blk_mq_alloc_request() may establish REQ_MQ_INFLIGHT in addition to
incrementing the hctx->nr_active count. Any cmd_flags that are
established in the newly allocated clone request must be preserved in
addition to the cmd_flags that are later copied over from the original
request as part of blk_rq_prep_clone().
Otherwise, if REQ_MQ_INFLIGHT isn't set in the clone request the
hctx->nr_active count won't get decremented via blk_mq_free_request().
The only consumer of blk_rq_prep_clone() is request-based DM, which uses
blk_rq_init() prior to calling blk_rq_prep_clone() for the non-blk-mq
case. Given the cloned request's cmd_flags will be 0 it is safe to OR
them with the original request's cmd_flags for both the non-blk-mq and
blk-mq cases.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the request passed to blk_insert_cloned_request() was allocated by
a blk-mq device it must be submitted using blk_mq_insert_request().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Prepare to allow blk_rq_prep_clone() to accept clone requests that were
allocated from blk-mq request queues. As such the blk_rq_prep_clone()
caller must first initialize the clone request.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is the blk-mq part to support tag allocation policy. The default
allocation policy isn't changed (though it's not a strict FIFO). The new
policy is round-robin for libata. But it's a try-best implementation. If
multiple tasks are competing, the tags returned will be mixed (which is
unavoidable even with !mq, as requests from different tasks can be
mixed in queue)
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The libata tag allocation is using a round-robin policy. Next patch will
make libata use block generic tag allocation, so let's add a policy to
tag allocation.
Currently two policies: FIFO (default) and round-robin.
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As Christoph put it:
Can we just get rid of the warnings? It's fairly annoying as devices
without partitions are perfectly fine and very useful.
Me too I see this message every VM boot for ages on all my
devices. Would love to just remove it. For me a partition-table
is only needed for a booting BIOS, grub, and stuff.
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkdev_issue_discard() will zero a given block range. This is done by
way of explicit writing, thus provisioning or allocating the blocks on
disk.
There are use cases where the desired behavior is to zero the blocks but
unprovision them if possible. The blocks must deterministically contain
zeroes when they are subsequently read back.
This patch adds a flag to blkdev_issue_zeroout() that provides this
variant. If the discard flag is set and a block device guarantees
discard_zeroes_data we will use REQ_DISCARD to clear the block range. If
the device does not support discard_zeroes_data or if the discard
request fails we will fall back to first REQ_WRITE_SAME and then a
regular REQ_WRITE.
Also update the callers of blkdev_issue_zero() to reflect the new flag
and make sb_issue_zeroout() prefer the discard approach.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Hi,
If you can manage to submit an async write as the first async I/O from
the context of a process with realtime scheduling priority, then a
cfq_queue is allocated, but filed into the wrong async_cfqq bucket. It
ends up in the best effort array, but actually has realtime I/O
scheduling priority set in cfqq->ioprio.
The reason is that cfq_get_queue assumes the default scheduling class and
priority when there is no information present (i.e. when the async cfqq
is created):
static struct cfq_queue *
cfq_get_queue(struct cfq_data *cfqd, bool is_sync, struct cfq_io_cq *cic,
struct bio *bio, gfp_t gfp_mask)
{
const int ioprio_class = IOPRIO_PRIO_CLASS(cic->ioprio);
const int ioprio = IOPRIO_PRIO_DATA(cic->ioprio);
cic->ioprio starts out as 0, which is "invalid". So, class of 0
(IOPRIO_CLASS_NONE) is passed to cfq_async_queue_prio like so:
async_cfqq = cfq_async_queue_prio(cfqd, ioprio_class, ioprio);
static struct cfq_queue **
cfq_async_queue_prio(struct cfq_data *cfqd, int ioprio_class, int ioprio)
{
switch (ioprio_class) {
case IOPRIO_CLASS_RT:
return &cfqd->async_cfqq[0][ioprio];
case IOPRIO_CLASS_NONE:
ioprio = IOPRIO_NORM;
/* fall through */
case IOPRIO_CLASS_BE:
return &cfqd->async_cfqq[1][ioprio];
case IOPRIO_CLASS_IDLE:
return &cfqd->async_idle_cfqq;
default:
BUG();
}
}
Here, instead of returning a class mapped from the process' scheduling
priority, we get back the bucket associated with IOPRIO_CLASS_BE.
Now, there is no queue allocated there yet, so we create it:
cfqq = cfq_find_alloc_queue(cfqd, is_sync, cic, bio, gfp_mask);
That function ends up doing this:
cfq_init_cfqq(cfqd, cfqq, current->pid, is_sync);
cfq_init_prio_data(cfqq, cic);
cfq_init_cfqq marks the priority as having changed. Then, cfq_init_prio
data does this:
ioprio_class = IOPRIO_PRIO_CLASS(cic->ioprio);
switch (ioprio_class) {
default:
printk(KERN_ERR "cfq: bad prio %x\n", ioprio_class);
case IOPRIO_CLASS_NONE:
/*
* no prio set, inherit CPU scheduling settings
*/
cfqq->ioprio = task_nice_ioprio(tsk);
cfqq->ioprio_class = task_nice_ioclass(tsk);
break;
So we basically have two code paths that treat IOPRIO_CLASS_NONE
differently, which results in an RT async cfqq filed into a best effort
bucket.
Attached is a patch which fixes the problem. I'm not sure how to make
it cleaner. Suggestions would be welcome.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Tested-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
The blk-mq tagging tries to maintain some locality between CPUs and
the tags issued. The tags are split into groups of words, and the
words may not be fully populated. When searching for a new free tag,
blk-mq may look at partial words, hence it passes in an offset/size
to find_next_zero_bit(). However, it does that wrong, the size must
always be the full length of the number of tags in that word,
otherwise we'll potentially miss some near the end.
Another issue is when __bt_get() goes from one word set to the next.
It bumps the index, but not the last_tag associated with the
previous index. Bump that to be in the range of the new word.
Finally, clean up __bt_get() and __bt_get_word() a bit and get
rid of the goto in there, and the unnecessary 'wrap' variable.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit b4c6a02877 exported the start and unfreeze, but we need
the regular blk_mq_freeze_queue() for the loop conversion.
Signed-off-by: Jens Axboe <axboe@fb.com>
If it's dying, we can't expect new request to complete and come
in an wake up other tasks waiting for requests. So after we
have marked it as dying, wake up everybody currently waiting
for a request. Once they wake, they will retry their allocation
and fail appropriately due to the state of the queue.
Tested-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This reverts commit 52f7eb945f.
The optimization is only really safe for a single queue, otherwise
'bs' and 'bt' can indeed change, and if we don't do a finish_wait()
for each loop, we'll potentially change the wait structure and
corrupt task wait list.
Reported-by: Jan Kara <jack@suse.cz>
Pull block driver core update from Jens Axboe:
"This is the pull request for the core block IO changes for 3.19. Not
a huge round this time, mostly lots of little good fixes:
- Fix a bug in sysfs blktrace interface causing a NULL pointer
dereference, when enabled/disabled through that API. From Arianna
Avanzini.
- Various updates/fixes/improvements for blk-mq:
- A set of updates from Bart, mostly fixing buts in the tag
handling.
- Cleanup/code consolidation from Christoph.
- Extend queue_rq API to be able to handle batching issues of IO
requests. NVMe will utilize this shortly. From me.
- A few tag and request handling updates from me.
- Cleanup of the preempt handling for running queues from Paolo.
- Prevent running of unmapped hardware queues from Ming Lei.
- Move the kdump memory limiting check to be in the correct
location, from Shaohua.
- Initialize all software queues at init time from Takashi. This
prevents a kobject warning when CPUs are brought online that
weren't online when a queue was registered.
- Single writeback fix for I_DIRTY clearing from Tejun. Queued with
the core IO changes, since it's just a single fix.
- Version X of the __bio_add_page() segment addition retry from
Maurizio. Hope the Xth time is the charm.
- Documentation fixup for IO scheduler merging from Jan.
- Introduce (and use) generic IO stat accounting helpers for non-rq
drivers, from Gu Zheng.
- Kill off artificial limiting of max sectors in a request from
Christoph"
* 'for-3.19/core' of git://git.kernel.dk/linux-block: (26 commits)
bio: modify __bio_add_page() to accept pages that don't start a new segment
blk-mq: Fix uninitialized kobject at CPU hotplugging
blktrace: don't let the sysfs interface remove trace from running list
blk-mq: Use all available hardware queues
blk-mq: Micro-optimize bt_get()
blk-mq: Fix a race between bt_clear_tag() and bt_get()
blk-mq: Avoid that __bt_get_word() wraps multiple times
blk-mq: Fix a use-after-free
blk-mq: prevent unmapped hw queue from being scheduled
blk-mq: re-check for available tags after running the hardware queue
blk-mq: fix hang in bt_get()
blk-mq: move the kdump check to blk_mq_alloc_tag_set
blk-mq: cleanup tag free handling
blk-mq: use 'nr_cpu_ids' as highest CPU ID count for hwq <-> cpu map
blk: introduce generic io stat accounting help function
blk-mq: handle the single queue case in blk_mq_hctx_next_cpu
genhd: check for int overflow in disk_expand_part_tbl()
blk-mq: add blk_mq_free_hctx_request()
blk-mq: export blk_mq_free_request()
blk-mq: use get_cpu/put_cpu instead of preempt_disable/preempt_enable
...
The original behaviour is to refuse to add a new page if the maximum
number of segments has been reached, regardless of the fact the page we
are going to add can be merged into the last segment or not.
Unfortunately, when the system runs under heavy memory fragmentation
conditions, a driver may try to add multiple pages to the last segment.
The original code won't accept them and EBUSY will be reported to
userspace.
This patch modifies the function so it refuses to add a page only in case
the latter starts a new segment and the maximum number of segments has
already been reached.
The bug can be easily reproduced with the st driver:
1) set CONFIG_SCSI_MPT2SAS_MAX_SGE or CONFIG_SCSI_MPT3SAS_MAX_SGE to 16
2) modprobe st buffer_kbs=1024
3) #dd if=/dev/zero of=/dev/st0 bs=1M count=10
dd: error writing `/dev/st0': Device or resource busy
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Jet Chen <jet.chen@intel.com>
Cc: Tomas Henzl <thenzl@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
When a CPU is hotplugged, the current blk-mq spews a warning like:
kobject '(null)' (ffffe8ffffc8b5d8): tried to add an uninitialized object, something is seriously wrong.
CPU: 1 PID: 1386 Comm: systemd-udevd Not tainted 3.18.0-rc7-2.g088d59b-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_171129-lamiak 04/01/2014
0000000000000000 0000000000000002 ffffffff81605f07 ffffe8ffffc8b5d8
ffffffff8132c7a0 ffff88023341d370 0000000000000020 ffff8800bb05bd58
ffff8800bb05bd08 000000000000a0a0 000000003f441940 0000000000000007
Call Trace:
[<ffffffff81005306>] dump_trace+0x86/0x330
[<ffffffff81005644>] show_stack_log_lvl+0x94/0x170
[<ffffffff81006d21>] show_stack+0x21/0x50
[<ffffffff81605f07>] dump_stack+0x41/0x51
[<ffffffff8132c7a0>] kobject_add+0xa0/0xb0
[<ffffffff8130aee1>] blk_mq_register_hctx+0x91/0xb0
[<ffffffff8130b82e>] blk_mq_sysfs_register+0x3e/0x60
[<ffffffff81309298>] blk_mq_queue_reinit_notify+0xf8/0x190
[<ffffffff8107cfdc>] notifier_call_chain+0x4c/0x70
[<ffffffff8105fd23>] cpu_notify+0x23/0x50
[<ffffffff81060037>] _cpu_up+0x157/0x170
[<ffffffff810600d9>] cpu_up+0x89/0xb0
[<ffffffff815fa5b5>] cpu_subsys_online+0x35/0x80
[<ffffffff814323cd>] device_online+0x5d/0xa0
[<ffffffff81432485>] online_store+0x75/0x80
[<ffffffff81236a5a>] kernfs_fop_write+0xda/0x150
[<ffffffff811c5532>] vfs_write+0xb2/0x1f0
[<ffffffff811c5f42>] SyS_write+0x42/0xb0
[<ffffffff8160c4ed>] system_call_fastpath+0x16/0x1b
[<00007f0132fb24e0>] 0x7f0132fb24e0
This is indeed because of an uninitialized kobject for blk_mq_ctx.
The blk_mq_ctx kobjects are initialized in blk_mq_sysfs_init(), but it
goes loop over hctx_for_each_ctx(), i.e. it initializes only for
online CPUs. Thus, when a CPU is hotplugged, the ctx for the newly
onlined CPU is registered without initialization.
This patch fixes the issue by initializing the all ctx kobjects
belonging to each queue.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=908794
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Suppose that a system has two CPU sockets, three cores per socket,
that it does not support hyperthreading and that four hardware
queues are provided by a block driver. With the current algorithm
this will lead to the following assignment of CPU cores to hardware
queues:
HWQ 0: 0 1
HWQ 1: 2 3
HWQ 2: 4 5
HWQ 3: (none)
This patch changes the queue assignment into:
HWQ 0: 0 1
HWQ 1: 2
HWQ 2: 3 4
HWQ 3: 5
In other words, this patch has the following three effects:
- All four hardware queues are used instead of only three.
- CPU cores are spread more evenly over hardware queues. For the
above example the range of the number of CPU cores associated
with a single HWQ is reduced from [0..2] to [1..2].
- If the number of HWQ's is a multiple of the number of CPU sockets
it is now guaranteed that all CPU cores associated with a single
HWQ reside on the same CPU socket.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove a superfluous finish_wait() call. Convert the two bt_wait_ptr()
calls into a single call.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliott <elliott@hp.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
What we need is the following two guarantees:
* Any thread that observes the effect of the test_and_set_bit() by
__bt_get_word() also observes the preceding addition of 'current'
to the appropriate wait list. This is guaranteed by the semantics
of the spin_unlock() operation performed by prepare_and_wait().
Hence the conversion of test_and_set_bit_lock() into
test_and_set_bit().
* The wait lists are examined by bt_clear() after the tag bit has
been cleared. clear_bit_unlock() guarantees that any thread that
observes that the bit has been cleared also observes the store
operations preceding clear_bit_unlock(). However,
clear_bit_unlock() does not prevent that the wait lists are examined
before that the tag bit is cleared. Hence the addition of a memory
barrier between clear_bit() and the wait list examination.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliott <elliott@hp.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Jens Axboe <axboe@fb.com>
If __bt_get_word() is called with last_tag != 0, if the first
find_next_zero_bit() fails, if after wrap-around the
test_and_set_bit() call fails and find_next_zero_bit() succeeds,
if the next test_and_set_bit() call fails and subsequently
find_next_zero_bit() does not find a zero bit, then another
wrap-around will occur. Avoid this by introducing an additional
local variable.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliott <elliott@hp.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Jens Axboe <axboe@fb.com>
blk-mq users are allowed to free the memory request_queue.tag_set
points at after blk_cleanup_queue() has finished but before
blk_release_queue() has started. This can happen e.g. in the SCSI
core. The SCSI core namely embeds the tag_set structure in a SCSI
host structure. The SCSI host structure is freed by
scsi_host_dev_release(). This function is called after
blk_cleanup_queue() finished but can be called before
blk_release_queue().
This means that it is not safe to access request_queue.tag_set from
inside blk_release_queue(). Hence remove the blk_sync_queue() call
from blk_release_queue(). This call is not necessary - outstanding
requests must have finished before blk_release_queue() is
called. Additionally, move the blk_mq_free_queue() call from
blk_release_queue() to blk_cleanup_queue() to avoid that struct
request_queue.tag_set gets accessed after it has been freed.
This patch avoids that the following kernel oops can be triggered
when deleting a SCSI host for which scsi-mq was enabled:
Call Trace:
[<ffffffff8109a7c4>] lock_acquire+0xc4/0x270
[<ffffffff814ce111>] mutex_lock_nested+0x61/0x380
[<ffffffff812575f0>] blk_mq_free_queue+0x30/0x180
[<ffffffff8124d654>] blk_release_queue+0x84/0xd0
[<ffffffff8126c29b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8126c140>] kobject_put+0x30/0x70
[<ffffffff81245895>] blk_put_queue+0x15/0x20
[<ffffffff8125c409>] disk_release+0x99/0xd0
[<ffffffff8133d056>] device_release+0x36/0xb0
[<ffffffff8126c29b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8126c140>] kobject_put+0x30/0x70
[<ffffffff8125a78a>] put_disk+0x1a/0x20
[<ffffffff811d4cb5>] __blkdev_put+0x135/0x1b0
[<ffffffff811d56a0>] blkdev_put+0x50/0x160
[<ffffffff81199eb4>] kill_block_super+0x44/0x70
[<ffffffff8119a2a4>] deactivate_locked_super+0x44/0x60
[<ffffffff8119a87e>] deactivate_super+0x4e/0x70
[<ffffffff811b9833>] cleanup_mnt+0x43/0x90
[<ffffffff811b98d2>] __cleanup_mnt+0x12/0x20
[<ffffffff8107252c>] task_work_run+0xac/0xe0
[<ffffffff81002c01>] do_notify_resume+0x61/0xa0
[<ffffffff814d2c58>] int_signal+0x12/0x17
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliott <elliott@hp.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch is the usual mix of driver updates (srp, ipr, scsi_debug, NCR5380,
fnic, 53c974, ses, wd719x, hpsa, megaraid_sas). Of those, wd7a9x is new and
53c974 is a rewrite of the old tmscsim driver and the extensive work by Finn
Thain rewrites all the NCR5380 based drivers. There's also extensive
infrastructure updates: a new logging infrastructure for sense information and
a rewrite of the tagged command queue API and an assortment of minor updates.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUhgazAAoJEDeqqVYsXL0MxIYH/2wCs9sne5cfDTjfufLJDdu1
WLoJgNMxv+14OukknJfG2Kk1WlHgLRM5+TVWIGiG0mmjXuFyShzIqEOHKTDWqxnE
tBH4wLi/+XYqZAmAeim4/2zhvf+cUVVlIu01VERR5uwaBWYM8BeLSwjdnAAvEEwb
iV74p1WV6frXo4guADplgtkjD0YxI4MTUZ1figRMlLO6WLFFyQ+95UfY8jFs+eQv
zk63y7Mm7dQNd57/Wl3i89lw0kqlaJSZNl8Ovj1axy4rDYzT1wXhY8mEwD8fI8Ym
wahldjFE5vXgj0NpO3tB3Z+UDP2YmQduMyzTxkPNnrEPKiOCsnQo42XR6vb92cQ=
=Y+DU
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch is the usual mix of driver updates (srp, ipr, scsi_debug,
NCR5380, fnic, 53c974, ses, wd719x, hpsa, megaraid_sas).
Of those, wd7a9x is new and 53c974 is a rewrite of the old tmscsim
driver and the extensive work by Finn Thain rewrites all the NCR5380
based drivers.
There's also extensive infrastructure updates: a new logging
infrastructure for sense information and a rewrite of the tagged
command queue API and an assortment of minor updates"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (183 commits)
scsi: set fmt to NULL scsi_extd_sense_format() by default
libsas: remove task_collector mode
wd719x: remove dma_cache_sync call
scsi_debug: add Report supported opcodes+tmfs; Compare and write
scsi_debug: change SCSI command parser to table driven
scsi_debug: add Capacity Changed Unit Attention
scsi_debug: append inject error flags onto scsi_cmnd object
scsi_debug: pinpoint invalid field in sense data
wd719x: Add firmware documentation
wd719x: Introduce Western Digital WD7193/7197/7296 PCI SCSI card driver
eeprom-93cx6: Add (read-only) support for 8-bit mode
esas2r: fix an oversight in setting return value
esas2r: fix an error path in esas2r_ioctl_handler
esas2r: fir error handling in do_fm_api
scsi: add SPC-3 command definitions
scsi: rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16
scsi: remove scsi_driver owner field
scsi: move scsi_dispatch_cmd to scsi_lib.c
scsi: stop passing a gfp_mask argument down the command setup path
scsi: remove scsi_next_command
...
When one hardware queue has no mapped software queues, it
shouldn't have been scheduled. Otherwise WARNING or OOPS
can triggered.
blk_mq_hw_queue_mapped() helper is introduce for fixing
the problem.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If we run out of tags and have to sleep, we run the hardware queue
to kick pending IO into gear. During that run, we may have completed
requests, so re-check if we have free tags before going to sleep.
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid that if there are fewer hardware queues than CPU threads that
bt_get() can hang. The symptoms of the hang were as follows:
* All tags allocated for a particular hardware queue.
* (nr_tags) pending commands for that hardware queue.
* No pending commands for the software queues associated with that
hardware queue.
Signed-off-by: Jens Axboe <axboe@fb.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the block device core.
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
bio integrity handling is broken on a system with LVM layered atop a
DIF/DIX SCSI drive because device mapper clones the bio, modifies the
clone, and sends the clone to the lower layers for processing.
However, the clone bio has bi_vcnt == 0, which means that when the sd
driver calls bio_integrity_process to attach DIX data, the
for_each_segment_all() call (which uses bi_vcnt) returns immediately
and random garbage is sent to the disk on a disk write. The disk of
course returns an error.
Therefore, teach bio_integrity_process() to use bio_for_each_segment()
to iterate the bio_vecs, since the per-bio iterator tracks which
bio_vecs are associated with that particular bio. The integrity
handling code is effectively part of the "driver" (it's not the bio
owner), so it must use the correct iterator function.
v2: Fix a compiler warning about abandoned local variables. This
patch supersedes "block: bio_integrity_process uses wrong bio_vec
iterator". Patch applies against 3.18-rc6.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We call blk_mq_alloc_tag_set() first then blk_mq_init_queue(). The requests are
allocated in the former function. So the kdump check should be moved to there
to really save memory.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We only call __blk_mq_put_tag() and __blk_mq_put_reserved_tag()
from blk_mq_put_tag(), so just inline the two calls instead of
having them as separate functions.
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently use num_possible_cpus(), but that breaks on sparc64 where
the CPU ID space is discontig. Use nr_cpu_ids as the highest CPU ID
instead, so we don't end up reading from invalid memory.
Cc: stable@kernel.org # 3.13+
Signed-off-by: Jens Axboe <axboe@fb.com>
SPC-3 defines SERVICE ACTION IN(12) and SERVICE ACTION IN(16).
So rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16 to be
consistent with SPC and to allow for better distinction.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Many block drivers accounting io stat based on bio (e.g. NVMe...),
the blk_account_io_start/end() which is based on request
does not make sense to them, so here we introduce the similar help
function named generic_start/end_io_acct base on raw sectors, and it can
simplify some driver's open io accounting code.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't duplicate the code to handle the not cpu bounce case in the
caller, do it inside blk_mq_hctx_next_cpu instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can get here from blkdev_ioctl() -> blkpg_ioctl() -> add_partition()
with a user passed in partno value. If we pass in 0x7fffffff, the
new target in disk_expand_part_tbl() overflows the 'int' and we
access beyond the end of ptbl->part[] and even write to it when we
do the rcu_assign_pointer() to assign the new partition.
Reported-by: David Ramos <daramos@stanford.edu>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
It's silly to use blk_mq_free_request() which in turn maps the
request to the hardware queue, for places where we already know
what the hardware queue is. This saves us an extra mapping of a
hardware queue on request completion, if the caller knows this
information already.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The queuecommand() callback functions in SCSI low-level drivers
need to know which hardware context has been selected by the
block layer. Since this information is not available in the
request structure, and since passing the hctx pointer directly to
the queuecommand callback function would require modification of
all SCSI LLDs, add a function to the block layer that allows to
query the hardware context index.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For cloned bio, bio->bi_vcnt can't be used at all, and we
have resort to bio_segments() to figure out how many
segment there are in the bio.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk-mq is using preempt_disable/enable in order to ensure that the
queue runners are placed on the right CPU. This does not work with
the RT patches, because __blk_mq_run_hw_queue takes a non-raw
spinlock with the preemption-disabled region. If there is contention
on the lock, this violates the rules for preemption-disabled regions.
While this should be easily fixable within the RT patches just by doing
migrate_disable/enable, we can do better and document _why_ this
particular region runs with disabled preemption. After the previous
patch, it is trivial to switch it to get/put_cpu; the RT patches then
can change it to get_cpu_light, which lets virtio-blk run under RT
kernels.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Clark Williams <williams@redhat.com>
Tested-by: Clark Williams <williams@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
preempt_disable/enable surrounds every call to blk_mq_run_hw_queue,
except the one in blk-flush.c. In fact that one is always asynchronous,
and it does not need smp_processor_id().
We can do the same for all other calls, avoiding preempt_disable when
async is true. This avoids peppering blk-mq.c with preemption-disabled
regions.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Clark Williams <williams@redhat.com>
Tested-by: Clark Williams <williams@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix an error path in SCSI_IOCTL_SEND_COMMAND that calls
blk_put_request(rq) on an invalid IS_ERR(rq) pointer.
Fixes: a492f07545 ("block,scsi: fixup blk_get_request dead queue scenarios")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
q->mq_usage_counter is a percpu_ref which is killed and drained when
the queue is frozen. On a CPU hotplug event, blk_mq_queue_reinit()
which involves freezing the queue is invoked on all existing queues.
Because percpu_ref killing and draining involve a RCU grace period,
doing the above on one queue after another may take a long time if
there are many queues on the system.
This patch splits out initiation of freezing and waiting for its
completion, and updates blk_mq_queue_reinit_notify() so that the
queues are frozen in parallel instead of one after another. Note that
freezing and unfreezing are moved from blk_mq_queue_reinit() to
blk_mq_queue_reinit_notify().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Priority of a merged request is computed by ioprio_best(). If one of the
requests has undefined priority (IOPRIO_CLASS_NONE) and another request
has priority from IOPRIO_CLASS_BE, the function will return the
undefined priority which is wrong. Fix the function to properly return
priority of a request with the defined priority.
Fixes: d58cdfb89c
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Drivers can now tell blk-mq if they take advantage of the deferred
issue through 'last' or not. If they do, don't do queue-direct
for sync IO. This is a preparation patch for the nvme conversion.
Signed-off-by: Jens Axboe <axboe@fb.com>
Since we have the notion of a 'last' request in a chain, we can use
this to have the hardware optimize the issuing of requests. Add
a list_head parameter to queue_rq that the driver can use to
temporarily store hw commands for issue when 'last' is true. If we
are doing a chain of requests, pass in a NULL list for the first
request to force issue of that immediately, then batch the remainder
for deferred issue until the last request has been sent.
Instead of adding yet another argument to the hot ->queue_rq path,
encapsulate the passed arguments in a blk_mq_queue_data structure.
This is passed as a constant, and has been tested as faster than
passing 4 (or even 3) args through ->queue_rq. Update drivers for
the new ->queue_rq() prototype. There are no functional changes
in this patch for drivers - if they don't use the passed in list,
then they will just queue requests individually like before.
Signed-off-by: Jens Axboe <axboe@fb.com>
