTLB
vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
vhost: Don't call access_ok() when using IOTLB
vhost vdpa: fix vhost_vdpa_open error handling
[Why & How]
change abm config init interface to support multiple ABMs.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull networking fixes from Jakub Kicinski:
"One more set of fixes from the networking tree:
- add missing input validation in nl80211_del_key(), preventing
out-of-bounds access
- last minute fix / improvement of a MRP netlink (uAPI) interface
introduced in 5.9 (current) release
- fix "unresolved symbol" build error under CONFIG_NET w/o
CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
BTF.
- fix 32 bit sub-register bounds tracking in the bpf verifier for OR
case
- tcp: fix receive window update in tcp_add_backlog()
- openvswitch: handle DNAT tuple collision in conntrack-related code
- r8169: wait for potential PHY reset to finish after applying a FW
file, avoiding unexpected PHY behaviour and failures later on
- mscc: fix tail dropping watermarks for Ocelot switches
- avoid use-after-free in macsec code after a call to the GRO layer
- avoid use-after-free in sctp error paths
- add a device id for Cellient MPL200 WWAN card
- rxrpc fixes:
- fix the xdr encoding of the contents read from an rxrpc key
- fix a BUG() for a unsupported encoding type.
- fix missing _bh lock annotations.
- fix acceptance handling for an incoming call where the incoming
call is encrypted.
- the server token keyring isn't network namespaced - it belongs
to the server, so there's no need. Namespacing it means that
request_key() fails to find it.
- fix a leak of the server keyring"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
net: usb: qmi_wwan: add Cellient MPL200 card
macsec: avoid use-after-free in macsec_handle_frame()
r8169: consider that PHY reset may still be in progress after applying firmware
openvswitch: handle DNAT tuple collision
sctp: fix sctp_auth_init_hmacs() error path
bridge: Netlink interface fix.
net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
bpf: Fix scalar32_min_max_or bounds tracking
tcp: fix receive window update in tcp_add_backlog()
net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
mptcp: more DATA FIN fixes
net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
rxrpc: Fix server keyring leak
rxrpc: The server keyring isn't network-namespaced
rxrpc: Fix accept on a connection that need securing
rxrpc: Fix some missing _bh annotations on locking conn->state_lock
rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
rxrpc: Fix rxkad token xdr encoding
...
The dev_t is defined in types.h while struct gpio_device forward declaration
is missed. Take into account above and update header block in gpiolib-cdev.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201005095622.73616-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use kstrndup() to copy line labels from the userspace provided char
array, rather than ensuring the char array contains a null terminator
and using kstrdup().
Note that the length provided to kstrndup() still assumes that the char
array does contain a null terminator, so the maximum string length is one
less than the array. This is consistent with the previous behaviour.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20201005070246.20927-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>