Reset sync_search on resume. The effect is to retry syncing all out-of-sync
regions when a mirror is resumed, including ones that previously failed.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The complete_resync_work function only provides the ability to change an
out-of-sync region to in-sync. This patch enhances the function to allow us
to change the status from in-sync to out-of-sync as well, something that is
needed when a mirror write to one of the devices or an initial resync on a
given region fails.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the code that releases memory used by a snapshot into a separate function.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the pushback feature for the multipath target.
The pushback request is used when:
1) there are no valid paths;
2) queue_if_no_path was set;
3) a suspend is being issued with the DMF_NOFLUSH_SUSPENDING flag.
Otherwise bios are returned to applications with -EIO.
To check whether queue_if_no_path is specified or not, you need to check
both queue_if_no_path and saved_queue_if_no_path, because presuspend saves
the original queue_if_no_path value to saved_queue_if_no_path.
The check for 1 already exists in both map_io() and do_end_io().
So this patch adds __must_push_back() to check 2 and 3.
Test results:
See the test results in the preceding patch.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In device-mapper I/O is sometimes queued within targets for later processing.
For example the multipath target can be configured to store I/O when no paths
are available instead of returning it -EIO.
This patch allows the device-mapper core to instruct a target to transfer the
contents of any such in-target queue back into the core. This frees up the
resources used by the target so the core can replace that target with an
alternative one and then resend the I/O to it. Without this patch the only
way to change the target in such circumstances involves returning the I/O with
an error back to the filesystem/application. In the multipath case, this
patch will let us add new paths for existing I/O to try after all the existing
paths have failed.
DMF_NOFLUSH_SUSPENDING
----------------------
If the DM_NOFLUSH_FLAG ioctl option is specified at suspend time, the
DMF_NOFLUSH_SUSPENDING flag is set in md->flags during dm_suspend(). It
is always cleared before dm_suspend() returns.
The flag must be visible while the target is flushing pending I/Os so it
is set before presuspend where the flush starts and unset after the wait
for md->pending where the flush ends.
Target drivers can check this flag by calling dm_noflush_suspending().
DM_MAPIO_REQUEUE / DM_ENDIO_REQUEUE
-----------------------------------
A target's map() function can now return DM_MAPIO_REQUEUE to request the
device mapper core queue the bio.
Similarly, a target's end_io() function can return DM_ENDIO_REQUEUE to request
the same. This has been labelled 'pushback'.
The __map_bio() and clone_endio() functions in the core treat these return
values as errors and call dec_pending() to end the I/O.
dec_pending
-----------
dec_pending() saves the pushback request in struct dm_io->error. Once all
the split clones have ended, dec_pending() will put the original bio on
the md->pushback list. Note that this supercedes any I/O errors.
It is possible for the suspend with DM_NOFLUSH_FLAG to be aborted while
in progress (e.g. by user interrupt). dec_pending() checks for this and
returns -EIO if it happened.
pushdback list and pushback_lock
--------------------------------
The bio is queued on md->pushback temporarily in dec_pending(), and after
all pending I/Os return, md->pushback is merged into md->deferred in
dm_suspend() for re-issuing at resume time.
md->pushback_lock protects md->pushback.
The lock should be held with irq disabled because dec_pending() can be
called from interrupt context.
Queueing bios to md->pushback in dec_pending() must be done atomically
with the check for DMF_NOFLUSH_SUSPENDING flag. So md->pushback_lock is
held when checking the flag. Otherwise dec_pending() may queue a bio to
md->pushback after the interrupted dm_suspend() flushes md->pushback.
Then the bio would be left in md->pushback.
Flag setting in dm_suspend() can be done without md->pushback_lock because
the flag is checked only after presuspend and the set value is already
made visible via the target's presuspend function.
The flag can be checked without md->pushback_lock (e.g. the first part of
the dec_pending() or target drivers), because the flag is checked again
with md->pushback_lock held when the bio is really queued to md->pushback
as described above. So even if the flag is cleared after the lockless
checkings, the bio isn't left in md->pushback but returned to applications
with -EIO.
Other notes on the current patch
--------------------------------
- md->pushback is added to the struct mapped_device instead of using
md->deferred directly because md->io_lock which protects md->deferred is
rw_semaphore and can't be used in interrupt context like dec_pending(),
and md->io_lock protects the DMF_BLOCK_IO flag of md->flags too.
- Don't issue lock_fs() in dm_suspend() if the DM_NOFLUSH_FLAG
ioctl option is specified, because I/Os generated by lock_fs() would be
pushed back and never return if there were no valid devices.
- If an error occurs in dm_suspend() after the DMF_NOFLUSH_SUSPENDING
flag is set, md->pushback must be flushed because I/Os may be queued to
the list already. (flush_and_out label in dm_suspend())
Test results
------------
I have tested using multipath target with the next patch.
The following tests are for regression/compatibility:
- I/Os succeed when valid paths exist;
- I/Os fail when there are no valid paths and queue_if_no_path is not
set;
- I/Os are queued in the multipath target when there are no valid paths and
queue_if_no_path is set;
- The queued I/Os above fail when suspend is issued without the
DM_NOFLUSH_FLAG ioctl option. I/Os spanning 2 multipath targets also
fail.
The following tests are for the normal code path of new pushback feature:
- Queued I/Os in the multipath target are flushed from the target
but don't return when suspend is issued with the DM_NOFLUSH_FLAG
ioctl option;
- The I/Os above are queued in the multipath target again when
resume is issued without path recovery;
- The I/Os above succeed when resume is issued after path recovery
or table load;
- Queued I/Os in the multipath target succeed when resume is issued
with the DM_NOFLUSH_FLAG ioctl option after table load. I/Os
spanning 2 multipath targets also succeed.
The following tests are for the error paths of the new pushback feature:
- When the bdget_disk() fails in dm_suspend(), the
DMF_NOFLUSH_SUSPENDING flag is cleared and I/Os already queued to the
pushback list are flushed properly.
- When suspend with the DM_NOFLUSH_FLAG ioctl option is interrupted,
o I/Os which had already been queued to the pushback list
at the time don't return, and are re-issued at resume time;
o I/Os which hadn't been returned at the time return with EIO.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a dm ioctl option to request noflush suspending. (See next patch for
what this is for.) As the interface is extended, the version number is
incremented.
Other than accepting the new option through the interface, There is no change
to existing behaviour.
Test results:
Confirmed the option is given from user-space correctly.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update existing targets to use the new symbols for return values from target
map and end_io functions.
There is no effect on behaviour.
Test results:
Done build test without errors.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tighten the use of return values from the target map and end_io functions.
Values of 2 and above are now explictly reserved for future use. There are no
existing targets using such values.
The patch has no effect on existing behaviour.
o Reserve return values of 2 and above from target map functions.
Any positive value currently indicates "mapping complete", but all
existing drivers use the value 1. We now make that a requirement
so we can assign new meaning to higher values in future.
The new definition of return values from target map functions is:
< 0 : error
= 0 : The target will handle the io (DM_MAPIO_SUBMITTED).
= 1 : Mapping completed (DM_MAPIO_REMAPPED).
> 1 : Reserved (undefined). Previously this was the same as '= 1'.
o Reserve return values of 2 and above from target end_io functions
for similar reasons.
DM_ENDIO_INCOMPLETE is introduced for a return value of 1.
Test results:
I have tested by using the multipath target.
I/Os succeed when valid paths exist.
I/Os are queued in the multipath target when there are no valid paths and
queue_if_no_path is set.
I/Os fail when there are no valid paths and queue_if_no_path is not set.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the interface of dm_suspend() so that we can pass several options
without increasing the number of parameters. The existing 'do_lockfs' integer
parameter is replaced by a flag DM_SUSPEND_LOCKFS_FLAG.
There is no functional change to the code.
Test results:
I have tested 'dmsetup suspend' command with/without the '--nolockfs'
option and confirmed the do_lockfs value is correctly set.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The existing code allocates an extra slot in bi_io_vec[] and uses it to store
the region number.
This patch hides the extra slot from bio_add_page() so the region number can't
get overwritten.
Also remove a hard-coded SECTOR_SHIFT and fix a typo in a comment.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename DM's struct path to struct dm_path to prevent name collision between it
and struct path from fs/namei.c.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <reiserfs-dev@namesys.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md_open takes ->reconfig_mutex which causes lockdep to complain. This
(normally) doesn't have deadlock potential as the possible conflict is with a
reconfig_mutex in a different device.
I say "normally" because if a loop were created in the array->member hierarchy
a deadlock could happen. However that causes bigger problems than a deadlock
and should be fixed independently.
So we flag the lock in md_open as a nested lock. This requires defining
mutex_lock_interruptible_nested.
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the old complex and crufty bd_mutex annotation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than stuffing integers into pointers with casts, let's use
a union.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRW-32-AES needs a certain IV. This IV should be provided dm-crypt.
The block cipher mode could, in principle generate the correct IV from
the plain IV, but I think that it is cleaner to supply the right IV
directly.
The sector -> narrow block calculation uses a shift for performance reasons.
This shift is computed in .ctr and stored in cc->iv_gen_private (as a void *).
Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If there's a swap file on a software RAID, it should be possible to use this
file for saving the swsusp's suspend image. Also, this file should be
available to the memory management subsystem when memory is being freed before
the suspend image is created.
For the above reasons it seems that md_threads should not be frozen during the
suspend and the appended patch makes this happen, but then there is the
question if they don't cause any data to be written to disks after the suspend
image has been created, provided that all filesystems are frozen at that time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that CHANGE is preferred to ONLINE/OFFLINE for various reasons
(not least of which being that udev understands it already).
So remove the recently added KOBJ_OFFLINE (no-one is likely to care anyway)
and change the ONLINE to a CHANGE event
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All device-mapper targets must complete outstanding I/O before suspending.
The mirror target generates I/O in its recovery phase and fails to wait for
it. It needs to be tracked so we can ensure that it has completed before we
suspend.
[akpm@osdl.org: cleanup]
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When adding paths to the round-robin path selector, their order gets inverted,
which is not desirable.
Fix by replacing list_add() with list_add_tail().
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the device is already suspended, just return the error and skip the code
that would incorrectly wipe md->suspended_bdev.
(This isn't currently a problem because existing code avoids calling this
function if the device is already suspended.)
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a race between dev_create() and find_device().
If the mdptr has not yet been stored against a device, find_device() needs to
behave as though no device was found. It already returns NULL, but there is a
dm_put() missing: it must drop the reference dm_get_md() took.
The bug was introduced by dm-fix-mapped-device-ref-counting.patch.
It manifests itself if another dm ioctl attempts to reference a newly-created
device while the device creation ioctl is still running. The consequence is
that the device cannot be removed until the machine is rebooted. Certain udev
configurations can lead to this happening.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows udev to do something intelligent when an array becomes
available.
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix dm-crypt after the block cipher API changes to correctly return the
backwards compatible cipher-chainmode[-ivmode] format for "dmsetup
table".
Signed-off-by: Christophe Saout <christophe@saout.de>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
diff linux-2.6.19-rc3.orig/drivers/md/dm-crypt.c linux-2.6.19-rc3/drivers/md/dm-crypt.c
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent fix which made sure ->degraded was initialised properly exposed a
second bug - ->degraded wasn't been updated when drives failed or were
hot-added.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow --size=xxx" is used to resize an array (use more or less of
each device), we check the new siza against the available space in each
device.
We already have that number recorded in rdev->size, so calculating it is
pointless (and wrong in one obscure case).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If save_raid_disk is >= 0, then the device could be a device that is already
in sync that is being re-added. So we need to default this value to -1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
And a couple of bug fixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Includes a couple of bugfixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two less-used md personalities have bugs in the calculation of ->degraded (the
extent to which the array is degraded).
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the concept of "queue congestion" from "backing-dev congestion".
Congestion is a backing-dev concept, not a queue concept.
The blk_* congestion functions are retained, as wrappers around the core
backing-dev congestion functions.
This proper layering is needed so that NFS can cleanly use the congestion
functions, and so that CONFIG_BLOCK=n actually links.
Cc: "Thomas Maier" <balagi@justmail.de>
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have seen mdadm oops after successfully unloading md module.
This patch privents from unloading md module while
mdadm is polling /proc/mdstat.
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a bug introduced in 2.6.18.
If a drive is added to a raid1 using older tools (mdadm-1.x or raidtools)
then it will be included in the array without any resync happening.
It has been submitted for 2.6.18.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
find_first_set doesn't find the least-significant bit on bigendian machines,
so it is really wrong to use it.
ffs is closer, but takes an 'int' and we have a 'unsigned long'. So use
ffz(~X) to convert a chunksize into a chunkshift.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have had enough success reports not to believe that this is safe for 2.6.19.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Once upon a time we needed to fixed limit to the number of md devices,
probably because we preallocated some array. This need no longer exists, but
we still have an arbitrary limit.
So remove MAX_MD_DEVS and allow as many devices as we can fit into the 'minor'
part of a device number.
Also remove some useless noise at init time (which reports MAX_MD_DEVS) and
remove MD_THREAD_NAME_MAX which hasn't been used for a while.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is possible to request a 'check' of an md/raid array where the whole array
is read and consistancies are reported.
This uses the same mechanisms as 'resync' and so reports in the kernel logs
that a resync is being started. This understandably confuses/worries people.
Also the text in /proc/mdstat suggests a 'resync' is happen when it is just a
check.
This patch changes those messages to be more specific about what is happening.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is very different from other raid levels and all requests go through a
'stripe cache', and it has congestion management already.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
raid1, raid10 and multipath don't report their 'congested' status through
bdi_*_congested, but should.
This patch adds the appropriate functions which just check the 'congested'
status of all active members (with appropriate locking).
raid1 read_balance should be modified to prefer devices where
bdi_read_congested returns false. Then we could use the '&' branch rather
than the '|' branch. However that should would need some benchmarking first
to make sure it is actually a good idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Each backing_dev needs to be able to report whether it is congested, either by
modulating BDI_*_congested in ->state, or by defining a ->congested_fn.
md/raid did neither of these. This patch add a congested_fn which simply
checks all component devices to see if they are congested.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.
So:
- use test-and-set and test-and-clear to synchonise
the In_sync bits with the ->degraded count
- use the spinlock to protect updates to the
degraded count (could use an atomic_t but that
would be a bigger change in code, and isn't
really justified)
- remove un-necessary locking in raid5
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is equivalent to conf->raid_disks - conf->mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
raid1d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new sysfs interface that allows the bitmap of an array to be dirtied.
The interface is write-only, and is used as follows:
echo "1000" > /sys/block/md2/md/bitmap
(dirty the bit for chunk 1000 [offset 0] in the in-memory and on-disk
bitmaps of array md2)
echo "1000-2000" > /sys/block/md1/md/bitmap
(dirty the bits for chunks 1000-2000 in md1's bitmap)
This is useful, for example, in cluster environments where you may need to
combine two disjoint bitmaps into one (following a server failure, after a
secondary server has taken over the array). By combining the bitmaps on
the two servers, a full resync can be avoided (This was discussed on the
list back on March 18, 2005, "[PATCH 1/2] md bitmap bug fixes" thread).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It isn't needed as mddev->degraded contains equivalent info.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They are not needed. conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
raid10d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the scheduled removal of the START_ARRAY ioctl for md.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for a per-target dm_flush_fn method. This is needed
to allow dm-loop to invalidate page cache mappings in response to BLKFLSBUF
ioctl commands.
Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate the setting of device I/O limits from dm_get_device(). dm-loop will
use this.
Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found a problem within device-mapper that occurs in low-mem situations. It
was found using a mirror target but I think in theory it would hit any setup
that stacks device-mapper devices (like LVM on top of multipath).
Since device-mapper core uses the common fs_bioset in clone_bio(), and a
private, but still global, bio_set in split_bvec() it is possible that the
filesystem and the first level target successfully get bios but the lower
level target doesn't because there is no more memory and the pool was drained
by upper layers. So the remapping will be stuck forever. To solve this
device-mapper core needs to use a private bio_set for each device.
Signed-off-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the low memory situation dm-crypt needs to use a private mempool of bios to
avoid blocking.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is designed to help dm-crypt comply with the
new constraints imposed by the following patch in -mm:
md-dm-reduce-stack-usage-with-stacked-block-devices.patch
Under low memory the existing implementation relies upon waiting for I/O
submitted recursively to generic_make_request() completing before the original
generic_make_request() call can return.
This patch moves the I/O submission to a workqueue so the original
generic_make_request() can return immediately.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restructure the dm-crypt write processing in preparation for workqueue changes
in the next patches.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restructure part of the dm-crypt code in preparation for workqueue changes.
Use 'base_bio' or 'clone' variable names consistently throughout. No
functional changes are included in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the facility to wipe the encryption key from memory (for example while a
laptop is suspended) and reinstate it later (when the laptop gets resumed).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a target preresume hook.
It is called before the targets are resumed and if it returns an error the
resume gets cancelled.
The crypt target will use this to indicate that it is unable to process I/O
because no encryption key has been supplied.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Device-mapper devices are not accessible until a 'resume' ioctl has been
issued. For userspace to find out when this happens we need to generate an
uevent for udev to take appropriate action.
As discussed at OLS we should send 'change' events for 'resume'. We can think
of no useful purpose served by also having 'suspend' events.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After initialising m->ti, there's no need to pass it in subsequent calls to
static functions used for parsing parameters.
Signed-off-by: Micha³ Miros³aw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove trailing space from 'dmsetup table' output.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a snapshot became invalid while there are outstanding pending_exceptions,
when pending_complete() processes each one it forgets to remove the
corresponding exception from its exception table before freeing it.
Fix this by moving the 'out:' label up one statement so that
remove_exception() is always called. Then __invalidate_exception() no longer
needs to call it and its 'pe' argument become superfluous.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename sibling_count to ref_count and introduce get and put functions.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a workqueue so that I/O can be queued up to be flushed from a separate
thread (e.g. if local interrupts are disabled).
A new per-snapshot spinlock pe_lock is introduced to protect queued_bios.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rearranges the pending_complete() code so that the functional
changes in subsequent patches are clearer.
By consolidating the error and the non-error paths, we can move
error_snapshot_bios() and __flush_bios() in line.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rearranges the snapshot_map code so that the functional changes in
subsequent patches are clearer.
The only functional change is to replace the existing read lock with a write
lock which the next patch needs.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When suspending a device-mapper device, dm_suspend() sleeps until all
necessary I/O is completed. This state is triggered by a callback from
persistent_commit(). But some I/O can still be issued *after* the callback
(to prepare the next metadata area for use if the current one is full). This
patch delays the callback until after that I/O is complete.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
read_exception() and write_exception() only return an error if supplied with
an out-of-range index. If this ever happens it's the result of a bug in the
calling code so we handle this with an assertion and remove the error handling
in the callers.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the error handling when store.read_metadata is called: the error should be
returned immediately.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The chunk size of snapshots cannot be changed so it is redundant to require it
as a parameter when activating an existing snapshot. Allow a value of zero in
this case and ignore it. For a new snapshot, use a default value if zero is
specified.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While reading the code I found a bug in the error path in alloc_dev in dm.c
When blk_alloc_queue fails there is no call to free_minor.
This patch fixes the problem.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new ioctl code passes the wrong file pointer to the underlying device.
No file pointer is available so make a temporary fake one.
ioctl_by_bdev() does set_fs(KERNEL_DS) so it's for ioctls originating
within the kernel and unsuitable here. We are processing ioctls that
originated in userspace and mapping them to different devices. Fixing the
existing callers that pass a NULL file struct and consolidating the
fake_file users are separate matters to solve in later patches.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export blkdev_driver_ioctl for device-mapper.
If we get as far as the device-mapper ioctl handler, we know the ioctl is not
a standard block layer BLK* one, so we don't need to check for them a second
time and can call blkdev_driver_ioctl() directly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an ioctl is performed on a multipath device simply pass it on to the
underlying block device through current_path. If current path is not yet
selected, select it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an ioctl is performed on a device with a linear target, simply pass it on
to the underlying block device.
Note that the ioctl will pass through the filtering in blkdev_ioctl() twice.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the core device-mapper infrastructure to accept arbitrary ioctls on a
mapped device provided that it has exactly one target and it is capable of
supporting ioctls.
[We can't use unlocked_ioctl because we need 'inode': 'file' might be NULL.
Is it worth changing this?]
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Arnd Bergmann <arnd@arndb.de> wrote:
> Am Wednesday 21 June 2006 21:31 schrieb Alasdair G Kergon:
> > static struct block_device_operations dm_blk_dops = {
> > .open = dm_blk_open,
> > .release = dm_blk_close,
> > +.ioctl = dm_blk_ioctl,
> > .getgeo = dm_blk_getgeo,
> > .owner = THIS_MODULE
>
> I guess this also needs a ->compat_ioctl method, otherwise it won't
> work for ioctl numbers that have a compat_ioctl implementation in the
> low-level device driver.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Just some minor comment nits.
- little-endian is better than low-endian
- and since it is called essiv everywere it should also be essiv
in the comments (and not ess_iv)
Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts dm-crypt to use the new block cipher type where
applicable. It also changes simple cipher operations to use the new
encrypt_one/decrypt_one interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need to be careful when referencing mirrors[i].rdev. It can disappear
under us at various times.
So:
fix a couple of problem places.
comment a couple of non-problem places
move an 'atomic_add' which deferences rdev down a little
way to some where where it is sure to not be NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch broke the ability to do a user-request check of a raid1.
This patch fixes the breakage and also moves a comment that was dislocated
by the same patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we
- shut down a clean array,
- restart with one (or more) drive(s) missing
- make some changes
- pause, so that they array gets marked 'clean',
the event count on the superblock of included drives
will be the same as that of the removed drives.
So adding the removed drive back in will cause it
to be included with no resync.
To avoid this, we only update the eventcount backwards when the array
is not degraded. In this case there can (should) be no non-connected
drives that we can get confused with, and this is the particular case
where updating-backwards is valuable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On an nForce4-equipped machine with two SATA disk in raid1 setup using dmraid,
we experienced frequent deadlock of the system under high i/o load. 'cat
/dev/zero > ~/zero' was the most reliable way to reproduce them: Randomly
after a few GB, 'cp' would be left in 'D' state along with kjournald and
kmirrord. The functions cp and kjournald were blocked in did vary, but
kmirrord's wchan always pointed to 'mempool_alloc()'. We've seen this pattern
on 2.6.15 and 2.6.17 kernels. http://lkml.org/lkml/2005/4/20/142 indicates
that this problem has been around even before.
So much for the facts, here's my interpretation: mempool_alloc() first tries
to atomically allocate the requested memory, or falls back to hand out
preallocated chunks from the mempool. If both fail, it puts the calling
process (kmirrord in this case) on a private waitqueue until somebody refills
the pool. Where the only 'somebody' is kmirrord itself, so we have a
deadlock.
I worked around this problem by falling back to a (blocking) kmalloc when
before kmirrord would have ended up on the waitqueue. This defeats part of
the benefits of using the mempool, but at least keeps the system running. And
it could be done with a two-line change. Note that mempool_alloc() clears the
GFP_NOIO flag internally, and only uses it to decide whether to wait or return
an error if immediate allocation fails, so the attached patch doesn't change
behaviour in the non-deadlocking case. Path is against current git
(2.6.18-rc4), but should apply to earlier versions as well. I've tested on
2.6.15, where this patch makes the difference between random lockup and a
stable system.
Signed-off-by: Daniel Kobras <kobras@linux.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch that allowed linear arrays to be reconfigured on-line
allowed in a bug which results in divide by zero - not all
mddev->array_size were converted to conf->array_size.
This patch finished the conversion and fixed the bug.
The offending patch was commit 7c7546ccf6.
Thanks to Simon Kirby <sim@netnation.com> for the bug report.
Cc: Simon Kirby <sim@netnation.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers. Fix.
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places we use number (0660) someplaces names (S_IRUGO). Change all
numbers to be names, and change 0655 to be what it should be.
Also make some formatting more consistent.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has to be done in ->load_super, not ->validate_super
Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator.
Effects on non-lockdep kernels:
- the introduction of the following function variants:
extern struct block_device *open_partition_by_devnum(dev_t, unsigned);
extern int blkdev_put_partition(struct block_device *);
static int
blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags);
which on non-lockdep are the same as open_by_devnum(), blkdev_put()
and blkdev_get().
- a subclass parameter to do_open(). [unused on non-lockdep]
- a subclass parameter to __blkdev_put(), which is a new internal
function for the main blkdev_put*() functions. [parameter unused
on non-lockdep kernels, except for two sanity check WARN_ON()s]
these functions carry no semantical difference - they only express
object dependencies towards the lockdep subsystem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RAID5 recently changed to RAID456
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus... (and fly spell found more).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size calculation made assumtion which the new offset mode didn't
follow. This gets the size right in all cases.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix problems with new bmap based access to bitmap files.
1/ When not using a file based bitmap, attach a NULL list of buffers
to each page so the common free_buffer routine can cope.
2/ Use submit_bh to read as well as write, rather than vfs_read.
This makes read and write more symetric.
3/ sync the file before reading, to ensure that the page cache has no
dirty pages that might get written out later.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out. I don't believe this is a supportable
approach.
This patch changes the approach to use the same approach as swap files. i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.
swapfile only uses parts of the file that provide a full pages at contiguous
addresses. We don't have that luxury so we have to cope with pages that are
non-contiguous in storage. To handle this we attach buffers to each page, and
store the addresses in those buffers.
With this approach the pagecache may contain data which is inconsistent with
what is on disk. To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file. If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used. And new version of mdadm will have support for this.
This approach simplifies a lot of code:
- we no longer need to keep a list of pages which we need to wait for,
as the b_endio function can keep track of how many outstanding
writes there are. This saves a mempool.
- -EAGAIN returns from write_page are no longer possible (not sure if
they ever were actually).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it. The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.
This patch tidies that up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_active is never called, and the BITMAP_ACTIVE flag is never users or
tested, so discard them both.
Also remove some out-of-date 'todo' comments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap gets a collection of pages representing the bitmap when it
initialises the bitmap, and puts all the references when discarding the
bitmap.
It also occasionally takes extra references without any good reason, and
sometimes drops them ... though it doesn't always drop them, which can result
in a memory leak.
This patch removes the unnecessary 'get_page' calls, and the corresponding
'put_page' calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular, this means that we use 4 bits per page instead of a whole
unsigned long.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap has some attributes per-page. Handling of these attributes in
largely abstracted in set_page_attr and clear_page_attr. However
get_page_attr exposes the format used to store them. So prior to changing
that format, introduce test_page_attr instead of get_page_attr, and make
appropriate usage changes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).
However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work. The same result can be
achieved by doing the waiting directly in bitmap_unplug.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).
The file also wasn't closed if adding the bitmap file failed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as raid5 sync_request is WAY too big.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes. e.g.
A B C D
D A B C
E F G H
H E F G
(columns are drives, rows are stripes, LETTERS are chunks of data).
This is similar to raid10's 'far' mode, but not quite the same. So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.
So remove the message for non-active arrays.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
This delay turns out to be too short for some real workloads. So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning was slightly useful back in 2.2 days, but is more an annoyance
now. It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change made this goto unnecessary, so reformat the code to make it
clearer what is happening.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy device-mapper error messages to include context information
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you misuse the device-mapper interface (or there's a bug in your userspace
tools) it's possible to end up with 'unlinked' mapped devices that cannot be
removed until you reboot (along with uninterruptible processes).
This patch prevents you from removing a device that is still open.
It introduces dm_lock_for_deletion() which is called when a device is about to
be removed to ensure that nothing has it open and nothing further can open it.
It uses a private open_count for this which also lets us remove one of the
problematic bdget_disk() calls elsewhere.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a library function dm_create_error_table() to create a table that rejects
any I/O sent to a device with EIO.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move definitions of core device-mapper functions for manipulating mapped
devices and their tables to <linux/device-mapper.h> advertising their
availability for use elsewhere in the kernel.
Protect the contents of device-mapper.h with ifdef __KERNEL__. And throw
in a few formatting clean-ups and extra comments.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge dm_create() and dm_create_with_minor() by introducing the special value
DM_ANY_MINOR to request the allocation of the next available minor number.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return sense if dm_split_args is called with a NULL input parameter.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kcopyd should accumulate errors - otherwise I/O failures may be ignored
unintentionally.
And invert 'success' (used in a future patch), using a more intuitive
!(read_err || write_err).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a mirror is reduced in size, clear the part of the bitmap that is no
longer used.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the 'sizeof' in the region log bitmap size calculation: it's uint32_t, not
unsigned long - this breaks on some archs.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refactor the code that creates the core and disk log contexts to avoid the
repeated allocation of clean_bits introduced by the last patch.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On-disk logs for dm-mirror devices are currently hard-coded to use 512 byte
hard-sector-sizes. This patch fixes dm-log so it will work with devices with
non-512-byte hard-sector-sizes.
To maintain full compatibility, instead of moving the clean-bits bitset to a
bitset, and enlarges the disk-header buffer to encompass both the header and
the bitset. The I/O routines for the bitset are removed, and the I/O routines
for the disk-header now also read/write the bitset.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The table is indexed from 0, so an index equal to t->num_targets should be
rejected.
(There is no code in the current tree that would exercise this bug.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The device-mapper core does not perform any remapping of bios before passing
them to the targets. If a particular mapping begins part-way into a device,
targets obtain the sector relative to the start of the mapping by subtracting
ti->begin.
The dm-raid1 target didn't do this everywhere: this patch fixes it, taking
care to subtract ti->begin exactly once for each bio.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In alloc_dev(), we register the device with the block layer and then continue
to initialize the device. But register_disk() makes the device available to
be opened before we have completed initialising it.
This patch moves the final bits of the initialization above the disk
registration.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reference counting on dm-mod is zero if no mapped devices are open. This
is incorrect, and can lead to an oops if the module is unloaded while mapped
devices exist.
This patch claims a reference to the module whenever a device is created, and
drops it again when the device is freed.
Devices must be removed before dm-mod is unloaded.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid races, _minor_lock must be held while changing mapped device
reference counts.
There are a few paths where a mapped_device pointer is returned before a
reference is taken. This patch fixes them.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a chicken and egg problem between the block layer and dm in which the
gendisk associated with a mapping keeps a reference-less pointer to the
mapped_device.
This patch uses a new flag DMF_FREEING to indicate when the mapped_device is
no longer valid. This is checked to prevent any attempt to open the device
from succeeding while the device is being destroyed.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While removing a device, another another thread might attempt to resurrect it.
This patch replaces the _minor_lock mutex with a spinlock and uses
atomic_dec_and_lock() to serialize reference counting in dm_put().
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
idr_pre_get() can sleep while allocating memory.
The next patch will change _minor_lock into a spinlock, so this patch moves
idr_pre_get() outside the lock in preparation.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One part of the system can attempt to use a mapped device before another has
finished initialising it or while it is being freed.
This patch introduces a place holder value, MINOR_ALLOCED, to mark the minor
as allocated but in a state where it can't be used, such as mid-allocation or
mid-free. At the end of the initialization, it replaces the place holder with
the pointer to the mapped_device, making it available to the rest of the dm
subsystem.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Persistent snapshots currently store a private copy of the chunk size.
Userspace also supplies the chunk size when loading a snapshot. Ensure
consistency by only storing the chunk_size in one place instead of two.
Currently the two sizes will differ if the chunk size supplied by userspace
does not match the chunk size an existing snapshot actually uses. Amongst
other problems, this causes an incorrect 'percentage full' to be reported.
The patch ensures consistency by only storing the chunk_size in one place,
removing it from struct pstore. Some initialisation is delayed until the
correct chunk_size is known. If read_header() discovers that the wrong chunk
size was supplied, the 'area' buffer (which the header already got read into)
is reinitialised to the correct size.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a NULL dereference spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
otherwise we get nasty messages about locks not being released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This loop that sets up the hash_table has problems.
Careful examination will show that the last time through, everything but
the first line is pointless. This is because all it does is change 'cur'
and 'size' and neither of these are used after the loop. This should ring
warning bells... That last time through the loop,
size += conf->strip_zone[cur].size
can index off the end of the strip_zone array. Depending on what it finds
there, it might exit the loop cleanly, or it might spin going further and
further beyond the array until it hits an unmapped address.
This patch rearranges the code so that the last, pointless, iteration of
the loop never happens. i.e. the one statement of the last loop that is
needed is moved the the end of the previous loop - or to before the loop
starts - and the loop counter starts from 1 instead of 0.
Cc: "Don Dupuis" <dondster@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
reshape_position is a 64bit field that was not 64bit aligned. So swap with
new_level.
NOTE: this is a user-visible change. However:
- The bad code has not appeared in a released kernel
- This code is still marked 'experimental'
- This only affects version-1 superblock, which are not in wide use
- These field are only used (rather than simply reported) by user-space
tools in extemely rare circumstances : after a reshape crashes in the
first second of the reshape process.
So I believe that, at this stage, the change is safe. Especially if people
heed the 'help' message on use mdadm-2.4.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors. However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
