The nvram arbitration rules were not strictly followed in a few places
and this could lead to reading corrupted values from the nvram.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- TSO workaround
- Fixes eeprom version reporting
- Fix loopback test
- Fix for WOL
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Get rid of warning in case of race with ring full and lockless
tx on the skge driver. It is possible to be in the transmit
routine with no available slots and already stopped.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The CSR contains garbage after a coldboot on RS/6000.
One some systems (like my 44p 270) the MAC address is all FF,
on others (like my B50) it is ff:ff:ff:fd:ff:6b.
It can eventually be fixed by loading pcnet32, set the interface
into the UP state, rmmod pcnet32 and load it again. But this worked
only on the 270.
Only netbooting after a cold start provides the correct MAC address
via prom and CSR. This makes it very unreliable.
I dont know why the MAC is stored in two different places. Remove
the special case for powerpc, which was added in early 2.4 development.
Signed-off-by: Olaf Hering <olh@suse.de>
drivers/net/pcnet32.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change version number. Still don't have enough history on this
to call it 1.0 yet.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Under load, my SysKonnect SK-9S22 sees duplicate checksums from
earlier packets. Doesn't happen on other platforms so just disable
receive checksum there.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Turn symmetric flow control on by default. This was an oversight
in the initial versions.
Signed-off-by: Stephen HEmminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a couple more prefetches to where we walk the rings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Put more logic in to try and handle transmit timeout recovery.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adjust interrupt deferral values for better performance and avoid
starvation issues under stress.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Optimize poll routine by not clearing interrupt till after
processing, and checking for more work before re-enable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change transmit complete handling to use the status values
in the poll list because they are in-cache, rather than reading
non-cached memory for chips status.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some transmit side small fixes:
* When computing number of list elements per transmit, do full
comparision to check for checksuming.
* Get rid of racy check for tx_complete
* Change stop test to match wake condition.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Split Tx and Rx ring into two different data structures.
Tx needs the next value (to handle partial status), and
Rx always needs the mapaddr (to handle resubmitting same buffer).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to keep track of mapping length in ring structure
because we can get the same info from other info.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to disable interrupts during the transmit routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do phy processing in a work queue rather than a tasklet.
This means we can let bottom halves run.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for get/set the interrupt coalescing settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make the copy threshold a module parameter for those who
may want to turn it off.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It is a useful optimization to rearrange the structure
slightly to align receive and transmit portions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There maybe new versions of Yukon2 in the future, so make the
driver more robust to handle this.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum offsets for receive offload were not being set correctly.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
One of the rearrangements dropped this and it means
sky2 spins in napi/interrupt.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sky2 update changed name of netif_schedule_test to __netif_schedule_prep
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There are currently two IPW_DEBUG options in drivers/net/wireless/Kconfig
(one for ipw2100 and one for ipw2200). The attached patch splits it into
IPW2100_DEBUG and IPW2200_DEBUG.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: "James P. Ketrenos" <ipw2100-admin@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Use kzalloc for IPW2200
- Fix config dependency for IPW2200
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hello Jeff,
this patch changes causes the airo driver to not reset the card when a
temporary WEP key is set, when the IW_ENCODE_TEMP flag is used. This is
needed for xsupplicant as 802.1x, LEAP, etc. change WEP keys frequently
after authentication and resetting the card causes infinite
reauthentication.
Javier and Jean agree with the patch, Javier suggested I send this to
you, can you apply this?
Thanks.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
without this patch after an rmmod, modprobe the card won't work anymore
until the next reboot.
This patch seem safe to apply for all cards as the bsd driver already do
that.
I had to add a timeout because strange things happen (issuecommand will
fail) if the card is already reseted (after a reboot).
PS : it seems there are missing reset when leaving monitor mode...
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Power management parameters could not be set by iwconfig due to
incorrect error handling.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use platform_driver_unregister not driver_unregister to unregister a
struct platform_driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Disable/enable the SERDES carrier when an interface is administratively
downed/upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement pm3386 reset. A reset zeroes out the internally stored MAC
addresses, so we need to save and reload them by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a pm3386 hook for disabling/enabling the SERDES carrier, so that
we can disable it when the interface is administratively downed, and
enable it when it is upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When we reset the pm3386, it loses its internally stored MAC addresses
that were programmed into it by the bootloader (and are used by the
hardware for the generation of PAUSE frames.) Add a hook to allow
setting these addresses so that we can program them back by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After initialising, report the MAC address that we're using for
each port.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We assign nds[i] to a local variable 'dev', which we never use
afterwards. Use the local variable instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Even after an interface has gone !netif_running(), we still want to
catch the 'carrier went down' event for our internal bookkeeping.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sky2 driver introduced netif_rx_schedule_test(). This is
exactly what we need, so remove our local version of this function
(which was called netif_rx_schedule_prep_notup) and use the generic
one instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make caleb.c and pm3386.c include their own header files, to catch
incorrect prototype definitions.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove a number of unnecessary udelay() calls.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not register our netdevices with the kernel until we've actually
finished setting up the hardware and microcode.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes graceful stop timeout handling in PPC4xx EMAC driver.
Currently, when we stop TX/RX channels we just do some number of loops
without relying on actual spent time. This has finally bitten me on
one of our systems (heavy network traffic during start up, RX channel
is stopped several times to configure multicast list).
Graceful channel stop can take up to 1 frame time, so I've added
device specific timeout counter which depends on current link speed
and calls to udelay() to really wait required amount of time before
giving up.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove device specific proc interface. It doesn't handle
renames correctly; it ain't worth fixing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Shrink size of per device data by removing redundant fields
or things that are only used at boot up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allow control of checksumming parameters via ethtool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Avoid possible confusion between skge and sk98lin driver by
tagging messages properly.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add permanent address and link status support via ethtool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove code from sk98lin that does it's own checksum validation.
This code is incorrect when dealing with nested protocols like
VLAN's, and it is better to use regular receive code path to
handle hardware checksum.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update version number and print version in boot message.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Switch to using pci_register_driver as per current convention.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eliminate special case tuning for PCI-Express. This code
causes receive hangs and doesn't help performance much anyway.
Signed-off-by: Stephen Hemminger <shemmnger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sometimes on dual port cards, one tx complete may cover both
ports. To handle that rearrange poll routine to lookup at
end.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Avoid possible race conditions when doing MTU and change and shutdown.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I didn't like the name netif_rx_schedule_test(), in earlier patches
and changed to __netif_rx_schedule_prep to be more consistent.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for Yukon-EC Ultra chip as implemented in SysKonnect's
driver version 8.26.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changes to receive side processing:
* bigger receive ring
* clean up polling loop
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix issues with pause and flush. This code works on
all chip versions tested.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eliminate special case for EC-A1. The overhead isn't so
great that having config option is worth it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Parse outgoing packets in e1000_transfer_dhcp_info as raw packet even if
protocol bits are set. pump, for instance causes kernel panic on some
systems, if parsed via udp header.
Thanks to Derrell Lipman <Derrell.Lipman@BacklotTech.com> for reporting and
testing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The device has not gone through a whole reset/init sequence until the
device is up. Accessing the mii interface before this point is not
safe.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch fixes a problem plaguing Dell notebooks with built-in b44
ethernet: The driver refuses to transmit packets of any kind until after
the first 5-second tx_timeout occurs. This bug causes DHCP negotiation to
fail (timeout) during installation of Ubuntu Linux.
Signed-off-by: Mark Lord <lkml@rtr.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/dgrs.c: In function `dgrs_init_module':
drivers/net/dgrs.c:1598: `dgrs_pci_driver' undeclared (first use in this function)
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In e1000_free_desc_rings, zero-out pointers after the memory they
point to is freed. The test rings are static and get re-used, and
failures during subsequent test setups can cause e1000_free_desc_rings
to get called with dirty pointers. Dirty pointers can cause oopses
or crashes...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In e1000_loopback_test, make sure to call e1000_free_desc_rings if
e1000_setup_loopback_test fails. Currently in that case it will not
get called, causing a leak.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2100: Fix 'Driver using old /proc/net/wireless...' message
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
A prior instance of this patch resolved the issue for the ipw2200.
This one fixes it for the ipw2100.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change CONFIG_FEC_8XX to depend on CONFIG_8xx instead of CONFIG_FEC.
CONFIG_FEC depends on ColdFire CPUs, which does not apply for the
PPC 8xx processors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way the hardware and firmware work is that there is one shared RX
queue and IRQ for a number of different network interfaces. Due to this,
we would like to process received packets for every interface in the same
NAPI poll handler, so we need a pseudo-device to schedule polling on.
What the driver currently does is that it always schedules polling for
the first network interface in the list, and processes packets for every
interface in the poll handler for that first interface -- however, this
scheme breaks down if the first network interface happens to not be up,
since netif_rx_schedule_prep() checks netif_running().
sky2 apparently has the same issue, and Stephen Hemminger suggested a
way to work around this: create a variant of netif_rx_schedule_prep()
that does not check netif_running(). I implemented this locally and
called it netif_rx_schedule_prep_notup(), and it seems to work well,
but it's something that probably not everyone would be happy with.
The ixp2000 is an ARM CPU with a high-speed network interface in the
CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.)
The CPU package also contains 8 or 16 (again depending on the IXP
model) 'microengines', which are somewhat primitive but very fast
and efficient processor cores which can be used to offload various
things from the main CPU.
This driver makes the high-speed network interface in the CPU visible
and usable as a regular linux network device. Currently, it only
supports the Radisys ENP2611 IXP board, but adding support for other
board types should be fairly easy.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This seems to have gotten lost, so I'll resend.
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Added sysfs support to gianfar for modifying FIFO and stashing parameters
* Updated driver to support 10 Mbit, full duplex operation
* Improved comments throughout
* Cleaned up and optimized offloading code
* Fixed a bug where rx buffers were being improperly mapped and unmapped
* (only manifested if cache-coherency was off)
* Added support for using the eTSEC exact-match MAC registers
* Bumped the version to 1.3
* Added support for distinguishing between reduced 100 and 10 Mbit modes
* Modified default coalescing values to lower latency
* Added documentation
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hermas_bap_pread, hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.
Thanks to LinuxICC (http://linuxicc.sf.net)
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In isl_38xx.c
In routine isl38xx_trigger-device
Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the UFO support in S2io driver. This patch uses the UFO
interface available in linux-2.6.15 kernel.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.
This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called. This isn't always so, especially if
we have a link change event during PHY configuration.
This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status. In turn, this causes us to spin with a
permanently asserted IRQ.
The patch ensures that smc_phy_configure always exits with register
bank 2 selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.
While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).
Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--
The function ipw_request_direct_scan() should bail out when the device
is down. This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.
Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The capabilities of the 8169 can be disabled but it is hardly a reason
to prevent the use the device. The (so far) unusual behavior has been
reported on a MIPS platform by Yoichi Yuasa.
Spotted-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I keep on getting "printk: N messages suppressed" messages. We need to test
netif_msg_intr() _before_ running printk_ratelimit(), because the latter
updates state.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I wanted to remove the #include "hostap_ioctl.c" from hostap.c and
build hostap_ioctl.c separately, but this doesn't work since hostap.c
has the same name as the module.
After renaming hostap.c this will be possible.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading this driver I noticed some trailing whitespaces and tabs so I
removed them with some 80th column fitting and a few more similar
things.
Signed-off-by: Carlo Perassi <carlo@linux.it>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"grep "lmc_prot\." -r ." didn't show anything.
lmc_proto.h seems to have the correct prototypes, and is actually used.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Making SkPciWriteCfgDWord a static inline produces a warning due to a
forward declaration in skdrv2nd.h. This patch removes that declaration.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No external user and that small - such a function should be static
inline and not a global function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we are currently unable to fix the problem with carrier and protocol
state signaling in net core I've to disable netif_carrier_off()
calls used by WAN protocol drivers. The attached patch should make
them working again.
The remaining netif_carrier_*() calls in hdlc_fr.c are fine as they
don't touch the physical device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bonding source files still have changelogs in the comments. This, then,
is an update to that changelog.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minor spelling and whitespace corrections.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the version number for the bonding module. Since we've just
added a significant new feature (sysfs support), bump the major number.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This large patch adds sysfs functionality to the channel bonding module.
Bonds can be added, removed, and reconfigured at runtime without having
to reload the module. Multiple bonds with different configurations are
easily configured, and ifenslave is no longer required to configure bonds.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the /proc files show which ARP targets are in use by each bond.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the sysfs interface, the user can remove entries from the ARP table
at runtime. The ARP monitor code now allows for empty entries in the
table.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs interface can create bonds at runtime, and __init code goes away
after module init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs interface can create bonds at runtime, so we need a separate
function to do this, instead of just doing it in the module init code.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs code needs access these functions, so make them
not static, and move the protos to the header file.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs code needs to know what these structs look like, so make them
not static, and move the definition to the header.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitly clear RLB flag during ALB init. This is needed for sysfs
support, since the bond mode can be changed at runtime via sysfs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move memory allocations out of the spinlock during ALB init. This gets
rid of a sleeping-inside-spinlock warning and accompanying stack dump.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take the primary slave name shown in /proc from the actual slave dev
instead of from the command-line parameter, which won't be present
if the bond is created via sysfs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds information about the recently-added transmit policy setting to each
bond's /proc file.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand and correct the parameter descriptions shown by modinfo.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
