- written on init only, accessed for every timer read --> __read_mostly
- fix broken sentence
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commits
3e3318dee0 [PATCH] swsusp: x86_64 mark special saveable/unsaveable pages
b6370d96e0 [PATCH] swsusp: i386 mark special saveable/unsaveable pages
ce4ab0012b [PATCH] swsusp: add architecture special saveable pages support
because not only do they apparently cause page faults on x86, the
infrastructure doesn't compile on powerpc.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch will fix a boot memory reservation bug that trashes memory on
the ES7000 when loading the kdump crash kernel.
The code in arch/x86_64/kernel/setup.c to reserve boot memory for the crash
kernel uses the non-numa aware "reserve_bootmem" function instead of the
NUMA aware "reserve_bootmem_generic". I checked to make sure that no other
function was using "reserve_bootmem" and found none, except the ones that
had NUMA ifdef'ed out.
I have tested this patch only on an ES7000 with NUMA on and off (numa=off)
in a single (non-NUMA) and multi-cell (NUMA) configurations.
Signed-off-by: Amul Shah <amul.shah@unisys.com>
Looks-good-to: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
flush_tlb_all uses on_each_cpu, which will disable/enable interrupt.
In suspend/resume time, this will make interrupt wrongly enabled.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pages (Reserved/ACPI NVS/ACPI Data) below end_pfn will be saved/restored by S4
currently. We should mark 'Reserved' pages not saveable.
Pages (Reserved/ACPI NVS/ACPI Data) above end_pfn will not be saved/restored
by S4 currently. We should save the 'ACPI NVS/ACPI Data' pages.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_move_pages() support for 32bit (i386 plus x86_64 compat layer)
Add support for move_pages() on i386 and also add the compat functions
necessary to run 32 bit binaries on x86_64.
Add compat_sys_move_pages to the x86_64 32bit binary layer. Note that it is
not up to date so I added the missing pieces. Not sure if this is done the
right way.
[akpm@osdl.org: compile fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate the various arch-specific implementations of pxm_to_node() and
node_to_pxm() into a single generic version.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (27 commits)
[PATCH] PCI: nVidia quirk to make AER PCI-E extended capability visible
[PATCH] PCI: fix issues with extended conf space when MMCONFIG disabled because of e820
[PATCH] PCI: Bus Parity Status sysfs interface
[PATCH] PCI: fix memory leak in MMCONFIG error path
[PATCH] PCI: fix error with pci_get_device() call in the mpc85xx driver
[PATCH] PCI: MSI-K8T-Neo2-Fir: run only where needed
[PATCH] PCI: fix race with pci_walk_bus and pci_destroy_dev
[PATCH] PCI: clean up pci documentation to be more specific
[PATCH] PCI: remove unneeded msi code
[PATCH] PCI: don't move ioapics below PCI bridge
[PATCH] PCI: cleanup unused variable about msi driver
[PATCH] PCI: disable msi mode in pci_disable_device
[PATCH] PCI: Allow MSI to work on kexec kernel
[PATCH] PCI: AMD 8131 MSI quirk called too late, bus_flags not inherited ?
[PATCH] PCI: Move various PCI IDs to header file
[PATCH] PCI Bus Parity Status-broken hardware attribute, EDAC foundation
[PATCH] PCI: i386/x86_84: disable PCI resource decode on device disable
[PATCH] PCI ACPI: Rename the functions to avoid multiple instances.
[PATCH] PCI: don't enable device if already enabled
[PATCH] PCI: Add a "enable" sysfs attribute to the pci devices to allow userspace (Xorg) to enable devices without doing foul direct access
...
The AGP default doesn't work well with other selects, so use a select for
GART_IOMMU as well. Remove a redundant default for SWIOTLB as well.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 15 Jun 2006 03:45:10 +0200, Andi Kleen wrote:
> Anyways I would say that if the BIOS can't get MCFG right then
> it's likely not been validated on that board and shouldn't be used.
According to Petr Vandrovec:
... "What is important (and checked) is address of MMCONFIG reported by MCFG
table... Unfortunately code does not bother with printing that address :-(
"Another problem is that code has hardcoded that MMCONFIG area is 256MB large.
Unfortunately for the code PCI specification allows any power of two between 2MB
and 256MB if vendor knows that such amount of busses (from 2 to 128) will be
sufficient for system. With notebook it is quite possible that not full 8 bits
are implemented for MMCONFIG bus number."
So here is a patch. Unfortunately my system still fails the test because
it doesn't reserve any part of the MMCONFIG area, but this may fix others.
Booted on x86_64, only compiled on i386. x86_64 still remaps the max area
(256MB) even though only 2MB is checked... but 2.6.16 had no check at all
so it is still better.
PCI: reduce size of x86 MMCONFIG reserved area check
1. Print the address of the MMCONFIG area when the test for that area
being reserved fails.
2. Only check if the first 2MB is reserved, as that is the minimum.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: "Andy Currid" <ACurrid@nvidia.com>
This patch fixes a kernel panic during boot that occurs on NVIDIA platforms
that have HPET enabled.
When HPET is enabled, the standard timer IRQ is routed to IOAPIC pin 2 and is
advertised as such in the ACPI APIC table - but an earlier workaround in the
kernel was ignoring this override. The fix is to honor timer IRQ overrides
from ACPI when HPET is detected on an NVIDIA platform.
Signed-off-by: Andy Currid <acurrid@nvidia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.
This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Robert Hentosh <robert_hentosh@dell.com>
Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c. The following code does not handle the edge condition correctly:
while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
;
last = addr + size;
if ( last > ei->addr + ei->size )
continue;
The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:
while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
;
In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.
AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Daniel Yeisley <dan.yeisley@unisys.com>
It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells. This can create a scenario where
node 0 has cpus, but no associated memory. The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.
[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
values) on most current CPUs would overflow (observed value of the
delay was approximately 4000us, yielding an overflow for frequencies
starting a little above 1GHz)
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.
Now it uses the 8bit of randomness native i386 would use too.
This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.
Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem:
If we put a probe onto a callq instruction and the probe is executed,
kernel panic of Bad RIP value occurs.
Root cause:
If resume_execution() found 0xff at first byte of p->ainsn.insn, it must
check the _second_ byte. But current resume_execution check _first_ byte
again.
I changed it checks second byte of p->ainsn.insn.
Kprobes on i386 don't have this problem, because the implementation is a
little bit different from x86_64.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Satoshi Oshima <soshima@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extends an earlier patch from John Blackwood to more exception handlers
that also run on the exception stacks.
Expand the use of preempt_conditional_{sti,cli} to all cases where
interrupts are to be re-enabled during exception handling while running
on an IST stack.
Based on original patch from Jan Beulich.
Cc: John Blackwood <john.blackwood@ccur.com>
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some boot failures on Dell and Unisys systems with memory
hotadd added.
- Set hotadd_percent to 0 by default. This means anybody using hotadd
memory needs to specify the value on the command line. That's
because there are lots of Intel boxes which have a bogus hotplug area
in their SRAT and they would waste a lot of memory before.
- Fix calculation of how much memory to use when the hotplug area
exceeds hotadd_percent
- Fix fallback when the
- Fix fallback if memory hotadd is not compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This triggers for b44's 1GB DMA workaround which tries to map
first and then bounces.
The 32bit heuristic is reasonable because the IOMMU doesn't attempt
to handle < 32bit masks anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on analysis&patch from Robert Hentosch
Observed on a Dell PE6850 with 16GB
The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.
If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.
AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.
Cc: Robert_Hentosch@dell.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Playing with NMI watchdog on x86_64, I discovered that it didn't
do what I expected. It always panic-ed, even when it didn't
happen from interrupt context. This patch solves that
problem for me. Also, in this case, do_exit() will be called
with interrupts disabled, I believe. Would it be wise to also
call local_irq_enable() after nmi_exit()?
[Yes I added it -AK]
Currently, on x86_64, any NMI watchdog timeout will cause a panic
because the irq count will always be set to be in an interrupt
when do_exit() is called from die_nmi(). If we add nmi_exit() to
the die_nmi() call (since the nmi will never exit "normally")
it seems to solve this problem. The following small program
can be used to trigger the NMI watchdog to reproduce this:
main ()
{
iopl(3);
for (;;) asm("cli");
}
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed this when poking around in this area.
The oops_begin() function in x86_64 would only conditionally claim
the die_lock if the call is nested, but oops_end() would always
release the spinlock. This patch adds a nest count for the die lock
so that the release of the lock is only done on the final oops_end().
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IOMMU code can only deal with 8 northbridges. Error out when
more are found.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Cc: len.brown@intel.com
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Audit Filter Performance
[PATCH] Rework of IPC auditing
[PATCH] More user space subject labels
[PATCH] Reworked patch for labels on user space messages
[PATCH] change lspp ipc auditing
[PATCH] audit inode patch
[PATCH] support for context based audit filtering, part 2
[PATCH] support for context based audit filtering
[PATCH] no need to wank with task_lock() and pinning task down in audit_syscall_exit()
[PATCH] drop task argument of audit_syscall_{entry,exit}
[PATCH] drop gfp_mask in audit_log_exit()
[PATCH] move call of audit_free() into do_exit()
[PATCH] sockaddr patch
[PATCH] deal with deadlocks in audit_free()
The PC Speaker driver's ->probe() routine doesn't even get called in the
64-bit kernels. The reason for that is that the arch code apparently has
to explictly add a "pcspkr" platform device in order for the driver core to
call the ->probe() routine. arch/i386/kernel/setup.c unconditionally adds
a "pcspkr" device, but the x86_64 kernel has no code at all related to the
PC Speaker.
The patch below copies the relevant code from i386 to x86_64, which makes
the PC Speaker work for me on x86_64.
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do this by removing a micro-optimization that tries to avoid grabbing
the iommu_bitmap_lock spinlock and using a bus-locked operation.
This still races with other simultaneous alloc_iommu or free_iommu(size >
1) which both use bus-unlocked operations.
The end result of this race is eventually ending up with an
iommu_gart_bitmap that has bits errornously set all over, making large
contiguous iommu space allocations fail with 'PCI-DMA: Out of IOMMU space'.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This quietens warnings and actually fixes a bug. The unwind tables would
come out wrong without -32, causing pthread cancellation during them to
crash in the gcc runtime.
The problem seems to only happen with newer binutils (it doesn't happen
with 2.16.91.0.2 but happens wit 2.16.91.0.5)
Thanks to David Altobelli <david.altobelli@hp.com> and Brian Baker
<Brian.B@hp.com> for test case and initial analysis.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems we are trying to init the node_mem_map when we don't need to, for
example when SPARSEMEM is enabled. This causes the error below during
compilation. Use CONFIG_FLAT_NODE_MEM_MAP to gate allocation and init.
arch/x86_64/mm/numa.c: In function `setup_node_zones':
arch/x86_64/mm/numa.c:191: error: structure has no member
named `node_mem_map'
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.
This was actually documented by AMD, but nobody recognized it as
being different from Intel before.
The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.
This means other processes always will only see a constant value
defined by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs
who don't need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tee was already there for some reason for native 64bit, but
sys_sync_file_range was missing. Also add it to the compat layer.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Start booting into the capture kernel after an Oops if system is in a
unrecoverable state. System will boot into the capture kernel, if one is
pre-loaded by the user, and capture the kernel core dump.
o One of the following conditions should be true to trigger the booting of
capture kernel.
- panic_on_oops is set.
- pid of current thread is 0
- pid of current thread is 1
- Oops happened inside interrupt context.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Surprising that it still worked at all with this - yes it was
tested.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nobody should pass NULL here. Could in theory make it a BUG,
but the NULL pointer oops will do as well.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Linus it is useless now because entry.S should
handle it correctly in all cases.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bugzilla Bug 6299:
A pixel size of 8 bits produces wrong logo colors in x86_64.
The driver has 2 methods for setting the color map, using the protected
mode interface provided by the video BIOS and directly writing to the VGA
registers. The former is not supported in x86_64 and the latter is enabled
only in i386.
Fix by enabling the latter method in x86_64 only if supported by the BIOS.
If both methods are unsupported, change the visual of vesafb to
STATIC_PSEUDOCOLOR.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While cleaning up parisc_ksyms.c earlier, I noticed that strpbrk wasn't
being exported from lib/string.c. Investigating further, I noticed a
changeset that removed its export and added it to _ksyms.c on a few more
architectures. The justification was that "other arches do it."
I think this is wrong, since no architecture currently defines
__HAVE_ARCH_STRPBRK, there's no reason for any of them to be exporting it
themselves. Therefore, consolidate the export to lib/string.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
