Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Gregory Bean <gbean@codeaurora.org>
Tested-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: "Hennerich, Michael" <Michael.Hennerich@analog.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds (well, re-adds actually) handling for events/IRQs through cs5535
GPIOs. In the wild and wooly world of CS5535, setup_event() is for
assigning an IRQ to a GPIO filter/event pair, and set_irq() sets up the
pair to trigger IRQs.
These should really only be used in highly platform-specific drivers (such
as OLPC's DCON driver). Sadly, because set_irq() uses MSRs, this causes
the driver to become X86-specific.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the tc35892 core/gpio drivers to tc3589x to include
new variants in the same mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:
"Atomic write transactions to the atomic GPIO High Bank Feature Bit
registers should only affect the bits selected [...]"
"after Suspend, an atomic write transaction [...] will clear all
non-selected bits of the accessed register."
In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).
The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed for supporting the upcoming VX855 camera and OLPC DCON
drivers, as well as the advanced viafb features on non-OLPC hardware
based on this chip.
Based on earlier work by Harald Welte.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Free allocated memory. Call stmpe_disable() if it was enabled.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In this case the logic is very similar but the IRQs are not exposed and
the device is not picked up via PCI
Based on a separate internal whitney point driver by Yin Kangkai.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deweird this driver.
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some versions of the hardware can trash the IER register if simultaneous
interrupts occur. This patch works around it by using a local copy of the
register and restoring it after every interrupt.
Signed-off-by: Tomas Hallenberg <tomas.hallenberg@pelagicore.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Our Moorestown platform has two max7315 chips which is covered by pca953x
i2c gpio driver.
A while ago this driver got updated with nested irq thread support, and it
broke the compatibity with "request_irq". For example, the gpio_keys.c
driver can not work with this driver now. This patch fixes the issue by
switching to generic_handle_irq.
Also fix the irq_base issue: irq_base == 0 is valid, and a "-1" value
should mean invalid. IRQ 0 is not a valid IRQ, irq_base of 0 is valid.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
DTB is always big-endian that's why is necessary
to convert it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For board-specific initialization.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The debounce times are approximate, they can be selected using the two
input functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the GPIOs on STMPE I/O Expanders.
[l.fu@pengutronix.de: fix set direction input]
[l.fu@pengutronix.de: set GPIO alternate function while requesting]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pca953x driver requires the use of threaded irqs as its irq
demultiplexer can sleep. Our irq handler can be called from any context,
so use request_any_context_irq to allow threaded irqs as well.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Reported-by: Ian Jeffray <ian@jeffray.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As sysfs_notify_dirent has been made irq safe, there is no reason to not
call it directly from irq. With the work_struct removed, the remaining
element in poll_desc is a sysfs_dirent pointer which may not be NULL. We
can therefore store it directly in the idr and pass it as context to the
irq handler.
Most part of the patch deals with renaming defines and variables to
reflect their new use without functional change.
I also took the opportunity to initialize the idr statically.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Be more consistent about runtime programming interface abuse warnings,
which can reduce some confusion and trigger bugfixes. Based on an
observation and patch from Jani Nikula.
Also update doc to highlight some sleeping-call issues and to match some
recent changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide sane defaults for pcf857x, so the driver can be used w/o providing
platform data (and thus can be simply bound via OF tree).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpios on the max730x chips have support for internal pullups while in
input mode.
This patch adds support for configuring these pullups via platform data.
A new member ("input_pullup_active") to the platform data struct is
introduced. A set bit in this variable activates the pullups while the
respective port is in input mode. This is a compatible enhancement since
unset bits lead to disables pullups which was the default in the original
driver.
_Note_: the 4 lowest bits in "input_pullup_active" are unused because the
first 4 ports of the controller are not used, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
