When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=51X+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc2
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This reverts commit 428aac8a81.
This isn't quite ready for 3.12, we need some more EHCI driver changes
that are just now showing up. So revert this for now, and queue it up
later for 3.13.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local symbols used in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This patch removes the ehci statictics information output in ehci_stop()
because they do not provide interesting info. At any case, the current
statistics can be viewed by reading the 'registers' file in debugfs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes ehci_vdbg debugging statements from EHCI host controller
driver because they produce too much information, lowering the signal to noise
ratio when debugging, and because they are not used anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=siJK
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-27-15-07' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Fix build breakage and new warnings.
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.
Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When debug is not enabled and dev_dbg() will expand to nothing,
log might be flooded with "callbacks suppressed". If it was not
done on purpose, better to use dev_dbg_ratelimited() instead.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Wrong capability bit was checked for best effort service latency.
bit 20 indicate port is BESL LPM capable (BLC),
bit 19 is hardware LPM capable (HLC)
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Cc: stable@vger.kernel.org
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad "xhci: Add
reset on resume quirk for asrock p67 host".
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Commit 9a11899c5e (USB: OHCI: add missing PCI PM callbacks to
ohci-pci.c) added missing ohci_suspend and ohci_resume callback
pointers, but forgot that these callbacks are declared and defined
only when CONFIG_PM is enabled.
This patch adds a preprocessor conditional to avoid build errors when
PM is disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Meelis Roos <mroos@linux.ee>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.
Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org> # 2.6.33+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c1117afb85 (USB: OHCI: make ohci-pci a separate driver)
neglected to preserve the entries for the pci_suspend and pci_resume
driver callbacks. As a result, OHCI controllers don't work properly
during suspend and after hibernation.
This patch adds the missing callbacks to the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use devm_get_clk() for automatic put upon device release, check for and
propagate errors when enabling clocks, must prepare clocks before they
can get enabled, unprepare after disable
need to use the _parent_ of the platform device for clock lookup, since
this one is associated with the respective device tree node; this change
remains neutral as long as a "globally" provided "usb%d_clk" item gets
provided by either the PPC_CLOCK implementation or clkdev_register'ed
aliases, using the correct devide and thus referencing the right DT node
becomes essential when clock lookup will become based on device tree
when common clock support will get introduced
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0/wL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-2013-08-15-step-1' into for-usb-next
xhci: Step 1 to fix usb-linus and usb-next.
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
Resolved conflicts:
drivers/usb/core/hub.c
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=n45I
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Platform updates, 64-bit DMA, and trace events for 3.12.
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device. It does not want the xHCI generic driver to
register an interrupt for it at all. The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.
Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi(). This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.
Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.
This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c814 "USB: xhci:
correctly enable interrupts".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Yu Y Wang <yu.y.wang@intel.com>
Tested-by: Yu Y Wang <yu.y.wang@intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
commit 9841f37a1c ("usb: ehci: Add support for SINGLE_STEP_SET_FEATURE
test of EHSET") added additional code to the EHCI hub driver but it is
anticipated to only have a limited audience (e.g. embedded silicon
vendors and integrators). Avoid subjecting all EHCI (and in the future
maybe xHCI/OHCI, etc.) HCD users to code bloat by conditionally
compiling the EHSET-specific additions with a new Kconfig option,
CONFIG_USB_HCD_TEST_MODE.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function dma_set_mask() tests internally whether the dma_mask pointer
for the device is initialized and fails if the dma_mask pointer is NULL.
On pci platforms, the device dma_mask pointer is initialized, when pci
devices are enumerated, to point to the pci_dev->dma_mask which is 0xffffffff.
However, for non-pci platforms, the dma_mask pointer may not be initialized
and in that case dma_set_mask() will fail.
This patch initializes the dma_mask and the coherent_dma_mask to 32bits
in xhci_plat_probe(), before the call to usb_create_hcd() that sets the
"uses_dma" flag for the usb bus and the call to usb_add_hcd() that creates
coherent dma pools for the usb hcd.
Moreover, a call to dma_set_mask() does not set the device coherent_dma_mask.
Since the xhci-hcd driver calls dma_alloc_coherent() and dma_pool_alloc()
to allocate consistent DMA memory blocks, the coherent DMA address mask
has to be set explicitly.
This patch sets the coherent_dma_mask to 64bits in xhci_gen_setup() when
the xHC is capable for 64-bit DMA addressing.
If dma_set_mask() succeeds, for a given bitmask, it is guaranteed that
the given bitmask is also supported for consistent DMA mappings.
Other changes introduced in this patch are:
- The return value of dma_set_mask() is checked to ensure that the required
dma bitmask conforms with the host system's addressing capabilities.
- The dma_mask setup code for the non-primary hcd was removed since both
primary and non-primary hcd refer to the same generic device whose
dma_mask and coherent_dma_mask are already set during the setup of
the primary hcd.
- The code for reading the HCCPARAMS register to find out the addressing
capabilities of xHC was removed since its value is already cached in
xhci->hccparams.
- hcd->self.controller was replaced with the dev variable since it is
already available.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_ring_expansion
and belongs to the event class xhci_log_msg, and adds tracepoints that trace
the debug messages associated with the expansion of endpoint ring when there
is not enough space allocated to hold all pending TRBs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_init
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug statements in the functions used to start and stop the
xhci-hcd driver.
Also, it removes an unnecessary cast of variable val to unsigned int
in xhci_mem_init(), since val is already declared as unsigned int.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_cancel_urb
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug messages related to the removal of a cancelled URB from
the endpoint's transfer ring.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch creates a new event class, called xhci_log_event,
and defines the xhci_cmd_completion trace event used for
tracing the commands issued to xHC that generate a completion
event in the event ring.
This info can be used, later, to print, in a human readable
way, the completion status and flags as well as the command's
type and fields using the trace-cmd tool and the appropriate
plugin.
Also, a tracepoint is added in handle_cmd_completion().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new event class, called xhci_log_ctx,
that records in the ring buffer the context data, the
context type (input or output), the context dma and virtual
addresses, the context endpoint entries, the slot ID and
whether the xHC uses 64 byte context data structures.
This information can be used, later, to parse and display
the context data fields with the appropriate plugin using
the trace-cmd tool.
Also, this patch defines a trace event, called xhci_address_ctx,
to trace the contexts related to the Address Device command and
adds the associated tracepoints in xhci_address_device().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_reset_ep
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with resetting an endpoint after
the reception of a STALL packet.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_quirks
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with xHCs' quirks.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_context_change
and belongs in the event class xhci_log_msg, and adds tracepoints for tracing
the debug messages related to context updates performed with Configure Endpoint
and Evaluate Context commands.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch declares an event class for trace events that
trace messages with variadic arguments, called xhci_log_msg,
and defines a trace event for tracing the debug messages in
xhci_address_device() function, called xhci_dbg_address.
In order to implement this type of trace events, a wrapper function,
called xhci_dbg_trace(), was created that records the format string
and variadic arguments into a va_format structure which is passed as
argument to the tracepoints of the class xhci_log_msg.
All the xhci_dbg() calls in xhci_address_device() are replaced
with calls to xhci_dbg_trace(). The functionality of xhci_dbg()
log messages was not removed though, but it is placed inside
xhci_dbg_trace().
This trace event aims to give the ability to the user or the
developper to isolate and trace the debug messages generated
when an Address Device Command is issued to xHC.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CONFIG_USB_XHCI_HCD_DEBUGGING option is used to enable
verbose debugging output for the xHCI host controller
driver.
In the current version of the xhci-hcd driver, this
option must be turned on, in order for the debugging
log messages to be displayed, and users may need to
recompile the linux kernel to obtain debugging
information that will help them track down problems.
This patch removes the above debug option to enable
debugging log messages at all times.
The aim of this is to rely on the debugfs and the
dynamic debugging feature for fine-grained management
of debugging messages and to not force users to set
the debug config option and compile the linux kernel
in order to have access in that information.
This patch, also, removes the XHCI_DEBUG symbol and the
functions dma_to_stream_ring(), xhci_test_radix_tree()
and xhci_event_ring_work() that are not useful anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to printk(KERN_DEBUG ...)
with either calls to xhci_dbg() or calls to pr_debug(),
depending on whether the xhci_hcd structure is available
at callsite, so that the correspoding debugging messages
are not enabled by default when CONFIG_DYNAMIC_DEBUG option
is set but rather can be enabled dynamically taking advantage
of the dynamic debugging feature.
Also, it adds a newline at the end of debugging messages in
case there is not, so that messages don't appear broken
when printed.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to xhci_info() with calls to
xhci_dbg() and removes the unused xhci_info() definition
from xhci-hcd.
By replacing the xhci_info() with xhci_dbg(), the calls to
dev_info() are replaced with calls to dev_dbg() so that
their output can be dynamically controlled via the dynamic
debugging mechanism.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Add Device Tree match table to xhci-plat.c. Add DT bindings document.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
Prevent the USB core from suspending the HWA root hub since bus_suspend
and bus_resume are not yet supported. Otherwise the PM system will chew
up CPU time constantly attempting to suspend and resume the root hub but
never succeeding.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commits 4005ad4390 (EHCI: implement new semantics for
URB_ISO_ASAP) and c75c5ab575 (ALSA: USB: adjust for changed 3.8 USB
API) became widely distributed, people have been experiencing problems
with audio transfers. The slightest underrun causes complete failure,
requiring the audio stream to be restarted.
It turns out that the current isochronous API doesn't handle underruns
in the best way. The ALSA developers would much rather have transfers
that are submitted too late be accepted and complete in the normal
fashion, rather than being refused outright.
This patch implements the requested approach. When an isochronous URB
submission is so late that all its scheduled slots have already
expired, a debugging message will be printed in the log and the URB
will be accepted as usual. Assuming it was submitted by a completion
handler (which is normally the case), it will complete shortly
thereafter with all the usb_iso_packet_descriptor status fields marked
-EXDEV.
This fixes (for ehci-hcd)
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1191603
It should be applied to all kernels that include commit 4005ad4390.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Maksim Boyko <maksboyko@yandex.ru>
CC: Clemens Ladisch <clemens@ladisch.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Embedded High-speed Host Electrical Test (EHSET) defines the
SINGLE_STEP_SET_FEATURE test as follows:
1) The host enumerates the test device with VID:0x1A0A, PID:0x0108
2) The host sends the SETUP stage of a GetDescriptor(Device)
3) The device ACKs the request
4) The host issues SOFs for 15 seconds allowing the test operator to
raise the scope trigger just above the SOF voltage level
5) The host sends the IN packet
6) The device sends data in response, triggering the scope
7) The host sends an ACK in response to the data
This patch adds additional handling to the EHCI hub driver and allows
the EHSET driver to initiate this test mode by issuing a a SetFeature
request to the root hub with a Test Selector value of 0x06. From there
it mimics ehci_urb_enqueue() but separately submits QTDs for the
SETUP and DATA/STATUS stages in order to insert a delay in between.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[jackp@codeaurora.org: imported from commit c2084930 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_USB_SUPPORT is not selected we get things like:
scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
It is much cleaner to make the various system Kconfigs select
USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config
information into USB's Kconfig, but the warnings are annoying.
Eliminate the warning by moving the definition of
USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements.
While we are at it move USB_OHCI_BIG_ENDIAN_DESC,
USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and
USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar
problems for other systems.
Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and
USB_OHCI_BIG_ENDIAN_MMIO
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch marks all xHCI controllers as no_sg_constraint
since xHCI supports building packet from discontinuous buffers.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All 4 transfer types can work well on EHCI HCD after switching to run
URB giveback in tasklet context, so mark all HCD drivers to support
it.
Also we don't need to release ehci->lock during URB giveback any more.
>From below test results on 3 machines(2 ARM and one x86), time
consumed by EHCI interrupt handler droped much without performance
loss.
1 test description
1.1 mass storage performance test:
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=200M count=1
- two usb mass storage device:
A: sandisk extreme USB 3.0 16G(used in test case 1 & case 2)
B: kingston DataTraveler G2 4GB(only used in test case 2)
1.2 uvc function test:
- run one simple capture program in the below link
http://kernel.ubuntu.com/~ming/up/capture.c
- capture format 640*480 and results in High Bandwidth mode on the
uvc device: Z-Star 0x0ac8/0x3450
- on T410(x86) laptop, also use guvcview to watch video capture/playback
1.3 about test2 and test4
- both two devices involved are tested concurrently by above test items
1.4 how to compute irq time(the time consumed by ehci_irq)
- use trace points of irq:irq_handler_entry and irq:irq_handler_exit
1.5 kernel
3.10.0-rc3-next-20130528
1.6 test machines
Pandaboard A1: ARM CortexA9 dural core
Arndale board: ARM CortexA15 dural core
T410: i5 CPU 2.67GHz quad core
2 test result
2.1 test case1: single mass storage device performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 25.280(avg:145,max:772) | 25.540(avg:14, max:75)
Arndale board: 29.700(avg:33, max:129) | 29.700(avg:10, max:50)
T410: 34.430(avg:17, max:154*)| 34.660(avg:12, max:155)
---------------------------------------------------------------------
2.2 test case2: two mass storage devices' performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 15.840/15.580(avg:158,max:1216) | 16.500/16.160(avg:15,max:139)
Arndale board: 17.370/16.220(avg:33 max:234) | 17.480/16.200(avg:11, max:91)
T410: 21.180/19.820(avg:18 max:160) | 21.220/19.880(avg:11, max:149)
---------------------------------------------------------------------
2.3 test case3: one uvc streaming test
- uvc device works well(on x86, luvcview can be used too and has
same result with uvc capture)
--------------------------------------------------------------------
upstream | patched
irq time(us) | irq time(us)
--------------------------------------------------------------------
Pandaboard A1: (avg:445, max:873) | (avg:33, max:44)
Arndale board: (avg:316, max:630) | (avg:20, max:27)
T410: (avg:39, max:107) | (avg:10, max:65)
---------------------------------------------------------------------
2.4 test case4: one uvc streaming plus one mass storage device test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 20.340(avg:259,max:1704)| 20.390(avg:24, max:101)
Arndale board: 23.460(avg:124,max:726) | 23.370(avg:15, max:52)
T410: 28.520(avg:27, max:169) | 28.630(avg:13, max:160)
---------------------------------------------------------------------
2.5 test case5: read single mass storage device with small transfer
- run below command 10 times and compute the average speed
dd if=/dev/sdN iflag=direct of=/dev/null bs=4K count=4000
1), test device A:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 6.5(avg:21, max:64) | 6.5(avg:10, max:24)
Arndale board: 8.13(avg:12, max:23) | 8.06(avg:7, max:17)
T410: 6.66(avg:13, max:131) | 6.84(avg:11, max:149)
---------------------------------------------------------------------
2), test device B:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 5.5(avg:21,max:43) | 5.49(avg:10, max:24)
Arndale board: 5.9(avg:12, max:22) | 5.9(avg:7, max:17)
T410: 5.48(avg:13, max:155) | 5.48(avg:7, max:140)
---------------------------------------------------------------------
* On T410, sometimes read ehci status register in ehci_irq takes more
than 100us, and the problem has been reported on the link:
http://marc.info/?t=137065867300001&r=1&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
