A regression introduced in the last set of acl patches removed the
INHERIT_ONLY flag from aces derived from the posix acl. Fix.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->readdir passes lofft_t offsets (used as nfs cookies) to
nfs3svc_encode_entry{,_plus}, but when they pass it on to encode_entry it
becomes an 'off_t', which isn't good.
So filesystems that returned 64bit offsets would lose.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo reported it on lkml in the thread
"2.6.21-rc5: maxcpus=1 crash in cpufreq: kernel BUG at drivers/cpufreq/cpufreq.c:82!"
This check added to remove_dev is symmetric to one in add_dev and handles
callbacks for offline cpus cleanly.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
failed VM entry on VMX might still change %fs or %gs, thus make sure
that KVM always reloads the segment selectors. This is crutial on both
x86 and x86_64: x86 has __KERNEL_PDA in %fs on which things like
'current' depends and x86_64 has 0 there and needs MSR_GS_BASE to work.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel virtualization extensions do not support virtualizing real mode. So
kvm uses virtualized vm86 mode to run real mode code. Unfortunately, this
virtualized vm86 mode does not support the so called "big real" mode, where
the segment selector and base do not agree with each other according to the
real mode rules (base == selector << 4).
To work around this, kvm checks whether a selector/base pair violates the
virtualized vm86 rules, and if so, forces it into conformance. On a
transition back to protected mode, if we see that the guest did not touch
a forced segment, we restore it back to the original protected mode value.
This pile of hacks breaks down if the gdt has changed in real mode, as it
can cause a segment selector to point to a system descriptor instead of a
normal data segment. In fact, this happens with the Windows bootloader
and the qemu acpi bios, where a protected mode memcpy routine issues an
innocent 'pop %es' and traps on an attempt to load a system descriptor.
"Fix" by checking if the to-be-restored selector points at a system segment,
and if so, coercing it into a normal data segment. The long term solution,
of course, is to abandon vm86 mode and use emulation for big real mode.
Signed-off-by: Avi Kivity <avi@qumranet.com>
After freeing a block there should be no reference to this block.
Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Olaf Hering pointed out that SAA7146_CLIPPING_MEM would become
very large for PAGE_SIZE > 4K.
In fact, the number of clipping windows is limited to 16,
and calculate_clipping_registers_rect() does not use more
than 256 bytes. SAA7146_CLIPPING_MEM adjusted accordingly.
Thanks-to: Olaf Hering <olaf@aepfle.de>
Acked-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix several instances of dvb-core functions using mutex_lock_interruptible
and returning -ERESTARTSYS where the calling function will either never
retry or never check the return value.
These cause a race condition with dvb_dmxdev_filter_free and
dvb_dvr_release, both of which are filesystem release functions whose
return value is ignored and will never be retried. When this happens it
becomes impossible to open dvr0 again (-EBUSY) since it has not been
released properly.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the radio drivers need video_dev, but they were depending on
VIDEO_DEV!=n. That meant that one could try to compile the driver into
the kernel when VIDEO_DEV=m, which will not work. If video_dev is a
module, then the radio drivers must be modules too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Compiling 2.6.21-rc5 with gcc-4.2.0 20070317 (prerelease)
for sparc64 fails as follows:
gcc -Wp,-MD,arch/sparc64/kernel/.time.o.d -nostdinc -isystem /home/mikpe/pkgs/linux-sparc64/gcc-4.2.0/lib/gcc/sparc64-unknown-linux-gnu/4.2.0/include -D__KERNEL__ -Iinclude -include include/linux/autoconf.h -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Os -m64 -pipe -mno-fpu -mcpu=ultrasparc -mcmodel=medlow -ffixed-g4 -ffixed-g5 -fcall-used-g7 -Wno-sign-compare -Wa,--undeclared-regs -fomit-frame-pointer -fno-stack-protector -Wdeclaration-after-statement -Wno-pointer-sign -Werror -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(time)" -D"KBUILD_MODNAME=KBUILD_STR(time)" -c -o arch/sparc64/kernel/time.o arch/sparc64/kernel/time.c
cc1: warnings being treated as errors
arch/sparc64/kernel/time.c: In function 'kick_start_clock':
arch/sparc64/kernel/time.c:559: warning: overflow in implicit constant conversion
make[1]: *** [arch/sparc64/kernel/time.o] Error 1
make: *** [arch/sparc64/kernel] Error 2
gcc gets unhappy when the MSTK_SET macro's u8 __val variable
is updated with &= ~0xff (MSTK_YEAR_MASK). Making the constant
unsigned fixes the problem.
[ I fixed up the sparc32 side as well -DaveM ]
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocfs2 wants to implement it's own splice write actor so that it can better
manage cluster / page locks. This lets us re-use the rest of splice write
while only providing our own code where it's actually important.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Splice does not need to readpage to bring the page uptodate before writing
to it, because prepare_write will take care of that for us.
Splice is also wrong to SetPageUptodate before the page is actually uptodate.
This results in the old uninitialised memory leak. This gets fixed as a
matter of course when removing the readpage logic.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Stealing pages with splice is problematic because we cannot just insert
an uptodate page into the pagecache and hope the filesystem can take care
of it later.
We also cannot just ClearPageUptodate, then hope prepare_write does not
write anything into the page, because I don't think prepare_write gives
that guarantee.
Remove support for SPLICE_F_MOVE for now. If we really want to bring it
back, we might be able to do so with a the new filesystem buffered write
aops APIs I'm working on. If we really don't want to bring it back, then
we should decide that sooner rather than later, and remove the flag and
all the stealing infrastructure before anybody starts using it.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Booting 2.6.21-rc3-g45592145 I noticed the following on one of my
machines in the bootlog:
io scheduler noop registered<6>Time: jiffies clocksource has been installed.
io scheduler deadline registered (default)
Looking at block/elevator.c, it appears that elv_register() uses two
consecutive printks in a non-atomic way, leading to the above glitch. The
attached trivial patch fixes this issue, by using a single printk.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There is a small problem in handling page bounce.
At the moment blk_max_pfn equals max_pfn, which is in fact not maximum
possible _number_ of a page frame, but the _amount_ of page frames. For
example for the 32bit x86 node with 4Gb RAM, max_pfn = 0x100000, but not
0xFFFF.
request_queue structure has a member q->bounce_pfn and queue needs bounce
pages for the pages _above_ this limit. This routine is handled by
blk_queue_bounce(), where the following check is produced:
if (q->bounce_pfn >= blk_max_pfn)
return;
Assume, that a driver has set q->bounce_pfn to 0xFFFF, but blk_max_pfn
equals 0x10000. In such situation the check above fails and for each bio
we always fall down for iterating over pages tied to the bio.
I want to notice, that for quite a big range of device drivers (ide, md,
...) such problem doesn't happen because they use BLK_BOUNCE_ANY for
bounce_pfn. BLK_BOUNCE_ANY is defined as blk_max_pfn << PAGE_SHIFT, and
then the check above doesn't fail. But for other drivers, which obtain
reuired value from drivers, it fails. For example sata_nv uses
ATA_DMA_MASK or dev->dma_mask.
I propose to use (max_pfn - 1) for blk_max_pfn. And the same for
blk_max_low_pfn. The patch also cleanses some checks related with
bounce_pfn.
Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The determination of whether the DAC has inverted cursor logic is
broken, import the version checks the X.org driver uses to fix this.
Next, when we change the timing generator, borrow code from X.org that
does 10 NOP reads of the timing generator register afterwards to make
sure the video-enable transition occurs cleanly.
Finally, use macros for the DAC registers and fields in order to
provide documentation for the next person who reads this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b19cbe2a16 [BRIDGE]: Fix fdb RCU
race
breaks sparc SMP build because atomic_add_unless is not exported.
This patch exports atomic_add_unless and atomic_cmpxchg.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dlm_migrate_lockres(), we check upfront whether the lockres is a
candidate for migration. This patch encapsulates that code in a separate
function so that dlm_empty_lockres() can also use it during umount. This
patch addresses the umount process spinning problem.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
During umount, the umount thread migrates the lockres' and the dlm_thread
frees the empty lockres'. Due to a race, the reference counting on the
lockres goes awry leading to extra puts.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The SCSI midlayer may abort a command that was already sent. If the
initiator is still trying to send the command (or data-out PDUs for
that command), the QP may time out after the midlayer times
out. Therefore, when aborting the command, iSER may still have
references for the command's buffers. When sending these PDUs, the
sends will complete with an error and their resources will be released
then.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the worthless net/sched/Makefile entry for the non-existent
source file sch_hpfq.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c20e20ab ("IB/mthca: Merge MR and FMR space on 64-bit systems")
swapped the number of MTTs and MPTs when initializing the MR table. As
a result, we get a kernel oops when the number of MTT segments
allocated exceeds 0x20000.
Noted by Troy Benjegerdes <troy@scl.ameslab.gov>, and reproduced by
Dotan Barak <dotanb@mellanox.co.il>. This fixes
https://bugs.openfabrics.org/show_bug.cgi?id=490
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This was spotted by the Coverity checker (CID 1554).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: Fix ap_poll_requests counter in lost requests error path.
[S390] zcrypt: Fix possible dead lock in AP bus module.
[S390] cio: Device status validity.
[S390] kprobes: Align probe address.
[S390] Fix TCP/UDP pseudo header checksum computation.
[S390] dasd: Work around gcc bug.
This patch implements set_mac_address for the sungem driver. This
allows changing the mac address of the interface, even when the
interface is up.
Signed-off-by: Ruben Vandeginste <snowbender@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix usb-serial/ftdi build warning
USB: fix usb-serial/generic build warning
USB: another entry for the quirk list
USB: remove duplicated device id in airprime driver
USB: omap_udc: workaround dma_free_coherent() bogosity
UHCI: Fix problem caused by lack of terminating QH
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix warning message in PCIE port driver
PCI: Stop unhiding the SMBus on Toshiba laptops
PCI: Fix up PCI power management doc
pci: set pci=bfsort for PowerEdge R900
Change prototypes for __chk_user_ptr and __chk_io_ptr to take const
void* instead of void*, so that code can pass "const void *" to them.
(Right now sparse does not warn about passing const void* to void*
functions, but that is a separate bug that I believe Josh is working on,
and once sparse does check this, the changed prototypes will be
necessary.)
Signed-off-by: Russ Cox <rsc@swtch.com>
Signed-off-by: Josh Triplett <josh@freedesktop.org>
Acked-by: Christopher Li <sparse@chrisli.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul E. McKenney writes:
> Those of use who dive into networking only occasionally would much
> appreciate this. ;-)
No problem here...
Acked-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> (but trivial)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to omap_udc, noted with some recent testing:
- Cope with some SMP-induced braindamage in ARM's dma_{alloc,free}_coherent()
implementation: alloc() can be called with IRQs blocked, but since late
last year that's no longer true for free(). This resolves really NASTY
problems with logspamming via WARN_ON(), indicating N-page leaks.
- Be more correct in handling GET_STATUS request for RECIP_ENDPOINT ... the
previous code only handled RECIP_INTERFACE, this version should be correct
except for (sigh) bulk/interrupt endpoints.
- Provide a better name for the function reporting whether the board has
vbus sensing wired up.
GET_STATUS requests for endpoint status still acts strangely though, at least
given one flakey host doesn't always ack the first DATA packet, then the packet
that gets retransmitted doesn't have data!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: use correct IDE error recovery
pdc202xx_new: Enable ATAPI DMA
ide: cosmetic adaption of drivers/ide/Kconfig concerning SATA
ide: fix locking for manual DMA enable/disable ("hdparm -d")
ide: revert "ide: fix drive side 80c cable check, take 2" for now
PCIE error output should conform to vendor_id:device_id.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.
This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the documentation of PCI power management functions.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch automatically enables pci=bfsort for the Dell PowerEdge
R900. This is necessary to ensure the onboard NICs enumerate in the
proper order, similar to the other systems already on the list.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* d_alloc() in sock_attach_fd() fails leaving ->f_dentry of new file NULL
* bail out to out_fd label, doing fput()/__fput() on new file
* but __fput() assumes valid ->f_dentry and dereferences it
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sysfs support of clockevents does not obey the "only one
value per file" rule.
The real fix is not 2.6.21 material. Therefor remove the sysfs support
for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
