To Reproduce the Problem:
To reproduce this panic consistently, we run an intensive network
application like 'netperf' and then switch to a different console.
After waiting for a couple of seconds, you will see a tx reset has occured.
Reason:
We enable interrupts even if we were not running.
Solution:
Now we will enable interrupts only after we are ready to give up the poll
routine.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_map_single() could fail. We need to properly check the return
code from pci_map_single(). If we can not properly map this address,
then we should cleanup and return the proper return code.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The scatter/gather lists were not being build correctly. When
large frames spanned several buffers the chip would panic.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This change removes use of constants for rx buffer queue size
and instead calculates the queue length based on what he MTU
is set to.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This network device driver shares the same hardware as the qla4xxx
iSCSI driver. Changing the MTU via the device interface will
cause qla4xxx to crash as there is no way to make notification.
Users wishing to change the MTU must do so using an iSCSI
utility such as Qlogic SanSurfer. This forces the user to
unload/reload this network device driver after the MTU
value has been changed in flash.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing
through the Link State Machine
2) Fix deadlock issue when ethtool would call ql_get_settings()
3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We do not need to zero out the 64 byte MAC request I/O control block.
By zeroing out the control block and setting it to proper fields is
redundant work. This is because in the qla3xxx_send() function we will
already set the proper fields in this structure. The unused fields are
not looked at by the hardware and do not need to be zeroed out.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The return code was not properly set when when allocating memory or mapping
memory failed. Depending on the stack, the return code would sometimes
return 0, which indicates everything was ok, when in fact there was an error.
This would cause trouble when the module was removed. Now, we will pass
back the proper return code when an error occurs during the PCI probe.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver contains this little piece of candy:
#if defined(CONFIG_DMA_NONCOHERENT) || defined(CONFIG_NOT_COHERENT_CACHE)
#define ETH_DMA_ALIGN L1_CACHE_BYTES
#else
#define ETH_DMA_ALIGN 8
#endif
Any reason why we're not using dma_get_cache_alignment() instead?
Ralf
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ucc_geth_probe() to use function of_get_mac_address() to obtain the MAC
address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like the skge driver inherited another bug from the sk98lin code.
If I send from 1000mbit port to a machine on 100mbit port, the switch should
be doing hardware flow control, but no pause frames show up in the statistics.
This is the analog of the recent sky2 fixes. The device needs to listen
for multicast pause frames and then not discard them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Work around a bug which occurs when adopting firmware versions
1.4.4 though 1.4.11 where broadcasts are filtered as if they
were multicasts.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple threads performing a transmit can race into
the spidernet tx ring cleanup code. This puts the
relevant check under a lock.
Signed-off-by: Linas Vepstas <lins@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It appears that under certain circumstances, a race will result
in a double-free of an skb. This patch null's out the skb pointer
upon the skb free, avoiding the inadvertent deref of bogus data.
The next patch fixes the actual race.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch separates the hardware descriptor state from the
driver descriptor state, per (old) suggestion from Ben Herrenschmidt.
This compiles and boots and seems to work.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This moves the medium variable into the spidernet card structure.
It renames the GMII_ variables to BCM54XX specific ones.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patches removes logging for SPIDER_NET_GTMFLLINT interrupts.
Since the interrupts are not irregular, and they happen frequently
when using 100Mbps network switches.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves calling init_firmware() from spider_net_probe() to
spider_net_open() so as to use the driver by built-in.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add auto negotiation support for Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As of 2.6.20-git4, the spider_net driver does not compile.
This appears to be due to some archaic usage involving kobjects.
It also fixes a nasty double-free during ifdown of the interface.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This version moves the medium variable to the card specific structure and
changes the GMII_* to BCM54XX_* #defines.
This patch adds improved version of enable_fiber for both the 5421 and
the 5461 phy. It is now possible to specify with these wether you want
autonegotiation or not. This is needed for bladecenter switches where
some expect autonegotiation and some dont seem to like this at all.
Depending on this flag it sets phy->autoneg accordingly for the fiber mode.
More importantly it implements proper read_link and poll_link functions
for both phys which can handle both copper and fiber mode by determining
the medium first and then branching to the required functions. For fiber
they all work fine, for copper they are not tested but return the result
of the genmii_* function anyway which is supposed to work.
The patch moves the genmii_* functions around to avoid foreward declarations.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes checksum offload feature in mcp65 chipsets as they
are not supported in hw.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There seems to be an issue when both MSI-X is enabled and NAPI is
configured. This patch disables MSI-X until the issue is root caused.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The napi poll routine was missing the call to the optimized rx process
routine. This patch adds the missing call for the optimized path.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* clear_page() use is wrong. We might have multiple pages.
Use memset() instead.
* Call pci_unregister_driver() in module exit.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit aeeddc1435, which was
half-baked and broken. It just resulted in compile errors, since
cpufreq_register_driver() still changes the 'driver_data' by setting
bits in the flags field. So claiming it is 'const' _really_ doesn't
work.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Correct debugging output when path record lookup fails
RDMA/cxgb3: Stop the EP Timer on BAD CLOSE
RDMA/cxgb3: cleanups
RDMA/cma: Remove unused node_guid from cma_device structure
IB/cm: Remove ca_guid from cm_device structure
RDMA/cma: Request reversible paths only
IB/core: Set hop limit in ib_init_ah_from_wc correctly
IB/uverbs: Return correct error for invalid PD in register MR
IPoIB: Remove unused local_rate tracking
IPoIB/cm: Improve small message bandwidth
IB/mthca: Make 2 functions static
The change to the devres layer re-orders the execution of cleanup
functions and in turn causes the pcmcia layer to oops as it zaps a
pointer now needed later on. We simply leave the pointer alone.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paulus preferred this over #defining NO_IRQ in the file, since that's
0 for powerpc anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If path_rec_completion() is passed a non-NULL path record pointer
along with an unsuccessful status value, the tracing code incorrectly
prints the (invalid) DLID from the path record rather than the more
interesting status code. The actual logic of the function correctly
uses the path record only if the status indicates a successful lookup.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Toralf Förster pointed out that drivers/video/s3fb.c would fail to compile:
> ...
> CC drivers/video/s3fb.o
> drivers/video/s3fb.c: In function `s3_pci_remove':
> drivers/video/s3fb.c:1003: warning: unused variable `par'
> drivers/video/s3fb.c: In function `s3fb_setup':
> drivers/video/s3fb.c:1141: error: `mtrr' undeclared (first use in this function)
> drivers/video/s3fb.c:1141: error: (Each undeclared identifier is reported only once
> drivers/video/s3fb.c:1141: error: for each function it appears in.)
> make[2]: *** [drivers/video/s3fb.o] Error 1
> make[1]: *** [drivers/video] Error 2
> make: *** [drivers] Error 2
Here is fix, it also fixes broken boot options.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
1. Add race condition check after netif_stop_queue(). tg3_tx() runs
without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
tg3_tso_bug().
2. Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
i.e. they cannot handle TSO headers bigger than 80 bytes. Rename
TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
these chips as well.
3. Update version to 3.74.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Bluetooth drivers need one or more binary firmware images. Export
these image names via the MODULE_FIRMWARE tag.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
Revert "Driver core: let request_module() send a /sys/modules/kmod/-uevent"
Driver core: fix error by cleanup up symlinks properly
make kernel/kmod.c:kmod_mk static
power management: fix struct layout and docs
power management: no valid states w/o pm_ops
Driver core: more fallout from class_device changes for pcmcia
sysfs: move struct sysfs_dirent to private header
driver core: refcounting fix
Driver core: remove class_device_rename
