Anatolij 52xx updates:
Patch for pcm030 device tree fixing the probe() in pcm030-audio-fabric
driver. Changes to this driver have been merged in 3.7-rc1 via ASoC
tree, but this required device tree patch was submitted separately to
the linux-ppc list and is still missing in mainline. Without this patch
the probe() in pcm030-audio-fabric driver wrongly returns -ENODEV.
A patch from Wolfram fixing wrong invalid critical irq warnings for
all mpc5200 boards.
Another patch for all mpc5200 device trees fixing wrong L1 cell in
the LPB FIFO interrupt property and moving the LPB FIFO node to the
common mpc5200b.dtsi file so that this common node will be present
in all mpc5200 device trees.
Don't even momentarily set the pause status when starting the channel;
if we do, we should check the busy bit to ensure that we comply with
the spec. In any case, it isn't necessary; we will not active on a
START event so there is no need to pause the DMA.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stress testing the driver with multiple start/stop events causes
kirkwood-dma to report underrun errors (which used to cause the kernel
to lock up solidly). This is because kirkwood-i2s is not respecting
the restrictions imposed on clearing the 'pause' bit. Follow what the
spec says; the busy bit must be read as being clear twice before the
pause bit can be released. This solves the underruns.
However, it has been noticed that the busy bit occasionally does not
clear itself, hence the waiting is bounded to 5ms maximum to avoid a
new reason for the kernel to lockup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is part of a patch found in Rabeeh Khoury's git tree for the
cubox, which is further attributed to Sebastian Hesselbrath.
Rather than masking the KIRKWOOD_DCO_SPCR_STATUS register contents
against the registers virtual address, let's actually use the bit
definition for the locked status, as required in the documentation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ignoring the real cause of the interrupt is not a good idea; this
behaviour has been observed to bring Dove platforms to silently
lockup. Instead, on error fall through to the normal interrupt
processing.
This is especially important on Dove platforms as errors are
handled separately, and allows us to clear down the real cause of
the interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is part of a patch found in Rabeeh Khoury's git tree for the
cubox.
You can not use virt_to_phys() on the address returned from
dma_alloc_coherent(); it may not be part of the kernel direct-mapped
memory. Fix this to use the DMA address instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building for Athlon/Duron/K7 results in the following build error,
arch/x86/boot/compressed/eboot.o: In function `__constant_memcpy3d':
eboot.c:(.text+0x385): undefined reference to `_mmx_memcpy'
arch/x86/boot/compressed/eboot.o: In function `efi_main':
eboot.c:(.text+0x1a22): undefined reference to `_mmx_memcpy'
because the boot stub code doesn't link with the kernel proper, and
therefore doesn't have access to the 3DNow version of memcpy. So,
follow the example of misc.c and #undef memcpy so that we use the
version provided by misc.c.
See https://bugzilla.kernel.org/show_bug.cgi?id=50391
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Ryan Underwood <nemesis@icequake.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Commit 71c6c837 (drivers/net: fix tasklet misuse issue) introduced a
build failure in the xilinx driver. axienet_dma_err_handler isn't
declared before its use in axienet_open.
This patch provides the prototype before axienet_open.
Cc: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e064b1 (x86, efi: Fix issue of overlapping .reloc section for
EFI_STUB) removed a dummy reloc added by commit 291f363 (x86, efi: EFI
boot stub support), but forgot to remove the dummy long used by that
reloc.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
In case of error, inet6_csk_update_pmtu() should consistently
return NULL.
Bug added in commit 35ad9b9cf7
(ipv6: Add helper inet6_csk_update_pmtu().)
Reported-by: Lluís Batlle i Rossell <viric@viric.name>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use &port->netdev->dev instead of NULL since dma_pool_create() doesn't
allow NULL dev.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use &port->netdev->dev instead of NULL since dma_pool_create() doesn't
allow NULL dev.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this udev doesn't have a way to key the ne device to the platform
device.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We mostly have pn533 fixes here, 2 memory leaks and an early unlocking fix.
Moreover, we also have an LLCP adapter linked list insertion fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+Jg
-----END PGP SIGNATURE-----
Merge tag 'nfc-fixes-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0
Samuel says:
"This is the first pull request for 3.7 NFC fixes.
We mostly have pn533 fixes here, 2 memory leaks and an early unlocking fix.
Moreover, we also have an LLCP adapter linked list insertion fix."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Intel 82855PM host bridge / Mobility FireGL 9000 RV250 combination
in an (outdated) ThinkPad T41 needs AGPMode 1 for suspend/resume (under
KMS, that is). So add a quirk for it.
(Change R250 to RV250 in comment for preceding quirk too.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The save struct is not initialized previously so explicitly
mark the crtcs as not used when they are not in use.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After the recent pile of disable-cloning patches, e.g.
commit e3b86d6941
Author: Egbert Eich <eich@suse.de>
Date: Sat Oct 13 14:30:15 2012 +0200
DRM/i915: Don't clone SDVO LVDS with analog
and a bug report from Chris Wilson indicating that cloning doesn't
even work for DVI-SDVO and native VGA, let's just disable cloning on
sdvo encoders completely.
v2: Update the comment in the code as discussed with Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29259
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After six and a half years of writing and maintaining KVM, it is time to
move to new things. Update my MAINTAINERS entry to reflect that.
Signed-off-by: Avi Kivity <avi@redhat.com>
In the absence of a physical reset line the chip is reset by writing the
first register, which is done after the register patch has been applied.
This patch synchronises the register cache after the reset to preserve
any register changes that had been applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the interrupt handler for an underclocked event, whilst checking for
the source of the interrupt, AIF3 was checked twice and AIF1 was not
checked. This change correctly checks the AIF1 underclocked bit and
reports the correct error messages for all cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm5102_devs array was used for ARRAY_SIZE whilst adding the wm5110
devices. This change corrects this to get the size from the wm5110_devs
array. As both arrays are the same size no issues should have been
caused by this bug.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Latest evaluation of the device has provided some revisions to the
configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 8214513 ("ARM: EXYNOS: fix address for EXYNOS4 MDMA1")
changed EXYNOS specific setup of PL330 DMA engine to use 'non-secure'
mdma1 address instead of 'secure' one (from 0x12840000 to 0x12850000)
to fix issue with some Exynos4212 SOCs. Unfortunately it brakes
PL330 setup for revision 0 of Exynos4210 SOC (mdma1 device cannot
be found at 'non-secure' address):
[ 0.566245] dma-pl330 dma-pl330.2: PERIPH_ID 0x0, PCELL_ID 0x0 !
[ 0.566278] dma-pl330: probe of dma-pl330.2 failed with error -22
Fix it by using 'secure' mdma1 address on Exynos4210 revision 0 SOC.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The correct chip id is 1 since the PWM module is on address 0x49. With the
current TWL6030_MODULE_ID1 the kernel will crash early since we have:
#define TWL6030_MODULE_ID1 0x0E
and
static struct twl_client twl_modules[4];
Down in the stack we try to get the module by:
struct twl_client *twl = &twl_modules[chip];
Which is obviously going to do nasty things.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
blkdev_issue_discard currently assumes that the granularity
is a power of 2. So in raid5, round the chosen number up to
avoid embarrassment.
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
md_stop() would stop an array, but not free various attached
data structures.
For internal arrays, these are freed later in do_md_stop() or
mddev_put(), but they don't apply for dm-raid arrays.
So get md_stop() to free them, and only all it from dm-raid.
For internal arrays we now call __md_stop.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If read_seqretry returned true and bbp was changed, it will write
invalid address which can cause some serious problem.
This bug was introduced by commit v3.0-rc7-130-g2699b67.
So fix is suitable for 3.0.y thru 3.6.y.
Reported-by: zhuwenfeng@kedacom.com
Tested-by: zhuwenfeng@kedacom.com
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced by commit(v3.0-rc7-126-g2230dfe).
So fix is suitable for 3.0.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In target mode, sent sk_buff were not freed in pn533_tm_send_complete
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd is allocated in pn533_dep_link_up and passed as an arg to
pn533_send_cmd_frame_async together with a complete cb.
arg is passed to the cb and must be kfreed there.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd was freed in pn533_dep_link_up regardless of
pn533_send_cmd_frame_async return code. Cmd is passed as argument to
pn533_in_dep_link_up_complete callback and should be freed there.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In pn533_wq_cmd command was removed from list without cmd_lock held
(race with pn533_send_cmd_frame_async) which could lead to list
corruption. Delete command from list before releasing lock.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
list_add was called with swapped parameters
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make perf build for x86 once the UAPI disintegration patches for that arch
have been applied by adding the appropriate -I flags - in the right order -
and then converting some #includes that use ../.. notation to find main kernel
headerfiles to use <asm/foo.h> and <linux/foo.h> instead.
Note that -Iarch/foo/include/uapi is present _before_ -Iarch/foo/include.
This makes sure we get the userspace version of the pt_regs struct. Ideally,
we wouldn't have the latter -I flag at all, but unfortunately we want
asm/svm.h and asm/vmx.h in builtin-kvm.c and these aren't part of the UAPI -
at least not for x86. I wonder if the bits outside of the __KERNEL__ guards
*should* be transferred there.
I note also that perf seems to do its dependency handling manually by listing
all the header files it might want to use in LIB_H in the Makefile. Can this
be changed to use -MD?
Note that to do make this work, we need to export and UAPI disintegrate
linux/hw_breakpoint.h, which I think should've been exported previously so that
perf can access the bits. We have to do this in the same patch to maintain
bisectability.
Signed-off-by: David Howells <dhowells@redhat.com>
Use the 'unistd.h' from arch/powerpc/include/uapi to build the perf tool.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20121107191818.GA16211@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fixing:
[acme@sandy linux]$ cd tools
[acme@sandy tools]$ make clean
DESCEND power/cpupower
CC lib/cpufreq.o
CC lib/sysfs.o
LD libcpupower.so.0.0.0
CC utils/helpers/amd.o
utils/helpers/amd.c:7:21: error: pci/pci.h: No such file or directory
In file included from utils/helpers/amd.c:9:
./utils/helpers/helpers.h:137: warning: ‘struct pci_access’ declared inside parameter list
./utils/helpers/helpers.h:137: warning: its scope is only this definition or declaration, which is probably not what you want
./utils/helpers/helpers.h:139: warning: ‘struct pci_access’ declared inside parameter list
utils/helpers/amd.c: In function ‘amd_pci_get_num_boost_states’:
utils/helpers/amd.c:120: warning: passing argument 1 of ‘pci_slot_func_init’ from incompatible pointer type
./utils/helpers/helpers.h:138: note: expected ‘struct pci_access **’ but argument is of type ‘struct pci_access **’
utils/helpers/amd.c:125: warning: implicit declaration of function ‘pci_read_byte’
utils/helpers/amd.c:132: warning: implicit declaration of function ‘pci_cleanup’
make[1]: *** [utils/helpers/amd.o] Error 1
make: *** [cpupower_clean] Error 2
[acme@sandy tools]$
Reported-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-tviyimq6x6nm77sj5lt4t19f@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Honour the O= flag that was passed to a higher level Makefile and then passed
down as part of a tool build.
To make this work, the top-level Makefile passes the original O= flag and
subdir=tools to the tools/Makefile, and that in turn passes
subdir=$(O)/$(subdir)/foodir when building tool foo in directory
$(O)/$(subdir)/foodir (where the intervening slashes aren't added if an
element is missing).
For example, take perf. This is found in tools/perf/. Assume we're building
into directory ~/zebra/, so we pass O=~/zebra to make. Dependening on where
we run the build from, we see:
make run in dir $(OUTPUT) dir
======================= ==================
linux ~/zebra/tools/perf/
linux/tools ~/zebra/perf/
linux/tools/perf ~/zebra/
and if O= is not set, we get:
make run in dir $(OUTPUT) dir
======================= ==================
linux linux/tools/perf/
linux/tools linux/tools/perf/
linux/tools/perf linux/tools/perf/
The output directories are created by the descend function if they don't
already exist.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1378.1352379110@warthog.procyon.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define a Makefile function that can be called with $(call ...) to wrap
the subdir make invocations in tools/Makefile.
This will allow us in the next patch to insert bits in there to honour
O= flags when called from the top-level Makefile.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1378.1352379110@warthog.procyon.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently if len argument in ext3_trim_fs() is smaller than one block,
the 'end' variable underflow. Avoid that by returning EINVAL if len is
smaller than file system block.
Also remove useless unlikely().
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Calls into highlevel quota code cannot happen under the write lock. These
calls take dqio_mutex which ranks above write lock. So drop write lock
before calling back into quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
Calls into reiserfs journalling code and reiserfs_get_block() need to
be protected with write lock. We remove write lock around calls to high
level quota code in the next patch so these paths would suddently become
unprotected.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
In reiserfs_quota_on() we do quite some work - for example unpacking
tail of a quota file. Thus we have to hold write lock until a moment
we call back into the quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
When remounting reiserfs dquot_suspend() or dquot_resume() can be called.
These functions take dqonoff_mutex which ranks above write lock so we have
to drop it before calling into quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
We've got a report that the runtime PM may make the codec the
unresponsive on AMD platforms. Since the feature has been tested only
on the recent Intel platforms, it's safer to limit the support to such
devices for now.
This patch adds a new DCAPS bit flag indicating the runtime PM
support, and mark it for Intel controllers.
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
