We used pnp_resource.index to keep track of which ISAPNP configuration
register a resource should be written to. We needed this only to
handle the case where a register is disabled but a subsequent register
in the same set is enabled.
Rather than explicitly maintaining the pnp_resource.index, this patch
adds a resource every time we read an ISAPNP configuration register
and marks the resource as IORESOURCE_DISABLED when appropriate. This
makes the position in the pnp_resource_table always correspond to the
config register index.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
In the debug resource dump, decode the flags and indicate when
a resource is disabled or has been automatically assigned.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When configuring the resources of an ACPI device, we first evaluate _CRS
to get a template of resource descriptors, then fill in the specific
resource values we want, and finally evaluate _SRS to actually configure
the device.
Some resources have optional fields, so the size of encoded descriptors
varies depending on the specific values. For example, IRQ descriptors can
be either two or three bytes long. The third byte contains triggering
information and can be omitted if the IRQ is edge-triggered and active
high.
The BIOS often assumes that IRQ descriptors in the _SRS buffer use the
same format as those in the _CRS buffer, so this patch enforces that
constraint.
The "Start Dependent Function" descriptor also has an optional byte, but
we don't currently encode those descriptors, so I didn't do anything for
those.
I have tested this patch on a Toshiba Portege 4000. Without the patch,
parport_pc claims the parallel port only if I use "pnpacpi=off". This
patch makes it work with PNPACPI.
This is an extension of a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c42
References:
http://bugzilla.kernel.org/show_bug.cgi?id=5832 Enabling ACPI Plug and Play in kernels >2.6.9 kills Parallel support
http://bugzilla.kernel.org/show_bug.cgi?id=9487 buggy firmware expects four-byte IRQ resource descriptor (was: Serial port disappears after Suspend on Toshiba R25)
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1d5b285da1893b90507b081664ac27f1a8a3dc5b related ACPICA fix
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When we encode IRQ resources, we should use the "shareable" flag we got
from _PRS rather than guessing based on the IRQ trigger mode.
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need to reserve "unset" resources. Trying to reserve
them results in messages like this, which are ugly but harmless:
system 00:08: iomem range 0x0-0x0 could not be reserved
Future PNP patches will remove use of IORESOURCE_UNSET, but
we still need it for now.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both the PNP/PCI conflict detection quirk and the PNP system
driver must use the same mechanism to mark resources as disabled.
I think it's best to keep the resource and to keep the type bit
(IORESOURCE_MEM, etc), so that we match the list from firmware
as closely as possible.
Fixes this regression from 2.6.25: http://lkml.org/lkml/2008/6/1/82
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Everybody wants to pass it a function pointer, and in fact, that is what
you _must_ pass it for it to make sense (since it knows that ia64 and
ppc64 use descriptors for function pointers and fetches the actual
address from there).
So don't make the argument be a 'unsigned long' and force everybody to
add a cast.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AD181x and AZT230 chips don't support an IRQ-less MPU401 option but
work fine without one. This adds (priority functional) IRQ-less options
for each port option to help systems with few available IRQs.
The AD1815 quirk can't use pnp_register_irq_resource() due to doubly
penalizing the IRQ. Also, while not a practical issue due to no IRQ
option being present for the dependents, this needs to add in front, not
back.
Doesn't use pnp_register_port_resource() for symetry with above.
This does not delete the AD1815 independent option even though it should
be empty after the IRQ transfer due to AD1816 coming with an empty but
still present independent option by default.
Was tested on AD1815, AD1816 and AZT2320. The ALSA snd-ad1818a driver
also support the AZT2002 ID for MPU401 but this doesn't as I was unable to
test it.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Len Brown <len.brown@intel.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The subsequent AD181x quirk patch would like this as part of the API.
pnp_register_dependent_option() adds to the same dependent chain the quirk is
walking which is fairly unclean. This enables a private option chain build
which it can then just add onto the end when done.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Len Brown <len.brown@intel.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it look a bit more like pci_fixup_device/pci_do_fixups. Also print
the PnP ID and delete the () from the "foo+0x0/0x1234()".
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Len Brown <len.brown@intel.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have to set the ISAPNP register index when setting an IRQ via the sysfs
interface. We already do it for IO, MEM, and DMA resources; I just missed the
IRQ one.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
next-20080430/drivers/pnp/pnpbios/rsparser.c:594: warning: format '%d' expects type 'int', but argument 4 has type 'resource_size_t'
next-20080430/drivers/pnp/pnpbios/rsparser.c:605: warning: format '%d' expects type 'int', but argument 4 has type 'resource_size_t'
[joe@perches.com: fix it]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x153d69): Section mismatch in reference from the function is_exclusive_device() to the variable .init.data:excluded_id_list
is_exclusive_device is only used from __init context so document
this with the __init annotation and get rid of the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_bus export and variable itself. Using pathnames works fine
and is slightly more understandable and greppable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The contents of include/linux/pnpbios.h are used only inside the PNPBIOS
backend, so this file doesn't need to be visible outside PNP.
This patch moves the contents into an existing PNPBIOS-specific file,
drivers/pnp/pnpbios/pnpbios.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The "regs" field in struct pnp_dev is set but never read, so remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The interfaces for registering protocols, devices, cards,
and resource options should only be used inside the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move warnings about _CRS and _PRS problems to the place where we
actually make the ACPI calls. Then we don't have to pass around
acpi_status values any more than necessary.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
isapnp_get_resources() does very little besides call
isapnp_read_resources(), so just fold them back together.
Based on a patch by Rene Herman <rene.herman@gmail.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a pnp_add_mem_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a pnp_add_io_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a pnp_add_dma_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a pnp_add_irq_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This encapsulates the code to locate a new pnp_resource of the
desired type. Currently this uses the pnp_resource_table, but
it will soon change to find a resource in a linked list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Save the ISAPNP config register index in the struct pnp_resource.
We need this because it is important to write ISAPNP configuration
back to the same registers we read it from. For example, if we
read valid regions from memory descriptors 0, 1, and 3, we'd
better write them back to the same registers, without compressing
them to descriptors 0, 1, and 2.
This was previously guaranteed by using the index into the
pnp_resource_table array as the ISAPNP config register index.
However, I am removing those fixed-size arrays, so we need to
save the ISAPNP register index elsewhere.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In some places, we need to get the struct pnp_resource, not just
the struct resource, because ISAPNP needs to store the register
index in the pnp_resource.
I don't like pnp_get_pnp_resource() and hope that it is temporary,
but we need it for a little while.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a "struct pnp_resource". This currently
contains only a struct resource, but we will soon need
additional PNP-specific information.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes a few more references to the pnp_resource_table.
No functional change.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There are no remaining references to the PNP_MAX_* constants or
the pnp_resource_table structure outside of the PNP core. Make
them private to the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove some PNP_MAX_* uses. The pnp_resource_table isn't
dynamic yet, but with pnp_get_resource(), we can start moving
away from the table size constants.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes more direct references to pnp_resource_table from the
pnp_assign_resources() path and the /sys user interface path.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes more direct references to pnp_resource_table. This
path is used when telling a device what resources it should use.
This doesn't convert ISAPNP because ISA needs to know the config
register index in addition to the resource itself.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes more direct references to pnp_resource_table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The caller already has the struct resource pointer, so no need for
pnp_check_port(), pnp_check_mem(), etc., to look it up again.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes a use of "idx" in pnp_check_port() and similar
functions, in preparation for replacing idx with a pointer to the
resource itself.
I split this out because it changes the behavior slightly: we used
to check for conflicts only with earlier resources, e.g., we checked
resource 2 against resources 0 and 1 but not against 3, 4, etc. Now
we will check against all resources except 2.
Since resources are assigned in ascending order, the old behavior
was probably safe, but I don't like to depend on that ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a temporary "res" pointer to replace repeated lookups in
the pnp resource tables.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a temporary "res" pointer to replace repeated lookups in
the pnp resource tables.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a temporary "res" pointer to replace repeated lookups in
the pnp resource tables.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cosmetic only: just use "i" instead of "tmp".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A future change will change pnp_mem_flags() from a "#define that
simplifies to an lvalue" to "an inline function that returns the
flags value."
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a pnp_get_resource() that works the same way as
platform_get_resource(). This will enable us to consolidate
many pnp_resource_table references in one place, which will
make it easier to make the table dynamic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the common part of pnp_init_resource_table() and
pnp_clean_resource_table() into a new pnp_init_resource().
This reduces a little code duplication and will be
useful later to initialize an individual resource.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use dev_printk() when possible for more informative error messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rene Herman <rene.herman@gmail.com> recently removed the only in-tree
driver uses of:
pnp_init_resource_table()
pnp_manual_config_dev()
pnp_resource_change()
in this change:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=109c53f840e551d6e99ecfd8b0131a968332c89f
These are no longer used in the PNP core either, so we can just remove
them completely.
It's possible that there are out-of-tree drivers that use these
interfaces. They should be changed to either (1) use PNP quirks
to work around broken hardware or firmware, or (2) use the sysfs
interfaces to control resource usage from userspace.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This changes pnp_clean_resource_table() to take a pnp_dev pointer
rather than a pnp_resource_table pointer. This reduces the visibility
of pnp_resource_table and removes an opportunity for error in the
caller.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add pnp_init_resources(struct pnp_dev *) to replace
pnp_init_resource_table(), which takes a pointer to the
pnp_resource_table itself. Passing only the pnp_dev * reduces
the possibility for error in the caller and removes the
pnp_resource_table implementation detail from the interface.
Even though pnp_init_resource_table() is exported, I did not
export pnp_init_resources() because it is used only by the PNP
core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds code to dump PNP resources before and after
assigning resources and before writing them to the device.
This is enabled by CONFIG_PNP_DEBUG=y.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add debug output to encoders (enabled by CONFIG_PNP_DEBUG). This
uses dev_printk, so I had to add pnp_dev arguments at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Stop passing around struct pnp_resource_table pointers. In most cases,
the caller doesn't need to know how the resources are stored inside
the struct pnp_dev.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When we call protocol->get() and protocol->set() methods, we currently
supply pointers to both the pnp_dev and the pnp_resource_table even
though the pnp_resource_table should always be the one associated with
the pnp_dev.
This removes the pnp_resource_table arguments to make it clear that
these methods only operate on the specified pnp_dev.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add debug output to resource option registration functions (enabled
by CONFIG_PNP_DEBUG). This uses dev_printk, so I had to add pnp_dev
arguments at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pass the pnp_dev pointer when possible instead of the acpi_handle.
This allows better error messages and reduces the chance of error
in the caller.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This simplifies IRQ resource parsing slightly by computing all the
IORESOURCE_IRQ_* flags at the same time.
This also keeps track of shareability information when parsing options
from _PRS. Previously we ignored shareability in _PRS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hoist dma_flags() out of pnpacpi_parse_allocated_dmaresource() into its
caller. This makes pnpacpi_parse_allocated_dmaresource() more similar
to pnpbios_parse_allocated_dmaresource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change, just fewer words and fewer chances for
transcription errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pnpacpi_encode_ext_irq() should set resource->data.extended_irq, not
resource->data.irq.
This has been wrong since at least 2.6.12. I haven't seen any bug
reports, but it's clearly incorrect.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add pnp_alloc_card() to allocate a struct pnp_card and fill in the
protocol, instance number, and initial PNP ID. Now it is always
valid to use dev_printk() on any pnp_card pointer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split the pnp_add_card_id() part from the PNPID conversion part so we
can move the initial add_id() into the pnp_card allocation.
This makes the PNPID conversion generic so we can use the same
one for both devices and cards.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This moves some of the pnp_id knowledge out of the backends and into
the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pnp_add_card_id() doesn't need to be exposed outside the PNP core, so
move the declaration to an internal header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add pnp_alloc_dev() to allocate a struct pnp_dev and fill in the
protocol, instance number, and initial PNP ID. Now it is always
valid to use dev_printk() on any pnp_dev pointer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Converting the EISA ID to a string is messy and error-prone, and
we might as well use the same code for ISAPNP and PNPBIOS.
PNPACPI uses the conversion done by the ACPI core with
acpi_ex_eisa_id_to_string().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This moves some of the pnp_id knowledge out of the backends and into
the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pnp_add_id() doesn't need to be exposed outside the PNP core, so
move the declaration to an internal header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Keep going and register the device even if we have trouble parsing
_CRS or _PRS. A parsing problem might mean we ignore some resources
the device is using, or we might not be able to change its resources.
But we should still take note of anything we *could* parse correctly.
Also remove reference to dev_id because I plan to remove it soon.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These are used only in drivers/pnp/isapnp/core.c, so no need to
expose them to the world.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Turn on -DDEBUG in CFLAGS when CONFIG_PNP_DEBUG=y. This makes
dev_dbg() do what you expect.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
print_fn_descriptor_symbol() prints the address if we don't have a symbol,
so no need to print both.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every PNP device should have a valid protocol pointer. If it doesn't,
something's wrong and we should oops so we can find and fix the problem.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PNP_MAX_IRQ is 2
If a device invokes pnpacpi_parse_allocated_irqresource() 0, 1, or 2 times, we are happy.
The 3rd time, we will fail and print "pnpacpi: exceeded the max number of IRQ resources: 2"
The 4th and subsequent calls (if this ever happened) would silently scribble on
irq_resource[2], which doesn't actualy exist.
Found-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have been printing these messages at KERN_ERR since 2.6.24,
per http://bugzilla.kernel.org/show_bug.cgi?id=9535
But KERN_ERR pops up on a console booted with "quiet"
and causes users to get alarmed and file bugs
about the message itself:
https://bugzilla.redhat.com/show_bug.cgi?id=436589
So reduce the severity of these messages to
KERN_WARNING, which is not printed by "quiet".
This message will still be seen without "quiet",
but a lot of messages are printed in that mode
and it will be less likely to cause undue alarm.
We could go all the way to KERN_DEBUG, but this
is a real warning after all, so it seems prudent
not to require "debug" to see it.
Signed-off-by: Len Brown <len.brown@intel.com>
PNP_MAX_MEM and PNP_MAX_PORT are mainly used to size tables of PNP
device resources. In 2.6.24, we increased their values to accomodate
ACPI devices that have many resources:
2.6.23 2.6.24
------ ------
PNP_MAX_MEM 4 12
PNP_MAX_PORT 8 40
However, ISAPNP also used these constants as the size of parts of the
logical device register set. This register set is fixed by hardware,
so increasing the constants meant that we were reading and writing
unintended parts of the register set.
This patch changes ISAPNP to use the correct register set sizes (the
same values we used prior to 2.6.24).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some BIOSes have PNP motherboard devices with resources that
partially overlap PCI BARs. The PNP system driver claims these
motherboard resources, which prevents the normal PCI driver from
requesting them later.
This patch disables the PNP resources that conflict with PCI BARs
so they won't be claimed by the PNP system driver.
Of course, this only works if PCI devices have already been enumerated.
Currently this is the case because PCI devices are discovered before
any PNP init via this path:
acpi_pci_root_init() -> acpi_pci_root_add() -> pci_acpi_scan_root() ->
pci_scan_bus_parented() -> pci_scan_child_bus() -> ...
Avuton Olrich tested this and confirmed that it fixes his ALSA sound
card (see http://lkml.org/lkml/2008/1/27/168).
References:
https://bugzilla.redhat.com/show_bug.cgi?id=280641https://bugzilla.redhat.com/show_bug.cgi?id=313491http://lkml.org/lkml/2008/1/9/449http://thread.gmane.org/gmane.linux.acpi.devel/27312http://lkml.org/lkml/2008/1/27/168
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are other systems with similar problems
(http://lkml.org/lkml/2008/1/27/168), so we need a more
generic quirk. Remove the Supermicro-specific one first.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: DMI: quirk for FSC ESPRIMO Mobile V5505
ACPI: DMI blacklist updates
pnpacpi: __initdata is not an identifier
ACPI: static acpi_chain_head
ACPI: static acpi_find_dsdt_initrd()
ACPI: static acpi_no_initrd_override_setup()
thinkpad_acpi: static
ACPI suspend: Execute _WAK with the right argument
cpuidle: Add Documentation
ACPI, cpuidle: Clarify C-state description in sysfs
ACPI: fix suspend regression due to idle update
The sound drivers and the pnpbios core test for current->root != NULL. This
test seems to be unnecessary since we always have rootfs mounted before
initializing the drivers.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse complains at drivers/pnp/pnpacpi/core.c:39 with the error:
Trying to use reserved word '__attribute__' as identifier
Expected ) in function declarator, got ".init.data"
and at drivers/pnp/pnpacpi/core.c:49:38 with the error:
undefined identifier 'excluded_id_list'
With the patch below these sparse complaints do not occur
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Some Supermicro BIOSes describe a SATA PCI BAR as a motherboard resource.
The PNP system driver claims motherboard resources, and this prevents the
sata_nv driver from requesting it later.
This patch disables the PNP0C01/PNP0C02 resources so they won't be claimed
by the PNP system driver, so they'll available for sata_nv.
This fixes the bugs below, where sata_nv detects only two out of four SATA
drives. The signature includes dmesg lines similar to these:
pnp: 00:09: iomem range 0xdfefc000-0xdfefcfff has been reserved
pnp: 00:09: iomem range 0xdfefd000-0xdfefd3ff has been reserved
pnp: 00:09: iomem range 0xdfefe000-0xdfefe3ff has been reserved
PCI: Unable to reserve mem region #6:1000@dfefd000 for device 0000:80:07.0
sata_nv: probe of 0000:80:07.0 failed with error -16
PCI: Unable to reserve mem region #6:1000@dfefe000 for device 0000:80:08.0
sata_nv: probe of 0000:80:08.0 failed with error -16
References:
https://bugzilla.redhat.com/show_bug.cgi?id=280641https://bugzilla.redhat.com/show_bug.cgi?id=313491http://lkml.org/lkml/2008/1/9/449http://thread.gmane.org/gmane.linux.acpi.devel/27312
This is post-2.6.24 material.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PNP_DRIVER_RES_DO_NOT_CHANGE flag is meant to signify that the PNP core
should not change resources for the device -- not that it shouldn't
disable/enable the device on suspend/resume.
ALSA ISAPnP drivers set PNP_DRIVER_RES_DO_NOT_CHANAGE (0x0001) through
setting PNP_DRIVER_RES_DISABLE (0x0003). The latter including the former
may in itself be considered rather unexpected but doesn't change that
suspend/resume wouldn't seem to have any business testing the flag.
As reported by Ondrej Zary for snd-cs4236, ALSA driven ISAPnP cards don't
survive swsusp hibernation with the resume skipping setting the resources
due to testing the flag -- the same test in the suspend path isn't enough
to keep hibernation from disabling the card it seems.
These tests were added (in 2005) by Piere Ossman in commit
68094e3251, "alsa: Improved PnP suspend
support" who doesn't remember why. This deletes them.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are three kind of parse functions provided by PNP acpi/bios:
- get current resources
- set resources
- get possible resources
The first two may be needed later at runtime.
The possible resource settings should never change dynamically.
And even if this would make any sense (I doubt it), the current implementation
only parses possible resource settings at early init time:
-> declare all the option parsing __init
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-By: Rene Herman <rene.herman@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make pnp_activate_dev() and pnp_disable_dev() return only 0 (success) or a
negative error value, as pci_enable_device() and pci_disable_device() do.
Previously they returned:
0: device was already active (or disabled)
1: we just activated (or disabled) device
<0: -EBUSY or error from pnp_start_dev() (or pnp_stop_dev())
Now we return only 0 (device is active or disabled) or <0 (error).
All in-tree callers either ignore the return values or check only for
errors (negative values).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wups, previous patch was ineffective in 2 cases.
http://bugzilla.kernel.org/show_bug.cgi?id=9535
Signed-off-by: Len Brown <len.brown@intel.com>
Reported-by: "Hartkopp, Oliver (K-EFE/E)" <oliver.hartkopp@volkswagen.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PNP_WRITE requires protocol supports .set. If ACPI doesn't support _SRS, .set ismeanless, so PNP_WRITE.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pnpacpi: exceeded the max number of IO resources: 40
While this message is a real error and should thus
remain KERN_ERR (even a new dmesg line is seen as a regression
by some, since it was not printed in 2.6.23...) it is certainly
impolite to print this warning 50 times should you happen to
have the oddball system with 90 io resources under a device...
So print the warning just once.
In 2.6.25 we'll get rid of the limits altogether
and these warnings will vanish with them.
http://bugzilla.kernel.org/show_bug.cgi?id=9535
Signed-off-by: Len Brown <len.brown@intel.com>
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
This was fixed using the following semantic patch.
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@
T *d;
...
for_each_pci_dev(d)
{... when != pci_dev_put(d)
when != e = d
(
return d;
|
+ pci_dev_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Greg KH <greg@kroah.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some systems the number of resources(IO,MEM) returnedy by PNP device is
greater than the PNP constant, for example motherboard devices. It brings
that some resources can't be reserved and resource confilicts. This will
cause PCI resources are assigned wrongly in some systems, and cause hang.
This is a regression since we deleted ACPI motherboard driver and use PNP
system driver.
[akpm@linux-foundation.org: fix text and coding-style a bit]
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PNP debug message when adding a device, remove similar PNPACPI message
with less information.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hoist the struct pnp_dev alloc up into the function where it's used.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
