- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make 2 needlessly global functions static
- remove cpia2_setup(): the driver already allows setting parameters
through module_param(), and there's no reason for having two different
ways for setting the same parameters
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved keymaps to the ir-common module, and export them from there, instead
of #including them in each module
Included missing files from V4L/DVB(3197).
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the strange crashes I was seeing after using
bttv card, caused by a buffer overflow in bttv_risc_packed.
The instruction buffer size calculation contains two errors:
(a) a non-zero padding value can push the start of the next bpl
section to just before a page border, leading to more scanline
splits and thus additional instructions.
(b) the first DMA region can be smaller than one page, so there can
be a scanline split even if bpl*lines is smaller than PAGE_SIZE.
For example, consider the case where offset is 0, bpl is 2, padding
is 4094, lines is smaller than 2048, the first DMA region has size 1
and all others have size PAGE_SIZE, assumed to equal 4096. Then
all bpl regions cross page borders and the number of instructions
written is 2*lines+2, rather than lines+2 (the current estimate).
With this patch the number of instructions for this example is
estimated to be 2*lines+3.
Also, the BUG_ON that was supposed to catch buffer overflows contained
a thinko causing it fire only if the buffer was overrun by a factor of
16 or more, so it fixes the the BUG_ON's (using sizeof rather than "4").
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fix temporary debug code by changing printk to dprintk at level 1.
- move CORE_IOCTL messages from level 1 to level 2.
- this should help with selective debugging,
while not filling people's logs up during normal use.
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Current xc3028 support is still experimental, requiring more work to be
sent to mainstream. It will be kept only at mercurial tree on
http://linuxtv.org/hg until fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After a FIFO corruptions occurrs (generally due to buffer overflow), FIFO
contents needs to be discarted.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, root may change parameters while module is running.
Thanks to Edgar Toerning
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed broken IF-OUT on pinnacle sat board.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ignore invalid messages on cx24110 frontend.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field "dvr" in struct dmxdev is competely unused. Remove
it and code which allocates, initializes and frees it.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There has been a CPIA2 driver out of kernel for a long time and it has
been pretty clean for some time too. This is an import of the
sourceforge driver which has been stripped of
- 2.4 back compatibility
- 2.4 old style MJPEG ioctls
A couple of functions have been made static and the docs have been
repackaged into Documentation/video4linux. The rvmalloc/free functions now
match the cpia driver again. Other than that this is the code as is.
Tested on x86-64 with a QX5 microscope.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, only NTSC and PAL/M were associated to 30fps and
525 lines, so, PAL/60 were not handled properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a new function that allows printing ioctl arguments.
This makes easier to include debug code under v4l ioctl
handling.
Also fixed some declarations on internal ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote controller on the LifeView FlyDVB-T Duo card work flawlessly
with the same settings as the LifeView FlyDVB-T LR301 card.
Signed-off-by: Rudo Thomas <rudo@matfyz.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Standard video using the cx88 broadcast decoder is
working, but blackbird isn't working yet, audio is only
working correctly for television mode. S-Video and Composite
are working for video-only, so I have them disabled for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enable the tuv1236 tuner on the Kworld-ATSC110 card so that the
tuner can be identified when tuners.ko loads.
- With this change it is no longer necessary to remove and reload
the tuner module in order to get the tuv1236 identified.
- This code was copied from the ATI HDTV Wonder init routine (in cx88-cards.c)
which also uses the TUV1236D.
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- There is no radio with this tuner card...
Thanks-to: Dwaine Garden <DwaineGarden@rogers.com>
- fixed capitalization in card name.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When tuning VSB, use ANT input
- When tuning QAM, use CABLE input
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote control interface for this board is the same as the one for
BTTV_BOARD_CONCEPTRONIC_CTVFMI2
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for ELSA EX-VISION 700TV, which is the ELSA Japan's
flagship model of the software encoding TV capture card.
All inputs (Television, Composite1 and S-Video) have been tested.
Signed-off-by: Tamuki Shoichi <tamuki@linet.gr.jp>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add radio support for KWorld HardwareMpegTV XPert
- fix GPIO settings for tv and radio
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- remove tuner.ko build dependency on xc3028.o , which will be added again later.
- fix the following build error when using the "make kernel-links" build method to
symlink the latest code from the v4l-dvb repository into the kernel source:
drivers/media/video/xc3028.c:31:20: em28xx.h: No such file or directory
drivers/media/video/xc3028.c: In function `xc3028_init':
drivers/media/video/xc3028.c:120: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:121: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:139: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:140: error: dereferencing pointer to incomplete type
make[3]: *** [drivers/media/video/xc3028.o] Error 1
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Current xc3028 support is still experimental, requiring more work to be
sent to mainstream. So, it was marked inside some defines, in order to be
removed by gentree.pl stript. Script also updated to remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed xc3028 firmware extractor for terratec's emBDA.sys firmware
Fixed delay in firmwareupload, now terratec's firmware also works
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for xc3028 to v4l which adds support for:
* Terratec Hybrid XS (analogue)
* Hauppauge HVR 900 (analogue)
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* compat_alloc_user_space() returns __user pointer
* copying between two userland areas is copy_in_user(), not copy_from_user()
* dereferencing userland pointers is bad
* so's get_user() from local variables
... plus usual __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Adding support for Terratec Prodigy XS
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
disabled debug on by default in tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forgot to take the NTSC frequency offset into account.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.
The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When a firmware was downloaded dvb_usb_device_init returns NULL for the
dvb_usb_device, then nothing should be done with that pointer and device,
because it will re-enumerate.
- A new firmware should be used with digitv devices.
- It should make "slave"-devices work and others, too.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reassigning function pointers in a static led to infinite loops when using
multiple VP7045-based device at the same time on one system. Using kmalloc'd
copies for reassignments is better.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 demodulator in
TH7579 and LGZ201 -based FusionHDTV Bluebird usb boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 in USB demodulator of the
Dual Digital board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.
The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add initial support for KWorld HardwareMpegTV XPert.
- uses silicon tuner: tda8290 + tda8275
- standard video using cx88 broadcast decoder is working.
- blackbird mpeg encoder support (cx23416) not yet working.
- FM radio untested.
- audio is only working correctly in television mode,
all other modes disabled.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is an analog / digital hybrid card.
Signed-off-by: Peter Hartshorn <p3r@users.sourceforge.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed em28xx based system lockup, device needs to be initialized
before starting the isoc transfer otherwise the system will completly lock up.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When a firmware was downloaded dvb_usb_device_init returns NULL for the
dvb_usb_device, then nothing should be done with that pointer and device,
because it will re-enumerate.
- A new firmware should be used with digitv devices.
- It should make "slave"-devices work and others, too.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reassigning function pointers in a static led to infinite loops when using
multiple VP7045-based device at the same time on one system. Using kmalloc'd
copies for reassignments is better.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 demodulator in
TH7579 and LGZ201 -based FusionHDTV Bluebird usb boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 in USB demodulator of the
Dual Digital board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Analog and DVB-T are working, Remote not yet.
This card is based on the new LifeView design, there should be many variants.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Set outputs to tristate in sleep mode
- Reduce dangerously high firmware download speed with 16MHz xtal
- added tda827x configuration with GPIOs low
- added comments to stupid looking IIC reads that work around bugs in
the tda10046.
- some minor updates
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch
- works around a bug in the I2C bridge that makes the initialization
of the TDA10046 fail on recent LifeView cards
- puts the AGC output to tristate in sleep mode. This is necessary for
recent hybrid cards that switch the AGC via tristateing.
Signed-off-by: Hartmut Hackmann<hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Additionally to the card support, this changeset adds the option
tda10046lifeview to get_dvb_firmware to download tda10046 firmware
from LifeView's site.
Signed-off-by: Giampiero Giancipoli <gianci@libero.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
South Korea uses NTSC-M but with A2 audio instead of BTSC. Several audio
chips need this information in order to set the correct audio processing
registers.
Acked-by: Mauro Carvalho Chehab <mauro_chehab@yahoo.com.br>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
South Korea uses NTSC-M but with A2 audio instead of BTSC. Several audio
chips need this information in order to set the correct audio processing
registers.
Acked-by: Mauro Carvalho Chehab <mauro_chehab@yahoo.com.br>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add IR support to KWorld DVB-T (cx22702-based)
Signed-off-by: Marco Manenti <marco_manenti@colman.it>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename DVB_USB_CXUSB one-liner description to:
Conexant USB2.0 hybrid reference design support.
- with the addition of bluebird support to dvb-usb-cxusb,
it now depends on lgdt330x and mt352 modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add IR support to KWorld DVB-T (cx22702-based)
Signed-off-by: Marco Manenti <marco_manenti@colman.it>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently, having the number of lines fixed at 4 reduces (or even kills)
the buzz found in NICAM stereo with analog sound.
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename DVB_USB_CXUSB one-liner description to:
Conexant USB2.0 hybrid reference design support.
- with the addition of bluebird support to dvb-usb-cxusb,
it now depends on lgdt330x and mt352 modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With tuner_debug enabled, if a tuner tries to use a video standard that doesn't
have a matching tuner_params defined, the IFPCoff value and tuner number will
be displayed, and the default tuner_params entry will be used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a given tuner definition contains more than one tuner_params array members,
it will try to select the appropriate tuner_params based on the video standard
in use. If there is no tuner_params defined for the current video standard, it
will select the default, tuner_params[0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch allows to select AM sound even if NICAM is detected.
Proposed by Alain Frappin
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now, all tuners are using the first tuner_params[]
array element for analog mode. We are now ready to begin merging
similar tuner definitions together, such that each tuner definition
will have a tuner_params struct for each available video standard.
The tuner_params[] array element will be chosen based on the video
standard in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- tuner_dbg will show tuner param and range selected
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- allow multiple tuner params in each tuner definition.
- the correct tuner_params element will be chosen based on
current video standard.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- move video std detection to top of set_tv_freq function
- we must detect video std first, so that we can choose the correct
tuner_params
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently, having the number of lines fixed at 4 reduces (or even kills)
the buzz found in NICAM stereo with analog sound.
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_params element is an array of undefined length,
with each array member being a set of parameters for each
video standard type.
The number of members in the tuner_params array
will be stored in tuners[]->count
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Move config byte from tuner_params to tuner_range struct.
- dvb tuners must be able to set different config byte for each range.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename cb variable names in tuner structures for global consistency
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- default_tuner_init was called twice due to a missing break statement.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make needlessly global code static
- #if 0 the following unused global functions:
- b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq()
- b2c2/flexcop-dma.c: flexcop_dma_config_packet_count()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fixed VBI compilation.
- Included capacity to specify vbi and video number.
- Added a better control for using more than one em28xx device.
- VIDIOC_G_FMT now calls a function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved some hardcoded minor numbers to videodev2.h
- Included more comments for sliced VBI standards
- Included some VBI macros to group similar standards
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tda9887 has an I2C id reserved for it, but it hasn't been using
it. Probably an oversight. Fixed with this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make VP-3054 Secondary I2C Bus Support a Kconfig option.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Mark Typhoon cards as OEM of Lifeview.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added other sliced VBI types to videodev2.h
- tvp5150 now uses standard V4L2 API codes from videodev2.h
- Implemented VIDIOC_G_SLICED_VBI_CAP for tvp5150. This is
dynamically filled based on defined VDP C-RAM values filled
by the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Renamed some registers and improved register debug message
- Some cleanups at register dump
- Added code to set VBI processor (VDP)
- VBI code still incomplete
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added credits for sn9c102 kernel module and his author as
some parts of em28xx-video were based.
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Acked-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Ludovico Cavedon <cavedon@sssup.it>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- default_tuner_init was called twice due to a missing break statement.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make needlessly global code static
- #if 0 the following unused global functions:
- b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq()
- b2c2/flexcop-dma.c: flexcop_dma_config_packet_count()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tda9887 has an I2C id reserved for it, but it hasn't been using
it. Probably an oversight. Fixed with this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make VP-3054 Secondary I2C Bus Support a Kconfig option.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Mark Typhoon cards as OEM of Lifeview.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tvp5150 type were determined by a secondary register instead of
using ROM code.
- tvp5150am1 have ROM=4.0, while tvp5150a have ROM=3.33 (decimal).
All other ROM versions are reported as unknown tvp5150.
- Except for reporting, current code doesn't enable any special feature
for tvp5150am1 or tvp5150a. Code should work for both models (but were
tested only for tvp5150am1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add probe check for the tda9840 to prevent misdetection of a Micronas
dpl3518a as a tda9840.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added credits for sn9c102 kernel module and his author as
some parts of em28xx-video were based.
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Acked-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Ludovico Cavedon <cavedon@sssup.it>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tvp5150 type were determined by a secondary register instead of
using ROM code.
- tvp5150am1 have ROM=4.0, while tvp5150a have ROM=3.33 (decimal).
All other ROM versions are reported as unknown tvp5150.
- Except for reporting, current code doesn't enable any special feature
for tvp5150am1 or tvp5150a. Code should work for both models (but were
tested only for tvp5150am1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add probe check for the tda9840 to prevent misdetection of a Micronas
dpl3518a as a tda9840.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix handling of VIDIOC_G_TUNER audmode in msp3400: audmode
is only changed by the user with S_TUNER, never by the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove duplicated keymaps and add keymap for KWorld LTV883IR.
Thanks to Jon Ferguson <jon@sd-6.org>.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- All the keymaps have the same structure, and can be shared between different
chips, so it makes no sense having them scattered between the input files.
This aggregates them all at ir-common module.
- Added new Hauppauge remote (Hauppauge grey), contributed by J.O. Aho
<trizt@iname.com> (with some small changes)
Changed KEY_KPx (keypad numerals) references to KEY_x, to avoid problems
when NumLock is off (suggested by Peter Missel <peter.missel@onlinehome.de>)
- Some cleanups at IR code
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- For the Hauppauge PVR cards there are at least two different remotes, one
completly black and one that is Grey and black, they keys differ in values
eg Black remotes 'mute' has the same value as Grey remotes 'menu'.
- This enables the user to select which keymapping to use by using the
hauppauge parm. Unlike to the black remote keys, all keys are
mapped for the grey remote and the ATi usb remote mappings has been
followed.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added remote control support for pinnacle pctv
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved MSP_SET_MATRIX to v4l2-common.h
- Fix typos and integer overflows in tea5767.c
- Split old freq field into a tv_freq and a radio_freq. Prevents
that a radio tuner is initialized with a tv frequency or vice versa.
- When switching to radio mode initialize the tuner with the last
used radio frequency (this was already done for the TV mode).
As a result of these changes the tuner module now remembers the
last set radio and TV frequencies, which is what you would expect
to happen.
- Move out of range frequencies to the closest valid frequency as per
v4l2 API spec.
- Fix incorrect initial radio frequency (multiplier is 16000, not 16)
- Add boundary check for out of range frequencies.
- Use new flag to check if the order of the CB and freq. depends on
the last set frequency. That is needed for some tuners or you can
get static as a result. The flag is added for those tuners where I know
that the datasheet indicates that this is necessary.
- For this new check use the last set div value, not the last frequency
as radio frequencies are always much higher due to the 16000 multiplier.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following warning which was introduced in 2.6.15-git8 by
commit 7408187d22:
CC [M] drivers/media/video/zoran_card.o
drivers/media/video/zoran_card.c: In function `zr36057_init':
drivers/media/video/zoran_card.c:1053: warning: assignment makes integer from pointer without a cast
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Not sure what went wrong here, but SND_PCI_PM_CALLBACKS got deleted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- BOOT_SIZE name is also used at alpha and were breaking
compiling with allyesconfig.
- All BOOT_* renamed to AV7110_BOOT* to fix and keep names
with the same style.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Workaround to fix a known regression at cx88-tvaudio.c
- provide a module parameter workaround to always enable
analog output.
Signed-off-by: Panagiotis Christeas <p_christ@hol.gr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enabled audio PLL. This is mandatory for NICAM sound
- modify FM IF frequency to 5.5MHz for SAA7133/35 if tuner is tda8290
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add support for Samsung tuner TCPN 2121P30A, used in
Hauppauge PVR-500 cards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tunertype struct redefined to allow one or more tuner_params structs
per tuner definition, one for each video standard.
- Each tuner_params struct has an element containing an arbitrary
amount of tuner_ranges.
(this is needed for dvb tuners - to be handled later)
- A tuner_range may be referenced by multiple tuner_params structs.
There are many duplicates in here. Reusing tuner_range structs,
rather than defining new ones for each tuner, will cut down on
memory usage, and is preferred when possible.
- tunertype struct contains an element, has_tda988x.
We must set this for all tunertypes that contain a tda988x
chip, and then we can remove this setting from the various
card structs.
- Improves tuners array memory usage efficiency.
- Right now, all tuners are using the first tuner_params[] array element
for analog mode. In the future, we will be merging similar tuner
definitions together, such that each tuner definition will have a
tuner_params struct for each available video standard. At that point,
the tuner_params[] array element will be chosen based on the video
standard in use.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static vars are equal to zero by default. Removed unnecessary =0 from them,
saving some data space
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- There's no reason for an ALSA driver to select an OSS legacy userspace
interface.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Adds suppport or fix support for VIDIOC_ENUMSTD, VIDIOC_ENUMINPUT,
VIDIOC_G_TUNER and VIDIOC_S_TUNER.
- Fix the warnings at compile time and add checks for the pointer validity
using access_ok().
- v4l_print_ioctl() has also be added to identify possible missing ioctls.
- Has been tested on sparc64 and amd64. Other arches such as mips and hppa
are expected to work as sparc, but not tested yet.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added knc1 tv star dvb-s support with philips tuner sd1878.
Signed-off-by: Regis Prevot <regis.prevot@anevia.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added USB ID for DigitalNow DVB-T Dual USB,
DViCO FusionHDTV DVB-T Dual USB clone
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
