I noticed in oprofile study a cache miss in tcp_rcv_established() to read
copied_seq.
ffffffff80400a80 <tcp_rcv_established>: /* tcp_rcv_established total: 4034293
2.0400 */
55493 0.0281 :ffffffff80400bc9: mov 0x4c8(%r12),%eax copied_seq
543103 0.2746 :ffffffff80400bd1: cmp 0x3e0(%r12),%eax rcv_nxt
if (tp->copied_seq == tp->rcv_nxt &&
len - tcp_header_len <= tp->ucopy.len) {
In this function, the cache line 0x4c0 -> 0x500 is used only for this
reading 'copied_seq' field.
rcv_wup and copied_seq should be next to rcv_nxt field, to lower number of
active cache lines in hot paths. (tcp_rcv_established(), tcp_poll(), ...)
As you suggested, I changed tcp_create_openreq_child() so that these fields
are changed together, to avoid adding a new store buffer stall.
Patch is 64bit friendly (no new hole because of alignment constraints)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, TCP code uses "sk" for struct sock pointer.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
YeAH-TCP is a sender-side high-speed enabled TCP congestion control
algorithm, which uses a mixed loss/delay approach to compute the
congestion window. It's design goals target high efficiency, internal,
RTT and Reno fairness, resilience to link loss while keeping network
elements load as low as possible.
For further details look here:
http://wil.cs.caltech.edu/pfldnet2007/paper/YeAH_TCP.pdf
Signed-off-by: Angelo P. Castellani <angelo.castellani@gmail.con>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the SACK-enhanced FRTO given in RFC4138 using the
variant given in Appendix B.
RFC4138, Appendix B:
"This means that in order to declare timeout spurious, the TCP
sender must receive an acknowledgment for non-retransmitted
segment between SND.UNA and RecoveryPoint in algorithm step 3.
RecoveryPoint is defined in conservative SACK-recovery
algorithm [RFC3517]"
The basic version of the FRTO algorithm can still be used also
when SACK is enabled. To enabled SACK-enhanced version, tcp_frto
sysctl is set to 2.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be honest, I'm not too sure how the reord stuff works in the
first place but this seems necessary.
When FRTO has been active, the one and only retransmission could
be unnecessary but the state and sending order might not be what
the sacktag code expects it to be (to work correctly).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP without FRTO would be in Loss state with small cwnd. FRTO,
however, leaves cwnd (typically) to a larger value which causes
ssthresh to become too large in case RTO is triggered again
compared to what conventional recovery would do. Because
consecutive RTOs result in only a single ssthresh reduction,
RTO+cumulative ACK+RTO pattern is required to trigger this
event.
A large comment is included for congestion control module writers
trying to figure out what CA_EVENT_FRTO handler should do because
there exists a remote possibility of incompatibility between
FRTO and module defined ssthresh functions.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously RETRANS bits were cleared on the entry to FRTO. We
postpone that into tcp_enter_frto_loss, which is really the
place were the clearing should be done anyway. This allows
simplification of the logic from a clearing loop to the head skb
clearing only.
Besides, the other changes made in the previous patches to
tcp_use_frto made it impossible for the non-SACKed FRTO to be
entered if other than the head has been rexmitted.
With SACK-enhanced FRTO (and Appendix B), however, there can be
a number retransmissions in flight when RTO expires (same thing
could happen before this patchset also with non-SACK FRTO). To
not introduce any jumpiness into the packet counting during FRTO,
instead of clearing RETRANS bits from skbs during entry, do it
later on.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interpretation comes from RFC4138:
"If the sender implements some loss recovery algorithm other
than Reno or NewReno [FHG04], the F-RTO algorithm SHOULD
NOT be entered when earlier fast recovery is underway."
I think the RFC means to say (especially in the light of
Appendix B) that ...recovery is underway (not just fast recovery)
or was underway when it was interrupted by an earlier (F-)RTO
that hasn't yet been resolved (snd_una has not advanced enough).
Thus, my interpretation is that whenever TCP has ever
retransmitted other than head, basic version cannot be used
because then the order assumptions which are used as FRTO basis
do not hold.
NewReno has only the head segment retransmitted at a time.
Therefore, walk up to the segment that has not been SACKed, if
that segment is not retransmitted nor anything before it, we know
for sure, that nothing after the non-SACKed segment should be
either. This assumption is valid because TCPCB_EVER_RETRANS does
not leave holes but each non-SACKed segment is rexmitted
in-order.
Check for retrans_out > 1 avoids more expensive walk through the
skb list, as we can know the result beforehand: F-RTO will not be
allowed.
SACKed skb can turn into non-SACked only in the extremely rare
case of SACK reneging, in this case we might fail to detect
retransmissions if there were them for any other than head. To
get rid of that feature, whole rexmit queue would have to be
walked (always) or FRTO should be prevented when SACK reneging
happens. Of course RTO should still trigger after reneging which
makes this issue even less likely to show up. And as long as the
response is as conservative as it's now, nothing bad happens even
then.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO controls cwnd when it still processes the ACK input or it
has just reverted back to conventional RTO recovery; the normal
rules apply when FRTO has reverted to standard congestion
control.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because TCP is not in Loss state during FRTO recovery, fast
recovery could be triggered by accident. Non-SACK FRTO is more
robust than not yet included SACK-enhanced version (that can
receiver high number of duplicate ACKs with SACK blocks during
FRTO), at least with unidirectional transfers, but under
extraordinary patterns fast recovery can be incorrectly
triggered, e.g., Data loss+ACK losses => cumulative ACK with
enough SACK blocks to meet sacked_out >= dupthresh condition).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since purpose is to reduce CWND, we prevent immediate growth. This
is not a major issue nor is "the correct way" specified anywhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FRTO detection did not care how ACK pattern affects to cwnd
calculation of the conventional recovery. This caused incorrect
setting of cwnd when the fallback becames necessary. The
knowledge tcp_process_frto() has about the incoming ACK is now
passed on to tcp_enter_frto_loss() in allowed_segments parameter
that gives the number of segments that must be added to
packets-in-flight while calculating the new cwnd.
Instead of snd_una we use FLAG_DATA_ACKED in duplicate ACK
detection because RFC4138 states (in Section 2.2):
If the first acknowledgment after the RTO retransmission
does not acknowledge all of the data that was retransmitted
in step 1, the TCP sender reverts to the conventional RTO
recovery. Otherwise, a malicious receiver acknowledging
partial segments could cause the sender to declare the
timeout spurious in a case where data was lost.
If the next ACK after RTO is duplicate, we do not retransmit
anything, which is equal to what conservative conventional
recovery does in such case.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handles RFC4138 shortcoming (in step 2); it should also have case
c) which ignores ACKs that are not duplicates nor advance window
(opposite dir data, winupdate).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retransmission counter assumptions are to be changed. Forcing
reason to do this exist: Using sysctl in check would be racy
as soon as FRTO starts to ignore some ACKs (doing that in the
following patches). Userspace may disable it at any moment
giving nice oops if timing is right. frto_counter would be
inaccessible from userspace, but with SACK enhanced FRTO
retrans_out can include other than head, and possibly leaving
it non-zero after spurious RTO, boom again.
Luckily, solution seems rather simple: never go directly to Open
state but use Disorder instead. This does not really change much,
since TCP could anyway change its state to Disorder during FRTO
using path tcp_fastretrans_alert -> tcp_try_to_open (e.g., when
a SACK block makes ACK dubious). Besides, Disorder seems to be
the state where TCP should be if not recovering (in Recovery or
Loss state) while having some retransmissions in-flight (see
tcp_try_to_open), which is exactly what happens with FRTO.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a latency spike causes more than one RTO, the later should not
cause the already reduced ssthresh to propagate into the prior_ssthresh
since FRTO declares all such RTOs spurious at once or none of them. In
treating of ssthresh, we mimic what tcp_enter_loss() does.
The previous state (in frto_counter) must be available until we have
checked it in tcp_enter_frto(), and also ACK information flag in
process_frto().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved comments out from the body of process_frto() to the head
(preferred way; see Documentation/CodingStyle). Bonus: it's much
easier to read in this compacted form.
FRTO algorithm and implementation is described in greater detail.
For interested reader, more information is available in RFC4138.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO spurious RTO detection algorithm (RFC4138) does not include response
to a detected spurious RTO but can use different response algorithms.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO was slightly too brave... Should only clear
TCPCB_SACKED_RETRANS bit.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reply to NETLINK_FIB_LOOKUP messages were misrouted back to kernel,
which resulted in infinite recursion and stack overflow.
The bug is present in all kernel versions since the feature appeared.
The patch also makes some minimal cleanup:
1. Return something consistent (-ENOENT) when fib table is missing
2. Do not crash when queue is empty (does not happen, but yet)
3. Put result of lookup
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
draft-nikander-esp-beet-mode-07.txt is not entirely clear on how the length
value of the pseudo header should be calculated, it states "The Header Length
field contains the length of the pseudo header, IPv4 options, and padding in
8 octets units.", but also states "Length in octets (Header Len + 1) * 8".
draft-nikander-esp-beet-mode-08-pre1.txt [1] clarifies this, the header length
should not include the first 8 byte.
This change affects backwards compatibility, but option encapsulation didn't
work until very recently anyway.
[1] http://users.piuha.net/jmelen/BEET/draft-nikander-esp-beet-mode-08-pre1.txt
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to defer congestion control initialization.
If setsockopt() was used to change TCP_CONGESTION before
connection is established, then protocols that use sequence numbers
to keep track of one RTT interval (vegas, illinois, ...) get confused.
Change the init hook to be called after handshake.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two device string comparison loops in arp_packet_match().
The first one goes byte-by-byte but the second one tries to be
clever and cast the string to a long and compare by longs.
The device name strings in the arp table entries are not guarenteed
to be aligned enough to make this value, so just use byte-by-byte
for both cases.
Based upon a report by <drraid@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use put_unaligned to fix warnings about unaligned accesses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clusterip_config_find_get() already increases entries reference
counter, so there is no reason to do it twice in checkentry() callback.
This causes the config to be freed before it is removed from the list,
resulting in a crash when adding the next rule.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases that slow_start_after_idle are meant to deal
with, it is almost a certainty that the congestion window
tests will think the connection is application limited and
we'll thus decrease the cwnd there too. This defeats the
whole point of setting slow_start_after_idle to zero.
So test it there too.
We do not cancel out the entire tcp_cwnd_validate() function
so that if the sysctl is changed we still have the validation
state maintained.
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode looks for the beet pseudo header after the outer IP header,
which is wrong since that is followed by the ESP header. Additionally
it needs to adjust the packet length after removing the pseudo header
and point the data pointer to the real data location.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode decapsulation fails to properly set up the skb pointers, which
only works by accident in combination with CONFIG_NETFILTER, since in that
case the skb is fixed up in xfrm4_input before passing it to the netfilter
hooks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
draft-nikander-esp-beet-mode-07.txt states "The padding MUST be filled
with NOP options as defined in Internet Protocol [1] section 3.1
Internet header format.", so do that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode calculates an incorrect value for the transport header location
when IP options are present, resulting in encapsulation errors.
The correct location is 4 or 8 bytes before the end of the original IP
header, depending on whether the pseudo header is padded.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul E. McKenney writes:
> Those of use who dive into networking only occasionally would much
> appreciate this. ;-)
No problem here...
Acked-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> (but trivial)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a typo which caused fib_props[] to have the wrong size
and makes sure the value used to index the array which is
provided by userspace via netlink is checked to avoid out of
bound access.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Patrick McHardy.
The fib_rules netlink attribute policy introduced in 2.6.19 broke
userspace compatibilty. When specifying a rule with "from all"
or "to all", iproute adds a zero byte long netlink attribute,
but the policy requires all addresses to have a size equal to
sizeof(struct in_addr)/sizeof(struct in6_addr), resulting in a
validation error.
Check attribute length of FRA_SRC/FRA_DST in the generic framework
by letting the family specific rules implementation provide the
length of an address. Report an error if address length is non
zero but no address attribute is provided. Fix actual bug by
checking address length for non-zero instead of relying on
availability of attribute.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently NAT not only reroutes packets in the OUTPUT chain when the
routing key changed, but also if only the non-routing part of the
IPsec policy key changed. This breaks ping -I since it doesn't use
SO_BINDTODEVICE but IP_PKTINFO cmsg to specify the output device, and
this information is lost.
Only do full rerouting if the routing key changed, and just do a new
policy lookup with the old route if only the ports changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcp_mem initialization function. The fraction of total memory
is now a continuous function of memory size, and independent of page
size.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello, Just discussed this Patrick...
We have two users of trie_leaf_remove, fn_trie_flush and fn_trie_delete
both are holding RTNL. So there shouldn't be need for this preempt stuff.
This is assumed to a leftover from an older RCU-take.
> Mhh .. I think I just remembered something - me incorrectly suggesting
> to add it there while we were talking about this at OLS :) IIRC the
> idea was to make sure tnode_free (which at that time didn't use
> call_rcu) wouldn't free memory while still in use in a rcu read-side
> critical section. It should have been synchronize_rcu of course,
> but with tnode_free using call_rcu it seems to be completely
> unnecessary. So I guess we can simply remove it.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill warning about unused variable `in_dev' when CONFIG_IP_MULTICAST
is not set.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 484b366932 added support for the CIPSO
ranged categories tag. However, it appears that I made a mistake when rebasing
then patch to the latest upstream sources for submission and dropped the part
of the patch that actually parses the tag on incoming packets. This patch
fixes this mistake by adding the required function call to the
cipso_v4_skbuff_getattr() function.
I've run this patch over the weekend and have not noticed any problems.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return negative error value (embedded in the pointer) instead of
returning NULL.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some stacks apparently send packets with SYN|URG set. Linux accepts
these packets, so TCP conntrack should to.
Pointed out by Martijn Posthuma <posthuma@sangine.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_netlink config option is named CONFIG_NF_CT_NETLINK,
but multiple files use CONFIG_IP_NF_CONNTRACK_NETLINK or
CONFIG_NF_CONNTRACK_NETLINK for ifdefs.
Fix this and reformat all CONFIG_NF_CT_NETLINK ifdefs to only use a line.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix {nf,ip}_ct_iterate_cleanup unconfirmed list handling:
- unconfirmed entries can not be killed manually, they are removed on
confirmation or final destruction of the conntrack entry, which means
we might iterate forever without making forward progress.
This can happen in combination with the conntrack event cache, which
holds a reference to the conntrack entry, which is only released when
the packet makes it all the way through the stack or a different
packet is handled.
- taking references to an unconfirmed entry and using it outside the
locked section doesn't work, the list entries are not refcounted and
another CPU might already be waiting to destroy the entry
What the code really wants to do is make sure the references of the hash
table to the selected conntrack entries are released, so they will be
destroyed once all references from skbs and the event cache are dropped.
Since unconfirmed entries haven't even entered the hash yet, simply mark
them as dying and skip confirmation based on that.
Reported and tested by Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current CIPSO engine has a problem where it does not verify that
the given sensitivity level has a valid CIPSO mapping when the "std"
CIPSO DOI type is used. The end result is that bad packets are sent
on the wire which should have never been sent in the first place.
This patch corrects this problem by verifying the sensitivity level
mapping similar to what is done with the category mapping. This patch
also changes the returned error code in this case to -EPERM to better
match what the category mapping verification code returns.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 2/28/07, KOVACS Krisztian <hidden@balabit.hu> wrote:
>
> Hi,
>
> While reading TCP minisock code I've found this suspiciously looking
> code fragment:
>
> - 8< -
> struct sock *tcp_create_openreq_child(struct sock *sk, struct request_sock *req, struct sk_buff *skb)
> {
> struct sock *newsk = inet_csk_clone(sk, req, GFP_ATOMIC);
>
> if (newsk != NULL) {
> const struct inet_request_sock *ireq = inet_rsk(req);
> struct tcp_request_sock *treq = tcp_rsk(req);
> struct inet_connection_sock *newicsk = inet_csk(sk);
> struct tcp_sock *newtp;
> - 8< -
>
> The above code initializes newicsk to inet_csk(sk), isn't that supposed
> to be inet_csk(newsk)? As far as I can tell this might leave
> icsk_ack.last_seg_size zero even if we do have received data.
Good catch!
David, please apply the attached patch.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 2.6.21-rc1, I get an oops when running 'ifdown eth0' and an IPsec
connection is active. If I shut down the connection before running 'ifdown
eth0', then there's no problem. The critical operation of this script is to
kill dhcpd.
The problem is probably caused by commit with git identifier
4337226228 (Linus tree) "[IPSEC]: IPv4 over IPv6
IPsec tunnel".
This patch fixes that oops. I don't know the network code of the Linux
kernel in deep, so if that fix is wrong, please change it. But please
fix the oops. :)
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please consider applying, this was found on your latest
net-2.6 tree while playing around with that ip_hdr() + turn
skb->nh/h/mac pointers as offsets on 64 bits idea :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allocates inetdev at registration for all devices
in line with IPv6. This allows sysctl configuration on the
devices to occur before they're brought up or addresses are
added.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
The locking calls assumed that these code paths were only
invoked in software interrupt context, but that isn't true.
Therefore we need to use spin_{lock,unlock}_bh() throughout.
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
It isn't needed anymore, all of the users are gone, and all of the ctl_table
initializers have been converted to use explicit names of the fields they are
initializing.
[akpm@osdl.org: NTFS fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes xfrm4_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP may advertize up to 16-bits window in SYN packets (no window
scaling allowed). At the same time, TCP may have rcv_wnd
(32-bits) that does not fit to 16-bits without window scaling
resulting in pseudo garbage into advertized window from the
low-order bits of rcv_wnd. This can happen at least when
mss <= (1<<wscale) (see tcp_select_initial_window). This patch
fixes the handling of SYN advertized windows (compile tested
only).
In worst case (which is unlikely to occur though), the receiver
advertized window could be just couple of bytes. I'm not sure
that such situation would be handled very well at all by the
receiver!? Fortunately, the situation normalizes after the
first non-SYN ACK is received because it has the correct,
scaled window.
Alternatively, tcp_select_initial_window could be changed to
prevent too large rcv_wnd in the first place.
[ tcp_make_synack() has the same bug, and I've added a fix for
that to this patch -DaveM ]
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCP reset packet is copied from the original. This
includes all the GSO bits which do not apply to the new
packet. So we should clear those bits.
Spotted by Patrick McHardy.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor non-invasive cleanups:
* white space around operators and line wrapping
* use const
* use __read_mostly
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These module parameters should be in the read mostly area to avoid
cache pollution.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of depending on internally needed options and letting users
figure out what is needed, select them when needed:
- IP_NF_IPTABLES, IP_NF_ARPTABLES and IP6_NF_IPTABLES select
NETFILTER_XTABLES
- NETFILTER_XT_TARGET_CONNMARK, NETFILTER_XT_MATCH_CONNMARK and
IP_NF_TARGET_CLUSTERIP select NF_CONNTRACK_MARK
- NETFILTER_XT_MATCH_CONNBYTES selects NF_CT_ACCT
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONNTRACK_STAT_INC assumes rcu_read_lock in nf_hook_slow disables
preemption as well, making it legal to use __get_cpu_var without
disabling preemption manually. The assumption is not correct anymore
with preemptable RCU, additionally we need to protect against softirqs
when not holding ip_conntrack_lock.
Add CONNTRACK_STAT_INC_ATOMIC macro, which disables local softirqs,
and use where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
paths used outside of packet processing context (nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
paths used outside of packet processing context (nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- rename nf_logging to nf_loggers since its an array of registered loggers
- rename nf_log_unregister_logger() to nf_log_unregister() to make it
symetrical to nf_log_register() and convert all users
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use rcu_assign_pointer/rcu_dereference for ip_ct_attach pointer instead
of self-made RCU and use rcu_read_lock to make sure the conntrack module
doesn't disappear below us while calling it, since this function can be
called from outside the netfilter hooks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I forgot to test build this part of the networking code... Sorry guys.
This patch renames u.rt_next to u.dst.rt_next
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the rt_next pointer from 'struct rtable.u' union,
and renames u.rt_next to u.dst_rt_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
the gain on lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a prior patch, I introduced a sk_hash field (__sk_common.skc_hash) to let
tcp lookups use one cache line per unmatched entry instead of two.
We can also use sk_hash to speedup UDP part as well. We store in sk_hash the
hnum value, and use sk->sk_hash (same cache line than 'next' pointer),
instead of inet->num (different cache line)
Note : We still have a false sharing problem for SMP machines, because
sock_hold(sock) dirties the cache line containing the 'next' pointer. Not
counting the udp_hash_lock rwlock. (did someone mentioned RCU ? :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehash table layout is currently this one :
First half of this table is used by sockets not in TIME_WAIT state
Second half of it is used by sockets in TIME_WAIT state.
This is non optimal because of for a given hash or socket, the two chain heads
are located in separate cache lines.
Moreover the locks of the second half are never used.
If instead of this halving, we use two list heads in inet_ehash_bucket instead
of only one, we probably can avoid one cache miss, and reduce ram usage,
particularly if sizeof(rwlock_t) is big (various CONFIG_DEBUG_SPINLOCK,
CONFIG_DEBUG_LOCK_ALLOC settings). So we still halves the table but we keep
together related chains to speedup lookups and socket state change.
In this patch I did not try to align struct inet_ehash_bucket, but a future
patch could try to make this structure have a convenient size (a power of two
or a multiple of L1_CACHE_SIZE).
I guess rwlock will just vanish as soon as RCU is plugged into ehash :) , so
maybe we dont need to scratch our heads to align the bucket...
Note : In case struct inet_ehash_bucket is not a power of two, we could
probably change alloc_large_system_hash() (in case it use __get_free_pages())
to free the unused space. It currently allocates a big zone, but the last
quarter of it could be freed. Again, this should be a temporary 'problem'.
Patch tested on ipv4 tcp only, but should be OK for IPV6 and DCCP.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the x_tables functions directly to make it better visible which
parts are shared between ip_tables and ip6_tables.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to NAT to randomize source ports.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do liberal tracking (only RSTs need to be in-window) for connections picked
up without seeing a SYN to deal with window scaling. Also change logging
of invalid packets not to log packets accepted by liberal tracking to avoid
spamming the logs.
Based on suggestion from James Ralston <ralston@pobox.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was no real useful information from the unregister_netdevice() return
code, the only error occurred in a situation that was a driver bug. So
change it to a void function.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add_grhead() allocates memory with GFP_ATOMIC and in at least two places skb
from it passed to skb_put() without checking.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we can't find the afinfo we should return EAFNOSUPPORT.
GCC warned about the uninitialized 'err' for this path as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the patch to support IPv4 over IPv6 IPsec.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the patch to support IPv6 over IPv4 IPsec
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports xfrm_state_afinfo.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We clear the unused parts of the SACK cache, This prevents us from mistakenly
taking the cache data if the old data in the SACK cache is the same as the data
in the SACK block. This assumes that we never receive an empty SACK block with
start and end both at zero.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move DSACK code outside the SACK fast-path checking code. If the DSACK
determined that the information was too old we stayed with a partial cache
copied. Most likely this matters very little since the next packet will not be
DSACK and we will find it in the cache. but it's still not good form and there
is little reason to couple the two checks.
Since the SACK receive cache doesn't need the data to be in host order we also
remove the ntohl in the checking loop.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only advance the SACK fast-path pointer for the first block, the
fast-path assumes that only the first block advances next time so we
should not move the cached skb for the next sack blocks.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcphdr struct passed to tcp_v4_check is not used, the following
patch removes it from the parameter list.
This adds the netfilter modifications missing in the patch I sent
for rc3-mm1.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netlink users BUG when the allocated skb for an event
notification is undersized. While this is certainly a kernel bug,
its not critical and crashing the kernel is too drastic, especially
when considering that these errors have appeared multiple times in
the past and it BUGs even if no listeners are present.
This patch replaces BUG by WARN_ON and changes the notification
functions to inform potential listeners of undersized allocations
using a unique error code (EMSGSIZE).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for an @-sign in skp_epaddr_len, make sure not to
run over the packet boundaries.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to skip over the username in the Contact header, stop at the
end of the line if no @ is found to avoid mangling following headers.
We don't need to worry about continuation lines because we search inside
a SIP URI.
Fixes Netfilter Bugzilla #532.
Signed-off-by: Lars Immisch <lars@ibp.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When main table is just a single leaf this gets printed as belonging to the
local table in /proc/net/fib_trie. A fix is below.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the expectation for the opposite direction, the PPTP NAT
helper initializes the tuple for lookup with the addresses of the
opposite direction, which makes the lookup fail.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nf_nat/nf_conntrack_ipv4 are linked statically, nf_nat is initialized
before nf_conntrack_ipv4, which makes the nf_ct_l3proto_find_get(AF_INET)
call during nf_nat initialization return the generic l3proto instead of
the AF_INET specific one. This breaks ICMP error translation since the
generic protocol always initializes the IPs in the tuple to 0.
Change the linking order and put nf_conntrack_ipv4 first.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert 931731123a
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sorting of SACK blocks actually munges them rather than sort,
causing the TCP stack to ignore some SACK information and breaking the
assumption of ordered SACK blocks after sorting.
The sort takes the data from a second buffer which isn't moved causing
subsequent data moves to occur from the wrong location. The fix is to
use a temporary buffer as a normal sort does.
Signed-off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a kernel with trie routing enabled I had a simple routing setup
with only a single route to the outside world and no default
route. "ip route table list main" showed my the route just fine but
/proc/net/route was an empty file. What was going on?
Thinking it was a bug in something I did and I looked deeper. Eventually
I setup a second route and everything looked correct, huh? Finally I
realized that the it was just the iterator pair in fib_trie_get_first,
fib_trie_get_next just could not handle a routing table with a single entry.
So to save myself and others further confusion, here is a simple fix for
the fib proc iterator so it works even when there is only a single route
in a routing table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "Replace CHECKSUM_HW by CHECKSUM_PARTIAL/CHECKSUM_COMPLETE"
changed to unconditional copying of ip_summed field from collapsed
skb. This patch reverts this change.
The majority of substantial work including heavy testing
and diagnosing by: Michael Tokarev <mjt@tls.msk.ru>
Possible reasons pointed by: Herbert Xu and Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered a kernel panic with my test program, which is a very
simple IPv6 client-server program.
The server side sets IPV6_RECVPKTINFO on a listening socket, and the
client side just sends a message to the server. Then the kernel panic
occurs on the server. (If you need the test program, please let me
know. I can provide it.)
This problem happens because a skb is forcibly freed in
tcp_rcv_state_process().
When a socket in listening state(TCP_LISTEN) receives a syn packet,
then tcp_v6_conn_request() will be called from
tcp_rcv_state_process(). If the tcp_v6_conn_request() successfully
returns, the skb would be discarded by __kfree_skb().
However, in case of a listening socket which was already set
IPV6_RECVPKTINFO, an address of the skb will be stored in
treq->pktopts and a ref count of the skb will be incremented in
tcp_v6_conn_request(). But, even if the skb is still in use, the skb
will be freed. Then someone still using the freed skb will cause the
kernel panic.
I suggest to use kfree_skb() instead of __kfree_skb().
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change my email address to reflect OSDL merger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
[ The irony. Somebody still has his sign-off message hardcoded
in a script or his brainstem ;^]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
inetdev_init out label moved after RCU assignment
(final suggestion by Herbert Xu)
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A quick patch to change the inet_sock->is_icsk assignment to better fit with
existing kernel coding style.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading the NAT module, existing connection tracking entries don't
have room for NAT information allocated and packets are dropped, causing
hanging connections. They really should be entered into the NAT table
as NULL mappings, but the current allocation scheme doesn't allow this.
For now simply accept those packets to avoid the hanging connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the ftp stalls present in the current kernels.
All credit goes to Komuro <komurojun-mbn@nifty.com> for tracking
this down. The patch is untested but it looks *cough* obviously
correct.
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet_create() and inet6_create() functions incorrectly set the
inet_sock->is_icsk field. Both functions assume that the is_icsk field is
large enough to hold at least a INET_PROTOSW_ICSK value when it is actually
only a single bit. This patch corrects the assignment by doing a boolean
comparison whose result will safely fit into a single bit field.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is important that we only assign dev->ip{,6}_ptr
only after all portions of the inet{,6} are setup.
Otherwise we can receive packets before the multicast
spinlocks et al. are initialized.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return value of nfct_nat() in device_cmp(), we might very well
have non NAT conntrack entries as well (Netfilter bugzilla #528).
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets generated by the REJECT target in the output chain have a local
destination address and a foreign source address. Make sure not to use
the foreign source address for the output route lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used by compat code offsets of entries should be 'unsigned int' as entries
array size has this dimension.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this code was converted to use sk_for_each() the
logic for the "best hash chain length" code was reversed,
breaking everything.
The original code was of the form:
size = 0;
do {
if (++size >= best_size_so_far)
goto next;
} while ((sk = sk->next) != NULL);
best_size_so_far = size;
best = result;
next:;
and this got converted into:
sk_for_each(sk2, node, head)
if (++size < best_size_so_far) {
best_size_so_far = size;
best = result;
}
Which does something very very different from the original.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the redirect packet of the router if the jiffies wraparound.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message logged in tcp_v4_inbound_md5_hash when the hash was expected
but not found was reversed.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
md5sig_info.alloced4 must be set to zero when freeing keys4, otherwise
it will not be alloc'd again when another key is added to the same
socket by tcp_v4_md5_do_add.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should call tcp_free_md5sig_pool() not __tcp_free_md5sig_pool()
so that it does proper refcounting.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we come to node we'd already marked as seen and it's not a part of path
(i.e. we don't have a loop right there), we already know that it isn't a
part of any loop, so we don't need to revisit it.
That speeds the things up if some chain is refered to from several places
and kills O(exp(table size)) worst-case behaviour (without sleeping,
at that, so if you manage to self-LART that way, you are SOL for a long
time)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matches and targets verification is duplicated in normal and compat processing
ways. This patch refactors code in order to remove this.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLUSTERIP, CONNMARK, CONNSECMARK, and connbytes need ip_conntrack or
layer 3 protocol module of nf_conntrack.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Manners notices that when an IPVS synchonisation daemons are
started the system load slowly climbs up to 1. This seems to be related
to the call to ssleep(1) (aka msleep(1000) in the main loop. Replacing
this with a call to msleep_interruptable() seems to make the problem go
away. Though I'm not sure that it is correct.
This is the second edition of this patch, which replaces ssleep()
in the main loop for both the master and backup threads, as well
as some thread synchronisation code. The latter is just for thorougness
as it shouldn't be causing any problems.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hard header cache is in the main output path, so using
seqlock instead of reader/writer lock should reduce overhead.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As per Ralf Baechle's observations, the schedule_work() call
should give enough of a memory barrier, so the explicit one
here is totally unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe all the below memory barriers only matter on SMP so
therefore the smp_* variant of the barrier should be used.
I'm wondering if the barrier in net/ipv4/inet_timewait_sock.c should be
dropped entirely. schedule_work's implementation currently implies a
memory barrier and I think sane semantics of schedule_work() should imply
a memory barrier, as needed so the caller shouldn't have to worry.
It's not quite obvious why the barrier in net/packet/af_packet.c is
needed; maybe it should be implied through flush_dcache_page?
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We grab a reference to the route's inetpeer entry but
forget to release it in xfrm4_dst_destroy().
Bug discovered by Kazunori MIYAZAWA <kazunori@miyazawa.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In compat mode, matches and targets valid hooks checks always successful due
to not initialized e->comefrom field yet. This patch separates this checks from
translation code and moves them after mark_source_chains() call, where these
marks are initialized.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by; Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 590bdf7fd2 introduced a regression
in match/target hook validation. mark_source_chains builds a bitmask
for each rule representing the hooks it can be reached from, which is
then used by the matches and targets to make sure they are only called
from valid hooks. The patch moved the match/target specific validation
before the mark_source_chains call, at which point the mask is always zero.
This patch returns back to the old order and moves the standard checks
to mark_source_chains. This allows to get rid of a special case for
standard targets as a nice side-effect.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the behaviour of disable_xfrm is inconsistent between
locally generated and forwarded packets. For locally generated
packets disable_xfrm disables the policy lookup if it is set on
the output device, for forwarded traffic however it looks at the
input device. This makes it impossible to disable xfrm on all
devices but a dummy device and use normal routing to direct
traffic to that device.
Always use the output device when checking disable_xfrm.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
- move EXPORT_SYMBOL next to exported symbol
- use EXPORT_SYMBOL_GPL since this is what the original code used
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the references to "new connection tracking" from Kconfig.
After some short stabilization period of the new connection tracking
helpers/NAT code the old one will be removed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the TFTP conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the SIP conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_conntrack port of the PPtP conntrack/NAT helper. Since there seems
to be no IPv6-capable PPtP implementation the helper only support IPv4.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_conntrack port of the IRC conntrack/NAT helper. Since DCC doesn't
support IPv6 yet, the helper is still IPv4 only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the H.323 conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the Amanda conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FTP NAT helper.
Split out from Jozsef's big nf_nat patch with a few small fixes by myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAT support for nf_conntrack. Joint work of Jozsef Kadlecsik,
Yasuyuki Kozakai, Martin Josefsson and myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the connection tracking selection (well, the user experience,
not really the aesthetics) by offering one option to enable connection
tracking and a choice between the implementations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resync with Al Viro's ip_conntrack annotations and fix a missed
spot in ip_nat_proto_icmp.c.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CONNTRACK_PROC_COMPAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups:
- make the following needlessly global functions statis:
- ipv4/tcp.c: __tcp_alloc_md5sig_pool()
- ipv4/tcp_ipv4.c: tcp_v4_reqsk_md5_lookup()
- ipv4/udplite.c: udplite_rcv()
- ipv4/udplite.c: udplite_err()
- make the following needlessly global structs static:
- ipv4/tcp_ipv4.c: tcp_request_sock_ipv4_ops
- ipv4/tcp_ipv4.c: tcp_sock_ipv4_specific
- ipv6/tcp_ipv6.c: tcp_request_sock_ipv6_ops
- net/ipv{4,6}/udplite.c: remove inline's from static functions
(gcc should know best when to inline them)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just obfuscates the code and adds limited value. And as Adrian
Bunk noticed, it lacked Kconfig help text too, so just kill it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ranged tag (tag type #5) to the CIPSOv4 protocol.
The ranged tag allows for seven, or eight if zero is the lowest category,
category ranges to be specified in a CIPSO option. Each range is specified by
two unsigned 16 bit fields, each with a maximum value of 65534. The two values
specify the start and end of the category range; if the start of the category
range is zero then it is omitted.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add support for the enumerated tag (tag type #2) to the CIPSOv4 protocol.
The enumerated tag allows for 15 categories to be specified in a CIPSO option,
where each category is an unsigned 16 bit field with a maximum value of 65534.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The original NetLabel category bitmap was a straight char bitmap which worked
fine for the initial release as it only supported 240 bits due to limitations
in the CIPSO restricted bitmap tag (tag type 0x01). This patch converts that
straight char bitmap into an extensibile/sparse bitmap in order to lay the
foundation for other CIPSO tag types and protocols.
This patch also has a nice side effect in that all of the security attributes
passed by NetLabel into the LSM are now in a format which is in the host's
native byte/bit ordering which makes the LSM specific code much simpler; look
at the changes in security/selinux/ss/ebitmap.c as an example.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add new NFLOG target to allow use of nfnetlink_log for both IPv4 and IPv6.
Currently we have two (unsupported by userspace) hacks in the LOG and ULOG
targets to optionally call to the nflog API. They lack a few features,
namely the IPv4 and IPv6 LOG targets can not specify a number of arguments
related to nfnetlink_log, while the ULOG target is only available for IPv4.
Remove those hacks and add a clean way to use nfnetlink_log.
Signed-off-by: Patrick McHardy <kaber@trash.net>
| NEW | UPDATE | DESTROY |
----------------------------------------|
tuples | Y | Y | Y |
status | Y | Y | N |
timeout | Y | Y | N |
protoinfo | S | S | N |
helper | S | S | N |
mark | S | S | N |
counters | F | F | Y |
Leyend:
Y: yes
N: no
S: iif the field is set
F: iif overflow
This patch also replace IPCT_HELPINFO by IPCT_HELPER since we want to
track the helper assignation process, not the changes in the private
information held by the helper.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Check that status flags are available in the netlink message received
to create a new conntrack.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The NAT handling of the SIP helper has a few problems:
- Request headers are only mangled in the reply direction, From/To headers
not at all, which can lead to authentication failures with DNAT in case
the authentication domain is the IP address
- Contact headers in responses are only mangled for REGISTER responses
- Headers may be mangled even though they contain addresses not
participating in the connection, like alternative addresses
- Packets are droppen when domain names are used where the helper expects
IP addresses
This patch takes a different approach, instead of fixed rules what field
to mangle to what content, it adds symetric mapping of From/To/Via/Contact
headers, which allows to deal properly with echoed addresses in responses
and foreign addresses not belonging to the connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Not every header has a shortcut, so make them optional instead
of searching for the same string twice.
Signed-off-by: Patrick McHardy <kaber@trash.net>
- Use enum for header field enumeration
- Use numerical value instead of pointer to header info structure to
identify headers, unexport ct_sip_hdrs
- group SIP and SDP entries in header info structure
- remove double forward declaration of ct_sip_get_info
Signed-off-by: Patrick McHardy <kaber@trash.net>
The NAT helpr hooks are protected by RCU, but all of the
conntrack helpers test and use the global pointers instead
of copying them first using rcu_dereference()
Also replace synchronize_net() by synchronize_rcu() for clarity
since sychronizing only with packet receive processing is
insufficient to prevent races.
Signed-off-by: Patrick McHardy <kaber@trash.net>
We usually uses 'xxx_find_get' for function which increments
reference count.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds /proc/net/ip_conntrack, /proc/net/ip_conntrack_expect and
/proc/net/stat/ip_conntrack files to keep old programs using them working.
The /proc/net/ip_conntrack and /proc/net/ip_conntrack_expect files show only
IPv4 entries, the /proc/net/stat/ip_conntrack shows global statistics.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove unused struct list_head from struct nf_conntrack_l3proto and
nf_conntrack_l4proto as all protocols are kept in arrays, not linked
lists.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Rename 'struct nf_conntrack_protocol' to 'struct nf_conntrack_l4proto' in
order to help distinguish it from 'struct nf_conntrack_l3proto'. It gets
rather confusing with 'nf_conntrack_protocol'.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch consolidates set/getsockopt code between UDP(-Lite) v4 and 6. The
justification is that UDP(-Lite) is a transport-layer protocol and therefore
the socket option code (at least in theory) should be AF-independent.
Furthermore, there is the following code reduplication:
* do_udp{,v6}_getsockopt is 100% identical between v4 and v6
* do_udp{,v6}_setsockopt is identical up to the following differerence
--v4 in contrast to v4 additionally allows the experimental encapsulation
types UDP_ENCAP_ESPINUDP and UDP_ENCAP_ESPINUDP_NON_IKE
--the remainder is identical between v4 and v6
I believe that this difference is of little relevance.
The advantages in not duplicating twice almost completely identical code.
The patch further simplifies the interface of udp{,v6}_push_pending_frames,
since for the second argument (struct udp_sock *up) it always holds that
up = udp_sk(sk); where sk is the first function argument.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4, IPv6, and DECNet all use struct rta_cacheinfo in a similiar
way, therefore rtnl_put_cacheinfo() is added to reuse code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination PID is passed directly to netlink_unicast()
respectively netlink_multicast().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and switch the damn checksum update to something saner
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cipso_v4_doi_search() function behaves the same as cipso_v4_doi_getdef()
but is a local, static function so use it whenever possibile in the CIPSOv4
code base.
Signed-of-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The CIPSOv4 translated tag #1 mapping does not always return the correct error
code if the desired mapping does not exist; instead of returning -EPERM it
returns -ENOSPC indicating that the buffer is not large enough to hold the
translated value. This was caused by failing to check a specific error
condition. This patch fixes this so that unknown mappings return
-EPERM which is consistent with the rest of the related CIPSOv4 code.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
While the original CIPSOv4 code had provisions for multiple tag types the
implementation was not as great as it could be, pushing a lot of non-tag
specific processing into the tag specific code blocks. This patch fixes that
issue making it easier to support multiple tag types in the future.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently the CIPSOv4 engine does not do any sort of checking when a new DOI
definition is added. The tags are still verified but only as a side effect of
normal NetLabel operation (packet processing, socket labeling, etc.) which
would cause application errors due to the faulty configuration. This patch
adds tag checking when new DOI definition are added allowing us to catch these
configuration problems when they happen.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Right now the NetLabel code always jumps into the CIPSOv4 layer to determine if
a CIPSO IP option is present. However, we can do this check directly in the
NetLabel code by making use of the CIPSO_V4_OPTEXIST() macro which should save
us a function call in the common case of not having a CIPSOv4 option present.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The existing netlbl_lsm_secattr struct required the LSM to check all of the
fields to determine if any security attributes were present resulting in a lot
of work in the common case of no attributes. This patch adds a 'flags' field
which is used to indicate which attributes are present in the structure; this
should allow the LSM to do a quick comparison to determine if the structure
holds any security attributes.
Example:
if (netlbl_lsm_secattr->flags)
/* security attributes present */
else
/* NO security attributes present */
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
udp_push_pending_frames is only referenced within
net/ipv4/udp.c and hence can remain static.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a revision of the previously submitted patch, which alters
the way files are organized and compiled in the following manner:
* UDP and UDP-Lite now use separate object files
* source file dependencies resolved via header files
net/ipv{4,6}/udp_impl.h
* order of inclusion files in udp.c/udplite.c adapted
accordingly
[NET/IPv4]: Support for the UDP-Lite protocol (RFC 3828)
This patch adds support for UDP-Lite to the IPv4 stack, provided as an
extension to the existing UDPv4 code:
* generic routines are all located in net/ipv4/udp.c
* UDP-Lite specific routines are in net/ipv4/udplite.c
* MIB/statistics support in /proc/net/snmp and /proc/net/udplite
* shared API with extensions for partial checksum coverage
[NET/IPv6]: Extension for UDP-Lite over IPv6
It extends the existing UDPv6 code base with support for UDP-Lite
in the same manner as per UDPv4. In particular,
* UDPv6 generic and shared code is in net/ipv6/udp.c
* UDP-Litev6 specific extensions are in net/ipv6/udplite.c
* MIB/statistics support in /proc/net/snmp6 and /proc/net/udplite6
* support for IPV6_ADDRFORM
* aligned the coding style of protocol initialisation with af_inet6.c
* made the error handling in udpv6_queue_rcv_skb consistent;
to return `-1' on error on all error cases
* consolidation of shared code
[NET]: UDP-Lite Documentation and basic XFRM/Netfilter support
The UDP-Lite patch further provides
* API documentation for UDP-Lite
* basic xfrm support
* basic netfilter support for IPv4 and IPv6 (LOG target)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just some mis-placed ifdefs:
net/ipv4/tcp_minisocks.c: In function ‘tcp_twsk_destructor’:
net/ipv4/tcp_minisocks.c:364: warning: unused variable ‘twsk’
net/ipv6/tcp_ipv6.c:1846: warning: ‘tcp_sock_ipv6_specific’ defined but not used
net/ipv6/tcp_ipv6.c:1877: warning: ‘tcp_sock_ipv6_mapped_specific’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the TCP/DCCP (and tunnelling) code, it often happens that the
return code of a transmit function needs to be tested against NET_XMIT_CN
which is a value that does not indicate a strict error condition.
This patch uses a macro for these recurring situations which is consistent
with the already existing macro net_xmit_errno, saving on duplicated code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Account for the netlink message header size directly in nlmsg_new()
instead of relying on the caller calculate it correctly.
Replaces error handling of message construction functions when
constructing notifications with bug traps since a failure implies
a bug in calculating the size of the skb.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes two redundancies:
1) The test (skb->protocol == htons(ETH_P_IPV6) in tcp_v6_init_sequence()
is always true, due to
* tcp_v6_conn_request() is the only function calling this one
* tcp_v6_conn_request() redirects all skb's with ETH_P_IP protocol to
tcp_v4_conn_request() [ cf. top of tcp_v6_conn_request()]
2) The first argument, `struct sock *sk' of tcp_v{4,6}_init_sequence() is
never used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data itself is already charged to the SKB, doing
the skb_set_owner_w() just generates a lot of noise and
extra atomics we don't really need.
Lmbench improvements on lat_tcp are minimal:
before:
TCP latency using localhost: 23.2701 microseconds
TCP latency using localhost: 23.1994 microseconds
TCP latency using localhost: 23.2257 microseconds
after:
TCP latency using localhost: 22.8380 microseconds
TCP latency using localhost: 22.9465 microseconds
TCP latency using localhost: 22.8462 microseconds
Signed-off-by: David S. Miller <davem@davemloft.net>
If user has permision to load modules, then autoload then attempt
autoload of TCP congestion module.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow normal users to only choose among a restricted set of congestion
control choices. The default is reno and what ever has been configured
as default. But the policy can be changed by administrator at any time.
For example, to allow any choice:
cp /proc/sys/net/ipv4/tcp_available_congestion_control \
/proc/sys/net/ipv4/tcp_allowed_congestion_control
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create /proc/sys/net/ipv4/tcp_available_congestion_control
that reflects currently available TCP choices.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allocate a fixed size (TCP_SYNQ_HSIZE=512) slots hash table for
each LISTEN socket, regardless of various parameters (listen backlog for
example)
On x86_64, this means order-1 allocations (might fail), even for 'small'
sockets, expecting few connections. On the contrary, a huge server wanting a
backlog of 50000 is slowed down a bit because of this fixed limit.
This patch makes the sizing of listen hash table a dynamic parameter,
depending of :
- net.core.somaxconn tunable (default is 128)
- net.ipv4.tcp_max_syn_backlog tunable (default : 256, 1024 or 128)
- backlog value given by user application (2nd parameter of listen())
For large allocations (bigger than PAGE_SIZE), we use vmalloc() instead of
kmalloc().
We still limit memory allocation with the two existing tunables (somaxconn &
tcp_max_syn_backlog). So for standard setups, this patch actually reduce RAM
usage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the attribute policy for the non-specific attributes into
net/fib_rules.h and include it in the respective protocols.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mark selector currently implemented per protocol into
the protocol independant part.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all protocols have been made aware of the mark
field it can be moved out of the union thus simplyfing
its usage.
The config options in the IPv4/IPv6/DECnet subsystems
to enable respectively disable mark based routing only
obfuscate the code with ifdefs, the cost for the
additional comparison in the flow key is insignificant,
and most distributions have all these options enabled
by default anyway. Therefore it makes sense to remove
the config options and enable mark based routing by
default.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfmark is being used in various subsystems and has become
the defacto mark field for all kinds of packets. Therefore
it makes sense to rename it to `mark' and remove the
dependency on CONFIG_NETFILTER.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix SO_PEERSEC for tcp sockets to return the security context of
the peer (as represented by the SA from the peer) as opposed to the
SA used by the local/source socket.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
