Can only happen under these conditions: 1) The DSDT version is 1,
meaning integers are 32-bits. 2) The field is between 33 and 64
bits long.
It applies cleanly back to ACPICA 20100806+ (Linux v2.6.37+).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 2.6.37+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reset the IRQ_NOAUTOEN and IRQ_NOREQUEST flags that are enabled by
default on ARM. If IRQ_NOAUTOEN is set, __setup_irq doesn't call
irq_startup, that is responsible for calling irq_unmask at startup time.
As a result event channels remain masked.
The clear is already made in bind_evtchn_to_irq with commit a8636c0 but was
missing on all others bind_*_to_irq. Move the clear in xen_irq_info_common_init.
On x86, IRQ_NOAUTOEN and IRQ_NOREQUEST are cleared by default, so this commit
doesn't impact this architecture.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Enabling SWIOTLB_XEN on ARM results in build errors because the
underlying SWIOTLB is only available on X86:
drivers/xen/swiotlb-xen.c: In function 'is_xen_swiotlb_buffer':
drivers/xen/swiotlb-xen.c:105:2: error: implicit declaration of function 'mfn_to_local_pfn
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
During review of git commit cb9c6f15f3
("xen/spinlock: Check against default value of -1 for IRQ line.")
Stefano pointed out a bug in the patch. Unfortunatly due to vacation
timing the fix was not applied and this patch fixes it up.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As it will point to some data, but not event channel data (the
shared_info has an array limited to 32).
This means that for PVHVM guests with more than 32 VCPUs without
the usage of VCPUOP_register_info any interrupts to VCPUs
larger than 32 would have gone unnoticed during early bootup.
That is OK, as during early bootup, in smp_init we end up calling
the hotplug mechanism (xen_hvm_cpu_notify) which makes the
VCPUOP_register_vcpu_info call for all VCPUs and we can receive
interrupts on VCPUs 33 and further.
This is just a cleanup.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
After build_free_nids() searches free nid candidates from nat pages and
current journal blocks, it checks all the candidates if they are allocated
so that the nat cache has its nid with an allocated block address.
In this procedure, previously we used
list_for_each_entry_safe(fnid, next_fnid, &nm_i->free_nid_list, list).
But, this is not covered by free_nid_list_lock, resulting in null pointer bug.
This patch moves this checking routine inside add_free_nid() in order not to use
the spin_lock.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When nm_i->fcnt > 2 * MAX_FREE_NIDS, stop scanning other NAT entries.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fix handling the return value of add_free_nid()]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch does two cleanups:
1. remove unused variable "fcnt" in build_free_nids().
2. make scan_nat_page() as void type and remove useless variable "fcnt".
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Directly drop the free_nid cache when nm_i->fcnt > 2 * MAX_FREE_NIDS
Since there is NOT nmi->free_nid_list_lock spinlock protection between
a sequential calling of alloc_nid() and alloc_nid_failed(), some other
threads may already add new free_nid to the free_nid_list during this
period.
We need to make sure nmi->fcnt is never > 2 * MAX_FREE_NIDS.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When recovering a journal file with fsync data for files that have
been deleted, don't bail out on recovery.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When unable to roll forward the journal, we shouldn't bail out and
not mount, we should continue to attempt the mount. Bad recovery data
is likely unrecoverable at this point, and requiring the user to try
to mount again doesn't solve any issues.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
o Deadlock case #1
Thread 1:
- writeback_sb_inodes
- do_writepages
- f2fs_write_data_pages
- write_cache_pages
- f2fs_write_data_page
- f2fs_balance_fs
- wait mutex_lock(gc_mutex)
Thread 2:
- f2fs_balance_fs
- mutex_lock(gc_mutex)
- f2fs_gc
- f2fs_iget
- wait iget_locked(inode->i_lock)
Thread 3:
- do_unlinkat
- iput
- lock(inode->i_lock)
- evict
- inode_wait_for_writeback
o Deadlock case #2
Thread 1:
- __writeback_single_inode
: set I_SYNC
- do_writepages
- f2fs_write_data_page
- f2fs_balance_fs
- f2fs_gc
- iput
- evict
- inode_wait_for_writeback(I_SYNC)
In order to avoid this, even though iput is called with the zero-reference
count, we need to stop the eviction procedure if the inode is on writeback.
So this patch links f2fs_drop_inode which checks the I_SYNC flag.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Changes for pure microMIPS cores to dynamically determine the ASID
size at boot time.
Includes bug fix https://patchwork.linux-mips.org/patch/5230/
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Original patch by Ralf Baechle and removed by Harold Koerfgen
with commit f67e4ffc79905482c3b9b8c8dd65197bac7eb508. This
allows for more generic kernels since the size of the ASID
and corresponding masks can be determined at run-time. This
patch is also required for the new Aptiv cores and has been
tested on Malta and Malta Aptiv platforms.
[ralf@linux-mips.org: Added relevant part of fix
https://patchwork.linux-mips.org/patch/5213/]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove 'arch/mips/include/asm/mips-boards/prom.h' and get rid of
all inclusions of it by Malta and SEAD-3 platforms.
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
ar7 powertv build"].
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
unbreak powertv build"].
[ralf@linux-mips.org: Test. Build. Your. Fscking. Code. Or...]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add parsing of the environment and command line variables passed to
the kernel to the firmware library.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add declaration of 'mips_scroll_message' and 'mips_display_message'
to the common generic header file for the MIPS Technologies Inc.
development boards.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Setting the LED_CORE_SUSPENDRESUME flag causes the LED driver core to call
led_classdev_suspend/led_classdev_resume during suspend/resume. Since this is
exactly what the driver's custom suspend/resume callbacks do we can replace them
by setting the LED_CORE_SUSPENDRESUME flag.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Emulation of xcr0 writes zero guest_xcr0_loaded variable so that
subsequent VM-entry reloads CPU's xcr0 with guests xcr0 value.
However, this is incorrect because guest_xcr0_loaded variable is
read to decide whether to reload hosts xcr0.
In case the vcpu thread is scheduled out after the guest_xcr0_loaded = 0
assignment, and scheduler decides to preload FPU:
switch_to
{
__switch_to
__math_state_restore
restore_fpu_checking
fpu_restore_checking
if (use_xsave())
fpu_xrstor_checking
xrstor64 with CPU's xcr0 == guests xcr0
Fix by properly restoring hosts xcr0 during emulation of xcr0 writes.
Analyzed-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The bitops prototype use an 'int' as the bit index type but the asm
implementation assume it to be a 'long'. Since the compiler does not
guarantee zeroing the upper 32-bits in a register when used as 'int',
change the bitops implementation accordingly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ESR.WnR bit is always set on data cache maintenance faults even though
the page is not required to have write permission. If a translation
fault (page not yet mapped) happens for read-only user address range,
Linux incorrectly assumes a permission fault. This patch adds the check
of the ESR.CM bit during the page fault handling to ignore the 'write'
flag.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Tim Northover <Tim.Northover@arm.com>
Cc: stable@vger.kernel.org
Commit 90556ca1 ("arm64: vexpress: Add dts files for the ARMv8 RTSM
models") added foundation-v8.dts, but erroneously set
/cpus/#address-cells = <1> while providing two cells in each cpus/cpu@N
node's reg property.
As of commit ea393a2e ("arm64: smp: honour #address-size when parsing
CPU reg property") we read in as many address cells as specified rather
than always reading two. This means that for foundation-v8.dts, we only
read the first reg cell (zero) for each cpu node, and receive a lot of
warnings at boot of the form "/cpus/cpu@1: duplicate cpu reg properties
in the DT".
This patch corrects foundation-v8.dts to have the correct value for
/cpus/#address-cells.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the arm_pm_poweroff definition expected by the
vexpress-poweroff.c driver and enables the latter for arm64.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
* arm64-prep-gic:
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
This is a revised patch based on Mengdong Lin's fix patch, which is a
supplement to a previous patch [1611a9c9: ALSA: hda - Add fixup for
Haswell to enable all pin and convertor widgets].
Some Haswell BIOS will disable the 2nd and 3rd pin/covertor widgets
when the HD-A controller changes state from D3 to D0. So when the
controller resumes after a system or runtime suspend, these widgets
are disabled and programming these widgets to D0 will cause H/W error
and codec will not respond.
In addition, we found out that some BIOS disables the pins at S3
although it shows up at boot. This confuses the driver utterly, and
the hardware falls into the fatal communication error like the above.
So in this patch, we apply intel_haswell_enable_all_pins() not only as
a fixup to a certain device (with 8086:2010) but to all Haswell
machines. The codec driver basically assumes that all pins are
exposed, so it's anyway better to see them from the beginning. Even
if all pins and converters are shown by this call, there should be no
regression in practice: the pin default configurations are still kept,
thus the disabled pins are handled as disabled by the driver
properly.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The helper function didn't include a leading space, so it was jammed
against the previous text in the audit record.
Signed-off-by: Eric Paris <eparis@redhat.com>
Merge more incoming from Andrew Morton:
- Various fixes which were stalled or which I picked up recently
- A large rotorooting of the AIO code. Allegedly to improve
performance but I don't really have good performance numbers (I might
have lost the email) and I can't raise Kent today. I held this out
of 3.9 and we could give it another cycle if it's all too late/scary.
I ended up taking only the first two thirds of the AIO rotorooting. I
left the percpu parts and the batch completion for later. - Linus
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (33 commits)
aio: don't include aio.h in sched.h
aio: kill ki_retry
aio: kill ki_key
aio: give shared kioctx fields their own cachelines
aio: kill struct aio_ring_info
aio: kill batch allocation
aio: change reqs_active to include unreaped completions
aio: use cancellation list lazily
aio: use flush_dcache_page()
aio: make aio_read_evt() more efficient, convert to hrtimers
wait: add wait_event_hrtimeout()
aio: refcounting cleanup
aio: make aio_put_req() lockless
aio: do fget() after aio_get_req()
aio: dprintk() -> pr_debug()
aio: move private stuff out of aio.h
aio: add kiocb_cancel()
aio: kill return value of aio_complete()
char: add aio_{read,write} to /dev/{null,zero}
aio: remove retry-based AIO
...
Thanks to Zach Brown's work to rip out the retry infrastructure, we don't
need this anymore - ki_retry was only called right after the kiocb was
initialized.
This also refactors and trims some duplicated code, as well as cleaning up
the refcounting/error handling a bit.
[akpm@linux-foundation.org: use fmode_t in aio_run_iocb()]
[akpm@linux-foundation.org: fix file_start_write/file_end_write tests]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ki_key wasn't actually used for anything previously - it was always 0.
Drop it to trim struct kiocb a bit.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 6ff5e45985.
Conflicts:
kernel/audit.c
This patch was starting a kthread for all the time. Since the follow on
patches that required it didn't get finished in 3.10 time, we shouldn't
ship this change in 3.10.
Signed-off-by: Eric Paris <eparis@redhat.com>
Jiri reported a regression in auditing of open(..., O_CREAT) syscalls.
In older kernels, creating a file with open(..., O_CREAT) created
audit_name records that looked like this:
type=PATH msg=audit(1360255720.628:64): item=1 name="/abc/foo" inode=138810 dev=fd:00 mode=0100640 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255720.628:64): item=0 name="/abc/" inode=138635 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
...in recent kernels though, they look like this:
type=PATH msg=audit(1360255402.886:12574): item=2 name=(null) inode=264599 dev=fd:00 mode=0100640 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255402.886:12574): item=1 name=(null) inode=264598 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255402.886:12574): item=0 name="/abc/foo" inode=264598 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
Richard bisected to determine that the problems started with commit
bfcec708, but the log messages have changed with some later
audit-related patches.
The problem is that this audit_inode call is passing in the parent of
the dentry being opened, but audit_inode is being called with the parent
flag false. This causes later audit_inode and audit_inode_child calls to
match the wrong entry in the audit_names list.
This patch simply sets the flag to properly indicate that this inode
represents the parent. With this, the audit_names entries are back to
looking like they did before.
Cc: <stable@vger.kernel.org> # v3.7+
Reported-by: Jiri Jaburek <jjaburek@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Test By: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
audit rule additions containing "-F auid!=4294967295" were failing
with EINVAL because of a regression caused by e1760bd.
Apparently some userland audit rule sets want to know if loginuid uid
has been set and are using a test for auid != 4294967295 to determine
that.
In practice that is a horrible way to ask if a value has been set,
because it relies on subtle implementation details and will break
every time the uid implementation in the kernel changes.
So add a clean way to test if the audit loginuid has been set, and
silently convert the old idiom to the cleaner and more comprehensible
new idiom.
Cc: <stable@vger.kernel.org> # 3.7
Reported-By: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Tested-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
- Note that this file is statically linked with the rest of the host kernel (KSEG0). This is because kernel modules are
loaded into mapped space on MIPS and we want to make sure that we don't get any host kernel TLB faults while
manipulating TLBs.
- Virtual Guest TLBs are implemented as 64 entry array regardless of the number of host TLB entries.
- Shadow TLBs map Guest virtual addresses to Host physical addresses.
- TLB miss handling details:
Guest KSEG0 TLBMISS (0x40000000 – 0x60000000): Transparent to the Guest.
Guest KSEG2/3 (0x60000000 – 0x80000000) & Guest UM TLBMISS (0x00000000 – 0x40000000)
Lookup in Guest/Virtual TLB
If an entry doesn’t match
deliver appropriate TLBMISS LD/ST exception to the guest
If entry does exist in the Guest TLB and is NOT Valid
Deliver TLB invalid exception to the guest
If entry does exist in the Guest TLB and is VALID
Inject the TLB entry into the Shadow TLB
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- The Guest kernel is run in UM and privileged instructions cause a trap.
- If the instruction causing the trap is in a branch delay slot, the branch
needs to be emulated to figure out the PC @ which the guest will resume
execution.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
