Check the value ranges in ctl put callbacks properly in the rest of
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch kills these two compilation warnings if
power management is disabled:
sound/pci/ac97/ac97_patch.h:86: warning: 'snd_ac97_restore_status'
declared 'static' but never defined
sound/pci/ac97/ac97_patch.h:87: warning: 'snd_ac97_restore_iec958'
declared 'static' but never defined
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
These patches enable a few YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The second one contains following changes:
- A chip-specific SPDIF support for YMF743 (It doesn't have AC97
standard SPDIF registers seen on YMF753).
- The implementation for 'IEC958 Playback Source' and 'IEC958 Mute'
are identical to the ones for YMF753. But there is no 'IEC958 Output
Pin' for YMF743.
Signed-off-by: Keita Maehara <maehara@debian.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
These patches enable some YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The first one contains only cosmetic changes to share a few
YMF753-specific symbols with YMF743.
Signed-off-by: Keita Maehara <maehara@debian.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT
Kconfig options as the default values for power-saving mode of AC97 and
HD-audio drivers, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
On codec chips with both audio and modem functions (e.g. Conexant one),
performing AC97_RESET resets the whole registers. When both audio and
modem drivers are resumed at the same time, the modem one often is
resumed after the audio, and it results in the reset of audio registers
(ALSA bug#3333).
This patch fixes such a problem. Since the modem codec basically
doesn't need AC97_RESET, skip this initialization unless specified
as audio.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Replace the direct calculation of jiffies with msecs_to_jiffies().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Included is a patch against current alsa-kernel hg tip adding
quirks that Ubuntu Dapper/Edgy/Feisty contains.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch provides a single 8 way enum called 'Smart 5.1 Select' with
some reasonable names for each enum that allows the user to choose
which of the 8 possible settings for vt1617a's version of what via
calls 'Smart 5.1'.
Signed-off-by: John Utz <john.utz@dmx.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Include ac97_patch.c from the main ac97_codec.c in order to make
bunch of patch_*() functions static. This helps optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes the control logic for shared
Microphone in/Center+LFE out and Line in/Surround out jacks
for Analog Devices AD1888, AD1980 and AD1985 AC '97 CODECs.
Signed-off-by: Randy Cushman <rcushman_linux@earthlink.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added Thinkpad X31 and R40 to AD1981x line/HP-jack-sense blacklist
for avoiding the harmful mixer controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed the silent output problem on laptops with Conexant Cx20551 codec
chip, such as Packard-bell EasyNote A* series.
The information was taken from ALSA bug#1134.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Remove delayed work properly at free and suspend in ac97 codec and
ak4114 drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Mark TLV data as 'const'
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch connects the extra vt1616 controls for the vt1617a, which
is necessary to control the rear speakers on e.g. a Shuttle SN25P.
Signed-off-by: Daniel Jacobowitz <drow@false.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Previously, ac97_codec.c was coded to support AD1986 and AD1986A
CODECs using code written for the AD1985 CODEC. This allowed the
LINE_OUT and HEADPHONE jacks to function properly, however register
differences between the CODECs prevented line and microphone inputs
from functioning.
Specifically, this patch fixes issues with the following mixer
controls: 'V_REFOUT', 'Spread Front to Surround and Center/LFE',
'Exchange Front/Surround', 'Surround Jack Mode', and 'Channel Mode'.
This patch removes the undocumented AD1888 control
'High Pass Filter Enable' and adds the new control
'Exchange Mic/Line In'.
Signed-off-by: Randy Cushman <rcushman_linux@earthlink.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch replaces the 'V_REFOUT Enable' mixer switch control
with a listbox control for the AD1985 CODEC.
Previous patch 'AD1888 mixer controls for DC mode' added
controls that were propogated to multiple codecs. For the
AD1985 codec, the bits VREFH and VREFD function differently,
preventing the 'V_REFOUT Enable' control from setting V_REFOUT
to Hi-Z.
This patch also corrects an issue in which register bits relating
to mixer controls 'Surround Jack Mode' and 'Channel Mode'.
The register bits controlled by these controls were being set
at boot time to states inconsistent with the stored values of
these controls.
Signed-off-by: Randy Cushman <rcushman_linux@earthlink.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes the Microphone and LINE_IN select logic for
Analog Devices surround codecs with shared jacks. The existing
code can never utilize the shared jacks for Microphone and LINE_IN
due to the reversed jack selection logic. The patched code
correctly selects the shared jack for input if the 'Channel Mode'
selector does not specify that the jack is to be used for output.
Specifically, in '2ch' mode the Center/LFE jack is used for
microphone input and the Surround jack is used for LINE_IN,
in '4ch' mode the Center/LFE jack is used for microphone input
and the Surround jack is used for output, and in '6ch' mode
both jacks are used for output.
Signed-off-by: Randy Cushman <rcushman_linux@earthlink.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The STAC9708/11 AC97 codecs implement the PCM Out Path & Mute bit in
the General Purpose register (0x20:F), even though they don't implement
the actual function in the mixer.
Since the alsa tests for the function by toggling the bit and reading
it back to see if it changed, it mistakenly creates a useless control.
This patch explicitly removes the control when the codec is an
STAC9708/11.
I put the check in patch_sigmatel_stac9708_specific(), because I have
an SBLive with this chip on it. I don't know if the STAC9758 or other
codecs also behave this way. If they do, then this check could maybe go
in patch_sigmatel_stac97xx_specific(), or some other more general
function.
Signed-off-by: James C Georgas <jgeorgas@rogers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't enable power-saving mode on drivers that don't support
it. The supporting drivers set AC97_SCAP_POWER_SAVE to scaps
at creation of ac97 instance.
Currently enable on the following drivers: intel8x0, intel8x0m,
atiixp, atiixp-modem, via82xx and via82xx-modem.
Also, a bit clean up of power-saving stuff:
- Don't create an own workq
- Remove superfluous ifdefs
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a couple of bit update functions in
alsa-kernel/pci/ac97/ac97_codec.c, which could possibly corrupt bits not
in the given mask.
Specifically, it'll clobber unset bits in the target that are not in the
mask, when the corresponding bit in the given new value is set.
Signed-off-by: James C Georgas <jgeorgas@rogers.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the case cidx2 >= 0 and cidx2 < 0 which may result in negative
array index.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Commit 2d4ba4a3b9 introduced a dependency
that was never meant to exist when the ac97_bus.c module was created.
Move ac97_bus.c up the directory hierarchy to make sure it is built when
selected even if sound is configured out so things work as originally
intended.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the bug in AC97 power-saving mode that the power isn't turned on
when power_save is set to 1 via sysfs during the power off state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Luke Zhang fixes a couple of issues with the WM9712
support in ac97_patch.c
Changes:-
o Fix Out3 ZC switch invert.
o Extend capture volume control to 6 bits.
o Change Mic 1 volume mask to 5 bits (31).
o Add Mic 2 volume.
Signed-off-by: Luke Zhang <lzhang@intrinsyc.com>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a build error (introduced by me) in ac97_patch.c wrt
WM9705 touchscreen.
o Removed spurious '3D' from character after |= operation (0x3D is
ASCII for '=')
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AD1819 volume registers can hold extra bits which do not affect the
actual volume. Add a res_table to the codec patch to fix the problem.
PCM, line and mic volume were tested.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the bad sound quality on VIA EPIA system using VIA VT1617A
(ALSA bug#2381).
Signed-off-by: Andrey Liakhovets <liakh@dol.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The attached patch will force building the S/PDIF controls on the PCU
SSID for Asus P5P800-VM motherboard, even if the AC97_EI_SPDIF bit is
not set.
Signed-off-by: Magnus Sandin <magnus@sandin.cx>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the TLV support to AC97 codec driver for addition of
dB range information.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Attached is the patch for the LG K1 Express (K1-2333V) laptop that
enables sound output.
Signed-off-by: Magnus Sandin <magnus@sandin.cx>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds some codec-specific controls for Philips UCB1400 codec.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added CONFIG_SND_AC97_POWER_SAVE kernel config to enable the support
of aggressive AC97 power-saving mode. In this mode, the AC97
powerdown register bits are dynamically controlled at each open/close
of PCM streams.
The mode is activated via power_save option for snd-ac97-codec
driver. As default it's off. It can be turned on/off on the fly
via sysfs, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Orignally proposed by Sam Revitch <sam.revitch@gmail.com>.
Unregister device files at disconnection to avoid the futher accesses.
Also, the dev_unregister callback is removed and replaced with the
combination of disconnect + free.
A new function snd_card_free_when_closed() is introduced, which is
used in USB disconnect callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Add the linked list to each proc entry to enable a single-shot
disconnection (unregister)
- Deprecate snd_info_unregister(), use snd_info_free_entry()
- Removed NULL checks of snd_info_free_entry()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Revert the mixer element names of some Mic controls to the state of
2.6.17. This should fix the name mismatch in alsactl.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds two mixer controls. The V_REFOUT enable is a
documented register that couples the microphone input lines
to the V_REFOUT DC source. The High Pass Filter enable in the
AC97_AD_TEST2 (0x5c) is an undocumented register provided by
Miller Puckette via Analog Devices that enables the AD codec
to apply a high pass filter to the input.
Signed-off-by: Jaya Kumar <jayakumar.alsa@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds a write to an undocumented register, 0x60 Extended
Codec Register Page in the AD1888 codec. It is neccessary in order
to make suspend/resume work with the AD1888.
Signed-off-by: Jaya Kumar <jayakumar.alsa@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch by Rodolfo Giometti disables the AC97 AUX and VIDEO controls
on the WM9705 when the touchscreen is selected as the AUX and VIDEO
lines are shared with the touch controller.
Changes:-
o Added AC97_HAS_NO_AUX flag
o Test for AC97_HAS_NO_AUX flag in snd_ac97_mixer_build()
o Sets AC97_HAS_NO_VIDEO and AC97_HAS_NO_AUX in patch_wolfson05() when
WM9705 touch driver is selected.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
