We should use the first word of the clear interrupt register if
the bit we're after is < 32, not < 31.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we allocate a bunch of doorbell records and then free them, we'll
end up with completely empty pages, which we then free. However, when
we come back to allocate more doorbell pages, we have to reallocate
those empty pages rather than always trying to take a slot that we've
never used. If we don't, we eventually use up every slot and fail to
allocate a doorbell record, even though we have plenty of free space.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Christian Zoz reported there are multiple NinjaATA devices all sharing the
second product ID string, but not the first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Adds better support for the CB-710, CB-712, CB-720 and CB-722 bridges from EnE
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
TCIC depends on ISA. It is used with ISA-bus system only.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pci_set_power_state is not needed, as we call pci_enable_device() somewhere
else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted
to bus-centric view first.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In interrupt probing (both ISA and PCI) the bridge control register is used
to change interrupt routing to ISA or PCI by changing bit 7. But this bit
only controls the routing of card functional interrupts, not the CSC
interrupts which are used for interrupt probing.
A bad side effect of messing with this register in yenta_probe_irq() is
that it can lead to irq storms if a card is inserted and already powered by
the BIOS.
Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Brown paperbag bug: sas_rphy_delete was ordered completely
wrong. Fix it up to be the same order as sas_phy_delete or
fc_rport_terminate and fix rphy objects that leaked after module
removal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Ben Dooks
Fix the following warnings produced from
drivers/char/s3c2410.c.
drivers/serial/s3c2410.c:757: warning: 'clk' may be used uninitialized
drivers/serial/s3c2410.c:756: warning: 'clksrc' may be used uninitialized
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The wwitch bitmap was added to input_device_id structure and we should
check it when matching handlers and input devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we are compiling with -fno-strict-aliasing (this is the
kernel default), we can drop the following kludge for
iwe_stream_add_event().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for WE-19 to the HostAP driver. One of
the major change is the use of an explicit flag to tell if iwstat is
in dBm or not.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_pci and hostap_plx drivers still use PCI driver names
"prism2_pci" and "prism2_plx" respectively. This is unfriendly to
linux-wlan-ng, which uses the same names. So, if e.g. hostap_pci and
prism2_pci are loaded, they will "share" /sys/bus/pci/drivers/prism2_plx
directory.
Change PCI driver names of hostap_pci and hostap_plx to be equal to
their module names.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I found an inconsistent spin_lock usage in ipmi_smi_msg_received.
Signed-off-by: Hironobu Ishii <hishii@soft.fujitsu.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix this:
drivers/video/aty/xlinit.c: In function `atyfb_xl_init':
drivers/video/aty/xlinit.c:256: warning: ISO C90 forbids mixed declarations and code
- repair some kooky coding style
- Use ARRAY_SIZE()
Cc: Tom 'spot' Callaway <tcallawa@redhat.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
usb_unlink_urb is always async now, so URB_ASYNC_UNLINK was removed from
core USB and we must do as well.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().
The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
otherwise hangs Acer TM81xx machines as reported.
Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While this is true, E8390_CMD is zero on i386, and thus there should be no
effect for these machines. Machines like Mac, Amiga etc. which use Alan's
clever register mapping may have a non-zero E8390_CMD and result in bogus
"transmitter busy" type messages from this bug.
Fixes BUG# 3991.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Read only needed data in __orinoco_ev_txexc().
Don't read the 802.11 header beyond addr1. The rest of the frame is not
used currently.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Annotate endianess of variables and structure members.
Don't reuse variables for both host-endian and little-endian data.
Minor comment changes in affected structures.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove unneeded forward declarations.
Also reorder struct pcmcia_driver initialization to keep attach and
detach together.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
orinoco_send_wevents() could return without unlocking.
Failure to read BSSID from the hardware would cause orinoco_send_wevents() to
return with lock held. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Fix memory leak and unneeded unlock in orinoco_join_ap()
If orinoco_lock() fails, the code would still run orinoco_unlock(),
instead of freeing the allocated memory. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove inneeded system includes.
Most system includes are not needed. In particular, the hardware
backends don't need anything network related. Some includes have been
moved from local headers to the C files where they are actually used.
Includes that have to be in the local headers are no longer from the C
sources.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The PowerMac mesh SCSI driver had some missing error handling which would
trigger warnings due to lack of handling of return value from
scsi_add_host. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SMU is the "system controller" chip used by Apple recent G5 machines
including the iMac G5. It drives things like fans, i2c busses, real time
clock, etc...
The current kernel contains a very crude driver that doesn't do much more
than reading the real time clock synchronously. This is a completely
rewritten driver that provides interrupt based command queuing, a userland
interface, and an i2c/smbus driver for accessing the devices hanging off
the SMU i2c busses like temperature sensors. This driver is a basic block
for upcoming work on thermal control for those machines, among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Handle dmi_system_check() elegantly, now that my bugfix is upstream.
- Add support for the X41 and R52.
- Cleanup some comments do I do not have to keep updating them with each
new whitelisted laptop.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The address passed to io_remap_pfn_range() in hpet_mmap() does not need to
be converted using __pa(): it is already a physical address. This bug was
found and the patch suggested by Clay Harris.
I introduced this particular bug when making io_remap_pfn_range changes a
few months ago. In fact mmap()ing /dev/hpet has *never* previously worked:
before my changes __pa() was being executed on an ioremap()ed virtual
address, which is also invalid.
Signed-off-by: Keir Fraser <keir@xensource.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix namespace clash:
drivers/mtd/devices/docecc.c:43:1: warning: "DEBUG" redefined
In file included from drivers/mtd/devices/docecc.c:40:
include/linux/mtd/mtd.h:219:1: warning: this is the location of the previous definition
Signed-off-by: Grant Coady <gcoady@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename the (apparently) bttv intern #define vprintk to verbprintk to
resolve a name clash.
Reason: vprintk() is defined in include/linux/kernel.h similar to printk
but with a va_list argument.
(akpm: I changed it to bttv_printk)
Cc: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This code appears to be more trouble than it's worth, considering that
no normal users reload drivers. So, we comment it for now. It is not
removed outright for the benefit of hackers (that is, myself).
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB: Add device id's for Novatel Wireless CDMA wireless PC card.
The Novatel CDMA card behaves the same as the AirPrime by providing
a USB serial port.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The card sometimes sends >2000 bytes in one single chunk. Ouch.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Addresses some small bugs in the pegasus ethernet-over-USB driver.
Specifically, malformed long packets from the adapter could cause a kernel
panic; the interrupt interval calculation was inappropriate for high-speed
devices; the return code from read_mii_word was tested incorrectly; and
failure to unlink outstanding URBs before freeing them could lead to kernel
panics when unloading the driver.
Signed-off-by: Kevin Vigor <kevin@realmsys.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Three minor sl811-hcd fixes:
- Elminate memory leak on one (rare) disable/shutdown path.
- For periodic transfers that don't need to be scheduled, update
urb->start_frame to represent the transfer phase correctly.
- Report the (single) port as removable, by default.
Since no drivers yet use start_frame or that part of the hub descriptor,
only that leak is likely to ever matter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/host/sl811-hcd.c | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
This patch fixes several types in the PXA25x udc driver and hence fixes
several compiler warnings.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm using a 2 port USB RS232 dongle to connect to a serial-IR cradle for
a bar code reader). Detecting the baudrate of the serial-IR involves
keeping DTR low while changing baudrate.
This works using normal 16550A serial ports as well as the FTDI driver
version 1.4.0 (Linux 2.6.8) but stopped working with the change to
"ensure RTS and DTR are raised when changing baudrate" introduced in
version 1.4.1 (Linux 2.6.9).
The attached patch fixes this, so RTS and DTR is only raised when
changing baudrate iff the previous baudrate was B0.
Signed-off-by: Peter Favrholdt <pfavr@how.dk>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support for HUAWEI E600 and Audiovox AirCard
User reports say that these devices work without driver modification.
Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a few problems with ub and cleans up a couple of things:
- Bump UB_MAX_REQ_SG, this allows to burn CDs
- Drop initialization of urb.transfer_flags,
now that URB_UNLINK_ASYNC is gone
- Add forgotten processing of stalls at GetMaxLUN
- Remove a few more P3-tagged printks whose time has come
- Correct comment about ZIP-100
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/block/ub.c | 53 +++++++++++++++++++++++++++--------------------------
1 file changed, 27 insertions(+), 26 deletions(-)
This function expects an unsigned 32-bit type as its third argument:
static u32 pci_size(u32 base, u32 maxbase, u32 mask)
However, given these definitions:
#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
these two calls in drivers/pci/probe.c are problematic for architectures
for which a UL is not equivalent to a u32:
sz = pci_size(l, sz, PCI_BASE_ADDRESS_MEM_MASK);
sz = pci_size(l, sz, PCI_ROM_ADDRESS_MASK);
Hence the below compile warning when building for ARCH=ppc64:
drivers/pci/probe.c: In function `pci_read_bases':
/.../probe.c:168: warning: large integer implicitly truncated to unsigned type
/.../probe.c:218: warning: large integer implicitly truncated to unsigned type
Here is a simple fix.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The class symlinks in sysfs don't properly handle changing device names.
To demonstrate, rename your network device from eth0 to eth1. Your
pci (or usb, or whatever) device will still have a 'net:eth0' link,
except now it points to /sys/class/net/eth1.
The attached patch makes sure the class symlink name changes when
the class device name changes. It isn't 100% correct, it should be
using sysfs_rename_link. Unfortunately, sysfs_rename_link doesn't exist.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add the helper and use it instead of open coding the klist_node_attached() check
(which is a layering violation IMHO)
idea by Alan Stern.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bus_rescan_devices_helper() does not hold the dev->sem when it checks for
!dev->driver(). device_attach() holds the sem, but calls again
device_bind_driver() even when dev->driver is set.
What happens is that a first device_attach() call (module insertion time)
is on the way binding the device to a driver. Another thread calls
bus_rescan_devices(). Now when bus_rescan_devices_helper() checks for
dev->driver it is still NULL 'cos the the prior device_attach() is not yet
finished. But as soon as the first one releases the dev->sem the second
device_attach() tries to rebind the already bound device again.
device_bind_driver() does this blindly which leads to a corrupt
driver->klist_devices list (the device links itself, the head points to the
device). Later a call to device_release_driver() sets dev->driver to NULL
and breaks the link it has to itself on knode_driver. Rmmoding the driver
later calls driver_detach() which leads to an endless loop 'cos the list
head in klist_devices still points to the device. And since dev->driver is
NULL it's stuck with the same device forever. Boom. And rmmod hangs.
Very easy to reproduce with new-style pcmcia and a 16bit card. Just loop
modprobe <pcmcia-modules> ;cardctl eject; rmmod <card driver, pcmcia
modules>.
Easiest fix is to check if the device is already bound to a driver in
device_bind_driver(). This avoids the double binding.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent forcedeth nics support checksum offloading for tx.
The attached patch, written by Ayaz Abdulla, adds the support to the
driver.
It also cleans up the handling of the three dma ring entry formats that
are supported by the driver.
Signed-off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-By: Jeff Garzik <jgarzik@pobox.com>
tree 8c1676c8a15c08e6d4c718fc7cd42d9bf4cd8235
parent 0ccc3dd6469ed492578c184f47dde2baccde3593
author James Ketrenos <jketreno@linux.intel.com> 1126715240 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316717 -0500
Updated hostap to be compatible with extra_prefix_len changes.
Accomplished via:
for i in hostap_ap.c hostap_80211_tx.c; do
sed -i -e "s:\([.>]\)extra_prefix_len:\1extra_mpdu_prefix_len:g" \
-e "s:\([.>]\)extra_postfix_len:\1extra_mpdu_postfix_len:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8ec97d9056ceaf0f845ed51175dd842b700baadd
parent 329128457008ace3110c96971addf85a767dd5af
author James Ketrenos <jketreno@linux.intel.com> 1126714484 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316636 -0500
Updated hostap to be compatible with ieee80211_hdr changes.
Change accomplished via:
for i in hostap_ap.{c,h} hostap_80211_{t,r}x.c; do
sed -i -e "s:ieee80211_hdr\([^_]\):ieee80211_hdr_4addr\1:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 713b6ff3311decfe42d5209f7b2508736d144b85
parent 6465beff0e89779330450dffc2a5e6dc5154eebf
author James Ketrenos <jketreno@linux.intel.com> 1126716726 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316162 -0500
Updated ipw2200 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 9f86c7b4f59249c05c96c360dfaa817995e8a44f
parent 9b09701b2c6254f2fddb009004a14eb5a908714f
author James Ketrenos <jketreno@linux.intel.com> 1126714305 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316074 -0500
Updated ipw2200 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree ee48cbe413b795d6be454b9baf4f3bd3d74814cb
parent 49856b147763bd6847e0d8f53aee1ddd61385638
author James Ketrenos <jketreno@linux.intel.com> 1126716634 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316024 -0500
Updated ipw2100 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 992b203395c50342f1cced415acae6177344e270
parent c59bb604a2ff4e40232ff0422e7adc44e3b007a0
author James Ketrenos <jketreno@linux.intel.com> 1126714006 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127315910 -0500
Updated ipw2100 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
vlan_hwaccel_rx should be used when in interrupt context.
Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=5284
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup receive buffer allocation and management,
Add more error handling checks from PHY and bump version.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Expand the returned data for ethtool debug access to include
all of the mapped PCI area; except for the small set of registers
that are for diagnostic RAM access. Access to those registers
will hang the system.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix bond_enslave link monitoring warning to check use_carrier status
and ethtool_ops in addition to do_ioctl. This version checks ethtool_ops
as well as do_ioctl, and also uses the per-bond params.use_carrier
instead of the global use_carrier.
Signed-off-by: Jason R. Martin <nsxfreddy@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Based on simplification idea from Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up code by using enums instead of hard-coded magic numbers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We currently unregister the config-osm driver if initialization of the
legacy ioctl() handlers failed but still return success. We should be
returning -EBUSY in this case.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This function was removed a while ago, but crept in again via a recent
scsi merge.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the problem Bjorn reported. The busy_initializing flag
should have cleared before going into the for loop.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In fbdev perspective, the frontporch is the lower/right margin and the
backporch is the upper/left margin.
Correct.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change in nvidiafb caused nvidiafb_cursor to always return -ENXIO
instead of using the soft_cursor. This will happen if the parameter "hwcur"
is not set, which happens to be the default.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ipoib_mcast_restart_task() is always called from within the
single-threaded IPoIB workqueue, so flushing the workqueue from within
the function can lead to a recursion overflow. But since we're
running in a single-threaded workqueue, we're already synchronized
against other items in the workqueue, so just get rid of the flush in
ipoib_mcast_restart_task().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following commit breaks cisco mode with my WAN drivers:
author David S. Miller <davem@davemloft.net>
Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700)
commit 689be43945
"[NET]: Remove gratuitous use of skb->tail in network drivers."
The following patch fixes it - please apply (cisco_hard_header does
skb_push(4 bytes)).
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to subtract off the header length from our payload
length when sending multi-packet SA messages.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
this patch adds some fc host attributes and removes its equivalents
from the zfcp_adapter structure and zfcp specific sysfs subtree.
Furthermore it removes superfluous calls to fc_remort_port_delete when
an adapter is set offline because rports will be removed by
fc_remove_host anyway.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
N_Port ID Virtualization (NPIV) allows a single FCP port to appear as
multiple, distinct ports providing separate port identification. NPIV
is supported by FC HBAs on System z9. zfcp was adapted to support this
new feature.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debug features (DBFs) els_dbf, cmd_dbf and abt_dbf were removed and
san_dbf, hba_dbf and scsi_dbf were introduced. The erp_dbf did not
change.
The new traces improve debugging of problems with zfcp, scsi-stack,
multipath and hardware in the SAN. san_dbf traces things like ELS and
CT commands, hba_dbf saves HBA specific information of requests, and
scsi_dbf saves FCP and SCSI specific information of requests. Common
to all new DBFs is that they provide a so called structured view. This
significantly improves readability of the traces.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o union zfcp_req_data removed
o increment unit refcount when processing FCP commands
(This fixes a theoretical race: When all scsi commands of a unit
are aborted and the scsi_device is removed then the unit could be
removed before all fsf_requests of that unit are completely processed.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o always use locking when changing erp_action lists,
o avoid escalation to ERP_ACTION_REOPEN_PORT_FORCED if erp_action is
still in use for ERP_ACTION_REOPEN_PORT
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thursday, September 15, 2005 6:22 AM, Christoph Hellwig wrote:
> Looks good to me, except for the spurious scsi_print_command prototype
> in mptscsih.h.
The attached patch addresses that concern.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Summary of Changes:
* splitting mpt_interrupt per Christophs suggestion
about a month ago
* rename ScsiCfgData to SpiCfgData structure,
then move all the raid related info into
new structure called RaidCfgData. This is
done because SAS supports RAID, as well as SPI,
so the raid stuff should be seperate.
* incorrect timeout calculation for cntdn
inside WaitForDoorbellAck and WaitForDoortbellInt
* add support for interpreting SAS Log Info
* Increase Event Log Size from 0xA to 0x32
* Fix bug in mptsas/mptfc/mptspi - when controller
has Initiator Mode Disabled, and only running in
TargetMode, the mptctl would panic when loading.
The fix is to return 0, instead of -ENODEV, in
SCSI LLD respective probe routines
* Fix bug in mptlan.c - driver will panic if
there is host reset, due to dev being set to
zero in mpt_lan_ioc_reset
* Fix's for SPI - Echo Buffer
* Several fix's in mptscsih_io_done - FCP Response
info, RESIDUAL_MISMATCH, Data Underrun, etc.
* Cleanup Error Handling - EH handlers,
mptscsih_flush_cmds, and zeroing out ScsiLookup
from mptscsih_qcmd
* Cleanup asyn event handling from
mptscsih -> mptscsih_event_process. Also
added support for SAS Persistent Table Full,
an asyn event
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds the actual mptsas driver, based upon the LSI driver with new work
for SAS transport class integration from Eric Moore and me.
This obviously depends on the SAS transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- various bits for SAS support from the LSI driver.
- use the device private data for the fusion target private data.
this should be using the midlayer target data framework, but we
can't move over to that until fusion has been switched to the
generic DV code
- use target ID and channel from the fusion target private data,
because those in scsi_device will be different for mptsas
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Userspace SRQs don't have a buffer allocated for them in the kernel, so
it doesn't make sense to set srq->last during initialization. In fact,
this can crash trying to follow a nonexistent buffer pointer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From: Alan Stern <stern@rowland.harvard.edu>
This patch (as561) fixes the error handler's thread-exit code. The
kthread_stop call won't wake the thread from a down_interruptible, so
the patch gets rid of the semaphore and simply does
set_current_state(TASK_INTERRUPTIBLE);
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Modified to simplify the termination loop and correct the sleep condition.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We fix the oops by enforcing the host state model. There have also
been two extra states added: SHOST_CANCEL_RECOVERY and
SHOST_DEL_RECOVERY so we can take the model through host removal while
the recovery thread is active.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The error handling paths in mthca_tavor_post_srq_recv() and
mthca_arbel_post_srq_recv() are quite bogus, the result of a
screwed up merge. Fix them so they work as intended.
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_create_eq(), we call get_eqe() before setting eq->nent. This
is wrong, because get_eqe() uses eq->nent. Fix this, and clean up the
code a little while we're at it. (We got lucky with the current code,
because eq->nent was cleared to 0, which get_eqe() made happen to do
the right thing)
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We got a little mixed up with what the backoff member holds in the
IPoIB multicast group structure: sometimes it was used as a number of
seconds, and sometimes it was used as a number of jiffies. Fix the
code so that backoff is always in seconds.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting first WQE for mem-free HCAs: we need to link to previous
WQE even in that case. While we're at it, simplify code for
Tavor-mode HCAs. We don't really need the conditional test there
either; we can similarly always link to the previous WQE.
Based on Michael S. Tsirkin's analogous fix for userspace libmthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware reads the ACK timeout field from the most significant 5
bits of struct mthca_qp_path's ackto field, not the least significant
bits. This fix has the driver put the timeout in the right place.
Without this, we get a timeout that is 2^8 times too small.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since ipoib uses queue_delayed_work to run flush task on port state events,
it must flush scheduled work after unregistering the event handler.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch (as545) fixes the list traversals in __scsi_remove_target and
scsi_forget_host. In each case the existing code list_for_each_entry_safe
in an _unsafe_ manner, because the list was not protected from outside
modification while the iteration was running.
The new scsi_forget_host routine takes the moderately controversial step
of iterating over devices for removal rather than iterating over targets.
This makes more sense to me because the current scheme treats targets as
second-class citizens, created and removed on demand, rather than as
objects corresponding to actual hardware. (Also I couldn't figure out any
safe way to iterate over the target list, since it's not so easy to tell
when a target has already been removed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Florin Malita <fmalita@gmail.com>
bond_init() is not releasing rtnl_sem after register_netdevice() and before
calling unregister_netdevice() (from bond_free_all()) in the exception
path. As the device registration is not completed (dev->reg_state ==
NETREG_REGISTERING), the call to unregister_netdevice() triggers
BUG_ON(dev->reg_state != NETREG_REGISTERED).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old driver was not fully adapted to new USB ABI and does not
work.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found one other thing that needs to be fixed. The call to
scsi_release_buffers in scsi_unprep_request causes an oops, because the
sgtable has already been freed in scsi_io_completion. The following patch
is needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed
using pci_bus_{read,write}_config_dword(). A recent audit of drivers/
turned up several cases of byte- and word-sized accesses. The harmful
ones were fixed by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When doing ioctl HDIO_DRIVE_TASKFILE, the ide_task_t's request pointer is
never set, but flagged_taskfile and do_rw_taskfile pass it as a parameter
to the prehandler. The kernel will oops taskfile pio-out commands because
of this (taskfile pio-in doesn't use a prehandler). This fix sets the
request pointer at the time the request is created to stop this oops.
Signed-off-by: Timothy Thelin <timothy.thelin@wdc.com>
Cc: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's the patch from
http://bugzilla.kernel.org/show_bug.cgi?id=4853
It is a feeble attempt at fixing the request handling in pf, it is totally
foobar right now.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove the relative input device
- Add an absolute input device
- Misc. cleanup and bug fixing
The patch is sizable due to the cleanup from removing the relative input
device (net -112 lines).
Signed-off-by: Robert Love <rml@novell.com>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BUG fixes:
The driver used to allocate memory with spinlock held which has been
fixed in this patch.
The driver was printing the entire buffer when it received a invalid
entry in image_type. The fix is to only print a warning message and not
the buffer.
Usability enhancements:
It is possible that due to user error the /sys/class/firmware/dell_rbu
entries might be missing, this can happen if the user does the following
echo 1 > /sys/class/firmware/dell_rbu/loading
echo 0 > /sys/class/firmware/dell_rbu/loading
This will make the entries in /sys/class/firmware/ to disappear and the
only way get them back was bby unloading and loading the driver.
This patch makes the user recreate these entries by echoing init in to
image_type.
This patch has been tested with Libsmbios and Dell OpenManage.
Signed-off-by: Abhay Salunke <Abhay_Salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add WRITE_LONG_2 as write safe commands, which which allows normal users to
make a c1-, c2- and cu-scan (so called cxscan) with readcd on
cxscan-capable cd/dvd-writers
Signed-off-by: Jens Axboe <axboe@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Got confused with the crypto update. The last patch added a call to
destroy_workqueue() for a non-existent workqueue with the comment "Remove
device workqueue on module unload". This is nonsense. Remove the offending
hunk again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Calculate correct size for bl_dev array. It should be 8KB instead of 512KB
for 2^16 bits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add partition definitions for the new Sharp Zaurus models Spitz (SL-C3000),
Akita (SL-C1000) and Borzoi (SL-C3100)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This hunk from the sharpsl/corgi backlight update appears to have got lost
somewhere along the way. Its needed to match the other changes.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a signedness bug with RAID6 for Altivec, and makes the
Altivec code testable in userspace.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix and simplify the workaround code for the 4GB boundary tx buffer
hardware bug.
1. Need to unmap the original SKB's dma addresses if a new SKB cannot
be allocated.
2. Need to pass the base flag to tigon3_4gb_hwbug_workaround() or TSO
won't work properly.
3. The guilty entry and length parameters for
tigon3_4gb_hwbug_workaround() are removed as they are not necessary.
4. Remove assumption that only one fragment can hit the 4GB boundary.
Another fragment can hit 8GB for example.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 0 to NULL where appropriate.
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[originally sent to Alan, he had no problems with it]
- iomem pointers marked as such
- several direct dereferencings of such pointers replaced with read[bw]().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes some compilation warnings, mostly
trivially. acpi.c fix also noted by Kenji Kaneshige.
Signed-off-by; Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make sure we that completion is the final action we take; prior to this
change, another CPU may have changed ap->pio_task_state before we tested
it a final time.
Spotted by, and original patch by Albert Lee @ IBM.
Also includes a minor optimization: eliminate a ton of unnecessary
queue_work() calls, simply by jumping to the beginning of the FSM
function ata_pio_task().
This patch makes the driver work with any BladeCenter
network switch, it used to work only with certain
models.
Please apply.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
author James Ketrenos <jketreno@linux.intel.com> 1126713327 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1126713327 -0500
Updated ipw2200 to compile with ieee80211 abg_ture to abg_true change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 01:07:47 2005 -0400
Update PCMCIA ID's.
Intel Pro/Wireless 2011 and 2011B have the same numeric ID, so use
strings instead.
Take all entries from *.conf for Orinoco, HostAP and linux-wlan-ng and
adds them with minimal changes (e.g. we don't need a revision string
after a string that identifies the chipset).
Add comments with card names to all numeric entries. Note: the comments
don't and cannot cover all cards, since the main reason of having
numeric IDs is to cover cards that are often rebranded.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 00:49:05 2005 -0400
Remove conditionals that are useless in the kernel drivers.
Kernel drivers are never compiled against pcmcia-cs headers.
Firmware is never embedded into spectrum_cs module.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't crash if ethtool statistics are requested and device is down.
Fix is to allocate pci space for statistics only when needed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Bonding leaks route structures when the ARP monitor is
configured to send probes over VLANs.
Originally reported by Ian Abel <ian.abel@mxtelecom.com>; his
original fix was modified by Jay Vosburgh to correct coding style and to
close a leak it missed.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don Fry reminded me that the pcnet32_loopback_test() asssumes the ring size
is no less than 4. The minimum ring size was changed to 4 in
pcnet32_set_ringparam() to allow the loopback test to work unchanged.
- Set minimum ring size to 4 to allow loopback test to work unchanged
- Moved variable init_block to first field in struct pcnet32_private
Signed-off-by: Hubert WS Lin <wslin@tw.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the set_ringparam(), one of the ethtool operations,
which allows changing tx/rx ring sizes via ethtool.
- Changed memery allocation of tx/rx ring from static to dynamic
- Implemented set_ringparam()
- Tested on i386 and ppc64
Signed-off-by: Hubert WS Lin <wslin@tw.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In the unlikely case of the new screen width much wider then the old,
use (old_row_size * new_rows) instead of new_screen_size to prevent a
buffer overrun during the copy.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: walt <wa1ter@myrealbox.com>
"I routinely switch the console font during bootup to
8x8 so I can get 50 lines per screen. Until 09 Sept,
just changing to the small font automatically gave me
all 50 lines -- but now I'm only getting 25 lines even
with the small font. The bottom half of the screen
displays the text that already scrolled off the top."
This bug is due to an erroneous check in the recently added hook,
vgacon_resize(). It checks the new height against the original number of
rows of the console. Because the original number of rows depends on both
the scanline and the font height, check it instead against the
scanline/fontheight.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The Twister chipsets are actually prosavages. Reclassify them as
such and remove the S3_SAVAGE_TWISTER id.
- Fix i2c code if fb_firmware_edid() returns NULL
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Alan Cox <alan@redhat.com>
The virt_to_bus() wasn't correctly taken out of this driver. It needs
to be able to track both physical and virtual addresses for its prd table.
Update the driver to do this with separate tracking entries.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Vincent Sanders
When building the ARM platforms several serial drivers fail to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Its possible that we can write to the hvc_console tty as soon it is
registered. Recently this started happening due to (what looks like) a
change to the hotplug code.
Unfortunately at this stage we have not started the khvcd kernel thread and
oops. The solution is to start the kernel thread before registering the
tty.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The call to fb_firmware_edid may return NULL but this is not checked before
trying to memcpy using this pointer.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the 4th id field should be not used
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Wed, 2005-09-14 at 18:06 +1000, Anton Blanchard wrote:
> And in particular it looks like the scsi_unprep_request in
> scsi_queue_insert is causing it. The following patch fixes the boot
> problems on the vscsi machine:
OK, my fault. Your fix is almost correct .. I was going to do this
eventually, honest, because there's no need to unprep and reprep a
command that comes in through scsi_queue_insert().
However, I decided to leave it in to exercise the scsi_unprep_request()
path just to make sure it was working. What's happening, I think, is
that we also use this path for retries. Since we kill and reget the
command each time, the retries decrement is never seen, so we're
retrying forever.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modules need a license to prevent kernel tainting.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes an issue in scsi command initialization from a request
where sd, sr, st, and scsi_lib all fail to copy the request's
cmd_len to the scsi command's cmd_len field.
Signed-off-by: Timothy Thelin <timothy.thelin@wdc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In some cases, especially on modern laptops with a lot of PCI and
cardbus bridges, we're unable to assign correct secondary/subordinate
bus numbers to all cardbus bridges due to BIOS limitations unless
we are using "pci=assign-busses" boot option.
So some cardbus controllers may not have attached subordinate pci_bus
structure, and yenta driver must cope with it - just ignore such cardbus
bridges.
For example, see https://bugzilla.novell.com/show_bug.cgi?id=113778
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Certain (SGI?) ia64 boxes object to having their PCI BARs
restored unless absolutely necessary. This patch restricts calling
pci_restore_bars from pci_set_power_state unless the current state
is PCI_UNKNOWN, the actual (i.e. physical) state of the device is
PCI_D3hot, and the device indicates that it will lose its configuration
when transitioning to PCI_D0.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 4/4] s390: qeth driver fixes .
From: Frank Pavlic <pavlic@de.ibm.com>
- Clear read channel first prior to using ccw_device_set_offline.
- use QETH_DBF_TEXT instead of QETH_DBF_SPRINTF
- invoke qeth_halt_channel and qeth_clear_channel for all channels,
even if halt/clear for one of the channel fails.
- enable qeth_arp_query function for GuestLAN devices
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 2 -
qeth_main.c | 106 +++++++++++++++++++++++++-----------------------------------
qeth_sys.c | 11 +++---
3 files changed, 53 insertions(+), 66 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff,
I'm sorry seems that they have not been sent out either ...
ok here they come ...
[patch 3/4] s390: TSO related fixes in qeth driver
From: Frank Pavlic <pavlic@de.ibm.com>
TSO related fixes :
- changing value of large_send attribute while network traffic
is running caused program check and thus device recovery.
- Due to hardware restriction discard packet when it exceeds 60K
otherwise qeth will cause program checks and thus traffic stall
when trying to send such huge packets.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 4 ++--
qeth_main.c | 33 +++++++++++++++++++++------------
qeth_sys.c | 10 +++-------
3 files changed, 26 insertions(+), 21 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds an "Ethernet" driver which sends Ethernet packets over the standard
RapidIO messaging. This depends on the core RIO patch for mailbox/doorbell
access.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff,
sorry if I have flooded your inbox, I had some problems with the
mail server here yesterday, but it seems to be fixed ...
Ok patch 3-4 have no dependencies on patch 2 since only qeth driver is
affected.Thus I have made a new patch 2 for ctc driver.
Thank you .
[patch 2/4] s390: ctc driver fixes
From: Peter Tiedemann <ptiedem@de.ibm.com>
- race condition fixed
- minor cleanup
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
ctcmain.c | 41 ++++++++++++++++++++++-------------------
1 files changed, 22 insertions(+), 19 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains possible cleanups including the following:
- make needlessly global code static
- #if 0 the following unused global function:
- sdladrv.c: sdla_intde
- remove the following unused global variable:
- lmc_media.c: lmc_t1_cables
- remove the following unneeded EXPORT_SYMBOL's:
- cycx_drv.c: cycx_inten
- sdladrv.c: sdla_inten
- sdladrv.c: sdla_intde
- sdladrv.c: sdla_intack
- sdladrv.c: sdla_intr
- syncppp.c: sppp_input
- syncppp.c: sppp_change_mtu
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace the custom is_digit()/is_hex_digit() macros with
isdigit()/isxdigit() from <linux/ctype.h> Additionaly remove unused macro
is_alpha() from <linux/wanpipe.h>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge of four previous patches and the Kconfig fix
* Remove debug printk's
* whitespace cleanup and version number change
* clear interrupts, reset phy, and reset hardware on shutdown
* ignore 64bit counter overflow interrupts
* fix a couple of places where second port could clobber state
of first port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Use new Wireless Extension API for wireless stats.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for ETHTOOL_GPERMADDR to via-rhine.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for ETHTOOL_GPERMADDR to forcedeth.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not count frames dropped by the hardware as part of rx_dropped.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not count non-error frames dropped by the hardware as
part of rx_dropped. Instead, count those frames dropped as
rx_missed_errors. Also, do not count other error frames as part of
rx_dropped. Finally, do not count oversized frames in rx_dropped
(since they are counted as part of rx_length_errors).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not count frames dropped by the hardware as part of rx_dropped.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
this patch display the correct channel number with iwlist scan
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes a nasty typo I introduced in my previous patch (commit
f2c853bca5). The right offset of the
second port in pure sata mode is 64 and not 0x64.
Thanks to Martin Schuster for pointing this to me
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
---
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
xircom_cb.c does #if CONFIG_NET_POLL_CONTROLLER instead of #ifdef,
resulting in drivers/net/tulip/xircom_cb.c:120:5: warning:
"CONFIG_NET_POLL_CONTROLLER" is not defined.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/s2io.c: In function `init_shared_mem':
drivers/net/s2io.c:431: warning: cast from pointer to integer of different size
drivers/net/s2io.c: In function `free_shared_mem':
drivers/net/s2io.c:662: warning: cast from pointer to integer of different size
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix PCI device id issues with sk98lin driver.
1. DLINK 530-T card has no Vital Product Data (VPD) area so the sk98lin
driver won't work. (skge does however)
2. Remove commented out Yukon2 stuff
3. Restrict Linksys card to revisions that don't conflict with r8169 version.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The timer/watchdog register definitions were missing from
the mpcore watchdog patch. Add them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves aic7xxx over to the dma_get_required_mask() API and
dumps its open coded memory check.
It also appears from this bug:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=167049
That 39 bit addressing doesn't work on older cards. I surmise that the
AHC_LARGE_SCBS flag is the one that marks cards capable of using 39 bit
addressing, so I also folded that check into the code.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some adjustments to the matroxfb code, for one part preventing the display
to be disabled for longer than necessary, and for the other part to make
information about the frame buffer position available so that a kernel
debugger might obtain that before the initial mode change.
Finally, some return code corrections to fit the generic fb code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
const-ify the font control structures and data, to make somewhat better
guarantees that these are not modified anywhere in the kernel.
Specifically for a kernel debugger to share this information from the
normal kernel code, such a guarantee seems rather desirable.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An adjustment to the SM_DOWN case of fbcon_scroll to match the behavior of
SM_UP.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a input driver for the keyboard found on the Zaurus Cxx00 series (Spitz,
Akita, Borzoi). Its based on corgikbd but there are enough subtle differences
to justify a separate driver.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
backlight driver. Abstract model/machine specific functions to corgi_lcd.c
via sharpsl.h
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver. Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource. Move a
function prototype into the w100fb header file where it belongs.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some redundant BUG_ON() statements in pktcdvd and move one run-time
check to compile-time.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use kcalloc and kzalloc in pktcdvd.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the /proc statistics, only count writes that upper layers have requested.
Don't count additional writes created inside the packet driver to satisfy the
requirement to only write full packets.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the "theory of operation" description.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the packet writing driver, if the drive reports a packet size larger than
the driver can handle, bail out safely instead of triggering a BUG_ON.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add SCSI host and device info not elsewhere available to /proc/scsi/cciss/*
Namely, connect cciss device instance with scsi host number, and give scsi
host number, bus, target, lun, devicetype, and 8-byte cciss LUNID for each
tapedrive/medium changer attached to a controller
For instance:
# cat /proc/scsi/cciss/2
cciss0: SCSI host: 2
c2b0t0l0 01 0x0000000000000001
Signed-off-by: Stephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for "One Button Disaster Recovery" devices to the
cciss driver. (OBDR devices are tape drives which can pretend to be cd-rom
devices temporarily. Once booted the device can be reverted to a tape drive
and data recovery operations can be automatically begun.)
This is an enhancement request by a vendor/partner working on One Button
Disaster Recovery.
Signed-off-by: Stephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CCISS driver seems to loose track of DMA mappings created by it's
fill_cmd() routine. Neither callers of this routine are extracting the DMA
address created in order to do the unmap.
Instead, they simply try to unmap 0x0. It's easy to see this problem on an
x86_64 system when using the "swiotlb=force" boot option. In this case, the
driver is leaking resources of the swiotlb and not causing a sync of the
bounce buffer.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a bug in cciss_remove_one. A set of braces was missing for
the if statement causing an Oops on driver unload.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the way we complete commands. In the old method when we
got a completion we searched our command list from the top until we find it.
This method uses a tag associated with each command (not SCSI command tagging)
to index us directly to the completed command. This helps performance.
Signed-off-by: Don Brace <dab@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes a couple of functions dealing with configuration and
replaces them with new functions. This implementation fixes some bugs
associated with the ACUXE. It also allows a logical volume to be removed from
the middle without deleting all volumes behind it.
If a user has 5 logical volumes and decides he wants to reconfigure volume
number 3, he can now do that without removing volumes 4 & 5 first. This code
has been tested in our labs against all application software.
Signed-off-by: Chase Maupin <chase.maupin@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a flag called busy_initializing. If there are multiple
controllers in a server AND the HP agents are running it's possible the agents
may try to poll a card that is still initializing if the driver is removed and
then added again.
Signed-off-by: Don Brace <dab@hp.com>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds new PCI and subsystem ID's that finally made the spec. It
also include a name change for one controller. I know there's a lot of
duplicat names but the fw folks wanted this for the different implementations.
Even though the same ASIC is used it may be embedded on some platforms,
standup card in others, and a mezzanine in other servers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove check_region references from comments and printk statements so that
searching for real users of this deprecated function gets easier.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the foot long pile of festering garbage in eighty_ninty_three with
some actual clean code. All the ifdefs are fixed and havent changed since
2.4
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
More visible user information of scheduled feature removal.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
