On Asrock Z370M Pro4, it was observed that EC access was disabled after
initially booting the system. As a result, the driver failed to load
with
nct6683: EC is disabled
After a suspend/resume cycle, the driver loaded correctly.
nct6683: Found NCT6683D or compatible chip at 0x2e:0xa20
nct6683 nct6683.2592: NCT6683D EC firmware version 1.0 build 07/18/16
Enable EC access after identifying the chip if disabled to fix the problem.
Warn the user that the data it reports may be unusable, similar to other
drivers for chips from Nuvoton.
Fixes: 41082d66bf ("hwmon: Driver for NCT6683D")
Reported-by: Jonathan Sims <jonathan.625266@earthlink.net>
Tested-by: Jonathan Sims <jonathan.625266@earthlink.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Postpone calling virt_to_page() translation on memory locations not
guaranteed to be backed by a struct page. Try first to map memory from
the device coherent memory pool, then perform translation if that fails.
On some architectures, specifically SH when configured with the SPARSEMEM
memory model, assuming a struct page is always assigned to a memory
address lead to unexpected hangs during the virtual to page address
translation. This patch fixes that specific issue but applies in the
general case too.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The use of "correctly mapped" here is misleading, since it can give the
wrong expectation in the case that the memory *should* have been mapped
from the per-device pool, but doing so failed for other reasons.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When an allocation with lower dma_coherent mask fails, dma_direct_alloc()
retries the allocation with GFP_DMA. But, this is useless for
architectures that hav no ZONE_DMA.
Fix it by adding the check of CONFIG_ZONE_DMA before retrying the
allocation.
Fixes: 95f183916d ("dma-direct: retry allocations using GFP_DMA for small masks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a driver uses DPM_FLAG_SMART_SUSPEND and the device is already
runtime suspended when hibernate is started PCI core skips runtime
resuming the device but still clears pci_dev->state_saved. After the
hibernation image is written pci_pm_thaw_noirq() makes sure subsequent
thaw phases for the device are also skipped leaving it runtime suspended
with pci_dev->state_saved == false.
When the device is eventually runtime resumed pci_pm_runtime_resume()
restores config space by calling pci_restore_standard_config(), however
because pci_dev->state_saved == false pci_restore_state() never actually
restores the config space leaving the device in a state that is not what
the driver might expect.
For example here is what happens for intel-lpss I2C devices once the
hibernation snapshot is taken:
intel-lpss 0000:00:15.0: power state changed by ACPI to D0
intel-lpss 0000:00:1e.0: power state changed by ACPI to D3cold
video LNXVIDEO:00: Restoring backlight state
PM: hibernation exit
i2c_designware i2c_designware.1: Unknown Synopsys component type: 0xffffffff
i2c_designware i2c_designware.0: Unknown Synopsys component type: 0xffffffff
i2c_designware i2c_designware.1: timeout in disabling adapter
i2c_designware i2c_designware.0: timeout in disabling adapter
Since PCI config space is not restored the device is still in D3hot
making MMIO register reads return 0xffffffff.
Fix this by clearing pci_dev->state_saved only if we actually end up
runtime resuming the device.
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At least on one Dell system the PNP motherboard resources device
includes resources used by WDAT table. Since PNP gets initialized before
WDAT it results following error and no watchdog:
platform wdat_wdt: failed to claim resource 3: [io 0x046a-0x046c]
ACPI: watchdog: Device creation failed: -16
Now, the PNP system driver is already accustomed with the situation that
it cannot reserve all those motherboard resources because drivers using
those might have reserved them already. In addition putting WDAT table
resources under motherboard resources device makes sense in general.
Fix this by initializing WDAT right before PNP. This allows WDAT to
reserve all its resources and still keeps PNP system driver happy.
Reported-by: Shubhrata.Priyadarsh@dell.com
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ThinkPad X1 Tablet(2016) is reported to have issues with
the Low Power S0 Idle _DSM interface and since this machine
model generally can do ACPI S3 just fine, and user would
like to use S3 as default sleep model, add a blacklist
entry to disable that interface for ThinkPad X1 Tablet(2016).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199057
Reported-and-tested-by: Robin Lee <robinlee.sysu@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The main linker script vmlinux.lds.S for the kernel image merges
the expoline code patch tables into two section ".nospec_call_table"
and ".nospec_return_table". This is *not* done for the modules,
there the sections retain their original names as generated by gcc:
".s390_indirect_call", ".s390_return_mem" and ".s390_return_reg".
The module_finalize code has to check for the compiler generated
section names, otherwise no code patching is done. This slows down
the module code in case of "spectre_v2=off".
Cc: stable@vger.kernel.org # 4.16
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we call ssch, an interrupt might already be pending once we
return from the START SUBCHANNEL instruction. Therefore we need to
make sure interrupts are disabled while holding the subchannel lock
until after we're done with our processing.
Cc: stable@vger.kernel.org #v4.12+
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In a multi-threaded program any thread can call execve(). If this
is not done by the thread group leader, the de_thread() function
replaces the pid of the task that calls execve() with the pid of
thread group leader. If the task reaches user space again without
going over __switch_to() the sampling tag is still set to the old
pid.
Define the arch_setup_new_exec function to verify the task pid
and udpate the tag with LPP if it has changed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the IBM z13/z14 counter names to be in sync with all other models.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 3593eb944c ("s390/cpum_cf: add hardware counter support for IBM z14")
Fixes: 3fc7acebae ("s390/cpum_cf: add IBM z13 counter event names")
Signed-off-by: André Wild <wild@linux.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a new CKD storage volume is defined at the storage server, Linux
may be relying on outdated information about that volume, which leads to
the following errors:
1. Command Reject Errors for minidisk on z/VM:
dasd-eckd.b3193d: 0.0.XXXX: An error occurred in the DASD device driver,
reason=09
dasd(eckd): I/O status report for device 0.0.XXXX:
dasd(eckd): in req: 00000000XXXXXXXX CC:00 FC:04 AC:00 SC:17 DS:02 CS:00
RC:0
dasd(eckd): device 0.0.2046: Failing CCW: 00000000XXXXXXXX
dasd(eckd): Sense(hex) 0- 7: 80 00 00 00 00 00 00 00
dasd(eckd): Sense(hex) 8-15: 00 00 00 00 00 00 00 00
dasd(eckd): Sense(hex) 16-23: 00 00 00 00 e1 00 0f 00
dasd(eckd): Sense(hex) 24-31: 00 00 40 e2 00 00 00 00
dasd(eckd): 24 Byte: 0 MSG 0, no MSGb to SYSOP
2. Equipment Check errors on LPAR or for dedicated devices on z/VM:
dasd(eckd): I/O status report for device 0.0.XXXX:
dasd(eckd): in req: 00000000XXXXXXXX CC:00 FC:04 AC:00 SC:17 DS:0E CS:40
fcxs:01 schxs:00 RC:0
dasd(eckd): device 0.0.9713: Failing TCW: 00000000XXXXXXXX
dasd(eckd): Sense(hex) 0- 7: 10 00 00 00 13 58 4d 0f
dasd(eckd): Sense(hex) 8-15: 67 00 00 00 00 00 00 04
dasd(eckd): Sense(hex) 16-23: e5 18 05 33 97 01 0f 0f
dasd(eckd): Sense(hex) 24-31: 00 00 40 e2 00 04 58 0d
dasd(eckd): 24 Byte: 0 MSG f, no MSGb to SYSOP
Fix this problem by using the up-to-date information provided during
online processing via the device specific SNEQ to detect the case of
outdated LCU data. If there is a difference, perform a re-read of that
data.
Cc: stable@vger.kernel.org
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement s390 specific arch_uretprobe_is_alive() to avoid SIGSEGVs
observed with uretprobes in combination with setjmp/longjmp.
See commit 2dea1d9c38 ("powerpc/uprobes: Implement
arch_uretprobe_is_alive()") for more details.
With this implemented all test cases referenced in the above commit
pass.
Reported-by: Ziqian SUN <zsun@redhat.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Channel path descriptors have been seen as something stable (as
long as the chpid is configured). Recent tests have shown that the
descriptor can also be altered when the link state of a channel path
changes. Thus it is necessary to update the descriptor during
handling of resource accessibility events.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loop checks for non-zero count of sensors for each type
of sensors which is completely wrong. It also results in aborting the
registration of sensors if one or more types of sensors are completely
not supported by the platform SCMI firmware.
This patch fixes the issue by continue to loop and skiping sensor types
that are not present.
Fixes: b23688aefb ("hwmon: add support for sensors exported via ARM SCMI")
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-21
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a deadlock between mm->mmap_sem and bpf_event_mutex when
one task is detaching a BPF prog via perf_event_detach_bpf_prog()
and another one dumping through bpf_prog_array_copy_info(). For
the latter we move the copy_to_user() out of the bpf_event_mutex
lock to fix it, from Yonghong.
2) Fix test_sock and test_sock_addr.sh failures. The former was
hitting rlimit issues and the latter required ping to specify
the address family, from Yonghong.
3) Remove a dead check in sockmap's sock_map_alloc(), from Jann.
4) Add generated files to BPF kselftests gitignore that were previously
missed, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
net: sched: ife: malformed ife packet fixes
As promised at netdev 2.2 tc workshop I am working on adding scapy support for
tdc testing. It is still work in progress. I will submit the patches to tdc
later (they are not in good shape yet). The good news is I have been able to
find bugs which normal packet testing would not be able to find.
With fuzzy testing I was able to craft certain malformed packets that IFE
action was not able to deal with. This patch set fixes those bugs.
changes since v4:
- use pskb_may_pull before pointer assign
changes since v3:
- use pskb_may_pull
changes since v2:
- remove inline from __ife_tlv_meta_valid
- add const to cast to meta_tlvhdr
- add acked and reviewed tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks if sk buffer is available to dererence ife header. If
not then NULL will returned to signal an malformed ife packet. This
avoids to crashing the kernel from outside.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no handling to check on a invalid tlv length. This
patch adds such handling to avoid killing the kernel with a malformed
ife packet.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to record stats for received metadata that we dont know how
to process. Have find_decode_metaid() return -ENOENT to capture this.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sock's sk_rcvtimeo is initialized to
LONG_MAX/MAX_SCHEDULE_TIMEOUT in sock_init_data. Calling
mod_delayed_work with a timeout of LONG_MAX causes spurious execution of
the work function. timer->expires is set equal to jiffies + LONG_MAX.
When timer_base->clk falls behind the current value of jiffies,
the delta between timer_base->clk and jiffies + LONG_MAX causes the
expiration to be in the past. Returning early from strp_start_timer if
timeo == LONG_MAX solves this problem.
Found while testing net/tls_sw recv path.
Fixes: 43a0c6751a ("strparser: Stream parser for messages")
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=SkQU
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos, i915, vc4, amdgpu fixes.
i915:
- an oops fix
- two race fixes
- some gvt fixes
amdgpu:
- dark screen fix
- clk/voltage fix
- vega12 smu fix
vc4:
- memory leak fix
exynos just drops some code"
* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/amd/powerplay: header file interface to SMU update
drm/amd/pp: Fix bug voltage can't be OD separately on VI
drm/amd/display: Don't program bypass on linear regamma LUT
drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
drm/i915/audio: Fix audio detection issue on GLK
drm/i915: Call i915_perf_fini() on init_hw error unwind
drm/i915/bios: filter out invalid DDC pins from VBT child devices
drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
drm/exynos: exynos_drm_fb -> drm_framebuffer
drm/exynos: Move dma_addr out of exynos_drm_fb
drm/exynos: Move GEM BOs to drm_framebuffer
drm: Fix HDCP downstream dev count read
drm/vc4: Fix memory leak during BO teardown
drm/i915/execlists: Clear user-active flag on preemption completion
drm/i915/gvt: Add drm_format_mod update
drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
drm/i915/gvt: Delete redundant error message in fb_decode.c
drm/i915/gvt: Cancel dma map when resetting ggtt entries
drm/i915/gvt: Missed to cancel dma map for ggtt entries
...
- Fix a dark screen issue in DC
- Fix clk/voltage dependency tracking for wattman
- Update SMU interface for vega12
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/powerplay: header file interface to SMU update
drm/amd/pp: Fix bug voltage can't be OD separately on VI
drm/amd/display: Don't program bypass on linear regamma LUT
relevant functions.
- it removes exynos_drm_fb structure which is a wrapper of
drm_framebuffer and unnecessary two exynos specific callback
functions, exynos_drm_destory() and exynos_drm_fb_create_handle()
because we can reuse existing drm common callback ones instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Bb/
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Remove Exynos specific framebuffer structure and
relevant functions.
- it removes exynos_drm_fb structure which is a wrapper of
drm_framebuffer and unnecessary two exynos specific callback
functions, exynos_drm_destory() and exynos_drm_fb_create_handle()
because we can reuse existing drm common callback ones instead.
* tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: exynos_drm_fb -> drm_framebuffer
drm/exynos: Move dma_addr out of exynos_drm_fb
drm/exynos: Move GEM BOs to drm_framebuffer
drm/amdkfd: Deallocate SDMA queues correctly
drm/amdkfd: Fix scratch memory with HWS enabled
- Fix for FDO #105549: Avoid OOPS on bad VBT (Jani)
- Fix rare pre-emption race (Chris)
- Fix RC6 race against PM transitions (Tvrtko)
* tag 'drm-intel-next-fixes-2018-04-19' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/audio: Fix audio detection issue on GLK
drm/i915: Call i915_perf_fini() on init_hw error unwind
drm/i915/bios: filter out invalid DDC pins from VBT child devices
drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
drm/i915/execlists: Clear user-active flag on preemption completion
drm/i915/gvt: Add drm_format_mod update
drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
drm/i915/gvt: Delete redundant error message in fb_decode.c
drm/i915/gvt: Cancel dma map when resetting ggtt entries
drm/i915/gvt: Missed to cancel dma map for ggtt entries
drm/i915/gvt: Make MI_USER_INTERRUPT nop in cmd parser
drm/i915/gvt: Mark expected switch fall-through in handle_g2v_notification
drm/i915/gvt: throw error on unhandled vfio ioctls
-----BEGIN PGP SIGNATURE-----
iQGwBAABCAAaBQJa2jQtExxzbWZyZW5jaEBnbWFpbC5jb20ACgkQiiy9cAdyT1Fb
AAv9FqmD7ElRfZAHBO1gFhOMojhGngf4VsdoKD7raFhkzQLJbEB/Vjjf0OQ6IeR9
EJ+yW7H7lLIifv+xFandBxhjFvg3H+HTFdOuAUk4zpffripOgyfIJeHmc0Lt3DDA
sGGsIcgl5wWXV9hEEtMGlUOoKeVfMKoDqOmIvtOUeSZ616G2NXSRM7ySnSX3KEQR
SJo+rI16P4OQbEZ3W5ElJE6otytKQF76cCoOdEuWLF5mSJfkaCiovrDw/VM2oXFF
C8Uu4cHJFDDxL2uPrYGFPGKWisi0K0G8Lq5q0nOQWC8Ajh9EgfGR667p3btEGQ0d
TPYLHaXleb45qtMUDq7JiPy3VTs5qvr5uJyQdB9s3E+M+9pq1bgQmIVymKJi9ccu
QbKospypFsz81t0DwB7/2TEVsh00Y6bcNIALTALUNntP/emeiQwLrwOkWb3PBlIf
WM0OJH1JJChvypDZ8n29wy2A2p1YIflrGghieONf2jG/dL7bUzssfMCXFxY2MVvf
GCUk
=lT4e
-----END PGP SIGNATURE-----
Merge tag '4.17-rc1-SMB3-CIFS' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Various SMB3/CIFS fixes.
There are three more security related fixes in progress that are not
included in this set but they are still being tested and reviewed, so
sending this unrelated set of smaller fixes now"
* tag '4.17-rc1-SMB3-CIFS' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: fix typo in cifs_dbg
cifs: do not allow creating sockets except with SMB1 posix exensions
cifs: smbd: Dump SMB packet when configured
cifs: smbd: Check for iov length on sending the last iov
fs: cifs: Adding new return type vm_fault_t
cifs: smb2ops: Fix NULL check in smb2_query_symlink
-----BEGIN PGP SIGNATURE-----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=lgaO
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"This contains a few fixups to the qgroup patches that were merged this
dev cycle, unaligned access fix, blockgroup removal corner case fix
and a small debugging output tweak"
* tag 'for-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: print-tree: debugging output enhancement
btrfs: Fix race condition between delayed refs and blockgroup removal
btrfs: fix unaligned access in readdir
btrfs: Fix wrong btrfs_delalloc_release_extents parameter
btrfs: delayed-inode: Remove wrong qgroup meta reservation calls
btrfs: qgroup: Use independent and accurate per inode qgroup rsv
btrfs: qgroup: Commit transaction in advance to reduce early EDQUOT
For SOCK_ZAPPED socket, we don't need to care about llc->sap,
so we should just skip these refcount functions in this case.
Fixes: f7e4367268 ("llc: hold llc_sap before release_sock()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connection timers of an llc sock could be still flying
after we delete them in llc_sk_free(), and even possibly
after we free the sock. We could just wait synchronously
here in case of troubles.
Note, I leave other call paths as they are, since they may
not have to wait, at least we can change them to synchronously
when needed.
Also, move the code to net/llc/llc_conn.c, which is apparently
a better place.
Reported-by: <syzbot+f922284c18ea23a8e457@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0e0c3fee3a ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
assumed that if pppol2tp_seq_stop() was called with non-NULL private
data (the 'v' pointer), then pppol2tp_seq_start() would not be called
again. It turns out that this isn't guaranteed, and overflowing the
seq_file's buffer in pppol2tp_seq_show() is a way to get into this
situation.
Therefore, pppol2tp_seq_stop() needs to reset pd->tunnel, so that
pppol2tp_seq_start() won't drop a reference again if it gets called.
We also have to clear pd->session, because the rest of the code expects
a non-NULL tunnel when pd->session is set.
The l2tp_debugfs module has the same issue. Fix it in the same way.
Fixes: 0e0c3fee3a ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
Fixes: f726214d9b ("l2tp: hold reference on tunnels printed in l2tp/tunnels debugfs file")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-04-19
Please apply the following qeth fixes for 4.17. The common theme
seems to be error handling improvements in various areas of cmd IO.
Patches 1-3 should also go back to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.
On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.
For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.
Fixes: ec61bd2fd2 ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.
Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.
This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.
Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.
Fixes: 0f54761d16 ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.
As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.
*Note: currently just one location in the code really handles this problem,
by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.
This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf6133 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Prevent X2APIC ID 0xFFFFFFFF from being treated as valid, which
causes the possible CPU count to be wrong.
- Prevent 32bit truncation in calc_hpet_ref() which causes the TSC
calibration to fail
- Fix the page table setup for temporary text mappings in the resume
code which causes resume failures
- Make the page table dump code handle HIGHPTE correctly instead of
oopsing
- Support for topologies where NUMA nodes share an LLC to prevent a
invalid topology warning and further malfunction on such systems.
- Remove the now unused pci-nommu code
- Remove stale function declarations"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/power/64: Fix page-table setup for temporary text mapping
x86/mm: Prevent kernel Oops in PTDUMP code with HIGHPTE=y
x86,sched: Allow topologies where NUMA nodes share an LLC
x86/processor: Remove two unused function declarations
x86/acpi: Prevent X2APIC id 0xffffffff from being accounted
x86/tsc: Prevent 32bit truncation in calc_hpet_ref()
x86: Remove pci-nommu.c
Pull timer fixes from Thomas Gleixner:
"A small set of timer fixes:
- Evaluate the -ETIME condition correctly in the imx tpm driver
- Fix the evaluation order of a condition in posix cpu timers
- Use pr_cont() in the clockevents code to prevent ugly message
splitting
- Remove __current_kernel_time() which is now unused to prevent that
new users show up.
- Remove a stale forward declaration"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/imx-tpm: Correct -ETIME return condition check
posix-cpu-timers: Ensure set_process_cpu_timer is always evaluated
timekeeping: Remove __current_kernel_time()
timers: Remove stale struct tvec_base forward declaration
clockevents: Fix kernel messages split across multiple lines
Pull perf fixes from Thomas Gleixner:
"A larger set of updates for perf.
Kernel:
- Handle the SBOX uncore monitoring correctly on Broadwell CPUs which
do not have SBOX.
- Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]. The
percentage of preempting and non-preempting context switches help
understanding the nature of workloads (CPU or IO bound) that are
running on a machine. This adds the kernel facility and userspace
changes needed to show this information in 'perf script' and 'perf
report -D' (Alexey Budankov)
- Remove a WARN_ON() in the trace/kprobes code which is pointless
because the return error code is already telling the caller what's
wrong.
- Revert a fugly workaround for clang BPF targets.
- Fix sample_max_stack maximum check and do not proceed when an error
has been detect, return them to avoid misidentifying errors (Jiri
Olsa)
- Add SPDX idenitifiers and get rid of GPL boilderplate.
Tools:
- Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)
- Support MAP_FIXED_NOREPLACE, noticed when updating the
tools/include/ copies (Arnaldo Carvalho de Melo)
- Add '\n' at the end of parse-options error messages (Ravi Bangoria)
- Add s390 support for detailed/verbose PMU event description (Thomas
Richter)
- perf annotate fixes and improvements:
* Allow showing offsets in more than just jump targets, use the
new 'O' hotkey in the TUI, config ~/.perfconfig
annotate.offset_level for it and for --stdio2 (Arnaldo Carvalho
de Melo)
* Use the resolved variable names from objdump disassembled lines
to make them more compact, just like was already done for some
instructions, like "mov", this eventually will be done more
generally, but lets now add some more to the existing mechanism
(Arnaldo Carvalho de Melo)
- perf record fixes:
* Change warning for missing topology sysfs entry to debug, as not
all architectures have those files, s390 being one of those
(Thomas Richter)
* Remove old error messages about things that unlikely to be the
root cause in modern systems (Andi Kleen)
- perf sched fixes:
* Fix -g/--call-graph documentation (Takuya Yamamoto)
- perf stat:
* Enable 1ms interval for printing event counters values in
(Alexey Budankov)
- perf test fixes:
* Run dwarf unwind on arm32 (Kim Phillips)
* Remove unused ptrace.h include from LLVM test, sidesteping older
clang's lack of support for some asm constructs (Arnaldo
Carvalho de Melo)
* Fixup BPF test using epoll_pwait syscall function probe, to cope
with the syscall routines renames performed in this development
cycle (Arnaldo Carvalho de Melo)
- perf version fixes:
* Do not print info about HAVE_LIBAUDIT_SUPPORT in 'perf version
--build-options' when HAVE_SYSCALL_TABLE_SUPPORT is true, as
libaudit won't be used in that case, print info about
syscall_table support instead (Jin Yao)
- Build system fixes:
* Use HAVE_..._SUPPORT used consistently (Jin Yao)
* Restore READ_ONCE() C++ compatibility in tools/include (Mark
Rutland)
* Give hints about package names needed to build jvmti (Arnaldo
Carvalho de Melo)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs
perf/x86/intel/uncore: Revert "Remove SBOX support for Broadwell server"
coresight: Move to SPDX identifier
perf test BPF: Fixup BPF test using epoll_pwait syscall function probe
perf tests mmap: Show which tracepoint is failing
perf tools: Add '\n' at the end of parse-options error messages
perf record: Remove suggestion to enable APIC
perf record: Remove misleading error suggestion
perf hists browser: Clarify top/report browser help
perf mem: Allow all record/report options
perf trace: Support MAP_FIXED_NOREPLACE
perf: Remove superfluous allocation error check
perf: Fix sample_max_stack maximum check
perf: Return proper values for user stack errors
perf list: Add s390 support for detailed/verbose PMU event description
perf script: Extend misc field decoding with switch out event type
perf report: Extend raw dump (-D) out with switch out event type
perf/core: Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]
tools/headers: Synchronize kernel ABI headers, v4.17-rc1
trace_kprobe: Remove warning message "Could not insert probe at..."
...
Pull objtool fix from Thomas Gleixner:
"A single fix for objtool so it uses the host C and LD flags and not
the target ones"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Support HOSTCFLAGS and HOSTLDFLAGS
unblock earlier than designed. Thanks to Jann Horn from Google's
Project Zero for pointing this out to me.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlrcCWAACgkQ8vlZVpUN
gaOedwf/e1OU7CXMiinCcGfsr5XydZrEivaqS9QmqAKsLzJSNDDu1Jw6N9cbWagp
OEIIRZdaFPImZHosEbjOW12Z3nxnlDC8jtOLyLIRGSA2u4RXd03RupHhQW4cE7ys
EOljEvK5KFDIlPa947R5/k4CzC4O3PGf1GdWhHmkENOgd23GqI/yOTKQq5Z5ZgAp
rZzcXiuCSq1QkLME7ElxoOLQhs+fYiVGoAM/maxLa+2g4M1Y/YlHBDGhG4RB4lLA
3zugbyJ15tNfgNuRvCB4x304WkCp5VDlcsCiKq18LFcrkz1SYGj5LwG/bswDqgkS
0mOtZKu68NhutX8Pcy4vY3iOmMa1/Q==
=RhHb
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fixes from Ted Ts'o:
"Fix some bugs in the /dev/random driver which causes getrandom(2) to
unblock earlier than designed.
Thanks to Jann Horn from Google's Project Zero for pointing this out
to me"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add new ioctl RNDRESEEDCRNG
random: crng_reseed() should lock the crng instance that it is modifying
random: set up the NUMA crng instances after the CRNG is fully initialized
random: use a different mixing algorithm for add_device_randomness()
random: fix crng_ready() test
Pull libnvdimm fixes from Dan Williams:
"A regression fix, new unit test infrastructure and a build fix:
- Regression fix addressing support for the new NVDIMM label storage
area access commands (_LSI, _LSR, and _LSW).
The Intel specific version of these commands communicated the
"Device Locked" status on the label-storage-information command.
However, these new commands (standardized in ACPI 6.2) communicate
the "Device Locked" status on the label-storage-read command, and
the driver was missing the indication.
Reading from locked persistent memory is similar to reading
unmapped PCI memory space, returns all 1's.
- Unit test infrastructure is added to regression test the "Device
Locked" detection failure.
- A build fix is included to allow the "of_pmem" driver to be built
as a module and translate an Open Firmware described device to its
local numa node"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
MAINTAINERS: Add backup maintainers for libnvdimm and DAX
device-dax: allow MAP_SYNC to succeed
Revert "libnvdimm, of_pmem: workaround OF_NUMA=n build error"
libnvdimm, of_pmem: use dev_to_node() instead of of_node_to_nid()
tools/testing/nvdimm: enable labels for nfit_test.1 dimms
tools/testing/nvdimm: fix missing newline in nfit_test_dimm 'handle' attribute
tools/testing/nvdimm: support nfit_test_dimm attributes under nfit_test.1
tools/testing/nvdimm: allow custom error code injection
libnvdimm, dimm: handle EACCES failures from label reads
A few small fixes:
- A fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- A long-standing bug fix in LINE6 MIDI
-----BEGIN PGP SIGNATURE-----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=fb42
-----END PGP SIGNATURE-----
Merge tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small fixes:
- a fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- a long-standing bug fix in LINE6 MIDI"
* tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: rawmidi: Fix missing input substream checks in compat ioctls
ALSA: hda/realtek - adjust the location of one mic
ALSA: hda/realtek - set PINCFG_HEADSET_MIC to parse_flags
ALSA: hda - New VIA controller suppor no-snoop path
ALSA: line6: Use correct endpoint type for midi output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlrUXbEACgkQ+iyteGJfRsoSSgCglHHxe51pHR+p395z2KdBEJAm
5CEAn0SNfw6PZw6F+P19yh4WBmT2QO6P
=bKNy
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-4.17-rc2' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- fall-through fixes
- MAINTAINER change for hpwdt
- renesas-wdt: Add support for WDIOF_CARDRESET
- aspeed: set bootstatus during probe
* tag 'linux-watchdog-4.17-rc2' of git://www.linux-watchdog.org/linux-watchdog:
aspeed: watchdog: Set bootstatus during probe
watchdog: renesas-wdt: Add support for WDIOF_CARDRESET
watchdog: wafer5823wdt: Mark expected switch fall-through
watchdog: w83977f_wdt: Mark expected switch fall-through
watchdog: sch311x_wdt: Mark expected switch fall-through
watchdog: hpwdt: change maintainer.
