Add "reset-post-delay-us" parameter to MDIO bus properties,
so it's possible to add a delay after reset deassert.
This is optional in case external hardware slows down
release of the reset signal.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now skb->dev is unconditionally set to the loopback device in current net
namespace. But if we want to test bpf program which contains code branch
based on ifindex condition (eg filters out localhost packets) it is useful
to allow specifying of ifindex from userspace. This patch adds such option
through ctx_in (__sk_buff) parameter.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200803090545.82046-3-zeil@yandex-team.ru
Now it's impossible to test all branches of cgroup_skb bpf program which
accesses skb->family and skb->{local,remote}_ip{4,6} fields because they
are zeroed during socket allocation. This commit fills socket family and
addresses from related fields in constructed skb.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200803090545.82046-2-zeil@yandex-team.ru
Allocate nic_info dynamically - n_entries is not constant.
Attach the tunnel offload info only to the uplink representor.
We expect the "main" netdev to be unregistered in switchdev
mode, and there to be only one uplink representor.
Drop the udp_tunnel_drop_rx_info() call, it was not there until
commit b3c2ed21c0 ("net/mlx5e: Fix VXLAN configuration restore after function reload")
so the device doesn't need it, and core should handle reloads and
reset just fine.
v2:
- don't drop the ndos on reprs, and register info on uplink repr.
v4:
- Move netdev tunnel structure handling to en_main.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The DR TX state machine supports the following order:
modify header, push vlan and encapsulation.
Instead fs_dr would pass:
push vlan, modify header and encapsulation.
The above caused the rule creation to fail on invalid action
sequence provided error.
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently PF and VF representor netdevice carrier is always controlled
by controlling the representor netdevice device state as up/down.
Representor netdevice state change undergoes one or more txq/rxq
destroy/create commands to firmware, skb and its rx buffer allocation,
health reporters creation and more.
Due to this limitation users do not have the ability to just change
the carrier of the non uplink representors without modifying the
device state.
In one use case when the eswitch physical port carrier is down/up,
user needs to update the VF link state to same as physical port
carrier.
Example of updating VF representor carrier state:
$ ip link set enp0s8f0npf0vf0 carrier off
$ ip link set enp0s8f0npf0vf0 carrier on
This enhancement results into VF link state change which is
represented by the VF representor netdevice carrier.
This enables users to modify the representor carrier without modifying
the representor netdevice state.
A simple test is run using [1] to calculate the time difference between
updating carrier vs updating device state (to update just the carrier)
with one VF to simulate 255 VFs.
Time taken to update the carrier using device up/down:
$ time ./calculate.sh dev enp0s8f0npf0vf0
real 0m30.913s
user 0m0.200s
sys 0m11.168s
Time taken to update just the carrier using carrier iproute2 command:
$ time ./calculate.sh carrier enp0s8f0npf0vf0
real 0m2.142s
user 0m0.160s
sys 0m2.021s
Test shows that its better to use carrier on/off user interface to notify
link up/down event to VF compare to device up/down interface, because
carrier user interface delivers the same event 15 times faster.
[1] https://github.com/paravmellanox/myscripts/blob/master/calculate_carrier_time.sh
Signed-off-by: Parav Pandit <parav@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Andrii Nakryiko says:
====================
It's pretty common for applications to want to parse raw (binary) BTF data
from file, as opposed to parsing it from ELF sections. It's also pretty common
for tools to not care whether given file is ELF or raw BTF format. This patch
series exposes internal raw BTF parsing API and adds generic variant of BTF
parsing, which will efficiently determine the format of a given fail and will
parse BTF appropriately.
Patches #2 and #3 removes re-implementations of such APIs from bpftool and
resolve_btfids tools.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use generic libbpf API to parse BTF data from file, instead of re-implementing
it in bpftool.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200802013219.864880-3-andriin@fb.com
Add public APIs to parse BTF from raw data file (e.g.,
/sys/kernel/btf/vmlinux), as well as generic btf__parse(), which will try to
determine correct format, currently either raw or ELF.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200802013219.864880-2-andriin@fb.com
In case of btf_id does not exist, a negative error code -ENOENT
should be returned.
Fixes: c93cc69004 ("bpftool: add ability to dump BTF types")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200802111540.5384-1-tianjia.zhang@linux.alibaba.com
The '&&' command seems to have a bad effect when $(cmd_$(1)) exits with
non-zero effect: the command failure is masked (despite `set -e`) and all but
the first command of $(dep-cmd) is executed (successfully, as they are mostly
printfs), thus overall returning 0 in the end.
This means in practice that despite compilation errors, tools's build Makefile
will return success. We see this very reliably with libbpf's Makefile, which
doesn't get compilation error propagated properly. This in turns causes issues
with selftests build, as well as bpftool and other projects that rely on
building libbpf.
The fix is simple: don't use &&. Given `set -e`, we don't need to chain
commands with &&. The shell will exit on first failure, giving desired
behavior and propagating error properly.
Fixes: 275e2d9559 ("tools build: Move dependency copy into function")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/bpf/20200731024244.872574-1-andriin@fb.com
mac80211.h says: Beacon filter support is advertised with the
IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to
enable beacon filter support whenever power save is enabled, that is
IEEE80211_CONF_PS is set. When power save is enabled, the stack will
not check for beacon loss and the driver needs to notify about loss
of beacons with ieee80211_beacon_loss().
Some controllers may want to dynamically enable the beacon filter
capabilities on power save entry (CONF_PS) and disable it on exit.
This is the case for the wcn36xx driver which only supports beacon
filtering in PS mode (no CONNECTION_MONITOR support).
When the mac80211 beacon monitor timer expires, the beacon filter
flag must be checked again in case it as been changed in between
(e.g. vif moved to PS mode).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sparse showed up with the following error.
net/mac80211/agg-rx.c:480:43: warning: Using plain integer as NULL pointer
Fixes: 2ab4587675 (mac80211: add support for the ADDBA extension element)
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200803084540.179908-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK
(WFA) options. Those extensions use special status code values in the
SAE commit messages (Authentication frame with transaction sequence
number 1) to identify which extension is in use. mac80211 was
interpreting those new values as the AP denying authentication and that
resulted in failure to complete SAE authentication in some cases.
Fix this by adding exceptions for the new status code values 126 and
127.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace EBUSY by EEXIST in the following cases:
- If the user adds a chain with a different configuration such as different
type, hook and priority.
- If the user adds a non-base chain that clashes with an existing basechain.
- If the user adds a { key : value } mapping element and the key exists
but the value differs.
- If the device already belongs to an existing flowtable.
User describe that this error reporting is confusing:
- https://bugzilla.netfilter.org/show_bug.cgi?id=1176
- https://bugzilla.netfilter.org/show_bug.cgi?id=1413
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112302.22718-1-nsaenzjulienne@suse.de
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722111725.210923-1-linus.walleij@linaro.org
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bcma/scan.c: In function 'bcma_erom_get_addr_desc':
drivers/bcma/scan.c:219 warning:
variable `addrh` and `sizeh` set but not used [-Wunused-but-set-variable]
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721083935.13306-1-zhengyongjun3@huawei.com
wl1251_event_ps_report() should not always return 0 because
wl1251_ps_set_mode() may fail. Change it to return 'ret'.
Fixes: f7ad1eed4d ("wl1251: retry power save entry")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730073939.33704-1-wanghai38@huawei.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200728114128.1218310-1-vaibhavgupta40@gmail.com
In some Intersil files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723135254.594984-1-f.suligoi@asem.it
Add the missing platform_device_unregister() before return from
qtnf_core_mac_alloc() in the error handling case.
Fixes: 616f5701f4 ("qtnfmac: assign each wiphy to its own virtual platform device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730064910.37589-1-wanghai38@huawei.com
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'ipw2100_msg_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_msg_allocate
Moreover, 'ipw2100_msg_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'status_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> status_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'bd_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> bd_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw2100_tx_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
Moreover, 'ipw2100_tx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw_queue_tx_init()' (ipw2200.c),
GFP_KERNEL can be used because it is called from a call chain that already
uses GFP_KERNEL and no spin_lock is taken in the between.
The call chain is:
ipw_up
--> ipw_load
--> ipw_queue_reset
--> ipw_queue_tx_init
'ipw_up()' already uses GFP_KERNEL for some other memory allocations.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101716.26185-1-christophe.jaillet@wanadoo.fr
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
No lock is taken in the between.
So it is safe to use GFP_KERNEL in 'ipw2100_tx_allocate()'.
BTW, 'ipw2100_queues_allocate()' also calls 'ipw2100_msg_allocate()' which
already allocates some memory using GFP_KERNEL.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101701.26126-1-christophe.jaillet@wanadoo.fr
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721150547.371763-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719111124.58167-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719110115.58085-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718100240.98593-1-grandmaster@al2klimov.de
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
The callbacks make use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device() and
pci_set_power_state() to do required operations. In generic mode, they are
no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
The .suspend() callback is invoking rt2x00lib_suspend() which needs to be
modified as generic rt2x00pci_suspend() has no pm_message_t type argument,
passed to it, which is required by it according to its declaration.
Although this variable remained unused in the function body. Hence, remove
it from the function definition & declaration.
rt2x00lib_suspend() is also invoked by rt2x00usb_suspend() and
rt2x00soc_suspend(). Thus, modify the functional call accordingly in their
function body.
Earlier, .suspend() & .resume() were exported and were used by the
following drivers:
- drivers/net/wireless/ralink/rt2x00/rt2400pci.c
- drivers/net/wireless/ralink/rt2x00/rt2500pci.c
- drivers/net/wireless/ralink/rt2x00/rt2800pci.c
- drivers/net/wireless/ralink/rt2x00/rt61pci.c
Now, we only need to bind "struct dev_pm_ops" variable to
"struct pci_driver". Thus, make the callbacks static. Declare an
"extern const struct dev_pm_ops" variable and bind PM callbacks to it. Now,
export the variable instead and use it in respective drivers.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717110928.454867-1-vaibhavgupta40@gmail.com
Moved macros used for Vendor/Device ID from wilc1000 driver to common
header file and changed macro name for consistency with other macros.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717051134.19160-1-ajay.kathat@microchip.com
In the implementation of mt7601u_mcu_msg_send(), skb is supposed to be
consumed on all execution paths. Release skb before returning if
test_bit() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718052630.11032-1-navid.emamdoost@gmail.com
Missing this firmware is not fatal, my wifi card still works. Even more,
I couldn't find any documentation what it is or where to get it. So, I
don't think the users should be notified if it is missing. If you browse
the net, you see the message is present is in quite some logs. Better
remove it.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200625165210.14904-1-wsa@kernel.org
Without this patch, RTL8821CE will not have coex support,
and will crash the system because of the NULL pointers
for the coex functions.
While RTL8822C series are WiFi + BT combo chips, it needs
the co-existence mechanism for the device to work on both
WiFi and BT without interfering each other. And the coex
support has already been added before, most of the mechanisms
are implemented. The driver should just add corresponding
functions to operate on different types of chips and its
coex parameters.
Fixes: f745eb9ca5 ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Signed-off-by: Ping-Cheng Chen <pc.chen@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724054208.31115-1-yhchuang@realtek.com
The sparse tool complains as follows:
drivers/net/wireless/realtek/rtw88/rtw8821c.c:1374:32: warning:
symbol 'rtw8821c_rtw_pwr_track_tbl' was not declared. Should it be static?
This variable is not used outside of rtw8821c.c, so this commit
marks it static.
Fixes: 3a4312828c ("rtw88: 8821c: add power tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721134901.33968-1-weiyongjun1@huawei.com
It's very useful to send H2C command for debug usage. Add an entry
for sending H2C command to firmware.
usage example:
echo 42,00,00,43,02,00,00,00 > /sys/kernel/debug/ieee80211/phyX/rtw88
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-8-yhchuang@realtek.com
Sometimes mac80211 will just ask driver to change the interface
instead of to remove and then add a new one. And for driver, to
change the interface is just simply to remove and add a new one
but change the type of it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-6-yhchuang@realtek.com
The coex mechanism used to skip upon the freeze flag is raised.
That will cause the coex mechanism being skipped unexpectedly.
Coex only wanted to keep the TDMA table from being changed by
BT side.
So, check the freeze and reason, if the coex reason is coming
from BT info, skip it, to make sure the coex triggered by Wifi
itself can work.
This is required for the AP mode, while the control flow is
different with STA mode. When starting an AP mode, the AP mode
needs to start working immedaitely after leaving IPS, and the
freeze flag could be raised. If the coex info is skipped, then
the AP mode will not set the antenna owner, leads to TX stuck.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-5-yhchuang@realtek.com
Previous settings for TX descriptors of and reserved page packets
are insufficient.
For the sequence number of packets downloaded to reserved page, it
should be filled by hardware.
And for ps-poll packets in reserved page, to prevent AID being
changed by hardware, NAVUSEHDR should be set.
Additionally, the rate should be adjusted based on the current band
for mgmt and reserved page packets.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-4-yhchuang@realtek.com
Fix the transmission is not sent with short GI under
some conditions even if the receiver supports short GI.
If VHT capability IE exists in the beacon, the original
code uses the short GI for 80M field as driver's short GI
setting for transmission, even the current bandwidth is
not 80MHz.
Short GI supported fields for 20M/40M are informed in HT
capability information element, and short GI supported
field for 80M is informed in VHT capability information
element.
These three fields may be set to different values.
Driver needs to record each short GI support field for
each bandwidth, and send correct info depends on current
bandwidth to the WiFi firmware.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-3-yhchuang@realtek.com
Convert the type of LDPC field to boolen because
LDPC field of RA info H2C command to firmware
is only one bit.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-2-yhchuang@realtek.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721125514.145607-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719121224.58581-1-grandmaster@al2klimov.de