This patch correct a bug in the delay of pktgen.
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen_kill_estimator() / gen_new_estimator() is not always called with
RTNL held.
net/netfilter/xt_RATEEST.c is one user of these API that do not hold
RTNL, so random corruptions can occur between "tc" and "iptables".
Add a new fine grained lock instead of trying to use RTNL in netfilter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/591416
There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.
Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
If a skb is received on an inactive bond that does not meet
the special cases checked for by skb_bond_should_drop it should
only be delivered to exact matches as the comment in
netif_receive_skb() says.
However because null_or_bond could also be null this is not
always true. This patch renames null_or_bond to orig_or_bond
and initializes it to orig_dev. This keeps the intent of
null_or_bond to pass frames received on VLAN interfaces stacked
on bonding interfaces without invalidating the statement for
null_or_orig.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct sk_forward_alloc handling for error_queue would need to use a
backlog of frames that softirq handler could not deliver because socket
is owned by user thread. Or extend backlog processing to be able to
process normal and error packets.
Another possibility is to not use mem charge for error queue, this is
what I implemented in this patch.
Note: this reverts commit 29030374
(net: fix sk_forward_alloc corruptions), since we dont need to lock
socket anymore.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David found out, sock_queue_err_skb() should be called with socket
lock hold, or we risk sk_forward_alloc corruption, since we use non
atomic operations to update this field.
This patch adds bh_lock_sock()/bh_unlock_sock() pair to three spots.
(BH already disabled)
1) skb_tstamp_tx()
2) Before calling ip_icmp_error(), in __udp4_lib_err()
3) Before calling ipv6_icmp_error(), in __udp6_lib_err()
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
netlink: bug fix: wrong size was calculated for vfinfo list blob
netlink: bug fix: don't overrun skbs on vf_port dump
xt_tee: use skb_dst_drop()
netdev/fec: fix ifconfig eth0 down hang issue
cnic: Fix context memory init. on 5709.
drivers/net: Eliminate a NULL pointer dereference
drivers/net/hamradio: Eliminate a NULL pointer dereference
be2net: Patch removes redundant while statement in loop.
ipv6: Add GSO support on forwarding path
net: fix __neigh_event_send()
vhost: fix the memory leak which will happen when memory_access_ok fails
vhost-net: fix to check the return value of copy_to/from_user() correctly
vhost: fix to check the return value of copy_to/from_user() correctly
vhost: Fix host panic if ioctl called with wrong index
net: fix lock_sock_bh/unlock_sock_bh
net/iucv: Add missing spin_unlock
net: ll_temac: fix checksum offload logic
net: ll_temac: fix interrupt bug when interrupt 0 is used
sctp: dubious bitfields in sctp_transport
ipmr: off by one in __ipmr_fill_mroute()
...
The wrong size was being calculated for vfinfo. In one case, it was over-
calculating using nlmsg_total_size on attrs, in another case, it was
under-calculating by assuming ifla_vf_* structs are packed together, but
each struct is it's own attr w/ hdr (and padding).
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Patrick McHardy: was continuing to fill skb after a
nla_put_failure, ignoring the size calculated by upper layer. Now,
return -EMSGSIZE on any overruns, but also allow netdev to
fail ndo_get_vf_port with error other than -EMSGSIZE, thus unwinding
nest.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7fee226ad2 (net: add a noref bit on skb dst) missed one spot
where an skb is enqueued, with a possibly not refcounted dst entry.
__neigh_event_send() inserts skb into arp_queue, so we must make sure
dst entry is refcounted, or dst entry can be freed by garbage collector
after caller exits from rcu protected section.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
tracing: Add __used annotation to event variable
perf, trace: Fix !x86 build bug
perf report: Support multiple events on the TUI
perf annotate: Fix up usage of the build id cache
x86/mmiotrace: Remove redundant instruction prefix checks
perf annotate: Add TUI interface
perf tui: Remove annotate from popup menu after failure
perf report: Don't start the TUI if -D is used
perf: Fix getline undeclared
perf: Optimize perf_tp_event_match()
perf: Remove more code from the fastpath
perf: Optimize the !vmalloc backed buffer
perf: Optimize perf_output_copy()
perf: Fix wakeup storm for RO mmap()s
perf-record: Share per-cpu buffers
perf-record: Remove -M
perf: Ensure that IOC_OUTPUT isn't used to create multi-writer buffers
perf, trace: Optimize tracepoints by using per-tracepoint-per-cpu hlist to track events
perf, trace: Optimize tracepoints by removing IRQ-disable from perf/tracepoint interaction
perf tui: Allow disabling the TUI on a per command basis in ~/.perfconfig
...
This new sock lock primitive was introduced to speedup some user context
socket manipulation. But it is unsafe to protect two threads, one using
regular lock_sock/release_sock, one using lock_sock_bh/unlock_sock_bh
This patch changes lock_sock_bh to be careful against 'owned' state.
If owned is found to be set, we must take the slow path.
lock_sock_bh() now returns a boolean to say if the slow path was taken,
and this boolean is used at unlock_sock_bh time to call the appropriate
unlock function.
After this change, BH are either disabled or enabled during the
lock_sock_bh/unlock_sock_bh protected section. This might be misleading,
so we rename these functions to lock_sock_fast()/unlock_sock_fast().
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
drivers/net/usb/asix.c: Fix pointer cast.
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
proc_dointvec: write a single value
hso: add support for new products
Phonet: fix potential use-after-free in pep_sock_close()
ath9k: remove VEOL support for ad-hoc
ath9k: change beacon allocation to prefer the first beacon slot
sock.h: fix kernel-doc warning
cls_cgroup: Fix build error when built-in
macvlan: do proper cleanup in macvlan_common_newlink() V2
be2net: Bug fix in init code in probe
net/dccp: expansion of error code size
ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
wireless: fix sta_info.h kernel-doc warnings
wireless: fix mac80211.h kernel-doc warnings
iwlwifi: testing the wrong variable in iwl_add_bssid_station()
ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
ath9k_htc: dereferencing before check in hif_usb_tx_cb()
rt2x00: Fix rt2800usb TX descriptor writing.
rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
...
This patch makes tun update its socket classid every time we
inject a packet into the network stack. This is so that any
updates made by the admin to the process writing packets to
tun is effected.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now cls_cgroup has relied on fetching the classid out of
the current executing thread. This runs into trouble when a packet
processing is delayed in which case it may execute out of another
thread's context.
Furthermore, even when a packet is not delayed we may fail to
classify it if soft IRQs have been disabled, because this scenario
is indistinguishable from one where a packet unrelated to the
current thread is processed by a real soft IRQ.
In fact, the current semantics is inherently broken, as a single
skb may be constructed out of the writes of two different tasks.
A different manifestation of this problem is when the TCP stack
transmits in response of an incoming ACK. This is currently
unclassified.
As we already have a concept of packet ownership for accounting
purposes in the skb->sk pointer, this is a natural place to store
the classid in a persistent manner.
This patch adds the cls_cgroup classid in struct sock, filling up
an existing hole on 64-bit :)
The value is set at socket creation time. So all sockets created
via socket(2) automatically gains the ID of the thread creating it.
Whenever another process touches the socket by either reading or
writing to it, we will change the socket classid to that of the
process if it has a valid (non-zero) classid.
For sockets created on inbound connections through accept(2), we
inherit the classid of the original listening socket through
sk_clone, possibly preceding the actual accept(2) call.
In order to minimise risks, I have not made this the authoritative
classid. For now it is only used as a backup when we execute
with soft IRQs disabled. Once we're completely happy with its
semantics we can use it as the sole classid.
Footnote: I have rearranged the error path on cls_group module
creation. If we didn't do this, then there is a window where
someone could create a tc rule using cls_group before the cgroup
subsystem has been registered.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
the commit:
commit d90310243f
Author: Octavian Purdila <opurdila@ixiacom.com>
Date: Wed Nov 18 02:36:59 2009 +0000
net: device name allocation cleanups
introduced a bug when there is a hash collision making impossible
to rename a device with eth%d. This bug is very hard to reproduce
and appears rarely.
The problem is coming from we don't pass a temporary buffer to
__dev_alloc_name but 'dev->name' which is modified by the function.
A detailed explanation is here:
http://marc.info/?l=linux-netdev&m=127417784011987&w=2
Changelog:
V2 : replaced strings comparison by pointers comparison
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c02db8c629:
Author: Chris Wright <chrisw@sous-sol.org>
Date: Sun May 16 01:05:45 2010 -0700
Subject: rtnetlink: make SR-IOV VF interface symmetric
adds broken error handling to do_setlink() in net/core/rtnetlink.c. The
problem is the following chunk of code:
if (tb[IFLA_VFINFO_LIST]) {
struct nlattr *attr;
int rem;
nla_for_each_nested(attr, tb[IFLA_VFINFO_LIST], rem) {
if (nla_type(attr) != IFLA_VF_INFO)
----> goto errout;
err = do_setvfinfo(dev, attr);
if (err < 0)
goto errout;
modified = 1;
}
}
which can get to errout without setting err, resulting in the following error:
net/core/rtnetlink.c: In function 'do_setlink':
net/core/rtnetlink.c:904: warning: 'err' may be used uninitialized in this function
Change the code to return -EINVAL in this case. Note that this might not be
the appropriate error though.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Chris Wright <chrisw@sous-sol.org>
cc: David S. Miller <davem@davemloft.net>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds F_GETPIPE_SZ and F_SETPIPE_SZ fcntl() actions for
growing and shrinking the size of a pipe and adjusts pipe.c and splice.c
(and relay and network splice) usage to work with these larger (or smaller)
pipes.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This reverts commit aaf8cdc34d.
Drivers like the ipw2100 call device_create_group when they
are initialized and device_remove_group when they are shutdown.
Moving them between namespaces deletes their sysfs groups early.
In particular the following call chain results.
netdev_unregister_kobject -> device_del -> kobject_del -> sysfs_remove_dir
With sysfs_remove_dir recursively deleting all of it's subdirectories,
and nothing adding them back.
Ouch!
Therefore we need to call something that ultimate calls sysfs_mv_dir
as that sysfs function can move sysfs directories between namespaces
without deleting their subdirectories or their contents. Allowing
us to avoid placing extra boiler plate into every driver that does
something interesting with sysfs.
Currently the function that provides that capability is device_rename.
That is the code works without nasty side effects as originally written.
So remove the misguided fix for moving devices between namespaces. The
bug in the kobject layer that inspired it has now been recognized and
fixed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I had a couple of stupid bugs in:
netns: Teach network device kobjects which namespace they are in.
- I duplicated the Kconfig for the NET_NS
- The build was broken when sysfs was not compiled in
The sysfs breakage is because after I moved the operations
for the sysfs to the kobject layer, to make things cleaner
I forgot to move the ifdefs. Opps.
I'm not quite certain how I got introduced a second NET_NS Kconfig,
but it was probably a 3 way merge somewhere along the way that
did not notice that the NET_NS Kconfig option had mvoed and thout
that was a bug. It probably slipped in because it used to be the
sysfs patches were the first patches in my network namespace patches.
Some things just don't go like you would expect.
Neither of these bugs actually affect anything in the common case
but they should be fixed.
Thanks to Serge for noticing they were present.
Reported-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
The problem. Network devices show up in sysfs and with the network
namespace active multiple devices with the same name can show up in
the same directory, ouch!
To avoid that problem and allow existing applications in network namespaces
to see the same interface that is currently presented in sysfs, this
patch enables the tagging directory support in sysfs.
By using the network namespace pointers as tags to separate out the
the sysfs directory entries we ensure that we don't have conflicts
in the directories and applications only see a limited set of
the network devices.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called. This is needed for the mechanism
to prevent OOO packet in RFS. Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.
Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct. The correct value
would be head+input_pkt_queue->len+process_queue->len. To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.
This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.
This patch fixes that.
Reported-by: Igor Zhang <yugzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new netdev ops ndo_{set|get}_vf_port to allow setting of
port-profile on a netdev interface. Extends netlink socket RTM_SETLINK/
RTM_GETLINK with two new sub msgs called IFLA_VF_PORTS and IFLA_PORT_SELF
(added to end of IFLA_cmd list). These are both nested atrtibutes
using this layout:
[IFLA_NUM_VF]
[IFLA_VF_PORTS]
[IFLA_VF_PORT]
[IFLA_PORT_*], ...
[IFLA_VF_PORT]
[IFLA_PORT_*], ...
...
[IFLA_PORT_SELF]
[IFLA_PORT_*], ...
These attributes are design to be set and get symmetrically. VF_PORTS
is a list of VF_PORTs, one for each VF, when dealing with an SR-IOV
device. PORT_SELF is for the PF of the SR-IOV device, in case it wants
to also have a port-profile, or for the case where the VF==PF, like in
enic patch 2/2 of this patch set.
A port-profile is used to configure/enable the external switch virtual port
backing the netdev interface, not to configure the host-facing side of the
netdev. A port-profile is an identifier known to the switch. How port-
profiles are installed on the switch or how available port-profiles are
made know to the host is outside the scope of this patch.
There are two types of port-profiles specs in the netlink msg. The first spec
is for 802.1Qbg (pre-)standard, VDP protocol. The second spec is for devices
that run a similar protocol as VDP but in firmware, thus hiding the protocol
details. In either case, the specs have much in common and makes sense to
define the netlink msg as the union of the two specs. For example, both specs
have a notition of associating/deassociating a port-profile. And both specs
require some information from the hypervisor manager, such as client port
instance ID.
The general flow is the port-profile is applied to a host netdev interface
using RTM_SETLINK, the receiver of the RTM_SETLINK msg communicates with the
switch, and the switch virtual port backing the host netdev interface is
configured/enabled based on the settings defined by the port-profile. What
those settings comprise, and how those settings are managed is again
outside the scope of this patch, since this patch only deals with the
first step in the flow.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SMP=y, then we own a queue spinlock, we can avoid the atomic
test_and_set_bit() from napi_schedule_prep().
We now have same number of atomic ops per netif_rx() calls than with
pre-RPS kernel.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have a set of nested attributes:
IFLA_VFINFO_LIST (NESTED)
IFLA_VF_INFO (NESTED)
IFLA_VF_MAC
IFLA_VF_VLAN
IFLA_VF_TX_RATE
This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.
The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the
sk->sk_route_caps &= ~NETIF_F_GSO_MASK
that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)
So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.
Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds data to be passed to tracepoint callbacks.
The created functions from DECLARE_TRACE() now need a mandatory data
parameter. For example:
DECLARE_TRACE(mytracepoint, int value, value)
Will create the register function:
int register_trace_mytracepoint((void(*)(void *data, int value))probe,
void *data);
As the first argument, all callbacks (probes) must take a (void *data)
parameter. So a callback for the above tracepoint will look like:
void myprobe(void *data, int value)
{
}
The callback may choose to ignore the data parameter.
This change allows callbacks to register a private data pointer along
with the function probe.
void mycallback(void *data, int value);
register_trace_mytracepoint(mycallback, mydata);
Then the mycallback() will receive the "mydata" as the first parameter
before the args.
A more detailed example:
DECLARE_TRACE(mytracepoint, TP_PROTO(int status), TP_ARGS(status));
/* In the C file */
DEFINE_TRACE(mytracepoint, TP_PROTO(int status), TP_ARGS(status));
[...]
trace_mytracepoint(status);
/* In a file registering this tracepoint */
int my_callback(void *data, int status)
{
struct my_struct my_data = data;
[...]
}
[...]
my_data = kmalloc(sizeof(*my_data), GFP_KERNEL);
init_my_data(my_data);
register_trace_mytracepoint(my_callback, my_data);
The same callback can also be registered to the same tracepoint as long
as the data registered is different. Note, the data must also be used
to unregister the callback:
unregister_trace_mytracepoint(my_callback, my_data);
Because of the data parameter, tracepoints declared this way can not have
no args. That is:
DECLARE_TRACE(mytracepoint, TP_PROTO(void), TP_ARGS());
will cause an error.
If no arguments are needed, a new macro can be used instead:
DECLARE_TRACE_NOARGS(mytracepoint);
Since there are no arguments, the proto and args fields are left out.
This is part of a series to make the tracepoint footprint smaller:
text data bss dec hex filename
4913961 1088356 861512 6863829 68bbd5 vmlinux.orig
4914025 1088868 861512 6864405 68be15 vmlinux.class
4918492 1084612 861512 6864616 68bee8 vmlinux.tracepoint
Again, this patch also increases the size of the kernel, but
lays the ground work for decreasing it.
v5: Fixed net/core/drop_monitor.c to handle these updates.
v4: Moved the DECLARE_TRACE() DECLARE_TRACE_NOARGS out of the
#ifdef CONFIG_TRACE_POINTS, since the two are the same in both
cases. The __DECLARE_TRACE() is what changes.
Thanks to Frederic Weisbecker for pointing this out.
v3: Made all register_* functions require data to be passed and
all callbacks to take a void * parameter as its first argument.
This makes the calling functions comply with C standards.
Also added more comments to the modifications of DECLARE_TRACE().
v2: Made the DECLARE_TRACE() have the ability to pass arguments
and added a new DECLARE_TRACE_NOARGS() for tracepoints that
do not need any arguments.
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Introduce ____napi_schedule() helper for callers in irq disabled
contexts. rps_trigger_softirq() becomes a leaf function.
Use container_of() in process_backlog() instead of accessing per_cpu
address.
Use a custom inlined version of __napi_complete() in process_backlog()
to avoid one locked instruction :
only current cpu owns and manipulates this napi,
and NAPI_STATE_SCHED is the only possible flag set on backlog.
we can use a plain write instead of clear_bit(),
and we dont need an smp_mb() memory barrier, since RPS is on,
backlog is protected by a spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of congestion, netif_rx() frees the skb, so we must assume
dev_forward_skb() also consume skb.
Bug introduced by commit 445409602c
(veth: move loopback logic to common location)
We must change dev_forward_skb() to always consume skb, and veth to not
double free it.
Bug report : http://marc.info/?l=linux-netdev&m=127310770900442&w=3
Reported-by: Martín Ferrari <martin.ferrari@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This whole patchset is for adding netpoll support to bridge and bonding
devices. I already tested it for bridge, bonding, bridge over bonding,
and bonding over bridge. It looks fine now.
To make bridge and bonding support netpoll, we need to adjust
some netpoll generic code. This patch does the following things:
1) introduce two new priv_flags for struct net_device:
IFF_IN_NETPOLL which identifies we are processing a netpoll;
IFF_DISABLE_NETPOLL is used to disable netpoll support for a device
at run-time;
2) introduce one new method for netdev_ops:
->ndo_netpoll_cleanup() is used to clean up netpoll when a device is
removed.
3) introduce netpoll_poll_dev() which takes a struct net_device * parameter;
export netpoll_send_skb() and netpoll_poll_dev() which will be used later;
4) hide a pointer to struct netpoll in struct netpoll_info, ditto.
5) introduce ->real_dev for struct netpoll.
6) introduce a new status NETDEV_BONDING_DESLAE, which is used to disable
netconsole before releasing a slave, to avoid deadlocks.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With following patch I can reach maximum rate of my pktgen+udpsink
simulator :
- 'old' machine : dual quad core E5450 @3.00GHz
- 64 UDP rx flows (only differ by destination port)
- RPS enabled, NIC interrupts serviced on cpu0
- rps dispatched on 7 other cores. (~130.000 IPI per second)
- SLAB allocator (faster than SLUB in this workload)
- tg3 NIC
- 1.080.000 pps without a single drop at NIC level.
Idea is to add two prefetchw() calls in __alloc_skb(), one to prefetch
first sk_buff cache line, the second to prefetch the shinfo part.
Also using one memset() to initialize all skb_shared_info fields instead
of one by one to reduce number of instructions, using long word moves.
All skb_shared_info fields before 'dataref' are cleared in
__alloc_skb().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4b0b72f7dd ( net: speedup udp receive path )
introduced a bug in skb_free_datagram_locked().
We should not skb_orphan() skb if we dont have the guarantee we are the
last skb user, this might happen with MSG_PEEK concurrent users.
To keep socket locked for the smallest period of time, we split
consume_skb() logic, inlined in skb_free_datagram_locked()
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per cpu variable softnet_data.total was shared between IRQ and SoftIRQ context
without any protection. And enqueue_to_backlog should update the netdev_rx_stat
of the target CPU.
This patch renames softnet_data.total to softnet_data.processed: the number of
packets processed in uppper levels(IP stacks).
softnet_stat data is moved into softnet_data.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
include/linux/netdevice.h | 17 +++++++----------
net/core/dev.c | 26 ++++++++++++--------------
net/sched/sch_generic.c | 2 +-
3 files changed, 20 insertions(+), 25 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6be8ac2f ("[NET]: uninline skb_pull, de-bloats a lot")
we uninlined skb_pull.
But in some critical paths it makes sense to inline this thing
and it helps performance significantly.
Create an skb_pull_inline() so that we can do this in a way that
serves also as annotation.
Based upon a patch by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_callback_lock rwlock actually protects sk->sk_sleep pointer, so we
need two atomic operations (and associated dirtying) per incoming
packet.
RCU conversion is pretty much needed :
1) Add a new structure, called "struct socket_wq" to hold all fields
that will need rcu_read_lock() protection (currently: a
wait_queue_head_t and a struct fasync_struct pointer).
[Future patch will add a list anchor for wakeup coalescing]
2) Attach one of such structure to each "struct socket" created in
sock_alloc_inode().
3) Respect RCU grace period when freeing a "struct socket_wq"
4) Change sk_sleep pointer in "struct sock" by sk_wq, pointer to "struct
socket_wq"
5) Change sk_sleep() function to use new sk->sk_wq instead of
sk->sk_sleep
6) Change sk_has_sleeper() to wq_has_sleeper() that must be used inside
a rcu_read_lock() section.
7) Change all sk_has_sleeper() callers to :
- Use rcu_read_lock() instead of read_lock(&sk->sk_callback_lock)
- Use wq_has_sleeper() to eventually wakeup tasks.
- Use rcu_read_unlock() instead of read_unlock(&sk->sk_callback_lock)
8) sock_wake_async() is modified to use rcu protection as well.
9) Exceptions :
macvtap, drivers/net/tun.c, af_unix use integrated "struct socket_wq"
instead of dynamically allocated ones. They dont need rcu freeing.
Some cleanups or followups are probably needed, (possible
sk_callback_lock conversion to a spinlock for example...).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 95766fff ([UDP]: Add memory accounting.),
each received packet needs one extra sock_lock()/sock_release() pair.
This added latency because of possible backlog handling. Then later,
ticket spinlocks added yet another latency source in case of DDOS.
This patch introduces lock_sock_bh() and unlock_sock_bh()
synchronization primitives, avoiding one atomic operation and backlog
processing.
skb_free_datagram_locked() uses them instead of full blown
lock_sock()/release_sock(). skb is orphaned inside locked section for
proper socket memory reclaim, and finally freed outside of it.
UDP receive path now take the socket spinlock only once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there's no need to use this fuction directly because it's handled by
register_pernet_device. So to make this simple and easy to understand,
make this static to do not tempt potentional users.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current socket backlog limit is not enough to really stop DDOS attacks,
because user thread spend many time to process a full backlog each
round, and user might crazy spin on socket lock.
We should add backlog size and receive_queue size (aka rmem_alloc) to
pace writers, and let user run without being slow down too much.
Introduce a sk_rcvqueues_full() helper, to avoid taking socket lock in
stress situations.
Under huge stress from a multiqueue/RPS enabled NIC, a single flow udp
receiver can now process ~200.000 pps (instead of ~100 pps before the
patch) on a 8 core machine.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
