Tracking of dirty pages in shared writeable mmap()s.
The idea is simple: write protect clean shared writeable pages, catch the
write-fault, make writeable and set dirty. On page write-back clean all the
PTE dirty bits and write protect them once again.
The implementation is a tad harder, mainly because the default
backing_dev_info capabilities were too loosely maintained. Hence it is not
enough to test the backing_dev_info for cap_account_dirty.
The current heuristic is as follows, a VMA is eligible when:
- its shared writeable
(vm_flags & (VM_WRITE|VM_SHARED)) == (VM_WRITE|VM_SHARED)
- it is not a 'special' mapping
(vm_flags & (VM_PFNMAP|VM_INSERTPAGE)) == 0
- the backing_dev_info is cap_account_dirty
mapping_cap_account_dirty(vma->vm_file->f_mapping)
- f_op->mmap() didn't change the default page protection
Page from remap_pfn_range() are explicitly excluded because their COW
semantics are already horrid enough (see vm_normal_page() in do_wp_page()) and
because they don't have a backing store anyway.
mprotect() is taught about the new behaviour as well. However it overrides
the last condition.
Cleaning the pages on write-back is done with page_mkclean() a new rmap call.
It can be called on any page, but is currently only implemented for mapped
pages, if the page is found the be of a VMA that accounts dirty pages it will
also wrprotect the PTE.
Finally, in fs/buffers.c:try_to_free_buffers(); remove clear_page_dirty() from
under ->private_lock. This seems to be safe, since ->private_lock is used to
serialize access to the buffers, not the page itself. This is needed because
clear_page_dirty() will call into page_mkclean() and would thereby violate
locking order.
[dhowells@redhat.com: Provide a page_mkclean() implementation for NOMMU]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a VM_BUG_ON, which is turned on with CONFIG_DEBUG_VM. Use this
in the lightweight, inline refcounting functions; PageLRU and PageActive
checks in vmscan, because they're pretty well confined to vmscan. And in
page allocate/free fastpaths which can be the hottest parts of the kernel
for kbuilds.
Unlike BUG_ON, VM_BUG_ON must not be used to execute statements with
side-effects, and should not be used outside core mm code.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stops panic associated with attempting to free a non slab-allocated
per_cpu_pageset.
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes up a couple of conflicts when merging up with
Linus' latest kernel. This will hopefully allow GFS2 to
be more easily merged into forthcoming -mm and FC kernels
due to the "one line per header" format now used for the
kernel headers.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Conflicts:
include/linux/Kbuild
include/linux/kernel.h
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (74 commits)
NFS: unmark NFS direct I/O as experimental
NFS: add comments clarifying the use of nfs_post_op_update()
NFSv4: rpc_mkpipe creating socket inodes w/out sk buffers
NFS: Use SEEK_END instead of hardcoded value
NFSv4: When mounting with a port=0 argument, substitute port=2049
NFSv4: Poll more aggressively when handling NFS4ERR_DELAY
NFSv4: Handle the condition NFS4ERR_FILE_OPEN
NFSv4: Retry lease recovery if it failed during a synchronous operation.
NFS: Don't invalidate the symlink we just stuffed into the cache
NFS: Make read() return an ESTALE if the file has been deleted
NFSv4: It's perfectly legal for clp to be NULL here....
NFS: nfs_lookup - don't hash dentry when optimising away the lookup
SUNRPC: Fix Oops in pmap_getport_done
SUNRPC: Add refcounting to the struct rpc_xprt
SUNRPC: Clean up soft task error handling
SUNRPC: Handle ENETUNREACH, EHOSTUNREACH and EHOSTDOWN socket errors
SUNRPC: rpc_delay() should not clobber the rpc_task->tk_status
Fix a referral error Oops
NFS: NFS_ROOT should use the new rpc_create API
NFS: Fix up compiler warnings on 64-bit platforms in client.c
...
Manually resolved conflict in net/sunrpc/xprtsock.c
The grow algorithm is simple, we grow if:
1) we see a hash chain collision at insert, and
2) we haven't hit the hash size limit (currently 1*1024*1024 slots), and
3) the number of xfrm_state objects is > the current hash mask
All of this needs some tweaking.
Remove __initdata from "hashdist" so we can use it safely at run time.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a CPU faults this page into pagetables after invalidate_mapping_pages()
checked page_mapped(), invalidate_complete_page() will still proceed to remove
the page from pagecache. This leaves the page-faulting process with a
detached page. If it was MAP_SHARED then file data loss will ensue.
Fix that up by checking the page's refcount after taking tree_lock.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents cross-region mappings on IA64 and SPARC which could lead
to system crash. They were correctly trapped for normal mmap() calls,
but not for the kernel internal calls generated by executable loading.
This code just moves the architecture-specific cross-region checks into
an arch-specific "arch_mmap_check()" macro, and defines that for the
architectures that needed it (ia64, sparc and sparc64).
Architectures that don't have any special requirements can just ignore
the new cross-region check, since the mmap() code will just notice on
its own when the macro isn't defined.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Cleaned up to not affect architectures that don't need it ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since vma->vm_pgoff is in units of smallpages, VMAs for huge pages have the
lower HPAGE_SHIFT - PAGE_SHIFT bits always cleared, which results in badd
offsets to the interleave functions. Take this difference from small pages
into account when calculating the offset. This does add a 0-bit shift into
the small-page path (via alloc_page_vma()), but I think that is negligible.
Also add a BUG_ON to prevent the offset from growing due to a negative
right-shift, which probably shouldn't be allowed anyways.
Tested on an 8-memory node ppc64 NUMA box and got the interleaving I
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch works around a complex dm-related deadlock/livelock down in the
mempool allocator.
Alasdair said:
Several dm targets suffer from this.
Mempools are not yet used correctly everywhere in device-mapper: they can
get shared when devices are stacked, and some targets share them across
multiple instances. I made fixing this one of the prerequisites for this
patch:
md-dm-reduce-stack-usage-with-stacked-block-devices.patch
which in some cases makes people more likely to hit the problem.
There's been some progress on this recently with (unfinished) dm-crypt
patches at:
http://www.kernel.org/pub/linux/kernel/people/agk/patches/2.6/editing/
(dm-crypt-move-io-to-workqueue.patch plus dependencies)
and:
I've no problems with a temporary workaround like that, but Milan Broz (a
new Redhat developer in the Czech Republic) has started reviewing all the
mempool usage in device-mapper so I'm expecting we'll soon have a proper fix
for this associated problems. [He's back from holiday at the start of next
week.]
For now, this sad-but-safe little patch will allow the machine to recover.
[akpm@osdl.org: rewrote changelog]
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ZVC counter update threshold is currently set to a fixed value of 32.
This patch sets up the threshold depending on the number of processors and
the sizes of the zones in the system.
With the current threshold of 32, I was able to observe slight contention
when more than 130-140 processors concurrently updated the counters. The
contention vanished when I either increased the threshold to 64 or used
Andrew's idea of overstepping the interval (see ZVC overstep patch).
However, we saw contention again at 220-230 processors. So we need higher
values for larger systems.
But the current default is already a bit of an overkill for smaller
systems. Some systems have tiny zones where precision matters. For
example i386 and x86_64 have 16M DMA zones and either 900M ZONE_NORMAL or
ZONE_DMA32. These are even present on SMP and NUMA systems.
The patch here sets up a threshold based on the number of processors in the
system and the size of the zone that these counters are used for. The
threshold should grow logarithmically, so we use fls() as an easy
approximation.
Results of tests on a system with 1024 processors (4TB RAM)
The following output is from a test allocating 1GB of memory concurrently
on each processor (Forking the process. So contention on mmap_sem and the
pte locks is not a factor):
X MIN
TYPE: CPUS WALL WALL SYS USER TOTCPU
fork 1 0.552 0.552 0.540 0.012 0.552
fork 4 0.552 0.548 2.164 0.036 2.200
fork 16 0.564 0.548 8.812 0.164 8.976
fork 128 0.580 0.572 72.204 1.208 73.412
fork 256 1.300 0.660 310.400 2.160 312.560
fork 512 3.512 0.696 1526.836 4.816 1531.652
fork 1020 20.024 0.700 17243.176 6.688 17249.863
So a threshold of 32 is fine up to 128 processors. At 256 processors contention
becomes a factor.
Overstepping the counter (earlier patch) improves the numbers a bit:
fork 4 0.552 0.548 2.164 0.040 2.204
fork 16 0.552 0.548 8.640 0.148 8.788
fork 128 0.556 0.548 69.676 0.956 70.632
fork 256 0.876 0.636 212.468 2.108 214.576
fork 512 2.276 0.672 997.324 4.260 1001.584
fork 1020 13.564 0.680 11586.436 6.088 11592.523
Still contention at 512 and 1020. Contention at 1020 is down by a third.
256 still has a slight bit of contention.
After this patch the counter threshold will be set to 125 which reduces
contention significantly:
fork 128 0.560 0.548 69.776 0.932 70.708
fork 256 0.636 0.556 143.460 2.036 145.496
fork 512 0.640 0.548 284.244 4.236 288.480
fork 1020 1.500 0.588 1326.152 8.892 1335.044
[akpm@osdl.org: !SMP build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increments and decrements are usually grouped rather than mixed. We can
optimize the inc and dec functions for that case.
Increment and decrement the counters by 50% more than the threshold in
those cases and set the differential accordingly. This decreases the need
to update the atomic counters.
The idea came originally from Andrew Morton. The overstepping alone was
sufficient to address the contention issue found when updating the global
and the per zone counters from 160 processors.
Also remove some code in dec_zone_page_state.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a bug in mm/swapfile.c#swap_type_of() that makes swsusp only be
able to use the first active swap partition as the resume device. Fix it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hugh Dickins <hugh@veritas.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't let fuse_readpages leave the @pages list not empty when exiting
on error.
[akpm@osdl.org: kernel-doc fixes]
Signed-off-by: Alexander Zarochentsev <zam@namesys.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for collision check enhancement for memory hot add.
It's better to do resouce collision check before doing memory hot add,
which will touch memory management structures.
And add_section() should check section exists or not before calling
sparse_add_one_section(). (sparse_add_one_section() will do another
check anyway. but checking in memory_hotplug.c will be easy to understand.)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: keith mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
find_next_system_ram() is used to find available memory resource at onlining
newly added memory. This patch fixes following problem.
find_next_system_ram() cannot catch this case.
Resource: (start)-------------(end)
Section : (start)-------------(end)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioresouce handling code in memory hotplug allows not-aligned memory hot add.
But when memmap and other memory structures are initialized, parameters should
be aligned. (if not aligned, initialization of mem_map will do wrong, it
assumes parameters are aligned.) This patch fix it.
And this patch allows ioresource collision check to handle -EEXIST.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The POSIX_FADV_NOREUSE hint means "the application will use this range of the
file a single time". It seems to be intended that the implementation will use
this hint to perform drop-behind of that part of the file when the application
gets around to reading or writing it.
However for reasons which aren't obvious (or sane?) I mapped
POSIX_FADV_NOREUSE onto POSIX_FADV_WILLNEED. ie: it does readahead.
That's daft. So for now, make POSIX_FADV_NOREUSE a no-op.
This is a non-back-compatible change. If someone was using POSIX_FADV_NOREUSE
to perform readahead, they lose. The likelihood is low.
If/when we later implement POSIX_FADV_NOREUSE things will get interesting - to
do it fully we'll need to maintain file offset/length ranges and peform all
sorts of complex tricks, and managing the lifetime of those ranges' data
structures will be interesting..
A sensible implementation would probably ignore the file range and would
simply mark the entire file as needing some form of drop-behind treatment.
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kmem_cache_alloc() was documented twice, but kmem_cache_zalloc() never.
Fix this obvious typo to get things right.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few of the callback functions and notifier blocks that are associated with cpu
notifications incorrectly have __devinit and __devinitdata. They should be
__cpuinit and __cpuinitdata instead.
It makes no functional difference but wastes text area when CONFIG_HOTPLUG is
enabled and CONFIG_HOTPLUG_CPU is not.
This patch fixes all those instances.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For some reason it triggers always with NFS root and spams the kernel
logs of my nfs root boxes a lot.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AGP keeps its own copy of the protection_map, upcoming DRM changes will
also require access to this map from modules.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Dave Jones <davej@redhat.com>
As per comments received, alter the GFS2 direct I/O path so that
it uses the standard read functions "out of the box". Needs a
small change to one of the VFS functions. This reduces the size
of the code quite a lot and also removes the need for one new export.
Some more work remains to be done, but this is the bones of the
thing.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Unlike earlier iterations of the delay accounting patches, now delays are only
collected for the actual I/O waits rather than try and cover the delays seen
in I/O submission paths.
Account separately for block I/O delays incurred as a result of swapin page
faults whose frequency can be affected by the task/process' rss limit. Hence
swapin delays can act as feedback for rss limit changes independent of I/O
priority changes.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nommu.c needs to export two more symbols for drivers to use:
remap_pfn_range and unmap_mapping_range.
Signed-off-by: Luke Yang <luke.adi@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a race condition that showed up in a threaded JIT environment.
The situation is that a process with a JIT code page forks, so the page is
marked read-only, then some threads are created in the child. One of the
threads attempts to add a new code block to the JIT page, so a
copy-on-write fault is taken, and the kernel allocates a new page, copies
the data, installs the new pte, and then calls lazy_mmu_prot_update() to
flush caches to make sure that the icache and dcache are in sync.
Unfortunately, the other thread runs right after the new pte is installed,
but before the caches have been flushed. It tries to execute some old JIT
code that was already in this page, but it sees some garbage in the i-cache
from the previous users of the new physical page.
Fix: we must make the caches consistent before installing the pte. This is
an ia64 only fix because lazy_mmu_prot_update() is a no-op on all other
architectures.
Signed-off-by: Anil Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__vunmap must not rely on area->nr_pages when picking the release methode
for area->pages. It may be too small when __vmalloc_area_node failed early
due to lacking memory. Instead, use a flag in vmstruct to differentiate.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chandra Seetharaman reported SLAB crashes caused by the slab.c lock
annotation patch. There is only one chunk of that patch that has a
material effect on the slab logic - this patch undoes that chunk.
This was confirmed to fix the slab problem by Chandra.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mm/slab.c uses nested locking when dealing with 'off-slab'
caches, in that case it allocates the slab header from the
(on-slab) kmalloc caches. Teach the lock validator about
this by putting all on-slab caches into a separate class.
this patch has no effect on non-lockdep kernels.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
undo existing mm/slab.c lock-validator annotations, in preparation
of a new, less intrusive annotation patch.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch marks three unused exports as EXPORT_UNUSED_SYMBOL.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch marks an unused export as EXPORT_UNUSED_SYMBOL.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch marks an unused export as EXPORT_UNUSED_SYMBOL.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cleanup: remove task_t and convert all the uses to struct task_struct. I
introduced it for the scheduler anno and it was a mistake.
Conversion was mostly scripted, the result was reviewed and all
secondary whitespace and style impact (if any) was fixed up by hand.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Fix initialize-locks-via-memcpy assumptions.
Effects on non-lockdep kernels: the subclass nesting parameter is passed into
cache_free_alien() and __cache_free(), and turns one internal
kmem_cache_free() call into an open-coded __cache_free() call.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Locking init improvement:
- introduce and use __SPIN_LOCK_UNLOCKED for array initializations,
to pass in the name string of locks, used by debugging
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generic lock debugging:
- generalized lock debugging framework. For example, a bug in one lock
subsystem turns off debugging in all lock subsystems.
- got rid of the caller address passing (__IP__/__IP_DECL__/etc.) from
the mutex/rtmutex debugging code: it caused way too much prototype
hackery, and lockdep will give the same information anyway.
- ability to do silent tests
- check lock freeing in vfree too.
- more finegrained debugging options, to allow distributions to
turn off more expensive debugging features.
There's no separate 'held mutexes' list anymore - but there's a 'held locks'
stack within lockdep, which unifies deadlock detection across all lock
classes. (this is independent of the lockdep validation stuff - lockdep first
checks whether we are holding a lock already)
Here are the current debugging options:
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
which do:
config DEBUG_MUTEXES
bool "Mutex debugging, basic checks"
config DEBUG_LOCK_ALLOC
bool "Detect incorrect freeing of live mutexes"
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that it is advantageous to leave a small portion of unmapped file
backed pages if all of a zone's pages (or almost all pages) are allocated and
so the page allocator has to go off-node.
This allows recently used file I/O buffers to stay on the node and
reduces the times that zone reclaim is invoked if file I/O occurs
when we run out of memory in a zone.
The problem is that zone reclaim runs too frequently when the page cache is
used for file I/O (read write and therefore unmapped pages!) alone and we have
almost all pages of the zone allocated. Zone reclaim may remove 32 unmapped
pages. File I/O will use these pages for the next read/write requests and the
unmapped pages increase. After the zone has filled up again zone reclaim will
remove it again after only 32 pages. This cycle is too inefficient and there
are potentially too many zone reclaim cycles.
With the 1% boundary we may still remove all unmapped pages for file I/O in
zone reclaim pass. However. it will take a large number of read and writes
to get back to 1% again where we trigger zone reclaim again.
The zone reclaim 2.6.16/17 does not show this behavior because we have a 30
second timeout.
[akpm@osdl.org: rename the /proc file and the variable]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Post and discussion:
http://marc.theaimsgroup.com/?t=115074342800003&r=1&w=2
Code in __shrink_node() duplicates code in cache_reap()
Add a new function drain_freelist that removes slabs with objects that are
already free and use that in various places.
This eliminates the __node_shrink() function and provides the interrupt
holdoff reduction from slab_free to code that used to call __node_shrink.
[akpm@osdl.org: build fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The numa statistics are really event counters. But they are per node and
so we have had special treatment for these counters through additional
fields on the pcp structure. We can now use the per zone nature of the
zoned VM counters to realize these.
This will shrink the size of the pcp structure on NUMA systems. We will
have some room to add additional per zone counters that will all still fit
in the same cacheline.
Bits Prior pcp size Size after patch We can add
------------------------------------------------------------------
64 128 bytes (16 words) 80 bytes (10 words) 48
32 76 bytes (19 words) 56 bytes (14 words) 8 (64 byte cacheline)
72 (128 byte)
Remove the special statistics for numa and replace them with zoned vm
counters. This has the side effect that global sums of these events now
show up in /proc/vmstat.
Also take the opportunity to move the zone_statistics() function from
page_alloc.c into vmstat.c.
Discussions:
V2 http://marc.theaimsgroup.com/?t=115048227000002&r=1&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No callers.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove writeback state
We can remove some functions now that were needed to calculate the page state
for writeback control since these statistics are now directly available.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_unstable to a per zone counter
We need to do some special modifications to the nfs code since there are
multiple cases of disposition and we need to have a page ref for proper
accounting.
This converts the last critical page state of the VM and therefore we need to
remove several functions that were depending on GET_PAGE_STATE_LAST in order
to make the kernel compile again. We are only left with event type counters
in page state.
[akpm@osdl.org: bugfixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_writeback to per zone counter.
This removes the last page_state counter from arch/i386/mm/pgtable.c so we
drop the page_state from there.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes nr_dirty a per zone counter. Looping over all processors is
avoided during writeback state determination.
The counter aggregation for nr_dirty had to be undone in the NFS layer since
we summed up the page counts from multiple zones. Someone more familiar with
NFS should probably review what I have done.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Allows reclaim to access counter without looping over processor counts.
- Allows accurate statistics on how many pages are used in a zone by
the slab. This may become useful to balance slab allocations over
various zones.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zone_reclaim_interval was necessary because we were not able to determine
how many unmapped pages exist in a zone. Therefore we had to scan in
intervals to figure out if any pages were unmapped.
With the zoned counters and NR_ANON_PAGES we now know the number of pagecache
pages and the number of mapped pages in a zone. So we can simply skip the
reclaim if there is an insufficient number of unmapped pages. We use
SWAP_CLUSTER_MAX as the boundary.
Drop all support for /proc/sys/vm/zone_reclaim_interval.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current NR_FILE_MAPPED is used by zone reclaim and the dirty load
calculation as the number of mapped pagecache pages. However, that is not
true. NR_FILE_MAPPED includes the mapped anonymous pages. This patch
separates those and therefore allows an accurate tracking of the anonymous
pages per zone.
It then becomes possible to determine the number of unmapped pages per zone
and we can avoid scanning for unmapped pages if there are none.
Also it may now be possible to determine the mapped/unmapped ratio in
get_dirty_limit. Isnt the number of anonymous pages irrelevant in that
calculation?
Note that this will change the meaning of the number of mapped pages reported
in /proc/vmstat /proc/meminfo and in the per node statistics. This may affect
user space tools that monitor these counters! NR_FILE_MAPPED works like
NR_FILE_DIRTY. It is only valid for pagecache pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can now access the number of pages in a mapped state in an inexpensive way
in shrink_active_list. So drop the nr_mapped field from scan_control.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a single atomic variable is used to establish the size of the page
cache in the whole machine. The zoned VM counters have the same method of
implementation as the nr_pagecache code but also allow the determination of
the pagecache size per zone.
Remove the special implementation for nr_pagecache and make it a zoned counter
named NR_FILE_PAGES.
Updates of the page cache counters are always performed with interrupts off.
We can therefore use the __ variant here.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nr_mapped is important because it allows a determination of how many pages of
a zone are not mapped, which would allow a more efficient means of determining
when we need to reclaim memory in a zone.
We take the nr_mapped field out of the page state structure and define a new
per zone counter named NR_FILE_MAPPED (the anonymous pages will be split off
from NR_MAPPED in the next patch).
We replace the use of nr_mapped in various kernel locations. This avoids the
looping over all processors in try_to_free_pages(), writeback, reclaim (swap +
zone reclaim).
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per zone counter infrastructure
The counters that we currently have for the VM are split per processor. The
processor however has not much to do with the zone these pages belong to. We
cannot tell f.e. how many ZONE_DMA pages are dirty.
So we are blind to potentially inbalances in the usage of memory in various
zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a
particular node. If we knew then we could put measures into the VM to balance
the use of memory between different zones and different nodes in a NUMA
system. For example it would be possible to limit the dirty pages per node so
that fast local memory is kept available even if a process is dirtying huge
amounts of pages.
Another example is zone reclaim. We do not know how many unmapped pages exist
per zone. So we just have to try to reclaim. If it is not working then we
pause and try again later. It would be better if we knew when it makes sense
to reclaim unmapped pages from a zone. This patchset allows the determination
of the number of unmapped pages per zone. We can remove the zone reclaim
interval with the counters introduced here.
Futhermore the ability to have various usage statistics available will allow
the development of new NUMA balancing algorithms that may be able to improve
the decision making in the scheduler of when to move a process to another node
and hopefully will also enable automatic page migration through a user space
program that can analyse the memory load distribution and then rebalance
memory use in order to increase performance.
The counter framework here implements differential counters for each processor
in struct zone. The differential counters are consolidated when a threshold
is exceeded (like done in the current implementation for nr_pageache), when
slab reaping occurs or when a consolidation function is called.
Consolidation uses atomic operations and accumulates counters per zone in the
zone structure and also globally in the vm_stat array. VM functions can
access the counts by simply indexing a global or zone specific array.
The arrangement of counters in an array also simplifies processing when output
has to be generated for /proc/*.
Counters can be updated by calling inc/dec_zone_page_state or
_inc/dec_zone_page_state analogous to *_page_state. The second group of
functions can be called if it is known that interrupts are disabled.
Special optimized increment and decrement functions are provided. These can
avoid certain checks and use increment or decrement instructions that an
architecture may provide.
We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can
do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is
only currently set for IA64 SGI SN2 and currently only affects
node_page_state(). In the best case node_page_state can be reduced to
retrieving a single counter for the one zone on the node.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: export vm_stat[] for filesystems]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NOTE: ZVC are *not* the lightweight event counters. ZVCs are reliable whereas
event counters do not need to be.
Zone based VM statistics are necessary to be able to determine what the state
of memory in one zone is. In a NUMA system this can be helpful for local
reclaim and other memory optimizations that may be able to shift VM load in
order to get more balanced memory use.
It is also useful to know how the computing load affects the memory
allocations on various zones. This patchset allows the retrieval of that data
from userspace.
The patchset introduces a framework for counters that is a cross between the
existing page_stats --which are simply global counters split per cpu-- and the
approach of deferred incremental updates implemented for nr_pagecache.
Small per cpu 8 bit counters are added to struct zone. If the counter exceeds
certain thresholds then the counters are accumulated in an array of
atomic_long in the zone and in a global array that sums up all zone values.
The small 8 bit counters are next to the per cpu page pointers and so they
will be in high in the cpu cache when pages are allocated and freed.
Access to VM counter information for a zone and for the whole machine is then
possible by simply indexing an array (Thanks to Nick Piggin for pointing out
that approach). The access to the total number of pages of various types does
no longer require the summing up of all per cpu counters.
Benefits of this patchset right now:
- Ability for UP and SMP configuration to determine how memory
is balanced between the DMA, NORMAL and HIGHMEM zones.
- loops over all processors are avoided in writeback and
reclaim paths. We can avoid caching the writeback information
because the needed information is directly accessible.
- Special handling for nr_pagecache removed.
- zone_reclaim_interval vanishes since VM stats can now determine
when it is worth to do local reclaim.
- Fast inline per node page state determination.
- Accurate counters in /sys/devices/system/node/node*/meminfo. Current
counters are counting simply which processor allocated a page somewhere
and guestimate based on that. So the counters were not useful to show
the actual distribution of page use on a specific zone.
- The swap_prefetch patch requires per node statistics in order to
figure out when processors of a node can prefetch. This patch provides
some of the needed numbers.
- Detailed VM counters available in more /proc and /sys status files.
References to earlier discussions:
V1 http://marc.theaimsgroup.com/?l=linux-kernel&m=113511649910826&w=2
V2 http://marc.theaimsgroup.com/?l=linux-kernel&m=114980851924230&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115014697910351&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767318740&w=2
Performance tests with AIM7 did not show any regressions. Seems to be a tad
faster even. Tested on ia64/NUMA. Builds fine on i386, SMP / UP. Includes
fixes for s390/arm/uml arch code.
This patch:
Move counter code from page_alloc.c/page-flags.h to vmstat.c/h.
Create vmstat.c/vmstat.h by separating the counter code and the proc
functions.
Move the vm_stat_text array before zoneinfo_show.
[akpm@osdl.org: s390 build fix]
[akpm@osdl.org: HOTPLUG_CPU build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Memory hotplug code of i386 adds memory to only highmem. So, if
CONFIG_HIGHMEM is not set, CONFIG_MEMORY_HOTPLUG shouldn't be set.
Otherwise, it causes compile error.
In addition, many architecture can't use memory hotplug feature yet. So, I
introduce CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent generic_file_write() deadlock fix caused
generic_file_buffered_write() to loop inifinitely when presented with a
zero-length iovec segment. Fix.
Note that this fix deliberately avoids calling ->prepare_write(),
->commit_write() etc with a zero-length write. This is because I don't trust
all filesystems to get that right.
This is a cautious approach, for 2.6.17.x. For 2.6.18 we should just go ahead
and call ->prepare_write() and ->commit_write() with the zero length and fix
any broken filesystems. So I'll make that change once this code is stabilised
and backported into 2.6.17.x.
The reason for preferring to call ->prepare_write() and ->commit_write() with
the zero-length segment: a zero-length segment _should_ be sufficiently
uncommon that this is the correct way of handling it. We don't want to
optimise for poorly-written userspace at the expense of well-written
userspace.
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Cc: walt <wa1ter@myrealbox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Runtime debugging functionality for rt-mutexes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add debug_check_no_locks_freed(), as a central inline to add
bad-lock-free-debugging functionality to.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_calls associated with cpu_notifier as __cpuinit.
__cpuinit makes sure that the function is init time only unless
CONFIG_HOTPLUG_CPU is defined.
[akpm@osdl.org: section fix]
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generic_file_buffered_write() prefaults in user pages in order to avoid
deadlock on copying from the same page as write goes to.
However, it looks like there is a problem when write is vectored:
fault_in_pages_readable brings in current segment or its part (maxlen).
OTOH, filemap_copy_from_user_iovec is called to copy number of bytes
(bytes) which may exceed current segment, so filemap_copy_from_user_iovec
switches to the next segment which is not brought in yet. Pagefault is
generated. That causes the deadlock if pagefault is for the same page
write goes to: page being written is locked and not uptodate, pagefault
will deadlock trying to lock locked page.
[akpm@osdl.org: somewhat rewritten]
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix "undefined reference to `arch_add_memory'" on sparc64 allmodconfig.
sparc64 doesn't support memory hotplug. But we want it to support
sparsemem.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows hot-add memory which is not aligned to section.
Now, hot-added memory has to be aligned to section size. Considering big
section sized archs, this is not useful.
When hot-added memory is registerd as iomem resoruce by iomem resource
patch, we can make use of that information to detect valid memory range.
Note: With this, not-aligned memory can be registerd. To allow hot-add
memory with holes, we have to do more work around add_memory().
(It doesn't allows add memory to already existing mem section.)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Register hot-added memory to iomem_resource. With this, /proc/iomem can
show hot-added memory.
Note: kdump uses /proc/iomem to catch memory range when it is installed.
So, kdump should be re-installed after /proc/iomem change.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add node-hot-add support to add_memory().
node hotadd uses this sequence.
1. allocate pgdat.
2. refresh NODE_DATA()
3. call free_area_init_node() to initialize
4. create sysfs entry
5. add memory (old add_memory())
6. set node online
7. run kswapd for new node.
(8). update zonelist after pages are onlined. (This is already merged in -mm
due to update phase is difference.)
Note:
To make common function as much as possible,
there is 2 changes from v2.
- The old add_memory(), which is defiend by each archs,
is renamed to arch_add_memory(). New add_memory becomes
caller of arch dependent function as a common code.
- This patch changes add_memory()'s interface
From: add_memory(start, end)
TO : add_memory(nid, start, end).
It was cause of similar code that finding node id from
physical address is inside of old add_memory() on each arch.
In addition, acpi memory hotplug driver can find node id easier.
In v2, it must walk DSDT'S _CRS by matching physical address to
get the handle of its memory device, then get _PXM and node id.
Because input is just physical address.
However, in v3, the acpi driver can use handle to get _PXM and node id
for the new memory device. It can pass just node id to add_memory().
Fix interface of arch_add_memory() is in next patche.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When node is hot-added, kswapd for the node should start. This export kswapd
start function as kswapd_run() to use at add_memory().
[akpm@osdl.org: daemonize() isn't needed when using the kthread API]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the Kconfig entry and actually switch to a 64bit value, if
wanted, for resource_size_t.
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
Every inode in /proc holds a reference to a struct task_struct. If a
directory or file is opened and remains open after the the task exits this
pinning continues. With 8K stacks on a 32bit machine the amount pinned per
file descriptor is about 10K.
Normally I would figure a reasonable per user process limit is about 100
processes. With 80 processes, with a 1000 file descriptors each I can trigger
the 00M killer on a 32bit kernel, because I have pinned about 800MB of useless
data.
This patch replaces the struct task_struct pointer with a pointer to a struct
task_ref which has a struct task_struct pointer. The so the pinning of dead
tasks does not happen.
The code now has to contend with the fact that the task may now exit at any
time. Which is a little but not muh more complicated.
With this change it takes about 1000 processes each opening up 1000 file
descriptors before I can trigger the OOM killer. Much better.
[mlp@google.com: task_mmu small fixes]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Paul Jackson <pj@sgi.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Albert Cahalan <acahalan@gmail.com>
Signed-off-by: Prasanna Meda <mlp@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B).
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (51 commits)
nfs: remove nfs_put_link()
nfs-build-fix-99
git-nfs-build-fixes
Merge branch 'odirect'
NFS: alloc nfs_read/write_data as direct I/O is scheduled
NFS: Eliminate nfs_get_user_pages()
NFS: refactor nfs_direct_free_user_pages
NFS: remove user_addr, user_count, and pos from nfs_direct_req
NFS: "open code" the NFS direct write rescheduler
NFS: Separate functions for counting outstanding NFS direct I/Os
NLM: Fix reclaim races
NLM: sem to mutex conversion
locks.c: add the fl_owner to nlm_compare_locks
NFS: Display the chosen RPCSEC_GSS security flavour in /proc/mounts
NFS: Split fs/nfs/inode.c
NFS: Fix typo in nfs_do_clone_mount()
NFS: Fix compile errors introduced by referrals patches
NFSv4: Ensure that referral mounts bind to a reserved port
NFSv4: A root pathname is sent as a zero component4
NFSv4: Follow a referral
...
Backoff readahead size exponentially on I/O error.
Michael Tokarev <mjt@tls.msk.ru> described the problem as:
[QUOTE]
Suppose there's a CD-rom with a scratch/etc, one sector is unreadable.
In order to "fix" it, one have to read it and write to another CD-rom,
or something.. or just ignore the error (if it's just a skip in a video
stream). Let's assume the unreadable block is number U.
But current behavior is just insane. An application requests block
number N, which is before U. Kernel tries to read-ahead blocks N..U.
Cdrom drive tries to read it, re-read it.. for some time. Finally,
when all the N..U-1 blocks are read, kernel returns block number N
(as requested) to an application, successefully.
Now an app requests block number N+1, and kernel tries to read
blocks N+1..U+1. Retrying again as in previous step.
And so on, up to when an app requests block number U-1. And when,
finally, it requests block U, it receives read error.
So, kernel currentry tries to re-read the same failing block as
many times as the current readahead value (256 (times?) by default).
This whole process already killed my cdrom drive (I posted about it
to LKML several months ago) - literally, the drive has fried, and
does not work anymore. Ofcourse that problem was a bug in firmware
(or whatever) of the drive *too*, but.. main problem with that is
current readahead logic as described above.
[/QUOTE]
Which was confirmed by Jens Axboe <axboe@suse.de>:
[QUOTE]
For ide-cd, it tends do only end the first part of the request on a
medium error. So you may see a lot of repeats :/
[/QUOTE]
With this patch, retries are expected to be reduced from, say, 256, to 5.
[akpm@osdl.org: cleanups]
Signed-off-by: Wu Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put short function description for read_cache_pages() on one line as needed
by kernel-doc.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source address is
not immediately available the copy fails *and* *zeros* *the* *destination*.
This is a problem because a concurrent read (which admittedly is an odd thing
to do) might see zeros rather that was there before the write, or what was
there after, or some mixture of the two (any of these being a reasonable thing
to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't cause an
error.
The first copying does not need to zero any uncopied bytes, and doing so
causes the problem. It uses copy_from_user_atomic rather than copy_from_user
so the simple expedient is to change copy_from_user_atomic to *not* zero out
bytes on failure.
The first of these two patches prepares for the change by fixing two places
which assume copy_from_user_atomic does zero the tail. The two usages are
very similar pieces of code which copy from a userspace iovec into one or more
page-cache pages. These are changed to remove the assumption.
The second patch changes __copy_from_user_inatomic* to not zero the tail.
Once these are accepted, I will look at similar patches of other architectures
where this is important (ppc, mips and sparc being the ones I can find).
This patch:
There is a problem with __copy_from_user_inatomic zeroing the tail of the
buffer in the case of an error. As it is called in atomic context, the error
may be transient, so it results in zeros being written where maybe they
shouldn't be.
In the usage in filemap, this opens a window for a well timed read to see data
(zeros) which is not consistent with any ordering of reads and writes.
Most cases where __copy_from_user_inatomic is called, a failure results in
__copy_from_user being called immediately. As long as the latter zeros the
tail, the former doesn't need to. However in *copy_from_user_iovec
implementations (in both filemap and ntfs/file), it is assumed that
copy_from_user_inatomic will zero the tail.
This patch removes that assumption, so that after this patch it will
be safe for copy_from_user_inatomic to not zero the tail.
This patch also adds some commentary to filemap.h and asm-i386/uaccess.h.
After this patch, all architectures that might disable preempt when
kmap_atomic is called need to have their __copy_from_user_inatomic* "fixed".
This includes
- powerpc
- i386
- mips
- sparc
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is redundant with check in wakeup_kswapd.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pdflush is carefully designed to ensure that all wakeups have some
corresponding work to do - if a woken-up pdflush thread discovers that it
hasn't been given any work to do then this is considered an error.
That all broke when swsusp came along - because a timer-delivered wakeup to a
frozen pdflush thread will just get lost. This causes the pdflush thread to
get lost as well: the writeback timer is supposed to be re-armed by pdflush in
process context, but pdflush doesn't execute the callout which does this.
Fix that up by ignoring the return value from try_to_freeze(): jsut proceed,
see if we have any work pending and only go back to sleep if that is not the
case.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh clarified the role of VM_LOCKED. So we can now implement page
migration for mlocked pages.
Allow the migration of mlocked pages. This means that try_to_unmap must
unmap mlocked pages in the migration case.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hooks for calling vma specific migration functions
With this patch a vma may define a vma->vm_ops->migrate function. That
function may perform page migration on its own (some vmas may not contain page
structs and therefore cannot be handled by regular page migration. Pages in a
vma may require special preparatory treatment before migration is possible
etc) . Only mmap_sem is held when the migration function is called. The
migrate() function gets passed two sets of nodemasks describing the source and
the target of the migration. The flags parameter either contains
MPOL_MF_MOVE which means that only pages used exclusively by
the specified mm should be moved
or
MPOL_MF_MOVE_ALL which means that pages shared with other processes
should also be moved.
The migration function returns 0 on success or an error condition. An error
condition will prevent regular page migration from occurring.
On its own this patch cannot be included since there are no users for this
functionality. But it seems that the uncached allocator will need this
functionality at some point.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AOP_TRUNCATED_PAGE victims in read_pages() belong in the LRU
Nick Piggin rightly pointed out that the introduction of AOP_TRUNCATED_PAGE
to read_pages() was wrong to leave A_T_P victim pages in the page cache but
not put them in the LRU. Failing to do so hid them from the VM.
A_T_P just means that the aop method unlocked the page rather than
performing IO. It would be very rare that the page was truncated between
the unlock and testing A_T_P. So we leave the pages in the LRU for likely
reuse soon rather than backing them back out of the page cache. We do this
by matching the behaviour before the A_T_P introduction which added pages
to the LRU regardless of what ->readpage() did.
This doesn't include the unrelated cleanup in Nick's initial fix which
changed read_pages() to return void to match its only caller's behaviour of
ignoring errors.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.
Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
If invalidate_mapping_pages is called to invalidate a very large mapping
(e.g. a very large block device) and if the only active page in that
device is near the end (or at least, at a very large index), such as, say,
the superblock of an md array, and if that page happens to be locked when
invalidate_mapping_pages is called, then
pagevec_lookup will return this page and
as it is locked, 'next' will be incremented and pagevec_lookup
will be called again. and again. and again.
while we count from 0 upto a very large number.
We should really always set 'next' to 'page->index+1' before going around
the loop again, not just if the page isn't locked.
Cc: "Steinar H. Gunderson" <sgunderson@bigfoot.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add read_mapping_page() which is used for callers that pass
mapping->a_ops->readpage as the filler for read_cache_page. This removes
some duplication from filesystem code.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the x86 cache-bypassing copy instructions for copy_from_user().
Some performance data are
Total of GLOBAL_POWER_EVENTS (CPU cycle samples)
2.6.12.4.orig 1921587
2.6.12.4.nt 1599424
1599424/1921587=83.23% (16.77% reduction)
BSQ_CACHE_REFERENCE (L3 cache miss)
2.6.12.4.orig 57427
2.6.12.4.nt 20858
20858/57427=36.32% (63.7% reduction)
L3 cache miss reduction of __copy_from_user_ll
samples %
37408 65.1412 vmlinux __copy_from_user_ll
23 0.1103 vmlinux __copy_user_zeroing_intel_nocache
23/37408=0.061% (99.94% reduction)
Top 5 of 2.6.12.4.nt
Counted GLOBAL_POWER_EVENTS events (time during which processor is not stopped) with a unit mask of 0x01 (mandatory) count 100000
samples % app name symbol name
128392 8.0274 vmlinux __copy_user_zeroing_intel_nocache
64206 4.0143 vmlinux journal_add_journal_head
59746 3.7355 vmlinux do_get_write_access
47674 2.9807 vmlinux journal_put_journal_head
46021 2.8774 vmlinux journal_dirty_metadata
pattern9-0-cpu4-0-09011728/summary.out
Counted BSQ_CACHE_REFERENCE events (cache references seen by the bus unit) with a unit mask of 0x3f (multiple flags) count 3000
samples % app name symbol name
69755 4.2861 vmlinux __copy_user_zeroing_intel_nocache
55685 3.4215 vmlinux journal_add_journal_head
52371 3.2179 vmlinux __find_get_block
45504 2.7960 vmlinux journal_put_journal_head
36005 2.2123 vmlinux journal_stop
pattern9-0-cpu4-0-09011744/summary.out
Counted BSQ_CACHE_REFERENCE events (cache references seen by the bus unit) with a unit mask of 0x200 (read 3rd level cache miss) count 3000
samples % app name symbol name
1147 5.4994 vmlinux journal_add_journal_head
881 4.2240 vmlinux journal_dirty_data
872 4.1809 vmlinux blk_rq_map_sg
734 3.5192 vmlinux journal_commit_transaction
617 2.9582 vmlinux radix_tree_delete
pattern9-0-cpu4-0-09011731/summary.out
iozone results are
original 2.6.12.4 CPU time = 207.768 sec
cache aware CPU time = 184.783 sec
(three times run)
184.783/207.768=88.94% (11.06% reduction)
original:
pattern9-0-cpu4-0-08191720/iozone.out: CPU Utilization: Wall time 45.997 CPU time 64.527 CPU utilization 140.28 %
pattern9-0-cpu4-0-08191741/iozone.out: CPU Utilization: Wall time 46.878 CPU time 71.933 CPU utilization 153.45 %
pattern9-0-cpu4-0-08191743/iozone.out: CPU Utilization: Wall time 45.152 CPU time 71.308 CPU utilization 157.93 %
cache awre:
pattern9-0-cpu4-0-09011728/iozone.out: CPU Utilization: Wall time 44.842 CPU time 62.465 CPU utilization 139.30 %
pattern9-0-cpu4-0-09011731/iozone.out: CPU Utilization: Wall time 44.718 CPU time 59.273 CPU utilization 132.55 %
pattern9-0-cpu4-0-09011744/iozone.out: CPU Utilization: Wall time 44.367 CPU time 63.045 CPU utilization 142.10 %
Signed-off-by: Hiro Yoshioka <hyoshiok@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch inserts security_task_movememory hook calls into memory management
code to enable security modules to mediate this operation between tasks.
Since the last posting, the hook has been renamed following feedback from
Christoph Lameter.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
move_pages() is used to move individual pages of a process. The function can
be used to determine the location of pages and to move them onto the desired
node. move_pages() returns status information for each page.
long move_pages(pid, number_of_pages_to_move,
addresses_of_pages[],
nodes[] or NULL,
status[],
flags);
The addresses of pages is an array of void * pointing to the
pages to be moved.
The nodes array contains the node numbers that the pages should be moved
to. If a NULL is passed instead of an array then no pages are moved but
the status array is updated. The status request may be used to determine
the page state before issuing another move_pages() to move pages.
The status array will contain the state of all individual page migration
attempts when the function terminates. The status array is only valid if
move_pages() completed successfullly.
Possible page states in status[]:
0..MAX_NUMNODES The page is now on the indicated node.
-ENOENT Page is not present
-EACCES Page is mapped by multiple processes and can only
be moved if MPOL_MF_MOVE_ALL is specified.
-EPERM The page has been mlocked by a process/driver and
cannot be moved.
-EBUSY Page is busy and cannot be moved. Try again later.
-EFAULT Invalid address (no VMA or zero page).
-ENOMEM Unable to allocate memory on target node.
-EIO Unable to write back page. The page must be written
back in order to move it since the page is dirty and the
filesystem does not provide a migration function that
would allow the moving of dirty pages.
-EINVAL A dirty page cannot be moved. The filesystem does not provide
a migration function and has no ability to write back pages.
The flags parameter indicates what types of pages to move:
MPOL_MF_MOVE Move pages that are only mapped by the process.
MPOL_MF_MOVE_ALL Also move pages that are mapped by multiple processes.
Requires sufficient capabilities.
Possible return codes from move_pages()
-ENOENT No pages found that would require moving. All pages
are either already on the target node, not present, had an
invalid address or could not be moved because they were
mapped by multiple processes.
-EINVAL Flags other than MPOL_MF_MOVE(_ALL) specified or an attempt
to migrate pages in a kernel thread.
-EPERM MPOL_MF_MOVE_ALL specified without sufficient priviledges.
or an attempt to move a process belonging to another user.
-EACCES One of the target nodes is not allowed by the current cpuset.
-ENODEV One of the target nodes is not online.
-ESRCH Process does not exist.
-E2BIG Too many pages to move.
-ENOMEM Not enough memory to allocate control array.
-EFAULT Parameters could not be accessed.
A test program for move_pages() may be found with the patches
on ftp.kernel.org:/pub/linux/kernel/people/christoph/pmig/patches-2.6.17-rc4-mm3
From: Christoph Lameter <clameter@sgi.com>
Detailed results for sys_move_pages()
Pass a pointer to an integer to get_new_page() that may be used to
indicate where the completion status of a migration operation should be
placed. This allows sys_move_pags() to report back exactly what happened to
each page.
Wish there would be a better way to do this. Looks a bit hacky.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of passing a list of new pages, pass a function to allocate a new
page. This allows the correct placement of MPOL_INTERLEAVE pages during page
migration. It also further simplifies the callers of migrate pages.
migrate_pages() becomes similar to migrate_pages_to() so drop
migrate_pages_to(). The batching of new page allocations becomes unnecessary.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not leave pages on the lists passed to migrate_pages(). Seems that we will
not need any postprocessing of pages. This will simplify the handling of
pages by the callers of migrate_pages().
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently migrate_pages() is mess with lots of goto. Extract two functions
from migrate_pages() and get rid of the gotos.
Plus we can just unconditionally set the locked bit on the new page since we
are the only one holding a reference. Locking is to stop others from
accessing the page once we establish references to the new page.
Remove the list_del from move_to_lru in order to have finer control over list
processing.
[akpm@osdl.org: add debug check]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes printk() under zone->lock in show_free_areas(). It can be
unsafe to call printk() under this lock, since caller can try to
allocate/free some memory and selfdeadlock on this lock. I found
allocations/freeing mem both in netconsole and serial console.
This issue was faced in reallity when meminfo was periodically printed for
debug purposes and netconsole was used.
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mm/filemap.c:
- add lots of kernel-doc;
- fix some typos and kernel-doc errors;
- drop some blank lines between function close and EXPORT_SYMBOL();
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move comments for kmalloc to right place, currently it near __do_kmalloc
- Comments for kzalloc
- More detailed comments for kmalloc
- Appearance of "kmalloc" and "kzalloc" man pages after "make mandocs"
[rdunlap@xenotime.net: simplification]
Signed-off-by: Paul Drynoff <pauldrynoff@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialise total_memory earlier in boot. Because if for some reason we run
page reclaim early in boot, we don't want total_memory to be zero when we use
it as a divisor.
And rename total_memory to vm_total_pages to avoid naming clashes with
architectures.
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SLAB bootstrap code assumes that the first two kmalloc caches created
(the INDEX_AC and INDEX_L3 kmalloc caches) wont be off-slab. But due to AC
and L3 structure size increase in lockdep, one of them ended up being
off-slab, and subsequently crashing with:
Unable to handle kernel NULL pointer dereference at 0000000000000000 RIP:
[<ffffffff80267478>] kmem_cache_alloc+0x26/0x7d
The fix is to introduce a bootstrap flag and to use it to prevent off-slab
caches being created so early during bootup.
(The calculation for off-slab caches is quite complex so i didnt want to
complicate things with introducing yet another INDEX_ calculation, the flag
approach is simpler and smaller.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two calls to update_mmu_cache in fremap.c, both defective.
The one in install_page needs to be accompanied by lazy_mmu_prot_update
(some other cleanup time, move that into ia64 update_mmu_cache itself); and
the one in install_file_pte should be removed since the pte is not present.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we have atomic_inc_not_zero, it's more elegant for try_to_unuse to
use that on mm_users: doesn't actually matter at present, but safer to be
sure that once mm_users has gone to 0, nothing raises it for an instant.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new VMA operation to notify a filesystem or other driver about the
MMU generating a fault because userspace attempted to write to a page
mapped through a read-only PTE.
This facility permits the filesystem or driver to:
(*) Implement storage allocation/reservation on attempted write, and so to
deal with problems such as ENOSPC more gracefully (perhaps by generating
SIGBUS).
(*) Delay making the page writable until the contents have been written to a
backing cache. This is useful for NFS/AFS when using FS-Cache/CacheFS.
It permits the filesystem to have some guarantee about the state of the
cache.
(*) Account and limit number of dirty pages. This is one piece of the puzzle
needed to make shared writable mapping work safely in FUSE.
Needed by cachefs (Or is it cachefiles? Or fscache? <head spins>).
At least four other groups have stated an interest in it or a desire to use
the functionality it provides: FUSE, OCFS2, NTFS and JFFS2. Also, things like
EXT3 really ought to use it to deal with the case of shared-writable mmap
encountering ENOSPC before we permit the page to be dirtied.
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
get_user_pages(.write=1, .force=1) can generate COW hits on read-only
shared mappings, this patch traps those as mkpage_write candidates and fails
to handle them the old way.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Joel Becker <Joel.Becker@oracle.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Record the node id as we mark sections for instantiation. Use this nid
during instantiation to direct allocations.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Mike Kravetz <kravetz@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Passing an invalid pointer to kfree() and kmem_cache_free() is likely to
cause bad memory corruption or even take down the whole system because the
bad pointer is likely reused immediately due to the per-CPU caches. Until
now, we don't do any verification for this if CONFIG_DEBUG_SLAB is
disabled.
As suggested by Linus, add PageSlab check to page_to_cache() and
page_to_slab() to verify pointers passed to kfree(). Also, move the
stronger check from cache_free_debugcheck() to kmem_cache_free() to ensure
the passed pointer actually belongs to the cache we're about to free the
object.
For page_to_cache() and page_to_slab(), the assertions should have
virtually no extra cost (two instructions, no data cache pressure) and for
kmem_cache_free() the overhead should be minimal.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This implements the use of migration entries to preserve ptes of file backed
pages during migration. Processes can therefore be migrated back and forth
without loosing their connection to pagecache pages.
Note that we implement the migration entries only for linear mappings.
Nonlinear mappings still require the unmapping of the ptes for migration.
And another writepage() ugliness shows up. writepage() can drop the page
lock. Therefore we have to remove migration ptes before calling writepages()
in order to avoid having migration entries point to unlocked pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we install a migration entry then the rss not really decreases since the
page is just moved somewhere else. We can save ourselves the work of
decrementing and later incrementing which will just eventually cause cacheline
bouncing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the migration entries for page migration
This modifies the migration code to use the new migration entries. It now
becomes possible to migrate anonymous pages without having to add a swap
entry.
We add a couple of new functions to replace migration entries with the proper
ptes.
We cannot take the tree_lock for migrating anonymous pages anymore. However,
we know that we hold the only remaining reference to the page when the page
count reaches 1.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rip the page migration logic out.
Remove all code that has to do with swapping during page migration.
This also guts the ability to migrate pages to swap. No one used that so lets
let it go for good.
Page migration should be a bit broken after this patch.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement read/write migration ptes
We take the upper two swapfiles for the two types of migration ptes and define
a series of macros in swapops.h.
The VM is modified to handle the migration entries. migration entries can
only be encountered when the page they are pointing to is locked. This limits
the number of places one has to fix. We also check in copy_pte_range and in
mprotect_pte_range() for migration ptes.
We check for migration ptes in do_swap_cache and call a function that will
then wait on the page lock. This allows us to effectively stop all accesses
to apge.
Migration entries are created by try_to_unmap if called for migration and
removed by local functions in migrate.c
From: Hugh Dickins <hugh@veritas.com>
Several times while testing swapless page migration (I've no NUMA, just
hacking it up to migrate recklessly while running load), I've hit the
BUG_ON(!PageLocked(p)) in migration_entry_to_page.
This comes from an orphaned migration entry, unrelated to the current
correctly locked migration, but hit by remove_anon_migration_ptes as it
checks an address in each vma of the anon_vma list.
Such an orphan may be left behind if an earlier migration raced with fork:
copy_one_pte can duplicate a migration entry from parent to child, after
remove_anon_migration_ptes has checked the child vma, but before it has
removed it from the parent vma. (If the process were later to fault on this
orphaned entry, it would hit the same BUG from migration_entry_wait.)
This could be fixed by locking anon_vma in copy_one_pte, but we'd rather
not. There's no such problem with file pages, because vma_prio_tree_add
adds child vma after parent vma, and the page table locking at each end is
enough to serialize. Follow that example with anon_vma: add new vmas to the
tail instead of the head.
(There's no corresponding problem when inserting migration entries,
because a missed pte will leave the page count and mapcount high, which is
allowed for. And there's no corresponding problem when migrating via swap,
because a leftover swap entry will be correctly faulted. But the swapless
method has no refcounting of its entries.)
From: Ingo Molnar <mingo@elte.hu>
pte_unmap_unlock() takes the pte pointer as an argument.
From: Hugh Dickins <hugh@veritas.com>
Several times while testing swapless page migration, gcc has tried to exec
a pointer instead of a string: smells like COW mappings are not being
properly write-protected on fork.
The protection in copy_one_pte looks very convincing, until at last you
realize that the second arg to make_migration_entry is a boolean "write",
and SWP_MIGRATION_READ is 30.
Anyway, it's better done like in change_pte_range, using
is_write_migration_entry and make_migration_entry_read.
From: Hugh Dickins <hugh@veritas.com>
Remove unnecessary obfuscation from sys_swapon's range check on swap type,
which blew up causing memory corruption once swapless migration made
MAX_SWAPFILES no longer 2 ^ MAX_SWAPFILES_SHIFT.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the fallback code into a new fallback function and make the function
behave like any other migration function. This requires retaking the lock if
pageout() drops it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change handling of address spaces.
Pass a pointer to the address space in which the page is migrated to all
migration function. This avoids repeatedly having to retrieve the address
space pointer from the page and checking it for validity. The old page
mapping will change once migration has gone to a certain step, so it is less
confusing to have the pointer always available.
Move the setting of the mapping and index for the new page into
migrate_pages().
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extract try_to_unmap and rename remove_references -> move_mapping
try_to_unmap() may significantly change the page state by for example setting
the dirty bit. It is therefore best to unmap in migrate_pages() before
calling any migration functions.
migrate_page_remove_references() will then only move the new page in place of
the old page in the mapping. Rename the function to
migrate_page_move_mapping().
This allows us to get rid of the special unmapping for the fallback path.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop nr_refs parameter from migrate_page_remove_references()
The nr_refs parameter is not really useful since the number of remaining
references is always
1 for anonymous pages without a mapping
2 for pages with a mapping
3 for pages with a mapping and PagePrivate set.
Remove the early check for the number of references since we are checking
page_mapcount() earlier. Ultimately only the refcount matters after the
tree_lock has been obtained.
Signed-off-by: Christoph Lameter <clameter@sgi.coim>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the export for migrate_page_remove_references() and migrate_page_copy()
that are unlikely to be used directly by filesystems implementing migration.
The export was useful when buffer_migrate_page() lived in fs/buffer.c but it
has now been moved to migrate.c in the migration reorg.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorder functions in migrate.c. Group all migration functions for struct
address_space_operations together.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
migrate is a better name since it is only used by page migration.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a writeback_control's `start' and `end' fields are used to
indicate a one-byte-range starting at file offset zero, the required
values of .start=0,.end=0 mean that the ->writepages() implementation
has no way of telling that it is being asked to perform a range
request. Because we're currently overloading (start == 0 && end == 0)
to mean "this is not a write-a-range request".
To make all this sane, the patch changes range of writeback_control.
So caller does: If it is calling ->writepages() to write pages, it
sets range (range_start/end or range_cyclic) always.
And if range_cyclic is true, ->writepages() thinks the range is
cyclic, otherwise it just uses range_start and range_end.
This patch does,
- Add LLONG_MAX, LLONG_MIN, ULLONG_MAX to include/linux/kernel.h
-1 is usually ok for range_end (type is long long). But, if someone did,
range_end += val; range_end is "val - 1"
u64val = range_end >> bits; u64val is "~(0ULL)"
or something, they are wrong. So, this adds LLONG_MAX to avoid nasty
things, and uses LLONG_MAX for range_end.
- All callers of ->writepages() sets range_start/end or range_cyclic.
- Fix updates of ->writeback_index. It seems already bit strange.
If it starts at 0 and ended by check of nr_to_write, this last
index may reduce chance to scan end of file. So, this updates
->writeback_index only if range_cyclic is true or whole-file is
scanned.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At present our slab debugging tells us that it detected a double-free or
corruption - it does not distinguish between them. Sometimes it's useful
to be able to differentiate between these two types of information.
Add double-free detection to redzone verification when freeing an object.
As explained by Manfred, when we are freeing an object, both redzones
should be RED_ACTIVE. However, if both are RED_INACTIVE, we are trying to
free an object that was already free'd.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With likely/unlikely profiling on my not-so-busy-typical-developmentsystem
there are 5k misses vs 2k hits. So I guess we should remove the unlikely.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add remap_vmalloc_range, vmalloc_user, and vmalloc_32_user so that drivers
can have a nice interface for remapping vmalloc memory.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rework the swsusp's memory shrinker in the following way:
- Simplify balance_pgdat() by removing all of the swsusp-related code
from it.
- Make shrink_all_memory() use shrink_slab() and a new function
shrink_all_zones() which calls shrink_active_list() and
shrink_inactive_list() directly for each zone in a way that's optimized
for suspend.
In shrink_all_memory() we try to free exactly as many pages as the caller
asks for, preferably in one shot, starting from easier targets. If slab
caches are huge, they are most likely to have enough pages to reclaim.
The inactive lists are next (the zones with more inactive pages go first)
etc.
Each time shrink_all_memory() attempts to shrink the active and inactive
lists for each zone in 5 passes. In the first pass, only the inactive
lists are taken into consideration. In the next two passes the active
lists are also shrunk, but mapped pages are not reclaimed. In the last
two passes the active and inactive lists are shrunk and mapped pages are
reclaimed as well. The aim of this is to alter the reclaim logic to choose
the best pages to keep on resume and improve the responsiveness of the
resumed system.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the _entry variant everywhere to clean the code up a tiny bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last ifdef addition hit the ugliness treshold on this functions, so:
- rename the variable i to nr_pages so it's somewhat descriptive
- remove the addr variable and do the page_address call at the very end
- instead of ifdef'ing the whole alloc_pages_node call just make the
__GFP_COMP addition to flags conditional
- rewrite the __GFP_COMP comment to make sense
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current hugetlb strict accounting for shared mapping always assume mapping
starts at zero file offset and reserves pages between zero and size of the
file. This assumption often reserves (or lock down) a lot more pages then
necessary if application maps at none zero file offset. libhugetlbfs is
one example that requires proper reservation on shared mapping starts at
none zero offset.
This patch extends the reservation and hugetlb strict accounting to support
any arbitrary pair of (offset, len), resulting a much more robust and
accurate scheme. More importantly, it won't lock down any hugetlb pages
outside file mapping.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a few typos in the comments in mm/oom_kill.c.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds panic_on_oom sysctl under sys.vm.
When sysctl vm.panic_on_oom = 1, the kernel panics intead of killing rogue
processes. And if vm.panic_on_oom is 0 the kernel will do oom_kill() in
the same way as it does today. Of course, the default value is 0 and only
root can modifies it.
In general, oom_killer works well and kill rogue processes. So the whole
system can survive. But there are environments where panic is preferable
rather than kill some processes.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have architectures where the size of page_to_pfn and pfn_to_page are
significant enough to overall image size that they wish to push them out of
line. However, in the process we have grown a second copy of the
implementation of each of these routines for each memory model. Share the
implmentation exposing it either inline or out-of-line as required.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In current code, zonelist is considered to be build once, no modification.
But MemoryHotplug can add new zone/pgdat. It must be updated.
This patch modifies build_all_zonelists(). By this, build_all_zonelist() can
reconfig pgdat's zonelists.
To update them safety, this patch use stop_machine_run(). Other cpus don't
touch among updating them by using it.
In old version (V2 of node hotadd), kernel updated them after zone
initialization. But present_page of its new zone is still 0, because
online_page() is not called yet at this time. Build_zonelists() checks
present_pages to find present zone. It was too early. So, I changed it after
online_pages().
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Wait_table is initialized according to zone size at boot time. But, we cannot
know the maixmum zone size when memory hotplug is enabled. It can be
changed.... And resizing of wait_table is hard.
So kernel allocate and initialzie wait_table as its maximum size.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When add_zone() is called against empty zone (not populated zone), we have to
initialize the zone which didn't initialize at boot time. But,
init_currently_empty_zone() may fail due to allocation of wait table. So,
this patch is to catch its error code.
Changes against wait_table is in the next patch.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change definitions of some functions and data from __init to __meminit.
These functions and data can be used after bootup by this patch to be used for
hot-add codes.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is just to rename from wait_table_size() to wait_table_hash_nr_entries().
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove two unnecessary PageSwapCache checks. The page refcount is raised
and therefore page migration cannot occur in both functions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up slab allocator page mapping a bit. The memory allocated for a
slab is physically contiguous so it is okay to assume struct pages are too
so kill the long-standing comment. Furthermore, rename set_slab_attr to
slab_map_pages and add a comment explaining why its needed.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move alien object freeing to cache_free_alien() to reduce #ifdef clutter in
__cache_free().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is better to redo the complete fault if do_swap_page() finds that the
page is not in PageSwapCache() because the page migration code may have
replaced the swap pte already with a pte pointing to valid memory.
do_swap_page() may interpret an invalid swap entry without this patch
because we do not reload the pte if we are looping back. The page
migration code may already have reused the swap entry referenced by our
local swp_entry.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The buddy allocator has a requirement that boundaries between contigious
zones occur aligned with the the MAX_ORDER ranges. Where they do not we
will incorrectly merge pages cross zone boundaries. This can lead to pages
from the wrong zone being handed out.
Originally the buddy allocator would check that buddies were in the same
zone by referencing the zone start and end page frame numbers. This was
removed as it became very expensive and the buddy allocator already made
the assumption that zones boundaries were aligned.
It is clear that not all configurations and architectures are honouring
this alignment requirement. Therefore it seems safest to reintroduce
support for non-aligned zone boundaries. This patch introduces a new check
when considering a page a buddy it compares the zone_table index for the
two pages and refuses to merge the pages where they do not match. The
zone_table index is unique for each node/zone combination when
FLATMEM/DISCONTIGMEM is enabled and for each section/zone combination when
SPARSEMEM is enabled (a SPARSEMEM section is at least a MAX_ORDER size).
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Give the statfs superblock operation a dentry pointer rather than a superblock
pointer.
This complements the get_sb() patch. That reduced the significance of
sb->s_root, allowing NFS to place a fake root there. However, NFS does
require a dentry to use as a target for the statfs operation. This permits
the root in the vfsmount to be used instead.
linux/mount.h has been added where necessary to make allyesconfig build
successfully.
Interest has also been expressed for use with the FUSE and XFS filesystems.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
shmem_rmdir() must undo the increment of i_nlink done in
shmem_get_inode() for directories, otherwise at least
IN_DELETE_SELF inotify event generation is broken.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed a strange behavior in a tmpfs file system the other day, while
building packages - occasionally, and seemingly at random, make decided to
rebuild a target. However, only on tmpfs.
A file would be created, and if checked, it had a sub-second timestamp.
However, after an utimes related call where sub-seconds should be set, they
were zeroed instead. In the case that a file was created, and utimes(...,NULL)
was used on it in the same second, the timestamp on the file moved backwards.
After some digging, I found that this was being caused by tmpfs not having a
time granularity set, thus inheriting the default 1 second granularity.
Hugh adds: yes, we missed tmpfs when the s_time_gran mods went into 2.6.11.
Unfortunately, the granularity of CURRENT_TIME, often used in filesystems,
does not match the default granularity set by alloc_super. A few more such
discrepancies have been found, but this is the most important to fix now.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Christoph Lameter <clameter@sgi.com>
Looks like a comma was left from the conversion from a struct to an
assignment.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all module uses with the new vfs_kern_mount() interface, and fix up
simple_pin_fs().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
mm/slab.c's offlab_limit logic is totally broken.
Firstly, "offslab_limit" is a global variable while it should either be
calculated in situ or should be passed in as a parameter.
Secondly, the more serious problem with it is that the condition for
calculating it:
if (!(OFF_SLAB(sizes->cs_cachep))) {
offslab_limit = sizes->cs_size - sizeof(struct slab);
offslab_limit /= sizeof(kmem_bufctl_t);
is in total disconnect with the condition that makes use of it:
/* More than offslab_limit objects will cause problems */
if ((flags & CFLGS_OFF_SLAB) && num > offslab_limit)
break;
but due to offslab_limit being a global variable this breakage was
hidden.
Up until lockdep came along and perturbed the slab sizes sufficiently so
that the first off-slab cache would still see a (non-calculated) zero
value for offslab_limit and would panic with:
kmem_cache_create: couldn't create cache size-512.
Call Trace:
[<ffffffff8020a5b9>] show_trace+0x96/0x1c8
[<ffffffff8020a8f0>] dump_stack+0x13/0x15
[<ffffffff8022994f>] panic+0x39/0x21a
[<ffffffff80270814>] kmem_cache_create+0x5a0/0x5d0
[<ffffffff80aced62>] kmem_cache_init+0x193/0x379
[<ffffffff80abf779>] start_kernel+0x17f/0x218
[<ffffffff80abf263>] _sinittext+0x263/0x26a
Kernel panic - not syncing: kmem_cache_create(): failed to create slab `size-512'
Paolo Ornati's config on x86_64 managed to trigger it.
The fix is to move the calculation to the place that makes use of it.
This also makes slab.o 54 bytes smaller.
Btw., the check itself is quite silly. Its intention is to test whether
the number of objects per slab would be higher than the number of slab
control pointers possible. In theory it could be triggered: if someone
tried to allocate 4-byte objects cache and explicitly requested with
CFLGS_OFF_SLAB. So i kept the check.
Out of historic interest i checked how old this bug was and it's
ancient, 10 years old! It is the oldest hidden and then truly triggering
bugs i ever saw being fixed in the kernel!
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Yasunori Goto <y-goto@jp.fujitsu.com>
If hot-added memory's address is smaller than old area, spanned_pages will
not be updated. It must be fixed.
example) Old zone_start_pfn = 0x60000, and spanned_pages = 0x10000
Added new memory's start_pfn = 0x50000, and end_pfn = 0x60000
new spanned_pages will be still 0x10000 by old code.
(It should be updated to 0x20000.) Because old_zone_end_pfn will be
0x70000, and end_pfn smaller than it. So, spanned_pages will not be
updated.
In current code, spanned_pages is updated only when end_pfn is updated.
But, it should be updated by subtraction between bigger end_pfn and new
zone_start_pfn.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andy added code to buddy allocator which does not require the zone's
endpoints to be aligned to MAX_ORDER. An issue is that the buddy allocator
requires the node_mem_map's endpoints to be MAX_ORDER aligned. Otherwise
__page_find_buddy could compute a buddy not in node_mem_map for partial
MAX_ORDER regions at zone's endpoints. page_is_buddy will detect that
these pages at endpoints are not PG_buddy (they were zeroed out by bootmem
allocator and not part of zone). Of course the negative here is we could
waste a little memory but the positive is eliminating all the old checks
for zone boundary conditions.
SPARSEMEM won't encounter this issue because of MAX_ORDER size constraint
when SPARSEMEM is configured. ia64 VIRTUAL_MEM_MAP doesn't need the logic
either because the holes and endpoints are handled differently. This
leaves checking alloc_remap and other arches which privately allocate for
node_mem_map.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a couple of infrequently encountered 'sleeping function called from
invalid context' in the cpuset hooks in __alloc_pages. Could sleep while
interrupts disabled.
The routine cpuset_zone_allowed() is called by code in mm/page_alloc.c
__alloc_pages() to determine if a zone is allowed in the current tasks
cpuset. This routine can sleep, for certain GFP_KERNEL allocations, if the
zone is on a memory node not allowed in the current cpuset, but might be
allowed in a parent cpuset.
But we can't sleep in __alloc_pages() if in interrupt, nor if called for a
GFP_ATOMIC request (__GFP_WAIT not set in gfp_flags).
The rule was intended to be:
Don't call cpuset_zone_allowed() if you can't sleep, unless you
pass in the __GFP_HARDWALL flag set in gfp_flag, which disables
the code that might scan up ancestor cpusets and sleep.
This rule was being violated in a couple of places, due to a bogus change
made (by myself, pj) to __alloc_pages() as part of the November 2005 effort
to cleanup its logic, and also due to a later fix to constrain which swap
daemons were awoken.
The bogus change can be seen at:
http://linux.derkeiler.com/Mailing-Lists/Kernel/2005-11/4691.html
[PATCH 01/05] mm fix __alloc_pages cpuset ALLOC_* flags
This was first noticed on a tight memory system, in code that was disabling
interrupts and doing allocation requests with __GFP_WAIT not set, which
resulted in __might_sleep() writing complaints to the log "Debug: sleeping
function called ...", when the code in cpuset_zone_allowed() tried to take
the callback_sem cpuset semaphore.
We haven't seen a system hang on this 'might_sleep' yet, but we are at
decent risk of seeing it fairly soon, especially since the additional
cpuset_zone_allowed() check was added, conditioning wakeup_kswapd(), in
March 2006.
Special thanks to Dave Chinner, for figuring this out, and a tip of the hat
to Nick Piggin who warned me of this back in Nov 2005, before I was ready
to listen.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bad calculation/loop in __section_nr() could result in incorrect section
information being put into sysfs memory entries. This primarily impacts
memory add operations as the sysfs information is used while onlining new
memory.
Fix suggested by Dave Hansen.
Note that the bug may not be obvious from the patch. It actually occurs in
the function's return statement:
return (root_nr * SECTIONS_PER_ROOT) + (ms - root);
In the existing code, root_nr has already been multiplied by
SECTIONS_PER_ROOT.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_NUMA set, kmem_cache_destroy() may fail and say "Can't
free all objects." The problem is caused by sequences such as the
following (suppose we are on a NUMA machine with two nodes, 0 and 1):
* Allocate an object from cache on node 0.
* Free the object on node 1. The object is put into node 1's alien
array_cache for node 0.
* Call kmem_cache_destroy(), which ultimately ends up in __cache_shrink().
* __cache_shrink() does drain_cpu_caches(), which loops through all nodes.
For each node it drains the shared array_cache and then handles the
alien array_cache for the other node.
However this means that node 0's shared array_cache will be drained,
and then node 1 will move the contents of its alien[0] array_cache
into that same shared array_cache. node 0's shared array_cache is
never looked at again, so the objects left there will appear to be in
use when __cache_shrink() calls __node_shrink() for node 0. So
__node_shrink() will return 1 and kmem_cache_destroy() will fail.
This patch fixes this by having drain_cpu_caches() do
drain_alien_cache() on every node before it does drain_array() on the
nodes' shared array_caches.
The problem was originally reported by Or Gerlitz <ogerlitz@voltaire.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
slab_is_available() indicates slab based allocators are available for use.
SPARSEMEM code needs to know this as it can be called at various times
during the boot process.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out in http://bugzilla.kernel.org/show_bug.cgi?id=6490, this
function can experience overflows on 32-bit machines, causing our response to
changed values of min_free_kbytes to go whacky.
Fixing it efficiently is all too hard, so fix it with 64-bit math instead.
Cc: Ake Sandgren <ake.sandgren@hpc2n.umu.se>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on an older patch from Mike Kravetz <kravetz@us.ibm.com>
We need to have a mem_map for high addresses in order to make fops->no_page
work on spufs mem and register files. So far, we have used the
memory_present() function during early bootup, but that did not work when
CONFIG_NUMA was enabled.
We now use the __add_pages() function to add the mem_map when loading the
spufs module, which is a lot nicer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes two bugs with the way sparsemem interacts with memory add.
They are:
- memory leak if memmap for section already exists
- calling alloc_bootmem_node() after boot
These bugs were discovered and a first cut at the fixes were provided by
Arnd Bergmann <arnd@arndb.de> and Joel Schopp <jschopp@us.ibm.com>.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we check PageDirty() in order to make the decision to swap out
the page. However, the dirty information may be only be contained in the
ptes pointing to the page. We need to first unmap the ptes before checking
for PageDirty(). If unmap is successful then the page count of the page
will also be decreased so that pageout() works properly.
This is a fix necessary for 2.6.17. Without this fix we may migrate dirty
pages for filesystems without migration functions. Filesystems may keep
pointers to dirty pages. Migration of dirty pages can result in the
filesystem keeping pointers to freed pages.
Unmapping is currently not be separated out from removing all the
references to a page and moving the mapping. Therefore try_to_unmap will
be called again in migrate_page() if the writeout is successful. However,
it wont do anything since the ptes are already removed.
The coming updates to the page migration code will restructure the code
so that this is no longer necessary.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
transfer_objects should only be called when all of the cpus in the
node are online. CPU_DEAD notifier callback marks l3->shared to NULL.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
find_get_pages_contig() will break out if we hit a hole in the page cache.
From Andrew Morton, small modifications and documentation by me.
Signed-off-by: Jens Axboe <axboe@suse.de>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Basic problem: pages of a shared memory segment can only be migrated once.
In 2.6.16 through 2.6.17-rc1, shared memory mappings do not have a
migratepage address space op. Therefore, migrate_pages() falls back to
default processing. In this path, it will try to pageout() dirty pages.
Once a shared memory page has been migrated it becomes dirty, so
migrate_pages() will try to page it out. However, because the page count
is 3 [cache + current + pte], pageout() will return PAGE_KEEP because
is_page_cache_freeable() returns false. This will abort all subsequent
migrations.
This patch adds a migratepage address space op to shared memory segments to
avoid taking the default path. We use the "migrate_page()" function
because it knows how to migrate dirty pages. This allows shared memory
segment pages to migrate, subject to other conditions such as # pte's
referencing the page [page_mapcount(page)], when requested.
I think this is safe. If we're migrating a shared memory page, then we
found the page via a page table, so it must be in memory.
Can be verified with memtoy and the shmem-mbind-test script, both
available at: http://free.linux.hp.com/~lts/Tools/
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gather_stats() is called with a spinlock held from check_pte_range. We
cannot reschedule with a lock held.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix oom_kill_task() so it doesn't call mmput() (which may sleep) while
holding tasklist_lock.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson <dsp@llnl.gov> points out that badness() is playing with
mm_structs without taking a reference on them.
mmput() can sleep, so taking a reference here (inside tasklist_lock) is
hard. Fix it up via task_lock() instead.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert for-loops that explicitly reference "NR_CPUS" into the
potentially more efficient for_each_possible_cpu() construct.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
madvise_remove needs to respect file and mmap protections.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
[ Will the real CVE-2006-1524 stand up, please.. ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EXPORT_SYMBOL'ing of a static function is not a good idea.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is an enhancement of OVERCOMMIT_GUESS algorithm in
__vm_enough_memory() in mm/nommu.c.
When the OVERCOMMIT_GUESS algorithm calculates the number of free pages,
the algorithm subtracts the number of reserved pages from the result
nr_free_pages().
Signed-off-by: Hideo Aoki <haoki@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is an enhancement of OVERCOMMIT_GUESS algorithm in
__vm_enough_memory() in mm/mmap.c.
When the OVERCOMMIT_GUESS algorithm calculates the number of free pages,
the algorithm subtracts the number of reserved pages from the result
nr_free_pages().
Signed-off-by: Hideo Aoki <haoki@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These patches are an enhancement of OVERCOMMIT_GUESS algorithm in
__vm_enough_memory().
- why the kernel needed patching
When the kernel can't allocate anonymous pages in practice, currnet
OVERCOMMIT_GUESS could return success. This implementation might be
the cause of oom kill in memory pressure situation.
If the Linux runs with page reservation features like
/proc/sys/vm/lowmem_reserve_ratio and without swap region, I think
the oom kill occurs easily.
- the overall design approach in the patch
When the OVERCOMMET_GUESS algorithm calculates number of free pages,
the reserved free pages are regarded as non-free pages.
This change helps to avoid the pitfall that the number of free pages
become less than the number which the kernel tries to keep free.
- testing results
I tested the patches using my test kernel module.
If the patches aren't applied to the kernel, __vm_enough_memory()
returns success in the situation but autual page allocation is
failed.
On the other hand, if the patches are applied to the kernel, memory
allocation failure is avoided since __vm_enough_memory() returns
failure in the situation.
I checked that on i386 SMP 16GB memory machine. I haven't tested on
nommu environment currently.
This patch adds totalreserve_pages for __vm_enough_memory().
Calculate_totalreserve_pages() checks maximum lowmem_reserve pages and
pages_high in each zone. Finally, the function stores the sum of each
zone to totalreserve_pages.
The totalreserve_pages is calculated when the VM is initilized.
And the variable is updated when /proc/sys/vm/lowmem_reserve_raito
or /proc/sys/vm/min_free_kbytes are changed.
Signed-off-by: Hideo Aoki <haoki@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code checks for newbrk with oldbrk which are page aligned before making
a check for the memory limit set of data segment. If the memory limit is
not page aligned in that case it bypasses the test for the limit if the
memory allocation is still for the same page.
Signed-off-by: Ram Gupta <ram.gupta5@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The earlier patch to consolidate mmu and nommu page allocation and
refcounting by using compound pages for nommu allocations had a bug:
kmalloc slabs who's pages were initially allocated by a non-__GFP_COMP
allocator could be passed into mm/nommu.c kmalloc allocations which really
wanted __GFP_COMP underlying pages. Fix that by having nommu pass
__GFP_COMP to all higher order slab allocations.
Signed-off-by: Luke Yang <luke.adi@gmail.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a statistics counter which is incremented everytime the alien cache
overflows. alien_cache limit is hardcoded to 12 right now. We can use
this statistics to tune alien cache if needed in the future.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rohit found an obscure bug causing buddy list corruption.
page_is_buddy is using a non-atomic test (PagePrivate && page_count == 0)
to determine whether or not a free page's buddy is itself free and in the
buddy lists.
Each of the conjuncts may be true at different times due to unrelated
conditions, so the non-atomic page_is_buddy test may find each conjunct to
be true even if they were not both true at the same time (ie. the page was
not on the buddy lists).
Signed-off-by: Martin Bligh <mbligh@google.com>
Signed-off-by: Rohit Seth <rohitseth@google.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The node setup code would try to allocate the node metadata in the node
itself, but that fails if there is no memory in there.
This can happen with memory hotplug when the hotplug area defines an so
far empty node.
Now use bootmem to try to allocate the mem_map in other nodes.
And if it fails don't panic, but just ignore the node.
To make this work I added a new __alloc_bootmem_nopanic function that
does what its name implies.
TBD should try to use nearby nodes here. Currently we just use any.
It's hard to do it better because bootmem doesn't have proper fallback
lists yet.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the comments to match the actual code.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Remove the recently-added LINUX_FADV_ASYNC_WRITE and LINUX_FADV_WRITE_WAIT
fadvise() additions, do it in a new sys_sync_file_range() syscall instead.
Reasons:
- It's more flexible. Things which would require two or three syscalls with
fadvise() can be done in a single syscall.
- Using fadvise() in this manner is something not covered by POSIX.
The patch wires up the syscall for x86.
The sycall is implemented in the new fs/sync.c. The intention is that we can
move sys_fsync(), sys_fdatasync() and perhaps sys_sync() into there later.
Documentation for the syscall is in fs/sync.c.
A test app (sync_file_range.c) is in
http://www.zip.com.au/~akpm/linux/patches/stuff/ext3-tools.tar.gz.
The available-to-GPL-modules do_sync_file_range() is for knfsd: "A COMMIT can
say NFS_DATA_SYNC or NFS_FILE_SYNC. I can skip the ->fsync call for
NFS_DATA_SYNC which is hopefully the more common."
Note: the `async' writeout mode SYNC_FILE_RANGE_WRITE will turn synchronous if
the queue is congested. This is trivial to fix: add a new flag bit, set
wbc->nonblocking. But I'm not sure that we want to expose implementation
details down to that level.
Note: it's notable that we can sync an fd which wasn't opened for writing.
Same with fsync() and fdatasync()).
Note: the code takes some care to handle attempts to sync file contents
outside the 16TB offset on 32-bit machines. It makes such attempts appear to
succeed, for best 32-bit/64-bit compatibility. Perhaps it should make such
requests fail...
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With strict page reservation, I think kernel should enforce number of free
hugetlb page don't fall below reserved count. Currently it is possible in
the sysctl path. Add proper check in sysctl to disallow that.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
git-commit: d5d4b0aa4e
"[PATCH] optimize follow_hugetlb_page" breaks mlock on hugepage areas.
I mis-interpret pages argument and made get_page() unconditional. It
should only get a ref count when "pages" argument is non-null.
Credit goes to Adam Litke who spotted the bug.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
find_trylock_page() is an odd interface in that it doesn't take a reference
like the others. Now that XFS no longer uses it, and its last remaining
caller actually wants an elevated refcount, opencode that callsite and
schedule find_trylock_page() for removal.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Helper functions for for_each_online_pgdat/for_each_zone look too big to be
inlined. Speed of these helper macro itself is not very important. (inner
loops are tend to do more work than this)
This patch make helper function to be out-of-lined.
inline out-of-line
.text 005c0680 005bf6a0
005c0680 - 005bf6a0 = FE0 = 4Kbytes.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
By using for_each_online_pgdat(), pgdat_list is not necessary now. This patch
removes it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a list_head to bootmem_data_t and make bootmems use it. bootmem list is
sorted by node_boot_start.
Only nodes against which init_bootmem() is called are linked to the list.
(i386 allocates bootmem only from one node(0) not from all online nodes.)
A summary:
1. for_each_online_pgdat() traverses all *online* nodes.
2. alloc_bootmem() allocates memory only from initialized-for-bootmem nodes.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes zone_mem_map.
pfn_to_page uses pgdat, page_to_pfn uses zone. page_to_pfn can use pgdat
instead of zone, which is only one user of zone_mem_map. By modifing it,
we can remove zone_mem_map.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are 3 memory models, FLATMEM, DISCONTIGMEM, SPARSEMEM.
Each arch has its own page_to_pfn(), pfn_to_page() for each models.
But most of them can use the same arithmetic.
This patch adds asm-generic/memory_model.h, which includes generic
page_to_pfn(), pfn_to_page() definitions for each memory model.
When CONFIG_OUT_OF_LINE_PFN_TO_PAGE=y, out-of-line functions are
used instead of macro. This is enabled by some archs and reduces
text size.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
drivers/char/ftape/lowlevel/fdc-io.c: Correct a comment
Kconfig help: MTD_JEDECPROBE already supports Intel
Remove ugly debugging stuff
do_mounts.c: Minor ROOT_DEV comment cleanup
BUG_ON() Conversion in drivers/s390/block/dasd_devmap.c
BUG_ON() Conversion in mm/mempool.c
BUG_ON() Conversion in mm/memory.c
BUG_ON() Conversion in kernel/fork.c
BUG_ON() Conversion in ipc/sem.c
BUG_ON() Conversion in fs/ext2/
BUG_ON() Conversion in fs/hfs/
BUG_ON() Conversion in fs/dcache.c
BUG_ON() Conversion in fs/buffer.c
BUG_ON() Conversion in input/serio/hp_sdc_mlc.c
BUG_ON() Conversion in md/dm-table.c
BUG_ON() Conversion in md/dm-path-selector.c
BUG_ON() Conversion in drivers/isdn
BUG_ON() Conversion in drivers/char
BUG_ON() Conversion in drivers/mtd/
Add another allocator to the common mempool code: a kzalloc/kfree allocator
This will be used by the next patch in the series to replace a mempool-backed
kzalloc allocator. It is also very likely that there will be more users in
the future.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add another allocator to the common mempool code: a kmalloc/kfree allocator
This will be used by the next patch in the series to replace duplicate
mempool-backed kmalloc allocators in several places in the kernel. It is also
very likely that there will be more users in the future.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert two mempool users that currently use their own mempool-backed page
allocators to use the generic mempool page allocator.
Also included are 2 trivial whitespace fixes.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will be used by the next patch in the series to replace duplicate
mempool-backed page allocators in 2 places in the kernel. It is also likely
that there will be more users in the future.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, get_user_pages() returns fully coherent pages to the kernel for
anything other than anonymous pages. This is a problem for things like
fuse and the SCSI generic ioctl SG_IO which can potentially wish to do DMA
to anonymous pages passed in by users.
The fix is to add a new memory management API: flush_anon_page() which
is used in get_user_pages() to make anonymous pages coherent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This fixes problems with very large nodes (over 128GB) filling up all of
the first 4GB with their mem_map and not leaving enough space for the
swiotlb.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh is rightly concerned that the CONFIG_DEBUG_VM coverage has gone too
far in vm_normal_page, considering that we expect production kernels to be
shipped with the option turned off, and that the code has been under some
large changes recently.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
The "rounded up to nearest power of 2 in size" algorithm in
alloc_large_system_hash is not correct. As coded, it takes an otherwise
acceptable power-of-2 value and doubles it. For example, we see the error
if we boot with thash_entries=2097152 which produces a hash table with
4194304 entries.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of places are forgetting to take it.
The kswapd case is probably unimportant. keventd_create_kthread() was racy.
The whole thing is a bit flakey: you start a kernel thread, get its pid from
kernel_thread() then look up its task_struct.
a) It assumes that pid recycling takes a "long" time.
b) We get a task_struct but no reference was taken on it. The owner of the
kswapd and kthread task_struct*'s must assume that the new thread won't
exit unexpectedly. Because if it does, they're left holding dead memory
and any attempt to control or stop that task will crash.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In zone_pcp_init we print out all zones even if they are empty:
On node 0 totalpages: 245760
DMA zone: 245760 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
To conserve dmesg space why not print only the non zero zones.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The page migration code could function without NUMA but we currently have
no users for the non-NUMA case.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have had this memory leak for a while now. The situation is complicated
by the use of alloc_kmemlist() as a function to resize various caches by
do_tune_cpucache().
What we do here is first of all make sure that we deallocate properly in
the loop over all the nodes.
If we are just resizing caches then we can simply return with -ENOMEM if an
allocation fails.
If the cache is new then we need to rollback and remove all earlier
allocations.
We detect that a cache is new by checking if the link to the global cache
chain has been setup. This is a bit hackish ....
(also fix up too overlong lines that I added in the last patch...)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Inspired by Jesper Juhl's patch from today
1. Get rid of err
We do not set it to anything else but zero.
2. Drop the CONFIG_NUMA stuff.
There are definitions for alloc_alien_cache and free_alien_cache()
that do the right thing for the non NUMA case.
3. Better naming of variables.
4. Remove redundant cachep->nodelists[node] expressions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__drain_alien_cache() currently drains objects by freeing them to the
(remote) freelists of the original node. However, each node also has a
shared list containing objects to be used on any processor of that node.
We can avoid a number of remote node accesses by copying the pointers to
the free objects directly into the remote shared array.
And while we are at it: Skip alien draining if the alien cache spinlock is
already taken.
Kiran reported that this is a performance benefit.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
slabr_objects() can be used to transfer objects between various object
caches of the slab allocator. It is currently only used during
__cache_alloc() to retrieve elements from the shared array. We will be
using it soon to transfer elements from the alien caches to the remote
shared array.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert mm/ to use the new kmem_cache_zalloc allocator.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Eric Dumazet, optimize kzalloc() calls that pass a
compile-time constant size. Please note that the patch increases kernel
text slightly (~200 bytes for defconfig on x86).
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a memory-zeroing variant of kmem_cache_alloc. The allocator
already exits in XFS and there are potential users for it so this patch
makes the allocator available for the general public.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series creates a strndup_user() function to easy copying C strings
from userspace. Also we avoid common pitfalls like userspace modifying the
final \0 after the strlen_user().
Signed-off-by: Davi Arnaut <davi.arnaut@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to duplicate all that code.
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
msync() does a strange thing. Essentially:
vma = find_vma();
for ( ; ; ) {
if (!vma)
return -ENOMEM;
...
vma = vma->vm_next;
}
so an msync() request which starts within or before a valid VMA and which ends
within or beyond the final VMA will incorrectly return -ENOMEM.
Fix.
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems bad to hold mmap_sem while performing synchronous disk I/O. Alter
the msync(MS_SYNC) code so that the lock is released while we sync the file.
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems sensible to perform dirty page throttling in msync: as the application
dirties pages we can kick off pdflush early, or even force the msync() caller
to perform writeout, or even throttle the msync() caller.
The main effect of this is to start disk writeback earlier if we've just
discovered that a large amount of pagecache has been dirtied. (Otherwise it
wouldn't happen for up to five seconds, next time pdflush wakes up).
It also will cause the page-dirtying process to get panalised for dirtying
those pages rather than whacking someone else with the problem.
We should do this for munmap() and possibly even exit(), too.
We drop the mmap_sem while performing the dirty page balancing. It doesn't
seem right to hold mmap_sem for that long.
Note that this patch only affects MS_ASYNC. MS_SYNC will be syncing all the
dirty pages anyway.
We note that msync(MS_SYNC) does a full-file-sync inside mmap_sem, and always
has. We can fix that up...
The patch also tightens up the mmap_sem coverage in sys_msync(): no point in
taking it while we perform the incoming arg checking.
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need set_page_dirty() to return true if it actually transitioned the page
from a clean to dirty state. This wasn't right in a couple of places. Do a
kernel-wide audit, fix things up.
This leaves open the possibility of returning a negative errno from
set_page_dirty() sometime in the future. But we don't do that at present.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify balance_dirty_pages_ratelimited() so that it can take a
number-of-pages-which-I-just-dirtied argument. For msync().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add two new linux-specific fadvise extensions():
LINUX_FADV_ASYNC_WRITE: start async writeout of any dirty pages between file
offsets `offset' and `offset+len'. Any pages which are currently under
writeout are skipped, whether or not they are dirty.
LINUX_FADV_WRITE_WAIT: wait upon writeout of any dirty pages between file
offsets `offset' and `offset+len'.
By combining these two operations the application may do several things:
LINUX_FADV_ASYNC_WRITE: push some or all of the dirty pages at the disk.
LINUX_FADV_WRITE_WAIT, LINUX_FADV_ASYNC_WRITE: push all of the currently dirty
pages at the disk.
LINUX_FADV_WRITE_WAIT, LINUX_FADV_ASYNC_WRITE, LINUX_FADV_WRITE_WAIT: push all
of the currently dirty pages at the disk, wait until they have been written.
It should be noted that none of these operations write out the file's
metadata. So unless the application is strictly performing overwrites of
already-instantiated disk blocks, there are no guarantees here that the data
will be available after a crash.
To complete this suite of operations I guess we should have a "sync file
metadata only" operation. This gives applications access to all the building
blocks needed for all sorts of sync operations. But sync-metadata doesn't fit
well with the fadvise() interface. Probably it should be a new syscall:
sys_fmetadatasync().
The patch also diddles with the meaning of `endbyte' in sys_fadvise64_64().
It is made to represent that last affected byte in the file (ie: it is
inclusive). Generally, all these byterange and pagerange functions are
inclusive so we can easily represent EOF with -1.
As Ulrich notes, these two functions are somewhat abusive of the fadvise()
concept, which appears to be "set the future policy for this fd".
But these commands are a perfect fit with the fadvise() impementation, and
several of the existing fadvise() commands are synchronous and don't affect
future policy either. I think we can live with the slight incongruity.
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I had trouble understanding working out whether filemap_fdatawrite_range()'s
`end' parameter describes the last-byte-to-be-written or the last-plus-one.
Clarify that in comments.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hook in the slab cache allocation path to handle cpuset memory
spreading for tasks in cpusets with 'memory_spread_slab' enabled has a
modest performance bug. The hook calls into the memory spreading handler
alternate_node_alloc() if either of 'memory_spread_slab' or
'memory_spread_page' is enabled, even though the handler does nothing
(albeit harmlessly) for the page case
Fix - drop PF_SPREAD_PAGE from the set of flag bits that are used to
trigger a call to alternate_node_alloc().
The page case is handled by separate hooks -- see the calls conditioned on
cpuset_do_page_mem_spread() in mm/filemap.c
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hooks in the slab cache allocator code path for support of NUMA
mempolicies and cpuset memory spreading are in an important code path. Many
systems will use neither feature.
This patch optimizes those hooks down to a single check of some bits in the
current tasks task_struct flags. For non NUMA systems, this hook and related
code is already ifdef'd out.
The optimization is done by using another task flag, set if the task is using
a non-default NUMA mempolicy. Taking this flag bit along with the
PF_SPREAD_PAGE and PF_SPREAD_SLAB flag bits added earlier in this 'cpuset
memory spreading' patch set, one can check for the combination of any of these
special case memory placement mechanisms with a single test of the current
tasks task_struct flags.
This patch also tightens up the code, to save a few bytes of kernel text
space, and moves some of it out of line. Due to the nested inlines called
from multiple places, we were ending up with three copies of this code, which
once we get off the main code path (for local node allocation) seems a bit
wasteful of instruction memory.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide the slab cache infrastructure to support cpuset memory spreading.
See the previous patches, cpuset_mem_spread, for an explanation of cpuset
memory spreading.
This patch provides a slab cache SLAB_MEM_SPREAD flag. If set in the
kmem_cache_create() call defining a slab cache, then any task marked with the
process state flag PF_MEMSPREAD will spread memory page allocations for that
cache over all the allowed nodes, instead of preferring the local (faulting)
node.
On systems not configured with CONFIG_NUMA, this results in no change to the
page allocation code path for slab caches.
On systems with cpusets configured in the kernel, but the "memory_spread"
cpuset option not enabled for the current tasks cpuset, this adds a call to a
cpuset routine and failed bit test of the processor state flag PF_SPREAD_SLAB.
For tasks so marked, a second inline test is done for the slab cache flag
SLAB_MEM_SPREAD, and if that is set and if the allocation is not
in_interrupt(), this adds a call to to a cpuset routine that computes which of
the tasks mems_allowed nodes should be preferred for this allocation.
==> This patch adds another hook into the performance critical
code path to allocating objects from the slab cache, in the
____cache_alloc() chunk, below. The next patch optimizes this
hook, reducing the impact of the combined mempolicy plus memory
spreading hooks on this critical code path to a single check
against the tasks task_struct flags word.
This patch provides the generic slab flags and logic needed to apply memory
spreading to a particular slab.
A subsequent patch will mark a few specific slab caches for this placement
policy.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the page cache allocation calls to support cpuset memory spreading.
See the previous patch, cpuset_mem_spread, for an explanation of cpuset memory
spreading.
On systems without cpusets configured in the kernel, this is no change.
On systems with cpusets configured in the kernel, but the "memory_spread"
cpuset option not enabled for the current tasks cpuset, this adds a call to a
cpuset routine and failed bit test of the processor state flag PF_SPREAD_PAGE.
On tasks in cpusets with "memory_spread" enabled, this adds a call to a cpuset
routine that computes which of the tasks mems_allowed nodes should be
preferred for this allocation.
If memory spreading applies to a particular allocation, then any other NUMA
mempolicy does not apply.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we get under some memory pressure in a cpuset (we only scan zones that
are in the cpuset for memory) then kswapd is woken up for all zones. This
patch only wakes up kswapd in zones that are part of the current cpuset.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make that the internal value for /proc/sys/vm/laptop_mode is stored as
jiffies instead of seconds. Let the sysctl interface do the conversions,
instead of doing on-the-fly conversions every time the value is used.
Add a description of the fact that laptop_mode doubles as a flag and a
timeout to the comment above the laptop_mode variable.
Signed-off-by: Bart Samwel <bart@samwel.tk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make that the internal values for:
/proc/sys/vm/dirty_writeback_centisecs
/proc/sys/vm/dirty_expire_centisecs
are stored as jiffies instead of centiseconds. Let the sysctl interface do
the conversions with full precision using clock_t_to_jiffies, instead of
doing overflow-sensitive on-the-fly conversions every time the values are
used.
Cons: apparent precision loss if HZ is not a multiple of 100, because of
conversion back and forth. This is a common problem for all sysctl values
that use proc_dointvec_userhz_jiffies. (There is only one other in-tree
use, in net/core/neighbour.c.)
Signed-off-by: Bart Samwel <bart@samwel.tk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus points out that ext3_readdir's readahead only cuts in when
ext3_readdir() is operating at the very start of the directory. So for large
directories we end up performing no readahead at all and we suck.
So take it all out and use the core VM's page_cache_readahead(). This means
that ext3 directory reads will use all of readahead's dynamic sizing goop.
Note that we're using the directory's filp->f_ra to hold the readahead state,
but readahead is actually being performed against the underlying blockdev's
address_space. Fortunately the readahead code is all set up to handle this.
Tested with printk. It works. I was struggling to find a real workload which
actually cared.
(The patch also exports page_cache_readahead() to GPL modules)
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a user space interface for swsusp.
The interface is based on a special character device, called the snapshot
device, that allows user space processes to perform suspend and resume-related
operations with the help of some ioctls and the read()/write() functions.
Additionally it allows these processes to allocate free swap pages from a
selected swap partition, called the resume partition, so that they know which
sectors of the resume partition are available to them.
The interface uses the same low-level system memory snapshot-handling
functions that are used by the built-it swap-writing/reading code of swsusp.
The interface documentation is included in the patch.
The patch assumes that the major and minor numbers of the snapshot device will
be 10 (ie. misc device) and 231, the registration of which has already been
requested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the low level interface that can be used for handling the
snapshot of the system memory by the in-kernel swap-writing/reading code of
swsusp and the userland interface code (to be introduced shortly).
Also change the way in which swsusp records the allocated swap pages and,
consequently, simplifies the in-kernel swap-writing/reading code (this is
necessary for the userland interface too). To this end, it introduces two
helper functions in mm/swapfile.c, so that the swsusp code does not refer
directly to the swap internals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Centralize the page migration functions in anticipation of additional
tinkering. Creates a new file mm/migrate.c
1. Extract buffer_migrate_page() from fs/buffer.c
2. Extract central migration code from vmscan.c
3. Extract some components from mempolicy.c
4. Export pageout() and remove_from_swap() from vmscan.c
5. Make it possible to configure NUMA systems without page migration
and non-NUMA systems with page migration.
I had to so some #ifdeffing in mempolicy.c that may need a cleanup.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The alien cache rotor in mm/slab.c assumes that the first online node is
node 0. Eventually for some archs, especially with hotplug, this will no
longer be true.
Fix the interleave rotor to handle the general case of node numbering.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bogus node loop in hugetlb.c alloc_fresh_huge_page(), which was
assuming that nodes are numbered contiguously from 0 to num_online_nodes().
Once the hotplug folks get this far, that will be false.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we've allocated SWAPFILE_CLUSTER pages, ->cluster_next should be the
first index of swap cluster. But current code probably sets it wrong offset.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Only disable interrupts if there is actually something to free
2. Only dirty the pcp cacheline if we actually freed something.
3. Disable interrupts for each single pcp and not for cleaning
all the pcps in all zones of a node.
drain_node_pages is called every 2 seconds from cache_reap. This
fix should avoid most disabling of interrupts.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The list_lock also protects the shared array and we call drain_array() with
the shared array. Therefore we cannot go as far as I wanted to but have to
take the lock in a way so that it also protects the array_cache in
drain_pages.
(Note: maybe we should make the array_cache locking more consistent? I.e.
always take the array cache lock for shared arrays and disable interrupts
for the per cpu arrays?)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove drain_array_locked and use that opportunity to limit the time the l3
lock is taken further.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
And a parameter to drain_array to control the freeing of all objects and
then use drain_array() to replace instances of drain_array_locked with
drain_array. Doing so will avoid taking locks in those locations if the
arrays are empty.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cache_reap takes the l3->list_lock (disabling interrupts) unconditionally
and then does a few checks and maybe does some cleanup. This patch makes
cache_reap() only take the lock if there is work to do and then the lock is
taken and released for each cleaning action.
The checking of when to do the next reaping is done without any locking and
becomes racy. Should not matter since reaping can also be skipped if the
slab mutex cannot be acquired.
The same is true for the touched processing. If we get this wrong once in
awhile then we will mistakenly clean or not clean the shared cache. This
will impact performance slightly.
Note that the additional drain_array() function introduced here will fall
out in a subsequent patch since array cleaning will now be very similar
from all callers.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make shrink_all_memory() repeat the attempts to free more memory if there
seems to be no pages to free.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
follow_hugetlb_page() walks a range of user virtual address and then fills
in list of struct page * into an array that is passed from the argument
list. It also gets a reference count via get_page(). For compound page,
get_page() actually traverse back to head page via page_private() macro and
then adds a reference count to the head page. Since we are doing a virt to
pte look up, kernel already has a struct page pointer into the head page.
So instead of traverse into the small unit page struct and then follow a
link back to the head page, optimize that with incrementing the reference
count directly on the head page.
The benefit is that we don't take a cache miss on accessing page struct for
the corresponding user address and more importantly, not to pollute the
cache with a "not very useful" round trip of pointer chasing. This adds a
moderate performance gain on an I/O intensive database transaction
workload.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turns out the hugepage logic in free_pgtables() was doubly broken. The
loop coalescing multiple normal page VMAs into one call to free_pgd_range()
had an off by one error, which could mean it would coalesce one hugepage
VMA into the same bundle (checking 'vma' not 'next' in the loop). I
transferred this bug into the new is_vm_hugetlb_page() based version.
Here's the fix.
This one didn't bite on powerpc previously for the same reason the
is_hugepage_only_range() problem didn't: powerpc's hugetlb_free_pgd_range()
is identical to free_pgd_range(). It didn't bite on ia64 because the
hugepage region is distant enough from any other region that the separated
PMD_SIZE distance test would always prevent coalescing the two together.
No libhugetlbfs testsuite regressions (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
free_pgtables() has special logic to call hugetlb_free_pgd_range() instead
of the normal free_pgd_range() on hugepage VMAs. However, the test it uses
to do so is incorrect: it calls is_hugepage_only_range on a hugepage sized
range at the start of the vma. is_hugepage_only_range() will return true
if the given range has any intersection with a hugepage address region, and
in this case the given region need not be hugepage aligned. So, for
example, this test can return true if called on, say, a 4k VMA immediately
preceding a (nicely aligned) hugepage VMA.
At present we get away with this because the powerpc version of
hugetlb_free_pgd_range() is just a call to free_pgd_range(). On ia64 (the
only other arch with a non-trivial is_hugepage_only_range()) we get away
with it for a different reason; the hugepage area is not contiguous with
the rest of the user address space, and VMAs are not permitted in between,
so the test can't return a false positive there.
Nonetheless this should be fixed. We do that in the patch below by
replacing the is_hugepage_only_range() test with an explicit test of the
VMA using is_vm_hugetlb_page().
This in turn changes behaviour for platforms where is_hugepage_only_range()
returns false always (everything except powerpc and ia64). We address this
by ensuring that hugetlb_free_pgd_range() is defined to be identical to
free_pgd_range() (instead of a no-op) on everything except ia64. Even so,
it will prevent some otherwise possible coalescing of calls down to
free_pgd_range(). Since this only happens for hugepage VMAs, removing this
small optimization seems unlikely to cause any trouble.
This patch causes no regressions on the libhugetlbfs testsuite - ppc64
POWER5 (8-way), ppc64 G5 (2-way) and i386 Pentium M (UP).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Originally, mm/hugetlb.c just handled the hugepage physical allocation path
and its {alloc,free}_huge_page() functions were used from the arch specific
hugepage code. These days those functions are only used with mm/hugetlb.c
itself. Therefore, this patch makes them static and removes their
prototypes from hugetlb.h. This requires a small rearrangement of code in
mm/hugetlb.c to avoid a forward declaration.
This patch causes no regressions on the libhugetlbfs testsuite (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days, hugepages are demand-allocated at first fault time. There's a
somewhat dubious (and racy) heuristic when making a new mmap() to check if
there are enough available hugepages to fully satisfy that mapping.
A particularly obvious case where the heuristic breaks down is where a
process maps its hugepages not as a single chunk, but as a bunch of
individually mmap()ed (or shmat()ed) blocks without touching and
instantiating the pages in between allocations. In this case the size of
each block is compared against the total number of available hugepages.
It's thus easy for the process to become overcommitted, because each block
mapping will succeed, although the total number of hugepages required by
all blocks exceeds the number available. In particular, this defeats such
a program which will detect a mapping failure and adjust its hugepage usage
downward accordingly.
The patch below addresses this problem, by strictly reserving a number of
physical hugepages for hugepage inodes which have been mapped, but not
instatiated. MAP_SHARED mappings are thus "safe" - they will fail on
mmap(), not later with an OOM SIGKILL. MAP_PRIVATE mappings can still
trigger an OOM. (Actually SHARED mappings can technically still OOM, but
only if the sysadmin explicitly reduces the hugepage pool between mapping
and instantiation)
This patch appears to address the problem at hand - it allows DB2 to start
correctly, for instance, which previously suffered the failure described
above.
This patch causes no regressions on the libhugetblfs testsuite, and makes a
test (designed to catch this problem) pass which previously failed (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, no lock or mutex is held between allocating a hugepage and
inserting it into the pagetables / page cache. When we do go to insert the
page into pagetables or page cache, we recheck and may free the newly
allocated hugepage. However, since the number of hugepages in the system
is strictly limited, and it's usualy to want to use all of them, this can
still lead to spurious allocation failures.
For example, suppose two processes are both mapping (MAP_SHARED) the same
hugepage file, large enough to consume the entire available hugepage pool.
If they race instantiating the last page in the mapping, they will both
attempt to allocate the last available hugepage. One will fail, of course,
returning OOM from the fault and thus causing the process to be killed,
despite the fact that the entire mapping can, in fact, be instantiated.
The patch fixes this race by the simple method of adding a (sleeping) mutex
to serialize the hugepage fault path between allocation and insertion into
pagetables and/or page cache. It would be possible to avoid the
serialization by catching the allocation failures, waiting on some
condition, then rechecking to see if someone else has instantiated the page
for us. Given the likely frequency of hugepage instantiations, it seems
very doubtful it's worth the extra complexity.
This patch causes no regression on the libhugetlbfs testsuite, and one
test, which can trigger this race now passes where it previously failed.
Actually, the test still sometimes fails, though less often and only as a
shmat() failure, rather processes getting OOM killed by the VM. The dodgy
heuristic tests in fs/hugetlbfs/inode.c for whether there's enough hugepage
space aren't protected by the new mutex, and would be ugly to do so, so
there's still a race there. Another patch to replace those tests with
something saner for this reason as well as others coming...
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the loops used in mm/hugetlb.c to clear and copy hugepages to their
own functions for clarity. As we do so, we add some checks of need_resched
- we are, after all copying megabytes of memory here. We also add
might_sleep() accordingly. We generally dropped locks around the clear and
copy, already but not everyone has PREEMPT enabled, so we should still be
checking explicitly.
For this to work, we need to remove the clear_huge_page() from
alloc_huge_page(), which is called with the page_table_lock held in the COW
path. We move the clear_huge_page() to just after the alloc_huge_page() in
the hugepage no-page path. In the COW path, the new page is about to be
copied over, so clearing it was just a waste of time anyway. So as a side
effect we also fix the fact that we held the page_table_lock for far too
long in this path by calling alloc_huge_page() under it.
It causes no regressions on the libhugetlbfs testsuite (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.16-rc3 uses hugetlb on-demand paging, but it doesn_t support hugetlb
mprotect.
From: David Gibson <david@gibson.dropbear.id.au>
Remove a test from the mprotect() path which checks that the mprotect()ed
range on a hugepage VMA is hugepage aligned (yes, really, the sense of
is_aligned_hugepage_range() is the opposite of what you'd guess :-/).
In fact, we don't need this test. If the given addresses match the
beginning/end of a hugepage VMA they must already be suitably aligned. If
they don't, then mprotect_fixup() will attempt to split the VMA. The very
first test in split_vma() will check for a badly aligned address on a
hugepage VMA and return -EINVAL if necessary.
From: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
On i386 and x86-64, pte flag _PAGE_PSE collides with _PAGE_PROTNONE. The
identify of hugetlb pte is lost when changing page protection via mprotect.
A page fault occurs later will trigger a bug check in huge_pte_alloc().
The fix is to always make new pte a hugetlb pte and also to clean up
legacy code where _PAGE_PRESENT is forced on in the pre-faulting day.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current current get_init_ra_size is not optimal across different IO
sizes and max_readahead values. Here is a quick summary of sizes computed
under current design and under the attached patch. All of these assume 1st
IO at offset 0, or 1st detected sequential IO.
32k max, 4k request
old new
-----------------
8k 8k
16k 16k
32k 32k
128k max, 4k request
old new
-----------------
32k 16k
64k 32k
128k 64k
128k 128k
128k max, 32k request
old new
-----------------
32k 64k <-----
64k 128k
128k 128k
512k max, 4k request
old new
-----------------
4k 32k <----
16k 64k
64k 128k
128k 256k
512k 512k
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Steven Pratt <slpratt@austin.ibm.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If get_next_ra_size() does not grow fast enough, ->prev_page can overrun
the ahead window. This means the caller will read the pages from
->ahead_start + ->ahead_size to ->prev_page synchronously.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Steven Pratt <slpratt@austin.ibm.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
shmem.c was named and shamed in Jesper's "Building 100 kernels" warnings:
shmem_parse_mpol is only used when CONFIG_TMPFS parses mount options; and
only called from that one site, so mark it inline like its non-NUMA stub.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Marcelo:
1. The optimization introduced recently for not calling
page_referenced() during zone reclaim makes two additional checks in
shrink_list unnecessary.
2. The if (unlikely(sc->may_swap)) in refill_inactive_zone is optimized
for the zone_reclaim case. However, most peoples system only does swap.
Undo that.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put a few more checks under CONFIG_DEBUG_VM
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
prep_zero_page() uses KM_USER0 and hence may not be used from IRQ context, at
least for highmem pages.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the prep_ stuff into prep_new_page.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that compound page handling is properly fixed in the VM, move nommu
over to using compound pages rather than rolling their own refcounting.
nommu vm page refcounting is broken anyway, but there is no need to have
divergent code in the core VM now, nor when it gets fixed.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: David Howells <dhowells@redhat.com>
(Needs testing, please).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove __put_page from outside the core mm/. It is dangerous because it does
not handle compound pages nicely, and misses 1->0 transitions. If a user
later appears that really needs the extra speed we can reevaluate.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that it's madvisable, remove two pieces of VM_DONTCOPY bogosity:
1. There was and is no logical reason why VM_DONTCOPY should be in the
list of flags which forbid vma merging (and those drivers which set
it are also setting VM_IO, which itself forbids the merge).
2. It's hard to understand the purpose of the VM_HUGETLB, VM_DONTCOPY
block in vm_stat_account: but never mind, it's under CONFIG_HUGETLB,
which (unlike CONFIG_HUGETLB_PAGE or CONFIG_HUGETLBFS) has never been
defined.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In shrink_inactive_list(), nr_scan is not accounted when nr_taken is 0.
But 0 pages taken does not mean 0 pages scanned.
Move the goto statement below the accounting code to fix it.
Signed-off-by: Wu Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In isolate_lru_pages(), *scanned reports one more scan because the scan
counter is increased one more time on exit of the while-loop.
Change the while-loop to for-loop to fix it.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Wu Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some comments to explain how zone reclaim works. And it fixes the
following issues:
- PF_SWAPWRITE needs to be set for RECLAIM_SWAP to be able to write
out pages to swap. Currently RECLAIM_SWAP may not do that.
- remove setting nr_reclaimed pages after slab reclaim since the slab shrinking
code does not use that and the nr_reclaimed pages is just right for the
intended follow up action.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have:
try_to_free_pages
->shrink_caches(struct zone **zones, ..)
->shrink_zone(struct zone *, ...)
->shrink_cache(struct zone *, ...)
->shrink_list(struct list_head *, ...)
->refill_inactive_list((struct zone *, ...)
which is fairly irrational.
Rename things so that we have
try_to_free_pages
->shrink_zones(struct zone **zones, ..)
->shrink_zone(struct zone *, ...)
->shrink_inactive_list(struct zone *, ...)
->shrink_page_list(struct list_head *, ...)
->shrink_active_list(struct zone *, ...)
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the vmscan functions to retunr the number-of-reclaimed pages and
remove scan_conrtol.nr_reclaimed.
Saves ten-odd bytes of text and makes things clearer and more consistent.
The patch also changes the behaviour of zone_reclaim() when it falls back to slab shrinking. Christoph says
"Setting this to one means that we will rescan and shrink the slab for
each allocation if we are out of zone memory and RECLAIM_SLAB is set. Plus
if we do an order 0 allocation we do not go off node as intended.
"We better set this to zero. This means the allocation will go offnode
despite us having potentially freed lots of memory on the zone. Future
allocations can then again be done from this zone."
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turn basically everything in vmscan.c into `unsigned long'. This is to avoid
the possibility that some piece of code in there might decide to operate upon
more than 4G (or even 2G) of pages in one hit.
This might be silly, but we'll need it one day.
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialise as much of scan_control as possible at the declaration site. This
tidies things up a bit and assures us that all unmentioned fields are zeroed
out.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make nr_to_scan and priority a parameter instead of putting it into scan
control. This allows various small optimizations and IMHO makes the code
easier to read.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have struct kmem_cache now so use it instead of the old typedef.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove cachep->spinlock. Locking has moved to the kmem_list3 and most of
the structures protected earlier by cachep->spinlock is now protected by
the l3->list_lock. slab cache tunables like batchcount are accessed always
with the cache_chain_mutex held.
Patch tested on SMP and NUMA kernels with dbench processes running,
constant onlining/offlining, and constant cache tuning, all at the same
time.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Christoph Lameter <christoph@lameter.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
slab.c has become a bit revolting again. Try to repair it.
- Coding style fixes
- Don't do assignments-in-if-statements.
- Don't typecast assignments to/from void*
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extract setup_cpu_cache() function from kmem_cache_create() to make the
latter a little less complex.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the object to index mapping that has been spread around mm/slab.c.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Insert "fresh" huge pages into the hugepage allocator by the same means as
they are freed back into it. This reduces code size and allows
enqueue_huge_page to be inlined into the hugepage free fastpath.
Eliminate occurances of hugepages on the free list with non-zero refcount.
This can allow stricter refcount checks in future. Also required for
lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
"This patch also eliminates a leak "cleaned up" by re-clobbering the
refcount on every allocation from the hugepage freelists. With respect to
the lockless pagecache, the crucial aspect is to eliminate unconditional
set_page_count() to 0 on pages with potentially nonzero refcounts, though
closer inspection suggests the assignments removed are entirely spurious."
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The bootmem code added to page_alloc.c duplicated some page freeing code
that it really doesn't need to because it is not so performance critical.
While we're here, make prefetching work properly by actually prefetching
the page we're about to use before prefetching ahead to the next one (ie.
get the most important transaction started first). Also prefetch just a
single page ahead rather than leaving a gap of 16.
Jack Steiner reported no problems with SGI's ia64 simulator.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have an explicit mm call to split higher order pages into individual pages.
Should help to avoid bugs and be more explicit about the code's intention.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VM has an interesting race where a page refcount can drop to zero, but it
is still on the LRU lists for a short time. This was solved by testing a 0->1
refcount transition when picking up pages from the LRU, and dropping the
refcount in that case.
Instead, use atomic_add_unless to ensure we never pick up a 0 refcount page
from the LRU, thus a 0 refcount page will never have its refcount elevated
until it is allocated again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
More atomic operation removal from page allocator
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the page release paths, we can be sure that nobody will mess with our
page->flags because the refcount has dropped to 0. So no need for atomic
operations here.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PG_active is protected by zone->lru_lock, it does not need TestSet/TestClear
operations.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PG_lru is protected by zone->lru_lock. It does not need TestSet/TestClear
operations.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If vmscan finds a zero refcount page on the lru list, never ClearPageLRU
it. This means the release code need not hold ->lru_lock to stabilise
PageLRU, so that lock may be skipped entirely when releasing !PageLRU pages
(because we know PageLRU won't have been temporarily cleared by vmscan,
which was previously guaranteed by holding the lock to synchronise against
vmscan).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__get_page_state() has an open-coded for_each_cpu_mask() loop in it.
Tidy that up, then notice that the code was buggy:
while (cpu < NR_CPUS) {
unsigned long *in, *out, off;
if (!cpu_isset(cpu, *cpumask))
continue;
an obvious infinite loop. I guess we just never call it with a holey cpu
mask.
Even after my cpumask size-reduction work, this patch increases code size :(
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lee Revell reported 28ms latency when process with lots of swapped memory
exits.
2.6.15 introduced a latency regression when unmapping: in accounting the
zap_work latency breaker, pte_none counted 1, pte_present PAGE_SIZE, but a
swap entry counted nothing at all. We think of pages present as the slow
case, but Lee's trace shows that free_swap_and_cache's radix tree lookup
can make a lot of work - and we could have been doing it many thousands of
times without a latency break.
Move the zap_work update up to account swap entries like pages present.
This does account non-linear pte_file entries, and unmap_mapping_range
skipping over swap entries, by the same amount even though they're quick:
but neither of those cases deserves complicating the code (and they're
treated no worse than they were in 2.6.14).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can call try_to_release_page() with PagePrivate off and a valid
page->mapping This may cause all sorts of trouble for the filesystem
*_releasepage() handlers. XFS bombs out in that case.
Lock the page before checking for page private.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the migration of anonymous pages will silently fail if no swap is
setup. This patch makes page migration functions check for available swap
and fail with -ENODEV if no swap space is available.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that setting scheduling policy and priorities is also the kind of
thing that might be performed in apps that also use the NUMA API, so it
would seem consistent to use CAP_SYS_NICE for NUMA also.
So use CAP_SYS_NICE for controlling migration permissions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
page migration currently simply retries a couple of times if try_to_unmap()
fails without inspecting the return code.
However, SWAP_FAIL indicates that the page is in a vma that has the
VM_LOCKED flag set (if ignore_refs ==1). We can check for that return code
and avoid retrying the migration.
migrate_page_remove_references() now needs to return a reason why the
failure occured. So switch migrate_page_remove_references to use -Exx
style error messages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The cache reaper currently tries to free all alien caches and all remote
per cpu pages in each pass of cache_reap. For a machines with large number
of nodes (such as Altix) this may lead to sporadic delays of around ~10ms.
Interrupts are disabled while reclaiming creating unacceptable delays.
This patch changes that behavior by adding a per cpu reap_node variable.
Instead of attempting to free all caches, we free only one alien cache and
the per cpu pages from one remote node. That reduces the time spend in
cache_reap. However, doing so will lengthen the time it takes to
completely drain all remote per cpu pagesets and all alien caches. The
time needed will grow with the number of nodes in the system. All caches
are drained when they overflow their respective capacity. So the drawback
here is only that a bit of memory may be wasted for awhile longer.
Details:
1. Rename drain_remote_pages to drain_node_pages to allow the specification
of the node to drain of pcp pages.
2. Add additional functions init_reap_node, next_reap_node for NUMA
that manage a per cpu reap_node counter.
3. Add a reap_alien function that reaps only from the current reap_node.
For us this seems to be a critical issue. Holdoffs of an average of ~7ms
cause some HPC benchmarks to slow down significantly. F.e. NAS parallel
slows down dramatically. NAS parallel has a 12-16 seconds runtime w/o rotor
compared to 5.8 secs with the rotor patches. It gets down to 5.05 secs with
the additional interrupt holdoff reductions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When pages are onlined, not only zone->present_pages but also
pgdat->node_present_pages should be refreshed.
This parameter is used to show information at
/sys/device/system/node/nodeX/meminfo via si_meminfo_node().
So, it shows strange value for MemUsed which is calculated
(node_present_pages - all zones free pages).
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the process has already set PF_MALLOC and is already using
current->reclaim_state then do not try to reclaim memory from the zone.
This is set by kswapd and/or synchrononous global reclaim which will not
take it lightly if we zap the reclaim_state.
Signed-off-by: Christoph Lameter <clameter@sig.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove two early-development BUG_ONs from page_add_file_rmap.
The pfn_valid test (originally useful for checking that nobody passed an
artificial struct page) comes too late, since we already have the struct
page.
The PageAnon test (useful when anon was first distinguished from file rmap)
prevents ->nopage implementations from reusing ->mapping, which would
otherwise be available.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kmem_cache_init() incorrectly assumes that the cache_cache object will fit
in an order 0 allocation. On very large systems, this is not true. Change
the code to try larger order allocations if order 0 fails.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement percpu_counter_sum(). This is a more accurate but slower version of
percpu_counter_read_positive().
We need this for Alex's speedup-ext3_statfs patch and for the nr_file
accounting fix. Otherwise these things would be too inaccurate on large CPU
counts.
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the mm/mempolicy.c build for !CONFIG_HUGETLB_PAGE.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of having a hard-to-read and confusing conditional in the
caller, just make the slab order calculation handle this special case,
since it's simple and obvious there.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the format of numa_maps to be more compact and contain additional
information that is useful for managing and troubleshooting memory on a
NUMA system. Numa_maps can now also support huge pages.
Fixes:
1. More compact format. Only display fields if they contain additional
information.
2. Always display information for all vmas. The old numa_maps did not display
vma with no mapped entries. This was a bit confusing because page
migration removes ptes for file backed vmas. After page migration
a part of the vmas vanished.
3. Rename maxref to maxmap. This is the maximum mapcount of all the pages
in a vma and may be used as an indicator as to how many processes
may be using a certain vma.
4. Include the ability to scan over huge page vmas.
New items shown:
dirty
Number of pages in a vma that have either the dirty bit set in the
page_struct or in the pte.
file=<filename>
The file backing the pages if any
stack
Stack area
heap
Heap area
huge
Huge page area. The number of pages shows is the number of huge
pages not the regular sized pages.
swapcache
Number of pages with swap references. Must be >0 in order to
be shown.
active
Number of active pages. Only displayed if different from the number
of pages mapped.
writeback
Number of pages under writeback. Only displayed if >0.
Sample ouput of a process using huge pages:
00000000 default
2000000000000000 default file=/lib/ld-2.3.90.so mapped=13 mapmax=30 N0=13
2000000000044000 default file=/lib/ld-2.3.90.so anon=2 dirty=2 swapcache=2 N2=2
2000000000064000 default file=/lib/librt-2.3.90.so mapped=2 active=1 N1=1 N3=1
2000000000074000 default file=/lib/librt-2.3.90.so
2000000000080000 default file=/lib/librt-2.3.90.so anon=1 swapcache=1 N2=1
2000000000084000 default
2000000000088000 default file=/lib/libc-2.3.90.so mapped=52 mapmax=32 active=48 N0=52
20000000002bc000 default file=/lib/libc-2.3.90.so
20000000002c8000 default file=/lib/libc-2.3.90.so anon=3 dirty=2 swapcache=3 active=2 N1=1 N2=2
20000000002d4000 default anon=1 swapcache=1 N1=1
20000000002d8000 default file=/lib/libpthread-2.3.90.so mapped=8 mapmax=3 active=7 N2=2 N3=6
20000000002fc000 default file=/lib/libpthread-2.3.90.so
2000000000308000 default file=/lib/libpthread-2.3.90.so anon=1 dirty=1 swapcache=1 N1=1
200000000030c000 default anon=1 dirty=1 swapcache=1 N1=1
2000000000320000 default anon=1 dirty=1 N1=1
200000000071c000 default
2000000000720000 default anon=2 dirty=2 swapcache=1 N1=1 N2=1
2000000000f1c000 default
2000000000f20000 default anon=2 dirty=2 swapcache=1 active=1 N2=1 N3=1
200000000171c000 default
2000000001720000 default anon=1 dirty=1 swapcache=1 N1=1
2000000001b20000 default
2000000001b38000 default file=/lib/libgcc_s.so.1 mapped=2 N1=2
2000000001b48000 default file=/lib/libgcc_s.so.1
2000000001b54000 default file=/lib/libgcc_s.so.1 anon=1 dirty=1 active=0 N1=1
2000000001b58000 default file=/lib/libunwind.so.7.0.0 mapped=2 active=1 N1=2
2000000001b74000 default file=/lib/libunwind.so.7.0.0
2000000001b80000 default file=/lib/libunwind.so.7.0.0
2000000001b84000 default
4000000000000000 default file=/media/huge/test9 mapped=1 N1=1
6000000000000000 default file=/media/huge/test9 anon=1 dirty=1 active=0 N1=1
6000000000004000 default heap
607fffff7fffc000 default anon=1 dirty=1 swapcache=1 N2=1
607fffffff06c000 default stack anon=1 dirty=1 active=0 N1=1
8000000060000000 default file=/mnt/huge/test0 huge dirty=3 N1=3
8000000090000000 default file=/mnt/huge/test1 huge dirty=3 N0=1 N2=2
80000000c0000000 default file=/mnt/huge/test2 huge dirty=3 N1=1 N3=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we triggered the 'offslab_limit' test, we would return with
cachep->gfporder incremented once too many times.
This clarifies the logic somewhat, and fixes that bug.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We want to use the "struct slab" size, not the size of the pointer to
same. As it is, we'd not print out the last <n> entry pointers in the
slab (where <n> is ~10, depending on whether it's a 32-bit or 64-bit
kernel).
Gaah, that slab code was written by somebody who likes unreadable crud.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
