This allows the LPE HDMI driver to clean up its global variable
reference.
Also drop to pass the eld pointer because the connection status and
the ELD bytes can be retrieved from the attached pdata.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the pipe that is being used is passed over i915 notification, we
can re-setup the relevant register offset depending on pipe assignments
during hotplug.
This allows playback on single port machines such Zotac Pi330 or
dual-port machines such as Dell Wyse 3040 box
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Imported from legacy patches
Note: the new code doesn't assume a modified ELD but
an explicit notification that DP is present. It appears
that the i915 code does change the ELD so we could use
the ELD-based tests to check for DP audio
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LPE audio configuration depends on the pipe, thus we need to pass
the currently used pipe. It's now embedded in struct
intel_hdmi_lpe_audio_eld as well as port id.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pipe gets cleared to -1 for non-MST before the ELD audio
notification due to the MST audio support. This makes sense for
HD-audio that received the MST handling, but it's useless for LPE
audio. Handle the MST pipe hack conditionally only for HD-audio.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable unmute/mute amp notification. This doesn't seem to affect
HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38
prior to the mute/unmute but this register doesn't seem to do anything
so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If DisplayPort is detected, pass flag and link rate to audio driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Atomic drivers may set properties like rotation on the same fb, which
may require a call to prepare_fb even when framebuffer stays identical.
Instead of handling all the special cases in the core, let the driver
decide when prepare_fb and cleanup_fb are noops.
This is a revert of:
commit fcc60b413d
Author: Keith Packard <keithp@keithp.com>
Date: Sat Jun 4 01:16:22 2016 -0700
drm: Don't prepare or cleanup unchanging frame buffers [v3]
The original commit mentions that this prevents waiting in i915 on all
previous rendering during cursor updates, but there are better ways to
fix this.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6d82f9b6-9d16-91d1-d176-4a37b09afc44@linux.intel.com
(cherry picked from commit 0532be078a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485854491-27389-2-git-send-email-maarten.lankhorst@linux.intel.com
The package management code in uncore relies on package mapping being
available before a CPU is started. This changed with:
9d85eb9119 ("x86/smpboot: Make logical package management more robust")
because the ACPI/BIOS information turned out to be unreliable, but that
left uncore in broken state. This was not noticed because on a regular boot
all CPUs are online before uncore is initialized.
Move the allocation to the CPU online callback and simplify the hotplug
handling. At this point the package mapping is established and correct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Yasuaki Ishimatsu <yasu.isimatu@gmail.com>
Fixes: 9d85eb9119 ("x86/smpboot: Make logical package management more robust")
Link: http://lkml.kernel.org/r/20170131230141.377156255@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The recent conversion to the hotplug state machine kept two mechanisms from
the original code:
1) The first_init logic which adds the number of online CPUs in a package
to the refcount. That's wrong because the callbacks are executed for
all online CPUs.
Remove it so the refcounting is correct.
2) The on_each_cpu() call to undo box->init() in the error handling
path. That's bogus because when the prepare callback fails no box has
been initialized yet.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Yasuaki Ishimatsu <yasu.isimatu@gmail.com>
Fixes: 1a246b9f58 ("perf/x86/intel/uncore: Convert to hotplug state machine")
Link: http://lkml.kernel.org/r/20170131230141.298032324@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The package management code in RAPL relies on package mapping being
available before a CPU is started. This changed with:
9d85eb9119 ("x86/smpboot: Make logical package management more robust")
because the ACPI/BIOS information turned out to be unreliable, but that
left RAPL in broken state. This was not noticed because on a regular boot
all CPUs are online before RAPL is initialized.
A possible fix would be to reintroduce the mess which allocates a package
data structure in CPU prepare and when it turns out to already exist in
starting throw it away later in the CPU online callback. But that's a
horrible hack and not required at all because RAPL becomes functional for
perf only in the CPU online callback. That's correct because user space is
not yet informed about the CPU being onlined, so nothing caan rely on RAPL
being available on that particular CPU.
Move the allocation to the CPU online callback and simplify the hotplug
handling. At this point the package mapping is established and correct.
This also adds a missing check for available package data in the
event_init() function.
Reported-by: Yasuaki Ishimatsu <yasu.isimatu@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 9d85eb9119 ("x86/smpboot: Make logical package management more robust")
Link: http://lkml.kernel.org/r/20170131230141.212593966@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit bf15f86b34 ("xtensa: initialize MMU before jumping to reset
vector") calls MMU management functions even when CONFIG_MMU is not
selected. That breaks noMMU build on cores with MMU.
Don't manage MMU when CONFIG_MMU is not selected.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
not migrate after the first instance. I found that there was as small
bug in the logic, and fixed it. It's minor, but should be fixed regardless.
There's not much impact outside the hwlat tracer.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJYkP7tFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
srEH/iqi0mC4rJF57yLmwGXVAuwSRsxHlkGfyG3RBRnXOhiPLaM9Y6QZDWj8f99D
DEnVJ7IMpW7tjJB0pDQBCMBi+NX6GvR9Zu4ub8k69UzDlw81CPdMiJ/HfEFsP5XA
EOiDH/xGsYmbgGyqbU2VTb4lS8CijStht0jhydriLT1ga/W3bOl0/w6TeQW+AwqJ
0tcksaKwAcH6iN11FUQfWPlirQ/aCTvj8FelgbT7MjYnwxDdbJSfKG+GwJjytLNQ
Rj/STWD56OZpl91OuEYA50BZVxp3eF870xJXsLjg3mGIYBseW/T6ZTP8TOM+6WoH
u2J08p8Owdtdo+9gkw+IwEuoFP4=
=VCLk
-----END PGP SIGNATURE-----
Merge tag 'trace-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"It was reported to me that the thread created by the hwlat tracer does
not migrate after the first instance. I found that there was as small
bug in the logic, and fixed it. It's minor, but should be fixed
regardless. There's not much impact outside the hwlat tracer"
* tag 'trace-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix hwlat kthread migration
2 patches to fix the oops Dave Hanse reported, plus a double kfree fix
Maarten discovered while backporting the fix for Linus.
For Linus' vma tracking oops the plan is to send you a dedicated pull with
the 2 patches we need, but since it's tricky we're letting CI beat on it a
bit more.
* tag 'drm-misc-fixes-2017-01-31' of git://anongit.freedesktop.org/git/drm-misc:
drm/atomic: Fix double free in drm_atomic_state_default_clear
drm: Don't race connector registration
drm: prevent double-(un)registration for connectors
Pull input subsystem fixes from Dmitry Torokhov:
"A fix for a crash in the wm97xx driver and synaptics-rmi4 will stop
throwing erroneous warnings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - fix reversed conditions in enable/disable_irq_wake
Input: wm97xx - make missing platform data non-fatal
Pull cgroup fix from Tejun Heo:
"The cgroup creation path was getting the order of operations wrong and
exposing cgroups which don't have their names set yet to controllers
which can lead to NULL derefs.
This contains the fix for the bug"
* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: don't online subsystems before cgroup_name/path() are operational
Pull percpu fix from Tejun Heo:
"Douglas found and fixed a ref leak bug in percpu_ref_tryget[_live]().
The bug is caused by storing the return value of atomic_long_inc_not_zero()
into an int temp variable before returning it as a bool. The interim
cast to int loses the upper bits and can lead to false negatives. As
percpu_ref uses a high bit to mark a draining counter, this can happen
relatively easily.
Fixed by using bool for the temp variable"
* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu-refcount: fix reference leak during percpu-atomic transition
Pull libata fixes from Tejun Heo:
"Three libata fixes: an error handling fix, blacklist addition for
another fallout from upping the default max sectors, and fix for a
sense data reporting bug which affects new harddrives which can report
sense data"
* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv:- Handle return value of devm_ioremap.
libata: Fix ATA request sense
libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices
Pull HID fixes from Jiri Kosina:
- regression fix (sleeping while atomic) for cp2112, from Johan Hovold
- regression fix for proximity handling under certain circumstances in
Wacom driver, from Jason Gerecke
- functional fix for Logitech Rumblepad 2, from Ardinartsev Nikita
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix gpio-callback error handling
HID: cp2112: fix sleep-while-atomic
HID: hid-lg: Fix immediate disconnection of Logitech Rumblepad 2
HID: usbhid: Quirk a AMI virtual mouse and keyboard with ALWAYS_POLL
HID: wacom: Fix poor prox handling in 'wacom_pl_irq'
Erik reported that on a preproduction hardware a CMCI storm triggers the
BUG_ON in add_timer_on(). The reason is that the per CPU MCE timer is
started by the CMCI logic before the MCE CPU hotplug callback starts the
timer with add_timer_on(). So the timer is already queued which triggers
the BUG.
Using add_timer_on() is pretty pointless in this code because the timer is
strictlty per CPU, initialized as pinned and all operations which arm the
timer happen on the CPU to which the timer belongs.
Simplify the whole machinery by using mod_timer() instead of add_timer_on()
which avoids the problem because mod_timer() can handle already queued
timers. Use __start_timer() everywhere so the earliest armed expiry time is
preserved.
Reported-by: Erik Veijola <erik.veijola@intel.com>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701310936080.3457@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We never use the irq2dev[] array so we can remove this assignment.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a couple of minor race/regression fixes, nothing exciting, but
somewhat important
* 'linux-4.10' of git://github.com/skeggsb/linux:
drm/nouveau/kms/nv50: request vblank events for commits that send completion events
drm/nouveau/nv1a,nv1f/disp: fix memory clock rate retrieval
drm/nouveau/disp/gt215: Fix HDA ELD handling (thus, HDMI audio) on gt215
drm/nouveau/nouveau/led: prevent compiling the led-code if nouveau=y and leds=m
drm/nouveau/disp/mcp7x: disable dptmds workaround
drm/nouveau: prevent userspace from deleting client object
drm/nouveau/fence/g84-: protect against concurrent access to semaphore buffers
The recent commit which prevents double activation of interrupts unearthed
interesting code in x86. The code (ab)uses irq_domain_activate_irq() to
reconfigure an already activated interrupt. That trips over the prevention
code now.
Fix it by deactivating the interrupt before activating the new configuration.
Fixes: 08d85f3ea9 "irqdomain: Avoid activating interrupts more than once"
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701311901580.3457@nanos
Under some circumstances, an fscache object can become queued such that it
fscache_object_work_func() can be called once the object is in the
OBJECT_DEAD state. This results in the kernel oopsing when it tries to
invoke the handler for the state (which is hard coded to 0x2).
The way this comes about is something like the following:
(1) The object dispatcher is processing a work state for an object. This
is done in workqueue context.
(2) An out-of-band event comes in that isn't masked, causing the object to
be queued, say EV_KILL.
(3) The object dispatcher finishes processing the current work state on
that object and then sees there's another event to process, so,
without returning to the workqueue core, it processes that event too.
It then follows the chain of events that initiates until we reach
OBJECT_DEAD without going through a wait state (such as
WAIT_FOR_CLEARANCE).
At this point, object->events may be 0, object->event_mask will be 0
and oob_event_mask will be 0.
(4) The object dispatcher returns to the workqueue processor, and in due
course, this sees that the object's work item is still queued and
invokes it again.
(5) The current state is a work state (OBJECT_DEAD), so the dispatcher
jumps to it - resulting in an OOPS.
When I'm seeing this, the work state in (1) appears to have been either
LOOK_UP_OBJECT or CREATE_OBJECT (object->oob_table is
fscache_osm_lookup_oob).
The window for (2) is very small:
(A) object->event_mask is cleared whilst the event dispatch process is
underway - though there's no memory barrier to force this to the top
of the function.
The window, therefore is from the time the object was selected by the
workqueue processor and made requeueable to the time the mask was
cleared.
(B) fscache_raise_event() will only queue the object if it manages to set
the event bit and the corresponding event_mask bit was set.
The enqueuement is then deferred slightly whilst we get a ref on the
object and get the per-CPU variable for workqueue congestion. This
slight deferral slightly increases the probability by allowing extra
time for the workqueue to make the item requeueable.
Handle this by giving the dead state a processor function and checking the
for the dead state address rather than seeing if the processor function is
address 0x2. The dead state processor function can then set a flag to
indicate that it's occurred and give a warning if it occurs more than once
per object.
If this race occurs, an oops similar to the following is seen (note the RIP
value):
BUG: unable to handle kernel NULL pointer dereference at 0000000000000002
IP: [<0000000000000002>] 0x1
PGD 0
Oops: 0010 [#1] SMP
Modules linked in: ...
CPU: 17 PID: 16077 Comm: kworker/u48:9 Not tainted 3.10.0-327.18.2.el7.x86_64 #1
Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 12/27/2015
Workqueue: fscache_object fscache_object_work_func [fscache]
task: ffff880302b63980 ti: ffff880717544000 task.ti: ffff880717544000
RIP: 0010:[<0000000000000002>] [<0000000000000002>] 0x1
RSP: 0018:ffff880717547df8 EFLAGS: 00010202
RAX: ffffffffa0368640 RBX: ffff880edf7a4480 RCX: dead000000200200
RDX: 0000000000000002 RSI: 00000000ffffffff RDI: ffff880edf7a4480
RBP: ffff880717547e18 R08: 0000000000000000 R09: dfc40a25cb3a4510
R10: dfc40a25cb3a4510 R11: 0000000000000400 R12: 0000000000000000
R13: ffff880edf7a4510 R14: ffff8817f6153400 R15: 0000000000000600
FS: 0000000000000000(0000) GS:ffff88181f420000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000002 CR3: 000000000194a000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffffa0363695 ffff880edf7a4510 ffff88093f16f900 ffff8817faa4ec00
ffff880717547e60 ffffffff8109d5db 00000000faa4ec18 0000000000000000
ffff8817faa4ec18 ffff88093f16f930 ffff880302b63980 ffff88093f16f900
Call Trace:
[<ffffffffa0363695>] ? fscache_object_work_func+0xa5/0x200 [fscache]
[<ffffffff8109d5db>] process_one_work+0x17b/0x470
[<ffffffff8109e4ac>] worker_thread+0x21c/0x400
[<ffffffff8109e290>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5acf>] kthread+0xcf/0xe0
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
[<ffffffff816460d8>] ret_from_fork+0x58/0x90
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeremy McNicoll <jeremymc@redhat.com>
Tested-by: Frank Sorenson <sorenson@redhat.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fscache_disable_cookie() needs to clear the outstanding writes on the
cookie it's disabling because they cannot be completed after.
Without this, fscache_nfs_open_file() gets stuck because it disables the
cookie when the file is opened for writing but can't uncache the pages till
afterwards - otherwise there's a race between the open routine and anyone
who already has it open R/O and is still reading from it.
Looking in /proc/pid/stack of the offending process shows:
[<ffffffffa0142883>] __fscache_wait_on_page_write+0x82/0x9b [fscache]
[<ffffffffa014336e>] __fscache_uncache_all_inode_pages+0x91/0xe1 [fscache]
[<ffffffffa01740fa>] nfs_fscache_open_file+0x59/0x9e [nfs]
[<ffffffffa01ccf41>] nfs4_file_open+0x17f/0x1b8 [nfsv4]
[<ffffffff8117350e>] do_dentry_open+0x16d/0x2b7
[<ffffffff811743ac>] vfs_open+0x5c/0x65
[<ffffffff81184185>] path_openat+0x785/0x8fb
[<ffffffff81184343>] do_filp_open+0x48/0x9e
[<ffffffff81174710>] do_sys_open+0x13b/0x1cb
[<ffffffff811747b9>] SyS_open+0x19/0x1b
[<ffffffff81001c44>] do_syscall_64+0x80/0x17a
[<ffffffff8165c2da>] return_from_SYSCALL_64+0x0/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Reported-by: Jianhong Yin <jiyin@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Initialise the stores_lock in fscache netfs cookies. Technically, it
shouldn't be necessary, since the netfs cookie is an index and stores no
data, but initialising it anyway adds insignificant overhead.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ip6_make_flowlabel() determines the flow label for IPv6 packets. It's
supposed to be passed a flow label, which it returns as is if non-0 and
in some other cases, otherwise it calculates a new value.
The problem is callers often pass a flowi6.flowlabel, which may also
contain traffic class bits. If the traffic class is non-0
ip6_make_flowlabel() mistakes the non-0 it gets as a flow label and
returns the whole thing. Thus it can return a 'flow label' longer than
20b and the low 20b of that is typically 0 resulting in packets with 0
label. Moreover, different packets of a flow may be labeled differently.
For a TCP flow with ECN non-payload and payload packets get different
labels as exemplified by this pair of consecutive packets:
(pure ACK)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
.... .... .... 0001 1100 1110 0100 1001 = Flow Label: 0x1ce49
Payload Length: 32
Next Header: TCP (6)
(payload)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
.... .... .... 0000 0000 0000 0000 0000 = Flow Label: 0x00000
Payload Length: 688
Next Header: TCP (6)
This patch allows ip6_make_flowlabel() to be passed more than just a
flow label and has it extract the part it really wants. This was simpler
than modifying the callers. With this patch packets like the above become
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
.... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
Payload Length: 32
Next Header: TCP (6)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
.... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
Payload Length: 688
Next Header: TCP (6)
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following smatch and coccinelle warnings:
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]
Fixes: 6465859aba ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olga Kornievskaia says: "I ran into this oops in the nfsd (below)
(4.10-rc3 kernel). To trigger this I had a client (unsuccessfully) try
to mount the server with krb5 where the server doesn't have the
rpcsec_gss_krb5 module built."
The problem is that rsci.cred is copied from a svc_cred structure that
gss_proxy didn't properly initialize. Fix that.
[120408.542387] general protection fault: 0000 [#1] SMP
...
[120408.565724] CPU: 0 PID: 3601 Comm: nfsd Not tainted 4.10.0-rc3+ #16
[120408.567037] Hardware name: VMware, Inc. VMware Virtual =
Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[120408.569225] task: ffff8800776f95c0 task.stack: ffffc90003d58000
[120408.570483] RIP: 0010:gss_mech_put+0xb/0x20 [auth_rpcgss]
...
[120408.584946] ? rsc_free+0x55/0x90 [auth_rpcgss]
[120408.585901] gss_proxy_save_rsc+0xb2/0x2a0 [auth_rpcgss]
[120408.587017] svcauth_gss_proxy_init+0x3cc/0x520 [auth_rpcgss]
[120408.588257] ? __enqueue_entity+0x6c/0x70
[120408.589101] svcauth_gss_accept+0x391/0xb90 [auth_rpcgss]
[120408.590212] ? try_to_wake_up+0x4a/0x360
[120408.591036] ? wake_up_process+0x15/0x20
[120408.592093] ? svc_xprt_do_enqueue+0x12e/0x2d0 [sunrpc]
[120408.593177] svc_authenticate+0xe1/0x100 [sunrpc]
[120408.594168] svc_process_common+0x203/0x710 [sunrpc]
[120408.595220] svc_process+0x105/0x1c0 [sunrpc]
[120408.596278] nfsd+0xe9/0x160 [nfsd]
[120408.597060] kthread+0x101/0x140
[120408.597734] ? nfsd_destroy+0x60/0x60 [nfsd]
[120408.598626] ? kthread_park+0x90/0x90
[120408.599448] ret_from_fork+0x22/0x30
Fixes: 1d658336b0 "SUNRPC: Add RPC based upcall mechanism for RPCGSS auth"
Cc: stable@vger.kernel.org
Cc: Simo Sorce <simo@redhat.com>
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Tested-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Both the NFS protocols and the Linux VFS use a setattr operation with a
bitmap of attributs to set to set various file attributes including the
file size and the uid/gid.
The Linux syscalls never mixes size updates with unrelated updates like
the uid/gid, and some file systems like XFS and GFS2 rely on the fact
that truncates might not update random other attributes, and many other
file systems handle the case but do not update the different attributes
in the same transaction. NFSD on the other hand passes the attributes
it gets on the wire more or less directly through to the VFS, leading to
updates the file systems don't expect. XFS at least has an assert on
the allowed attributes, which caught an unusual NFS client setting the
size and group at the same time.
To handle this issue properly this switches nfsd to call vfs_truncate
for size changes, and then handle all other attributes through
notify_change. As a side effect this also means less boilerplace code
around the size change as we can now reuse the VFS code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
nfsd assigns the nfs4_free_lock_stateid to .sc_free in init_lock_stateid().
If nfsd doesn't go through init_lock_stateid() and put stateid at end,
there is a NULL reference to .sc_free when calling nfs4_put_stid(ns).
This patch let the nfs4_stid.sc_free assignment to nfs4_alloc_stid().
Cc: stable@vger.kernel.org
Fixes: 356a95ece7 "nfsd: clean up races in lock stateid searching..."
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The hwlat tracer creates a kernel thread at start of the tracer. It is
pinned to a single CPU and will move to the next CPU after each period of
running. If the user modifies the migration thread's affinity, it will not
change after that happens.
The original code created the thread at the first instance it was called,
but later was changed to destroy the thread after the tracer was finished,
and would not be created until the next instance of the tracer was
established. The code that initialized the affinity was only called on the
initial instantiation of the tracer. After that, it was not initialized, and
the previous affinity did not match the current newly created one, making
it appear that the user modified the thread's affinity when it did not, and
the thread failed to migrate again.
Cc: stable@vger.kernel.org
Fixes: 0330f7aa8e ("tracing: Have hwlat trace migrate across tracing_cpumask CPUs")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In case of a zero-length report, the gpio direction_input callback would
currently return success instead of an errno.
Fixes: 1ffb3c40ff ("HID: cp2112: make transfer buffers DMA capable")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent commit fixing DMA-buffers on stack added a shared transfer
buffer protected by a spinlock. This is broken as the USB HID request
callbacks can sleep. Fix this up by replacing the spinlock with a mutex.
Fixes: 1ffb3c40ff ("HID: cp2112: make transfer buffers DMA capable")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices. This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.
This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: <stable@vger.kernel.org>
This somehow fixes an issue where sync-to-vblank longer works correctly
after resume from suspend.
From a HW perspective, we don't need the IRQs turned on to be able to
detect flip completion, so it's assumed that this is required for the
voodoo in the core DRM vblank core.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Based on the xf86-video-nv code, NFORCE (NV1A) and NFORCE2 (NV1F) have a
different way of retrieving clocks. See the
nv_hw.c:nForceUpdateArbitrationSettings function in the original code
for how these clocks were accessed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54587
Cc: stable@vger.kernel.org
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Store the ELD correctly, not just enough copies of the first byte
to pad out the given ELD size.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Fixes: 120b0c39c7 ("drm/nv50-/disp: audit and version SOR_HDA_ELD method")
Cc: stable@vger.kernel.org # v3.17+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The proper fix would have been to select LEDS_CLASS but this can lead
to a circular dependency, as found out by Arnd.
This patch implements Arnd's suggestion instead, at the cost of some
auto-magic for a fringe feature.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Intel's 0-DAY
Fixes: 8d021d71b3 ("drm/nouveau/drm/nouveau: add a LED driver for the NVIDIA logo")
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The workaround appears to cause regressions on these boards, and from
inspection of RM traces, NVIDIA don't appear to do it on them either.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Roy Spliet <nouveau@spliet.org>
Commit a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
added the proper mb(), but removed the test "prev_write_sz < pending_sz"
when making the signal decision.
As a result, the guest can signal the host unnecessarily,
and then the host can throttle the guest because the host
thinks the guest is buggy or malicious; finally the user
running stress test can perceive intermittent freeze of
the guest.
This patch brings back the test, and properly handles the
in-place consumption APIs used by NetVSC (see get_next_pkt_raw(),
put_pkt_raw() and commit_rd_index()).
Fixes: a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These tests are reversed. A warning should be displayed if an error is
returned, not on success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull sparc fixes from David Miller:
"Several small bug fixes and tidies, along with a fix for non-resumable
memory errors triggered by userspace"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Handle PIO & MEM non-resumable errors.
sparc64: Zero pages on allocation for mondo and error queues.
sparc: Fixed typo in sstate.c. Replaced panicing with panicking
sparc: use symbolic names for tsb indexing
Liam R. Howlett says:
====================
sparc64: Recover from userspace non-resumable PIO & MEM errors
A non-resumable error from userspace is able to cause a kernel panic or trap
loop due to the setup and handling of the queued traps once in the kernel.
This patch series addresses both of these issues.
The queues are fixed by simply zeroing the memory before use.
PIO errors from userspace will result in a SIGBUS being sent to the user
process.
The MEM errors form userspace will result in a SIGKILL and also cause the
offending pages to be claimed so they are no longer used in future tasks.
SIGKILL is used to ensure that the process does not try to coredump and result
in an attempt to read the memory again from within kernel space. Although
there is a HV call to scrub the memory (mem_scrub), there is no easy way to
guarantee that the real memory address(es) are not used by other tasks.
Clearing the error with mem_scrub would zero the memory and cause the other
processes to proceed with bad data.
The handling of other non-resumable errors remain unchanged and will cause a
panic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
