This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code. It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume. These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.
It also takes David's advice about removing the layer of bus glue, where
those methods are called. And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the isp116x driver stop using usb_suspend_device() and
usb_resume_device() ... usbcore now calls to the root hub methods,
removing the need for this. It also switches from keventd to khubd
for remote wakeup. (Compile tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/isp116x-hcd.c | 29 ++++-------------------------
drivers/usb/host/isp116x.h | 1 -
2 files changed, 4 insertions(+), 26 deletions(-)
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 34 +++++++++++++++++++++-------------
drivers/usb/core/usb.c | 23 +++++++++++++++++++++--
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/isp116x-hcd.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
include/linux/usb.h | 2 +-
6 files changed, 46 insertions(+), 19 deletions(-)
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increased use of scatter-gather by usb-storage driver after 2.6.13 has
exposed a buggy codepath in isp116x-hcd, which was probably never
visited before: bug happened only for those urbs, for which
URB_SHORT_NOT_OK was set AND short transfer occurred.
The fix attached was tested in 2 ways: (a) it fixed failing
initialization of a flash drive with an embedded hub; (b) the fix was
tested with 'usbtest' against a modified g_zero driver (on top of
net2280), which generated short bulk IN transfers of various lengths
including multiples and non-multiples of max_packet_length.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch isp116x-hcd over from root hub polling to interrupt. This change closes
also a race that was present with the old polling scheme: status polling could
happen in a time window, where root hub status bits were not stable.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.
I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets the isp116x to report overcurrent always per-port.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The isp116x chip will now always be in per-port power switching mode. Remove
conf options to set any other mode.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the power-on-to-power-good-time configuration option for
isp116x-hcd.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When recently addressing remarks by Alexey Dobriyan about
the isp116x-hcd, I introduced a bug in the driver. Please
apply the attached patch to fix it.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Greg,
This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.
Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sorry that it took so long. Here comes a cleanup patch that
addresses the remarks by Alexey Dobriyan about
gregkh-usb-usb-isp116x-hcd-add.patch EXCEPT the remark about
the typecasting of mem_flags argument for kcalloc; this will
be addressed in a later patch.
OlavCleanup of isp116x-hcd.
Signed off by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the host controller drivers; they no longer need to
register their root hubs because usbcore will take care of it for them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an oops triggered at rmmod of isp116x-hcd
after the probe() has failed.
Also, it extends the error message printed, if the driver
cannot detect "Chip's Clock Ready" after a software reset.
As Ian Campbell recently reported, this happens if the
chip's H_WAKEUP pin is not pulled low during software reset.
Several people have already had this issue, hence the update
to the error message.
Also, extend the error message about the failed clock
detection after the software reset.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.
The driver:
- is relatively small, meant for use on embedded platforms.
- runs usbtests 1-14 without problems for days.
- has been in use by 6-7 different people on ARM and PPC platforms,
running a range of devices including USB hubs.
- supports suspend/resume of both the platform device and the root hub;
supports remote wakeup of the root hub (but NOT the platform device)
by USB devices.
- does NOT support ISO transfers (nobody has asked for them).
- is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
