Add arch/avr32/mach-*/include to include search path and copy all the
files from include/asm/arch there. The old files will be removed once
ARM does the same change and all common drivers are converted.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* git://git.infradead.org/mtd-2.6: (57 commits)
[MTD] [NAND] subpage read feature as a way to increase performance.
CPUFREQ: S3C24XX NAND driver frequency scaling support.
[MTD][NAND] au1550nd: remove unused variable
[MTD] jedec_probe: Fix SST 16-bit chip detection
[MTD][MTDPART] Fix a division by zero bug
[MTD][MTDPART] Cleanup and document the erase region handling
[MTD][MTDPART] Handle most checkpatch findings
[MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition
[MTD] physmap: resume already suspended chips on failure to suspend
[MTD] physmap: Fix suspend/resume/shutdown bugs.
[MTD] [NOR] Fix -ETIMEO errors in CFI driver
[MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
[JFFS2] Use .unlocked_ioctl
[MTD] Fix const assignment in the MTD command line partitioning driver
[MTD] [NOR] gen_probe: No debug message when debugging is disabled
[MTD] [NAND] remove __PPC__ hardcoded address from DiskOnChip drivers
[MTD] [MAPS] Remove the bast-flash driver.
[MTD] [NAND] fsl_elbc_nand: ecclayout cleanups
[MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
...
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- free pages, printed by show_free_areas()
- pages in slabs, printed by show_free_areas()
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch allows the avr32_comparator interrupt to be shared.
This is necessary as the avr32 oprofile driver shares the irq group 0
with the timer.
To make OProfile actually work on AVR32, a small patch for oprofiled is
also needed (posted to the oprofile mailing list).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
[haavard.skinnemoen@atmel.com: set IRQF_SHARED unconditionally]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds platform data to the AC97C platform device. This will
let the board add a GPIO line which is connected to the external codecs
reset line.
The platform data, ac97c_platform_data, must also contain the DMA
controller ID, RX channel ID and TX channel ID.
Tested with Wolfson WM9712 and AP7000.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does a few small cleanups around the atmel mci platform code
and in the atmel-mci driver. The platform changes simply removes an
unused variable, uses the fact that by the end we always have some form
of platform data and notes that GPIO_PIN_NONE != 0. This last point
could cause the incorrect attempt to twice reserve pin PA0.
While we've got the hood up, add linux/err.h to the atmel-mci.c include
list. It needs it and generally pulls it by voodoo but I did once
stumble across a config which don't build.
This is against Linus' latest git.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)
Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)
The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.
We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This makes the intc show up in sysfs (probably not very useful), and
allows us to easily add suspend/resume support later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SDRAM controller needs a clock in order to respond to our
commands, and suspend doesn't work very well without the SDRAM in
self-refresh mode.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use a quicklist to allocate process PGDs. This is expected to be
slightly faster since we need to copy entries from swapper_pg_dir,
which can stay around for pages on the PGD quick list.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Expand the per-process PGDs so that they cover the kernel virtual
memory area as well. This simplifies the TLB miss handler fastpath
since it doesn't have to check for kernel addresses anymore.
If a TLB miss happens on a kernel address and a second-level page
table can't be found, we check swapper_pg_dir and copy the PGD entry
into the user PGD if it can be found there.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Instead of storing physical addresses along with page flags in the
PGD, store virtual addresses and use NULL to indicate a not present
second-level page table. A non-page-aligned page table indicates a bad
PMD.
This simplifies the TLB miss handler since it no longer has to check
the Present bit and no longer has to convert the PGD entry from
physical to virtual address. Instead, it has to check for a NULL
entry, which is slightly cheaper than either.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This and the following patches aim to optimize the code dealing with
page tables and TLB operations. Each patch reduces the time it takes
to gzip a 16 MB file slightly, but I expect things like fork() and
mmap() will improve somewhat more.
This patch deals with the low-level TLB operations:
* Remove unused _TLBEHI_I define
* Use gcc builtins instead of inline assembly
* Remove a few unnecessary pipeline flushes and nops
* Introduce NR_TLB_ENTRIES define and use it instead of hardcoding it
to 32 a few places throughout the code.
* Use sysreg bitops instead of hardcoded shifts and masks
* Make a few needlessly global functions static
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Basic I2C initialization for the NGW100 board:
- Provide empty i2c device table. Daughtercards may add devices,
and the ATtiny24 could do stuff too.
- Set up EXTINT(3) so the ATtiny24 can interrupt the AP7000.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.
The function for adding the PSIF platform device is also added to the
board header file.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
