Closing a pipe endpoint is not normally allowed by the Phonet pipe,
other than as a side after-effect of removing the pipe between two
endpoints. But there is no way to prevent Linux userspace processes
from being killed or suffering from bugs, so this can still happen.
We might as well forcefully close Phonet pipe endpoints then.
The cellular modem supports only a few existing pipes at a time. So we
really should not leak them. This change instructs the modem to destroy
the pipe if either of the pipe's endpoint (Linux socket) is closed too
early.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Do not create expectation when forwarding the PORT
command to avoid blocking the connection. The problem is that
nf_conntrack_ftp.c:help() tries to create the same expectation later in
POST_ROUTING and drops the packet with "dropping packet" message after
failure in nf_ct_expect_related.
- Change ip_vs_update_conntrack to alter the conntrack
for related connections from real server. If we do not alter the reply in
this direction the next packet from client sent to vport 20 comes as NEW
connection. We alter it but may be some collision happens for both
conntracks and the second conntrack gets destroyed immediately. The
connection stucks too.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave reported an rcu lockdep warning on 2.6.35.4 kernel
task->cgroups and task->cgroups->subsys[i] are protected by RCU.
So we avoid accessing invalid pointers here. This might happen,
for example, when you are deref-ing those pointers while someone
move @task from one cgroup to another.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the use of larger initial windows, as originally specified in
RFC 3390, to use the newer IW values specified in RFC 5681, section 3.1.
The changes made in RFC 5681 are:
a) the setting now is more clearly specified in units of segments (as the
comments by John Heffner emphasized, this was not very clear in RFC 3390);
b) for connections with 1095 < SMSS <= 2190 there is now a change:
- RFC 3390 says that IW <= 4380,
- RFC 5681 says that IW = 3 * SMSS <= 6570.
Since RFC 3390 is older and "only" proposed standard, whereas the newer RFC 5681
is already draft standard, it seems preferable to use the newer IW variant.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates initial-window code common to TCP and CCID-2:
* TCP uses RFC 3390 in a packet-oriented manner (tcp_input.c) and
* CCID-2 uses RFC 3390 in packet-oriented manner (RFC 4341).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a "user timeout" support as described in RFC793. The
socket option is also needed for the the local half of RFC5482 "TCP User
Timeout Option".
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int,
when > 0, to specify the maximum amount of time in ms that transmitted
data may remain unacknowledged before TCP will forcefully close the
corresponding connection and return ETIMEDOUT to the application. If
0 is given, TCP will continue to use the system default.
Increasing the user timeouts allows a TCP connection to survive extended
periods without end-to-end connectivity. Decreasing the user timeouts
allows applications to "fail fast" if so desired. Otherwise it may take
upto 20 minutes with the current system defaults in a normal WAN
environment.
The socket option can be made during any state of a TCP connection, but
is only effective during the synchronized states of a connection
(ESTABLISHED, FIN-WAIT-1, FIN-WAIT-2, CLOSE-WAIT, CLOSING, or LAST-ACK).
Moreover, when used with the TCP keepalive (SO_KEEPALIVE) option,
TCP_USER_TIMEOUT will overtake keepalive to determine when to close a
connection due to keepalive failure.
The option does not change in anyway when TCP retransmits a packet, nor
when a keepalive probe will be sent.
This option, like many others, will be inherited by an acceptor from its
listener.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_scan_completed() function was a frequent
source of potential deadlocks, since it is called by
drivers but may call back into drivers, so drivers had
to make sure to call it without any locks held, which
frequently lead to more complex code in drivers. Avoid
that problem by allowing the function to be called in
any context, and queueing the actual work it does.
Also update the documentation for it to indicate this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change SCTP_DEBUG_PRINTK and SCTP_DEBUG_PRINTK_IPADDR to
use do { print } while (0) guards.
Add SCTP_DEBUG_PRINTK_CONT to fix errors in log when
lines were continued.
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Add a missing newline in "Failed bind hash alloc"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spelling and readability of a few lines of kernel doc:
s/issueing/issuing/g
s/approriate/appropriate/g
s/supported by simply/supported simply by/
s/IEEE80211_HW_BEACON_FILTERING/IEEE80211_HW_BEACON_FILTER/g
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.
Fix this by doing the full expensive sum check if the optimized check
triggers.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Add some documentation for cfg80211. I'm hoping some of
the regulatory documentation will be filled by somebody
more familiar with it, hint hint! :)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a small problem in the documentation for
ieee80211_request_smps, and a now erroneous
inclusion of enum ieee80211_key_alg, which no
longer exists after the change to ciphers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function analyses only its single, value-passed
argument, and has no side effects. Thus it can be
const, which makes mac80211 smaller, for example:
text data bss dec hex filename
362518 16720 884 380122 5ccda mac80211.ko (before)
362358 16720 884 379962 5cc3a mac80211.ko (after)
a 160 byte saving in text size, and an optimisation
because the function won't be called as often.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the irlan_cb struct.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP: introduce "pptp" module which implements point-to-point tunneling protocol using pppox framework
NET: introduce the "gre" module for demultiplexing GRE packets on version criteria
(required to pptp and ip_gre may coexists)
NET: ip_gre: update to use the "gre" module
This patch introduces then pptp support to the linux kernel which
dramatically speeds up pptp vpn connections and decreases cpu usage in
comparison of existing user-space implementation
(poptop/pptpclient). There is accel-pptp project
(https://sourceforge.net/projects/accel-pptp/) to utilize this module,
it contains plugin for pppd to use pptp in client-mode and modified
pptpd (poptop) to build high-performance pptp NAS.
There was many changes from initial submitted patch, most important are:
1. using rcu instead of read-write locks
2. using static bitmap instead of dynamically allocated
3. using vmalloc for memory allocation instead of BITS_PER_LONG + __get_free_pages
4. fixed many coding style issues
Thanks to Eric Dumazet.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: add ACT_CSUM action to update packets checksums
ACT_CSUM can be called just after ACT_PEDIT in order to re-compute some
altered checksums in IPv4 and IPv6 packets. The following checksums are
supported by this patch:
- IPv4: IPv4 header, ICMP, IGMP, TCP, UDP & UDPLite
- IPv6: ICMPv6, TCP, UDP & UDPLite
It's possible to request in the same action to update different kind of
checksums, if the packets flow mix TCP, UDP and UDPLite, ...
An example of usage is done in the associated iproute2 patch.
Version 3 changes:
- remove useless goto instructions
- improve IPv6 hop options decoding
Version 2 changes:
- coding style correction
- remove useless arguments of some functions
- use stack in tcf_csum_dump()
- add tcf_csum_skb_nextlayer() to factor code
Signed-off-by: Gregoire Baron <baronchon@n7mm.org>
Acked-by: jamal <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.
The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().
http://marc.info/?l=linux-netdev&m=128084897415886&w=2
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU. That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.
ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead. With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput. Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.
This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add missing kernel-doc notation to struct sock:
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid'
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred'
Warning(include/net/sock.h:324): No description found for parameter 'sk_classid'
Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
TXATTRCREATE: Prepare a fid for setting xattr value on a file system object.
size[4] TXATTRCREATE tag[2] fid[4] name[s] attr_size[8] flags[4]
size[4] RXATTRCREATE tag[2]
txattrcreate gets a fid pointing to xattr. This fid can later be
used to set the xattr value.
flag value is derived from set Linux setxattr. The manpage says
"The flags parameter can be used to refine the semantics of the operation.
XATTR_CREATE specifies a pure create, which fails if the named attribute
exists already. XATTR_REPLACE specifies a pure replace operation, which
fails if the named attribute does not already exist. By default (no flags),
the extended attribute will be created if need be, or will simply replace
the value if the attribute exists."
The actual setxattr operation happens when the fid is clunked. At that point
the written byte count and the attr_size specified in TXATTRCREATE should be
same otherwise an error will be returned.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
TXATTRWALK: Descend a ATTR namespace
size[4] TXATTRWALK tag[2] fid[4] newfid[4] name[s]
size[4] RXATTRWALK tag[2] size[8]
txattrwalk gets a fid pointing to xattr. This fid can later be
used to read the xattr value. If name is NULL the fid returned
can be used to get the list of extended attribute associated to
the file system object.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Implement 9p2000.L version of open(LOPEN) interface in 9p client.
For LOPEN, no need to convert the flags to and from 9p mode to VFS mode.
Synopsis:
size[4] Tlopen tag[2] fid[4] mode[4]
size[4] Rlopen tag[2] qid[13] iounit[4]
[Fix mode bit format - jvrao@linux.vnet.ibm.com]
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbegren <ericvh@gmail.com>
SYNOPSIS
size[4] Tlcreate tag[2] fid[4] name[s] flags[4] mode[4] gid[4]
size[4] Rlcreate tag[2] qid[13] iounit[4]
DESCRIPTION
The Tlreate request asks the file server to create a new regular file with the
name supplied, in the directory (dir) represented by fid.
The mode argument specifies the permissions to use. New file is created with
the uid if the fid and with supplied gid.
The flags argument represent Linux access mode flags with which the caller
is requesting to open the file with. Protocol allows all the Linux access
modes but it is upto the server to allow/disallow any of these acess modes.
If the server doesn't support any of the access mode, it is expected to
return error.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Implement TMKDIR as part of 2000.L Work
Synopsis
size[4] Tmkdir tag[2] fid[4] name[s] mode[4] gid[4]
size[4] Rmkdir tag[2] qid[13]
Description
mkdir asks the file server to create a directory with given name,
mode and gid. The qid for the new directory is returned with
the mkdir reply message.
Note: 72 is selected as the opcode for TMKDIR from the reserved list.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] Tmknod tag[2] fid[4] name[s] mode[4] major[4] minor[4] gid[4]
size[4] Rmknod tag[2] qid[13]
Description
mknod asks the file server to create a device node with given major and
minor number, mode and gid. The qid for the new device node is returned
with the mknod reply message.
[sripathik@in.ibm.com: Fix error handling code]
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Create a symbolic link
SYNOPSIS
size[4] Tsymlink tag[2] fid[4] name[s] symtgt[s] gid[4]
size[4] Rsymlink tag[2] qid[13]
DESCRIPTION
Create a symbolic link named 'name' pointing to 'symtgt'.
gid represents the effective group id of the caller.
The permissions of a symbolic link are irrelevant hence it is omitted
from the protocol.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Reviewed-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch adds a helper function to get the dentry from inode and
uses it in creating a Hardlink
SYNOPSIS
size[4] Tlink tag[2] dfid[4] oldfid[4] newpath[s]
size[4] Rlink tag[2]
DESCRIPTION
Create a link 'newpath' in directory pointed by dfid linking to oldfid path.
[sripathik@in.ibm.com : p9_client_link should not free req structure
if p9_client_rpc has returned an error.]
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
SYNOPSIS
size[4] Tsetattr tag[2] attr[n]
size[4] Rsetattr tag[2]
DESCRIPTION
The setattr command changes some of the file status information.
attr resembles the iattr structure used in Linux kernel. It
specifies which status parameter is to be changed and to what
value. It is laid out as follows:
valid[4]
specifies which status information is to be changed. Possible
values are:
ATTR_MODE (1 << 0)
ATTR_UID (1 << 1)
ATTR_GID (1 << 2)
ATTR_SIZE (1 << 3)
ATTR_ATIME (1 << 4)
ATTR_MTIME (1 << 5)
ATTR_ATIME_SET (1 << 7)
ATTR_MTIME_SET (1 << 8)
The last two bits represent whether the time information
is being sent by the client's user space. In the absense
of these bits the server always uses server's time.
mode[4]
File permission bits
uid[4]
Owner id of file
gid[4]
Group id of the file
size[8]
File size
atime_sec[8]
Time of last file access, seconds
atime_nsec[8]
Time of last file access, nanoseconds
mtime_sec[8]
Time of last file modification, seconds
mtime_nsec[8]
Time of last file modification, nanoseconds
Explanation of the patches:
--------------------------
*) The kernel just copies relevent contents of iattr structure to
p9_iattr_dotl structure and passes it down to the client. The
only check it has is calling inode_change_ok()
*) The p9_iattr_dotl structure does not have ctime and ia_file
parameters because I don't think these are needed in our case.
The client user space can request updating just ctime by calling
chown(fd, -1, -1). This is handled on server side without a need
for putting ctime on the wire.
*) The server currently supports changing mode, time, ownership and
size of the file.
*) 9P RFC says "Either all the changes in wstat request happen, or
none of them does: if the request succeeds, all changes were made;
if it fails, none were."
I have not done anything to implement this specifically because I
don't see a reason.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
SYNOPSIS
size[4] Tgetattr tag[2] fid[4] request_mask[8]
size[4] Rgetattr tag[2] lstat[n]
DESCRIPTION
The getattr transaction inquires about the file identified by fid.
request_mask is a bit mask that specifies which fields of the
stat structure is the client interested in.
The reply will contain a machine-independent directory entry,
laid out as follows:
st_result_mask[8]
Bit mask that indicates which fields in the stat structure
have been populated by the server
qid.type[1]
the type of the file (directory, etc.), represented as a bit
vector corresponding to the high 8 bits of the file's mode
word.
qid.vers[4]
version number for given path
qid.path[8]
the file server's unique identification for the file
st_mode[4]
Permission and flags
st_uid[4]
User id of owner
st_gid[4]
Group ID of owner
st_nlink[8]
Number of hard links
st_rdev[8]
Device ID (if special file)
st_size[8]
Size, in bytes
st_blksize[8]
Block size for file system IO
st_blocks[8]
Number of file system blocks allocated
st_atime_sec[8]
Time of last access, seconds
st_atime_nsec[8]
Time of last access, nanoseconds
st_mtime_sec[8]
Time of last modification, seconds
st_mtime_nsec[8]
Time of last modification, nanoseconds
st_ctime_sec[8]
Time of last status change, seconds
st_ctime_nsec[8]
Time of last status change, nanoseconds
st_btime_sec[8]
Time of creation (birth) of file, seconds
st_btime_nsec[8]
Time of creation (birth) of file, nanoseconds
st_gen[8]
Inode generation
st_data_version[8]
Data version number
request_mask and result_mask bit masks contain the following bits
#define P9_STATS_MODE 0x00000001ULL
#define P9_STATS_NLINK 0x00000002ULL
#define P9_STATS_UID 0x00000004ULL
#define P9_STATS_GID 0x00000008ULL
#define P9_STATS_RDEV 0x00000010ULL
#define P9_STATS_ATIME 0x00000020ULL
#define P9_STATS_MTIME 0x00000040ULL
#define P9_STATS_CTIME 0x00000080ULL
#define P9_STATS_INO 0x00000100ULL
#define P9_STATS_SIZE 0x00000200ULL
#define P9_STATS_BLOCKS 0x00000400ULL
#define P9_STATS_BTIME 0x00000800ULL
#define P9_STATS_GEN 0x00001000ULL
#define P9_STATS_DATA_VERSION 0x00002000ULL
#define P9_STATS_BASIC 0x000007ffULL
#define P9_STATS_ALL 0x00003fffULL
This patch implements the client side of getattr implementation for
9P2000.L. It introduces a new structure p9_stat_dotl for getting
Linux stat information along with QID. The data layout is similar to
stat structure in Linux user space with the following major
differences:
inode (st_ino) is not part of data. Instead qid is.
device (st_dev) is not part of data because this doesn't make sense
on the client.
All time variables are 64 bit wide on the wire. The kernel seems to use
32 bit variables for these variables. However, some of the architectures
have used 64 bit variables and glibc exposes 64 bit variables to user
space on some architectures. Hence to be on the safer side we have made
these 64 bit in the protocol. Refer to the comments in
include/asm-generic/stat.h
There are some additional fields: st_btime_sec, st_btime_nsec, st_gen,
st_data_version apart from the bitmask, st_result_mask. The bit mask
is filled by the server to indicate which stat fields have been
populated by the server. Currently there is no clean way for the
server to obtain these additional fields, so it sends back just the
basic fields.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Eric Van Hensbegren <ericvh@gmail.com>
This patch implements the kernel part of readdir() implementation for 9p2000.L
Change from V3: Instead of inode, server now sends qids for each dirent
SYNOPSIS
size[4] Treaddir tag[2] fid[4] offset[8] count[4]
size[4] Rreaddir tag[2] count[4] data[count]
DESCRIPTION
The readdir request asks the server to read the directory specified by 'fid'
at an offset specified by 'offset' and return as many dirent structures as
possible that fit into count bytes. Each dirent structure is laid out as
follows.
qid.type[1]
the type of the file (directory, etc.), represented as a bit
vector corresponding to the high 8 bits of the file's mode
word.
qid.vers[4]
version number for given path
qid.path[8]
the file server's unique identification for the file
offset[8]
offset into the next dirent.
type[1]
type of this directory entry.
name[256]
name of this directory entry.
This patch adds v9fs_dir_readdir_dotl() as the readdir() call for 9p2000.L.
This function sends P9_TREADDIR command to the server. In response the server
sends a buffer filled with dirent structures. This is different from the
existing v9fs_dir_readdir() call which receives stat structures from the server.
This results in significant speedup of readdir() on large directories.
For example, doing 'ls >/dev/null' on a directory with 10000 files on my
laptop takes 1.088 seconds with the existing code, but only takes 0.339 seconds
with the new readdir.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
