* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
h8300: Move gpio.h to gpio-internal.h
gpio: pl061: add DT binding support
gpio: fix build error in include/asm-generic/gpio.h
gpiolib: Ensure struct gpio is always defined
irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip
gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL
gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL
gpio: langwell: ensure alternate function is cleared
gpio-pch: Support interrupt function
gpio-pch: Save register value in suspend()
gpio-pch: modify gpio_nums and mask
gpio-pch: support ML7223 IOH n-Bus
gpio-pch: add spinlock in suspend/resume processing
gpio-pch: Delete invalid "restore" code in suspend()
gpio-ml-ioh: Fix suspend/resume issue
gpio-ml-ioh: Support interrupt function
gpio-ml-ioh: Delete unnecessary code
gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
gpio/nomadik: use genirq core to track enablement
gpio/nomadik: disable clocks when unused
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, GFP_KERNEL is used as parameter of irq_alloc_descs like below.
irq_base = irq_alloc_descs(-1, IOH_IRQ_BASE, num_ports[j],
GFP_KERNEL);
This is not true.
So, this patch uses NUMA_NO_NODE not GFP_KERNEL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, GFP_KERNEL is used as parameter of irq_alloc_descs like below.
irq_base = irq_alloc_descs(-1, IOH_IRQ_BASE, num_ports[j],
GFP_KERNEL);
This is not true.
So, this patch uses NUMA_NO_NODE not GFP_KERNEL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_base was set to 0 if no system platform data or open firmware
platform data was provided. This led to conflicts, if any other gpiochip
with a gpiobase of 0 was instantiated already. Setting it to -1 will
automatically use the first one available.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With commit f64ad1a0e2, "gpio/omap: cleanup _set_gpio_wakeup(), remove
ifdefs", access to build time conditionally omitted 'suspend_wakeup'
member of the 'gpio_bank' structure has been placed unconditionally in
function _set_gpio_wakeup(), which is always built. This resulted in the
driver compilation broken for certain OMAP1, i.e., non-OMAP16xx,
configurations.
Really required or not in previously excluded cases, define this
structure member unconditionally as a fix.
Tested with a custom OMAP1510 only configuration.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Alternate function must be zero for the pin to act as
a GPIO.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, when suspend is occurred, register im0/1 and gpio_use_sel are not
saved.
This patch modifies so that register im0/1 and gpio_use_sel are saved.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, the number of GPIO pins is set fixed value(=12).
Also PIN MASK is set as '0xfff'.
However the pins differs by IOH.
This patch sets the value correctly.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, some registers are not saved in case changing to suspend state.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This register restore processing is unnecessary in suspend processing.
(The restore processing is already in resume processing)
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the PXA
GPIO driver down to the GPIO subsystem so it can be consolidated.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mx3_gpio_irq_handler() is also called on imx6q which has GIC as
the primary interrupt controller. As GIC implements the fasteoi flow
control, we need to add chained_irq_enter/exit() to
mx3_gpio_irq_handler() for signaling EOI, otherwise system will hang
whenever there is a gpio irq triggered.
v2: use chained_irq_{enter,exit}()
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Building a kernel with hotplug disabled results in a link failure:
`bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
This is because of bgpio_remove() is exported. It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.
Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This rewrites the U300 GPIO so as to use gpiolib and
struct gpio_chip instead of just generic GPIO, hiding
all the platform specifics and passing in GPIO chip
variant as platform data at runtime instead of the
compiletime kludges.
As a result <mach/gpio.h> is now empty for U300 and
using just defaults.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Debian kernel maintainers <debian-kernel@lists.debian.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 5093aec872
"arm: davinci: Cleanup irq chip code", the variable 'mask' and 'g'
are not being used.
This patch eliminate below unused variable warnings:
CC drivers/gpio/gpio-davinci.o
drivers/gpio/gpio-davinci.c: In function 'gpio_irq_type':
drivers/gpio/gpio-davinci.c:234: warning: unused variable 'mask'
drivers/gpio/gpio-davinci.c:233: warning: unused variable 'g'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_to_gpio is being removed. Replace the only use of that API by
the ARM Tegra sub-architecture.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the ep93xx machine specific dependencies for gpio_to_irq() by
hooking up the callback in the driver and using __gpio_to_irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the KS8695 GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-gpio".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
