As part of adding hugetlbfs support for MIPS, I am adding a new
kconfig variable 'SYS_SUPPORTS_HUGETLBFS'. Since some mips cpu
varients don't yet support it, we can enable selection of HUGETLBFS on
a system by system basis from the arch/mips/Kconfig.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: William Irwin <wli@holomorphy.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TLB handlers need to check for huge pages and give them special
handling. Huge pages consist of two contiguous sub-pages of physical
memory.
* Loading entrylo0 and entrylo1 need to be handled specially.
* The page mask must be set for huge pages and then restored after
writing the TLB entries.
* The PTE for huge pages resides in the PMD, we halt traversal of the
tables there.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The octeon-ethernet driver supports the sgmii, rgmii, spi, and xaui
ports present on the Cavium OCTEON family of SOCs. These SOCs are
multi-core mips64 processors with existing support over in arch/mips.
The driver files can be categorized into three basic groups:
1) Register definitions, these are named cvmx-*-defs.h
2) Main driver code, these have names that don't start cvmx-.
3) Interface specific functions and other utility code, names starting
with cvmx-
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The octeon-ethernet driver needs to check for additional chip specific
features, we add them to the octeon_has_feature() framework.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The bootloader now uses additional board type constants. The
octeon-ethernet driver needs some of the new values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various Octeon ethernet drivers use these new functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few open-coded GPIO register accesses with gpio calls.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls to
the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gpio_direction_output should also set an output value according to the API.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Rewrite to use <asm-generic/ioctl.h>. Cuts down the file from 40 to
16 lines.
o Delete _IOC_VOID, _IOC_OUT, _IOC_IN and _IOC_INOUT. They were added
for 2.1.14 but I was not able to find any user - not even historical
ones.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated RNG of the TX4939 SoC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev to access SRAM in TXx9 SoCs via sysfs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: Make driver depend on MACH_U300
i2c-s3c2410: use resource_size()
i2c: Use resource_size macro
i2c: ST DDC I2C U300 bus driver v3
i2c-bfin-twi: pull in io.h for ioremap()
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
Authentication error abort codes should be translated to appropriate
Linux error codes, rather than all being translated to EREMOTEIO - which
indicates that the server had internal problems.
Additionally, a server shouldn't be marked unavailable and the next
server tried if an authentication error occurs. This will quickly make
all the servers unavailable to the client. Instead the error should be
returned straight to the user.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Connections that have seen a connection-level abort should not be reused
as the far end will just abort them again; instead a new connection
should be made.
Connection-level aborts occur due to such things as authentication
failures.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some architectures need to initialize SLAB caches to be able
to allocate page tables. They do that from pgtable_cache_init()
so the later should be called earlier now, best is before
vmalloc_init().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
