* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add kprobe_insn_mutex for protecting kprobe_insn_pages hlist, and remove
kprobe_mutex from architecture dependent code.
This allows us to call arch_remove_kprobe() (and free_insn_slot) while
holding kprobe_mutex.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show node to memory section relationship with symlinks in sysfs
Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX. For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.
Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.
In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
- Provides information needed to determine the specific node
on which a defective DIMM is located. This will reduce system
downtime when the node or defective DIMM is swapped out.
- Prevents unintended onlining of a memory section that was
previously offlined due to a defective DIMM. This could happen
during node hot-add when the user or node hot-add assist script
onlines _all_ offlined sections due to user or script inability
to identify the specific memory sections located on the hot-added
node. The consequences of reintroducing the defective memory
could be ugly.
- Provides information needed to vary the amount and distribution
of memory on specific nodes for testing or debugging purposes.
Future:
- Will provide information needed to identify the memory
sections that need to be offlined prior to physical removal
of a specific node.
Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems. Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The KernelPageSize entry in /proc/pid/smaps is the pagesize used by the
kernel to back a VMA. This matches the size used by the MMU in the
majority of cases. However, one counter-example occurs on PPC64 kernels
whereby a kernel using 64K as a base pagesize may still use 4K pages for
the MMU on older processor. To distinguish, this patch reports
MMUPageSize as the pagesize used by the MMU in /proc/pid/smaps.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: "KOSAKI Motohiro" <kosaki.motohiro@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misspelling of "firmware" in powerpc Makefile
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (140 commits)
KVM: MMU: handle large host sptes on invlpg/resync
KVM: Add locking to virtual i8259 interrupt controller
KVM: MMU: Don't treat a global pte as such if cr4.pge is cleared
MAINTAINERS: Maintainership changes for kvm/ia64
KVM: ia64: Fix kvm_arch_vcpu_ioctl_[gs]et_regs()
KVM: x86: Rework user space NMI injection as KVM_CAP_USER_NMI
KVM: VMX: Fix pending NMI-vs.-IRQ race for user space irqchip
KVM: fix handling of ACK from shared guest IRQ
KVM: MMU: check for present pdptr shadow page in walk_shadow
KVM: Consolidate userspace memory capability reporting into common code
KVM: Advertise the bug in memory region destruction as fixed
KVM: use cpumask_var_t for cpus_hardware_enabled
KVM: use modern cpumask primitives, no cpumask_t on stack
KVM: Extract core of kvm_flush_remote_tlbs/kvm_reload_remote_mmus
KVM: set owner of cpu and vm file operations
anon_inodes: use fops->owner for module refcount
x86: KVM guest: kvm_get_tsc_khz: return khz, not lpj
KVM: MMU: prepopulate the shadow on invlpg
KVM: MMU: skip global pgtables on sync due to cr3 switch
KVM: MMU: collapse remote TLB flushes on root sync
...
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
struct dentry is one of the most critical structures in the kernel. So it's
sad to see it going neglected.
With CONFIG_PROFILING turned on (which is probably the common case at least
for distros and kernel developers), sizeof(struct dcache) == 208 here
(64-bit). This gives 19 objects per slab.
I packed d_mounted into a hole, and took another 4 bytes off the inline
name length to take the padding out from the end of the structure. This
shinks it to 200 bytes. I could have gone the other way and increased the
length to 40, but I'm aiming for a magic number, read on...
I then got rid of the d_cookie pointer. This shrinks it to 192 bytes. Rant:
why was this ever a good idea? The cookie system should increase its hash
size or use a tree or something if lookups are a problem. Also the "fast
dcookie lookups" in oprofile should be moved into the dcookie code -- how
can oprofile possibly care about the dcookie_mutex? It gets dropped after
get_dcookie() returns so it can't be providing any sort of protection.
At 192 bytes, 21 objects fit into a 4K page, saving about 3MB on my system
with ~140 000 entries allocated. 192 is also a multiple of 64, so we get
nice cacheline alignment on 64 and 32 byte line systems -- any given dentry
will now require 3 cachelines to touch all fields wheras previously it
would require 4.
I know the inline name size was chosen quite carefully, however with the
reduction in cacheline footprint, it should actually be just about as fast
to do a name lookup for a 36 character name as it was before the patch (and
faster for other sizes). The memory footprint savings for names which are
<= 32 or > 36 bytes long should more than make up for the memory cost for
33-36 byte names.
Performance is a feature...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only significant changes were to kvmppc_exit_timing_write() and
kvmppc_exit_timing_show(), both of which were dramatically simplified.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Existing KVM statistics are either just counters (kvm_stat) reported for
KVM generally or trace based aproaches like kvm_trace.
For KVM on powerpc we had the need to track the timings of the different exit
types. While this could be achieved parsing data created with a kvm_trace
extension this adds too much overhead (at least on embedded PowerPC) slowing
down the workloads we wanted to measure.
Therefore this patch adds a in-kernel exit timing statistic to the powerpc kvm
code. These statistic is available per vm&vcpu under the kvm debugfs directory.
As this statistic is low, but still some overhead it can be enabled via a
.config entry and should be off by default.
Since this patch touched all powerpc kvm_stat code anyway this code is now
merged and simplified together with the exit timing statistic code (still
working with exit timing disabled in .config).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Store shadow TLB entries in memory, but only use it on host context switch
(instead of every guest entry). This improves performance for most workloads on
440 by reducing the guest TLB miss rate.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Formerly, we used to maintain a per-vcpu shadow TLB and on every entry to the
guest would load this array into the hardware TLB. This consumed 1280 bytes of
memory (64 entries of 16 bytes plus a struct page pointer each), and also
required some assembly to loop over the array on every entry.
Instead of saving a copy in memory, we can just store shadow mappings directly
into the hardware TLB, accepting that the host kernel will clobber these as
part of the normal 440 TLB round robin. When we do that we need less than half
the memory, and we have decreased the exit handling time for all guest exits,
at the cost of increased number of TLB misses because the host overwrites some
guest entries.
These savings will be increased on processors with larger TLBs or which
implement intelligent flush instructions like tlbivax (which will avoid the
need to walk arrays in software).
In addition to that and to the code simplification, we have a greater chance of
leaving other host userspace mappings in the TLB, instead of forcing all
subsequent tasks to re-fault all their mappings.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM currently ignores the host's round robin TLB eviction selection, instead
maintaining its own TLB state and its own round robin index. However, by
participating in the normal 44x TLB selection, we can drop the alternate TLB
processing in KVM. This results in a significant performance improvement,
since that processing currently must be done on *every* guest exit.
Accordingly, KVM needs to be able to access and increment tlb_44x_index.
(KVM on 440 cannot be a module, so there is no need to export this symbol.)
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM on 440 has always been able to handle large guest mappings with 4K host
pages -- we must, since the guest kernel uses 256MB mappings.
This patch makes KVM work when the host has large pages too (tested with 64K).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We used to defer invalidating userspace TLB entries until jumping out of the
kernel. This was causing MMU weirdness most easily triggered by using a pipe in
the guest, e.g. "dmesg | tail". I believe the problem was that after the guest
kernel changed the PID (part of context switch), the old process's mappings
were still present, and so copy_to_user() on the "return to new process" path
ended up using stale mappings.
Testing with large pages (64K) exposed the problem, probably because with 4K
pages, pressure on the TLB faulted all process A's mappings out before the
guest kernel could insert any for process B.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Bare metal Linux on 440 can "overmap" RAM in the kernel linear map, so that it
can use large (256MB) mappings even if memory isn't a multiple of 256MB. To
prevent the hardware prefetcher from loading from an invalid physical address
through that mapping, it's marked Guarded.
However, KVM must ensure that all guest mappings are backed by real physical
RAM (since a deliberate access through a guarded mapping could still cause a
machine check). Accordingly, we don't need to make our mappings guarded, so
let's allow prefetching as the designers intended.
Curiously this patch didn't affect performance at all on the quick test I
tried, but it's clearly the right thing to do anyways and may improve other
workloads.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make sure that CONFIG_KVM cannot be selected without processor support
(currently, 440 is the only processor implementation available).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
set ESR[PTR] when emulating a guest trap. This allows Linux guests to
properly handle WARN_ON() (i.e. detect that it's a non-fatal trap).
Also remove debugging printk in trap emulation.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In kvmppc_deliver_interrupt is just one case left in the switch and it is a
rare one (less than 8%) when looking at the exit numbers. Therefore we can
at least drop the switch/case and if an if. I inserted an unlikely too, but
that's open for discussion.
In kvmppc_can_deliver_interrupt all frequent cases are in the default case.
I know compilers are smart but we can make it easier for them. By writing
down all options and removing the default case combined with the fact that
ithe values are constants 0..15 should allow the compiler to write an easy
jump table.
Modifying kvmppc_can_deliver_interrupt pointed me to the fact that gcc seems
to be unable to reduce priority_exception[x] to a build time constant.
Therefore I changed the usage of the translation arrays in the interrupt
delivery path completely. It is now using priority without translation to irq
on the full irq delivery path.
To be able to do that ivpr regs are stored by their priority now.
Additionally the decision made in kvmppc_can_deliver_interrupt is already
sufficient to get the value of interrupt_msr_mask[x]. Therefore we can replace
the 16x4byte array used here with a single 4byte variable (might still be one
miss, but the chance to find this in cache should be better than the right
entry of the whole array).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we use a unsigned long here anyway we can use the optimized __ffs.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we use an unnecessary if&switch to detect some cases.
To be honest we don't need the ligh_exits counter anyway, because we can
calculate it out of others. Sum_exits can also be calculated, so we can
remove that too.
MMIO, DCR and INTR can be counted on other places without these
additional control structures (The INTR case was never hit anyway).
The handling of BOOKE_INTERRUPT_EXTERNAL/BOOKE_INTERRUPT_DECREMENTER is
similar, but we can avoid the additional if when copying 3 lines of code.
I thought about a goto there to prevent duplicate lines, but rewriting three
lines should be better style than a goto cross switch/case statements (its
also not enough code to justify a new inline function).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When changing some msr bits e.g. problem state we need to take special
care of that. We call the function in our mtmsr emulation (not needed for
wrtee[i]), but we don't call kvmppc_set_msr if we change msr via set_regs
ioctl.
It's a corner case we never hit so far, but I assume it should be
kvmppc_set_msr in our arch set regs function (I found it because it is also
a corner case when using pv support which would miss the update otherwise).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
However, some of these fields could be split into separate per-core structures
in the future.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch doesn't yet move all 44x-specific data into the new structure, but
is the first step down that path. In the future we may also want to create a
struct kvm_vcpu_booke.
Based on patch from Liu Yu <yu.liu@freescale.com>.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cores provide 3 emulation hooks, implemented for example in the new
4xx_emulate.c:
kvmppc_core_emulate_op
kvmppc_core_emulate_mtspr
kvmppc_core_emulate_mfspr
Strictly speaking the last two aren't necessary, but provide for more
informative error reporting ("unknown SPR").
Long term I'd like to have instruction decoding autogenerated from tables of
opcodes, and that way we could aggregate universal, Book E, and core-specific
instructions more easily and without redundant switch statements.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is used in a couple places in KVM, but isn't KVM-specific.
However, this patch doesn't modify other in-kernel emulation code:
- xmon uses a direct copy of ppc_opc.c from binutils
- emulate_instruction() doesn't need it because it can use a series
of mask tests.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This introduces a set of core-provided hooks. For 440, some of these are
implemented by booke.c, with the rest in (the new) 44x.c.
Note that these hooks are link-time, not run-time. Since it is not possible to
build a single kernel for both e500 and 440 (for example), using function
pointers would only add overhead.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The division was somewhat artificial and cumbersome, and had no functional
benefit anyways: we can only guests built for the real host processor.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will ease ports to other cores.
Also remove unused "struct kvm_tlb" while we're at it.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will make it easier to provide implementations for other cores.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The cpu time spent by the idle process actually doing something is
currently accounted as idle time. This is plain wrong, the architectures
that support VIRT_CPU_ACCOUNTING=y can do better: distinguish between the
time spent doing nothing and the time spent by idle doing work. The first
is accounted with account_idle_time and the second with account_system_time.
The architectures that use the account_xxx_time interface directly and not
the account_xxx_ticks interface now need to do the check for the idle
process in their arch code. In particular to improve the system vs true
idle time accounting the arch code needs to measure the true idle time
instead of just testing for the idle process.
To improve the tick based accounting as well we would need an architecture
primitive that can tell us if the pt_regs of the interrupted context
points to the magic instruction that halts the cpu.
In addition idle time is no more added to the stime of the idle process.
This field now contains the system time of the idle process as it should
be. On systems without VIRT_CPU_ACCOUNTING this will always be zero as
every tick that occurs while idle is running will be accounted as idle
time.
This patch contains the necessary common code changes to be able to
distinguish idle system time and true idle time. The architectures with
support for VIRT_CPU_ACCOUNTING need some changes to exploit this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The utimescaled / stimescaled fields in the task structure and the
global cpustat should be set on all architectures. On s390 the calls
to account_user_time_scaled and account_system_time_scaled never have
been added. In addition system time that is accounted as guest time
to the user time of a process is accounted to the scaled system time
instead of the scaled user time.
To fix the bugs and to prevent future forgetfulness this patch merges
account_system_time_scaled into account_system_time and
account_user_time_scaled into account_user_time.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Michael Neuling <mikey@neuling.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
stacktrace: provide save_stack_trace_tsk() weak alias
rcu: provide RCU options on non-preempt architectures too
printk: fix discarding message when recursion_bug
futex: clean up futex_(un)lock_pi fault handling
"Tree RCU": scalable classic RCU implementation
futex: rename field in futex_q to clarify single waiter semantics
x86/swiotlb: add default swiotlb_arch_range_needs_mapping
x86/swiotlb: add default phys<->bus conversion
x86: unify pci iommu setup and allow swiotlb to compile for 32 bit
x86: add swiotlb allocation functions
swiotlb: consolidate swiotlb info message printing
swiotlb: support bouncing of HighMem pages
swiotlb: factor out copy to/from device
swiotlb: add arch hook to force mapping
swiotlb: allow architectures to override phys<->bus<->phys conversions
swiotlb: add comment where we handle the overflow of a dma mask on 32 bit
rcu: fix rcutorture behavior during reboot
resources: skip sanity check of busy resources
swiotlb: move some definitions to header
swiotlb: allow architectures to override swiotlb pool allocation
...
Fix up trivial conflicts in
arch/x86/kernel/Makefile
arch/x86/mm/init_32.c
include/linux/hardirq.h
as per Ingo's suggestions.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
