Return the number of bytes buffered in rxrpc_send_data().
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_vs currently fails to reset its ip_vs_sync_state variable if the
sync thread fails to start properly. The result is that the kernel
will report a running daemon when their actuall is none.
If you issue the following commands:
1. ipvsadm --start-daemon master --mcast-interface bla
2. ipvsadm -L --daemon
3. ipvsadm --stop-daemon master
Assuming that bla is not an actual interface, step 2 should return no
data, but instead returns:
$ ipvsadm -L --daemon
master sync daemon (mcast=bla, syncid=0)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My IPsec MTU optimization patch introduced a regression in MTU calculation
for non-ESP SAs, the SA's header_len needs to be subtracted from the MTU if
the transform doesn't provide a ->get_mtu() function.
Reported-and-tested-by: Marco Berizzi <pupilla@hotmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a NULL dereference spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6f74651ae6 is found guilty
of breaking DSACK counting, which should be done only for the
SACK block reported by the DSACK instead of every SACK block
that is received along with DSACK information.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 164891aadf broke RTT
sampling of congestion control modules. Inaccurate timestamps
could be fed to them without providing any way for them to
identify such cases. Previously RTT sampler was called only if
FLAG_RETRANS_DATA_ACKED was not set filtering inaccurate
timestamps nicely. In addition, the new behavior could give an
invalid timestamp (zero) to RTT sampler if only skbs with
TCPCB_RETRANS were ACKed. This solves both problems.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that added ipv6_hwtype is broken on tuntap tunnels.
Indeed, it's broken on any device that does not pass the ipv6_hwtype
test.
The reason is that the original test only applies to autoconfiguration,
not IPv6 support. IPv6 support is allowed on any device. In fact,
even with the ipv6_hwtype patch applied you can still add IPv6 addresses
to any interface that doesn't pass thw ipv6_hwtype test provided that
they have a sufficiently large MTU. This is a serious problem because
come deregistration time these devices won't be cleaned up properly.
I've gone back and looked at the rationale for the patch. It appears
that the real problem is that we were creating IPv6 devices even if the
MTU was too small. So here's a patch which fixes that and reverts the
ipv6_hwtype stuff.
Thanks to Kanru Chen for reporting this issue.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flaw does not affect any behavior (currently).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, when we receive a mtu estimate smaller then minim
threshold in the ICMP message, we disable the path mtu discovery
on the transport. This leads to the never increasing sctp fragmentation
point even when the real path mtu has increased.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currently, if the socket is owned by the user, we drop the ICMP
message. As a result SCTP forgets that path MTU changed and
never adjusting it's estimate. This causes all subsequent
packets to be fragmented. With this patch, we'll flag the association
that it needs to udpate it's estimate based on the already updated
routing information.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Introduce new function sctp_transport_update_pmtu that updates
the transports and destination caches view of the path mtu.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
If the copy_to_user or copy_user calls fail in sctp_getsockopt_local_addrs(),
the function should free locally allocated storage before returning error.
Spotted by Coverity.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Allow sctp_bindx() to accept multiple address with
unspecified port. In this case, all addresses inherit
the first bound port. We still catch full mis-matches.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
During peeloff of AF_INET6 socket, the inet6_sk(sk)->daddr
wasn't set correctly since the code was assuming IPv4 only.
Now we use a correct call to set the destination address.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Because of the current default of 100, Cubic and BIC perform very
poorly compared to standard Reno.
In the worst case, this change makes Cubic and BIC as aggressive as
Reno. So this change should be very safe.
Signed-off-by: David S. Miller <davem@davemloft.net>
Without FRTO, the tcp_try_to_open is never called with
lost_out > 0 (see tcp_time_to_recover). However, when FRTO is
enabled, the !tp->lost condition is not used until end of FRTO
because that way TCP avoids premature entry to fast recovery
during FRTO.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 stops the tx queues during scans. This is wrong with respect
to the master deivce tx queue, since stopping it prevents any probes
from being sent during the scan. Instead, they accumulate in the queue
and are only sent after the scan is finished, which is obviously
wrong.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a typo in mac80211's debugfs.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix signedness mixup making mac addresses show up strangely
(like 00:11:22:33:44:ffffffaa) in /sys/class/ieee80211/*/macaddress.
Signed-off-by: David Lamparter <equinox@diac24.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jean II was right: you have to re-charge the final timer when
resending rejected frames. Otherwise it triggers at a wrong time and
can break the currently running communication. Reproducible under
rt-preempt.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: G. Liakhovetski <gl@dsa-ac.de>
We need to switch to NRM _before_ sending the final packet otherwise
we might hit a race condition where we get the first packet from the
peer while we're still in LAP_XMIT_P.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 options are not very well aligned within the packet and the
format of a CIPSO option is even worse. The result is that the CIPSO
engine in the kernel does a few unaligned accesses when parsing and
validating incoming packets with CIPSO options attached which generate
error messages on certain alignment sensitive platforms. This patch
fixes this by marking these unaligned accesses with the
get_unaliagned() macro.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current NetLabel code has some redundant APIs which allow both
"struct socket" and "struct sock" types to be used; this may have made
sense at some point but it is wasteful now. Remove the functions that
operate on sockets and convert the callers. Not only does this make
the code smaller and more consistent but it pushes the locking burden
up to the caller which can be more intelligent about the locks. Also,
perform the same conversion (socket to sock) on the SELinux/NetLabel
glue code where it make sense.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we create idev before addresses are added, it no longer makes
sense to remove them when addresses are all deleted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we check for permission before deleting entries from SAD and
SPD, (see security_xfrm_policy_delete() security_xfrm_state_delete())
However we are not checking for authorization when flushing the SPD and
the SAD completely. It was perhaps missed in the original security hooks
patch.
This patch adds a security check when flushing entries from the SAD and
SPD. It runs the entire database and checks each entry for a denial.
If the process attempting the flush is unable to remove all of the
entries a denial is logged the the flush function returns an error
without removing anything.
This is particularly useful when a process may need to create or delete
its own xfrm entries used for things like labeled networking but that
same process should not be able to delete other entries or flush the
entire database.
Signed-off-by: Joy Latten<latten@austin.ibm.com>
Signed-off-by: Eric Paris <eparis@parisplace.org>
Signed-off-by: James Morris <jmorris@namei.org>
cbq and atm destroy their filters twice when destroying inner classes
during qdisc destruction.
Reported-and-tested-by: Strobl Anton <a.strobl@aws-it.at>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the link state from userspace not affecting any other
flags. Two duplicate notification are being sent, once as action
in the NETDEV_UP/NETDEV_DOWN notification chain and a second time
when comparing old and new device flags after the change has been
completed. Although harmless, the duplicates should be avoided.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts changesets:
6aaf47fa48b7b5f487abde34ed91c4fc038410b4
There are still some correctness issues recently
discovered which do not have a known fix that doesn't
involve doing a full hash table scan on port bind.
So revert for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
A recv() on an AF_UNIX, SOCK_STREAM socket can race with a
send()+close() on the peer, causing recv() to return zero, even though
the sent data should be received.
This happens if the send() and the close() is performed between
skb_dequeue() and checking sk->sk_shutdown in unix_stream_recvmsg():
process A skb_dequeue() returns NULL, there's no data in the socket queue
process B new data is inserted onto the queue by unix_stream_sendmsg()
process B sk->sk_shutdown is set to SHUTDOWN_MASK by unix_release_sock()
process A sk->sk_shutdown is checked, unix_release_sock() returns zero
I'm surprised nobody noticed this, it's not hard to trigger. Maybe
it's just (un)luck with the timing.
It's possible to work around this bug in userspace, by retrying the
recv() once in case of a zero return value.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from textsearch_prepare() needs to be checked
by IS_ERR(). Because it returns error code as a pointer.
Cc: "Brian J. Murrell" <netfilter@interlinx.bc.ca>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
check_compat_entry_size_and_hooks iterates over the matches and calls
compat_check_calc_match, which loads the match and calculates the
compat offsets, but unlike the non-compat version, doesn't call
->checkentry yet. On error however it calls cleanup_matches, which in
turn calls ->destroy, which can result in crashes if the destroy
function (validly) expects to only get called after the checkentry
function.
Add a compat_release_match function that only drops the module reference
on error and rename compat_check_calc_match to compat_find_calc_match to
reflect the fact that it doesn't call the checkentry function.
Reported by Jan Engelhardt <jengelh@linux01.gwdg.de>
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a helper module is unloaded all conntracks refering to it have their
helper pointer NULLed out, leading to lots of races. In most places this
can be fixed by proper use of RCU (they do already check for != NULL,
but in a racy way), additionally nf_conntrack_expect_related needs to
bail out when no helper is present.
Also remove two paranoid BUG_ONs in nf_conntrack_proto_gre that are racy
and not worth fixing.
Signed-off-by: Patrick McHarrdy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifindex == 0 does not exist and implies we should do a lookup by name if
one was given.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC doesn't like the way Stephen initially did it:
net/ipv4/tcp_probe.c:83: warning: empty declaration
Signed-off-by: David S. Miller <davem@davemloft.net>
LIMIT_NETDEBUG allows the admin to disable some warning messages (echo 0
>/proc/sys/net/core/warnings).
The "TCP: Treason uncloaked!" message can use this facility.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously inet devices were only constructed when addresses are added
(or rarely in ipmr). Therefore the default config values they get are
the ones at the time of these operations.
Now that we're creating inet devices earlier, this changes the
behaviour of default config values in an incompatible way (see bug
#8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously once inetdev_init has been called on a device any changes
made to ipv4_devconf_dflt would have no effect on that device's
configuration.
This creates a problem since we have moved the point where
inetdev_init is called from when an address is added to where the
device is registered.
This patch is the first half of a set that tries to mimic the old
behaviour while still calling inetdev_init.
It propagates any changes to ipv4_devconf_dflt to those devices that
have not had the corresponding attribute set.
The next patch will forcibly set all values at the point where
inetdev_init was previously called.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array. This allows easier manipulation which will be
needed later on to provide better management of default config values.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I made the inetdev_init call work on all devices I incorrectly
left in the panic call as well. It is obviously undesirable to
panic on an allocation failure for a normal network device. This
patch moves the panic call under the loopback if clause.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A time_wait socket inherits sk_bound_dev_if from the original socket,
but it is not used when sending ACK packets using ip_send_reply.
Fix by passing the oif to ip_send_reply in struct ip_reply_arg and
use it for output routing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when icmp_errors_use_inbound_ifaddr is set and an ICMP error is
sent after the packet passed through ip_output(), an address from the
outgoing interface is chosen as ICMP source address since skb->dev doesn't
point to the incoming interface anymore.
Fix this by doing an interface lookup on rt->dst.iif and using that device.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This isn't a bug just yet as only TCP uses sk_setup_caps for GSO.
However, if and when UDP or something else starts using it this is
likely to cause a problem if we forget to add software emulation
for it at the same time.
The problem is that right now we translate GSO emulation to the
bitmask NETIF_F_GSO_MASK, which includes every protocol, even
ones that we cannot emulate.
This patch makes it provide only the ones that we can emulate.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code used to ignore GSO completely, passing either way too
small or zero pkts_acked when GSO skb or part of it got ACKed.
In addition, there is no need to calculate the value in the loop
but simple arithmetics after the loop is sufficient. There is
no need to handle SYN case specially because congestion control
modules are not yet initialized when FLAG_SYN_ACKED is set.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent gcc versions emit warnings when unsigned variables are
compared < 0 or >= 0.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
round_jiffies for net dev watchdog timer.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This diff changes the default port range used for outgoing connections,
from "use 32768-61000 in most cases, but use N-4999 on small boxes
(where N is a multiple of 1024, depending on just *how* small the box
is)" to just "use 32768-61000 in all cases".
I don't believe there are any drawbacks to this change, and it keeps
outgoing connection ports farther away from the mess of
IANA-registered ports.
Signed-off-by: Mark Glines <mark@glines.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon an excellent bug report and initial patch by
Frederik Deweerdt.
The UNIX datagram connect code blindly dereferences other->sk_socket
via the call down to the security_unix_may_send() function.
Without locking 'other' that pointer can go NULL via unix_release_sock()
which does sock_orphan() which also marks the socket SOCK_DEAD.
So we have to lock both 'sk' and 'other' yet avoid all kinds of
potential deadlocks (connect to self is OK for datagram sockets and it
is possible for two datagram sockets to perform a simultaneous connect
to each other). So what we do is have a "double lock" function similar
to how we handle this situation in other areas of the kernel. We take
the lock of the socket pointer with the smallest address first in
order to avoid ABBA style deadlocks.
Once we have them both locked, we check to see if SOCK_DEAD is set
for 'other' and if so, drop everything and retry the lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_state_*() locking macros imply that there is some
rwlock kind of thing going on, but the implementation is
actually a spinlock which makes the code more confusing than
it needs to be.
So use plain unix_state_lock and unix_state_unlock.
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface for network device VLAN extension was confusing.
The kill_vid function is only really useful for devices that do
hardware filtering. Devices that only do VLAN receiption without
filtering were being forced to provide the hook, and there were
bugs in those devices.
Many drivers had kill_vid routine that called vlan_group_set_device, with
NULL, but that is done already.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Peroidic STP timers don't have to be exact. The hold timer runs at
1HZ, and the hello timer normally runs at 2HZ; save power by aligning
it them to next second.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge cleanup timer is fired 10 times a second for timers that
are at least 15 seconds ahead in time and that are not critical to be
cleaned asap.
This patch calculates the next time to run the timer as the minimum of
all timers or a minimum based on the current state.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function in tcp_probe is printf like, use GCC to check the args.
Sighed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just a fix to correct the number of printl arguments. Now, srtt is
logging correctly.
Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_out_of_resources() and tcp_close() perform the
same checking of number of orphan sockets. Move this
code into common place.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_fib.c: In function ‘fib6_add_rt2node’:
net/ipv6/ip6_fib.c:661: warning: label ‘out’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
in4_pton converts a textual representation of an ip4 address
into an integer representation. However, when the textual representation
is of in the form ip:port, e.g. 192.168.1.1:5060, and 'delim' is set to
-1, the function bails out with an error when reading the colon.
It makes sense to allow the colon as a delimiting character without
explicitly having to set it through the 'delim' variable as there can be
no ambiguity in the point where the ip address is completely parsed. This
function is indeed called from nf_conntrack_sip.c in this way to parse
textual ip:port combinations which fails due to the reason stated above.
Signed-off-by: Jerome Borsboom <j.borsboom@erasmusmc.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to handle ::/0 routes specially any longer.
This should fix BUG #8349.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Yuji Sekiya <sekiya@wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing NULL check and trims a line longer than 80 columns.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Joe Jezak <josejx@gentoo.org>
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix error message:
Unable to network device. --> Unable to allocate network device.
Cc: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_open should always set the carrier status since we may have set
it to off before.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forget to free all the fragments when defraging them into one packet.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs have strict checking between associate and reassociate. In
a case when an AP is restarted during a connection, it denies the
mac80211 reassoc request since this is a new association for the AP.
To fix this problem, we need to check the status code against
WLAN_STATUS_REASSOC_NO_ASSOC and clear ifsta->prev_bssid_set in
handling the association failure response.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
sys_setsockopt() do not check properly timeout values for
SO_RCVTIMEO/SO_SNDTIMEO, for example it's possible to set negative timeout
values. POSIX do not defines behaviour for sys_setsockopt in case negative
timeouts, but requires that setsockopt() shall fail with -EDOM if the send and
receive timeout values are too big to fit into the timeout fields in the socket
structure.
In current implementation negative timeout can lead to error messages like
"schedule_timeout: wrong timeout value".
Proposed patch:
- checks tv_usec and returns -EDOM if it is wrong
- do not allows to set negative timeout values (sets 0 instead) and outputs
ratelimited information message about such attempts.
Signed-off-By: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
They're the same.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing process of T.120 address in OpenLogicalChannelAck signal.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the implementation of H.323, it's not necessary to check
the addresses in Information signals.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update get_h225_addr() to meet the changes in ASN.1 types. It was using
field ip6 to access IPv6 TransportAddress, it should be ip according the
ASN.1 definition.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add support for decoding IPv6 address. I know it was manually added in
the header file, but not in the template file. That wouldn't work.
2. Add missing support for decoding T.120 address in OLCA.
3. Remove unnecessary decoding of Information signal.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet size is changed by the FTP NAT helper, the connection
tracking helper adjusts the sequence number of the newline character
by the size difference. This is wrong because NAT sequence number
adjustment happens after helpers are called, so the unadjusted number
is compared to the already adjusted one.
Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to locate the oldest entry in the history of newline character
sequence numbers, the sequence number of the current entry is incorrectly
compared with the index of the oldest sequence number instead of the number
itself.
Additionally it is not made sure that the current sequence number really
is after the oldest known one.
Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event cache time must be an absolute value, when no event exists
it is incorrectly set to 1s instead of 1s in the future.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you replace route via ip r r command the netlink multicast message is
not send. This patch corrects it. NL message is sent with NLM_F_REPLACE
flag.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8320
Signed-off-by: Milan Kocian <milon@wq.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch that changed the return value of qdisc_restart
incorrectly made the case where dequeue returns empty continue
processing packets.
This patch is based on diagnosis and fix by Patrick McHardy.
Reported-and-debugged-by: Anant Nitya <kernel@prachanda.info>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2CAP configuration parameter handling was missing the support
for rejecting unknown options. The capability to reject unknown
options is mandatory since the Bluetooth 1.2 specification. This
patch implements its and also simplifies the parameter parsing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove some unused variables and function arguments related to the
recently removed wireless extensions over rtnetlink.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_setlink doesn't allow to change subsets of the flags, just to override
the set entirely by a new one. This means that for simply setting a device
up or down userspace first needs to query the current flags, change it and
send the changed flags back, which is racy and needlessly complicated.
Mask the flags using ifi_change since this is what it is intended for.
For backwards compatibility treat ifi_change == 0 as ~0 (even though it
seems quite unlikely that anyone has been using this so far).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
