Example memory map (from HP sx1000 with VGA enabled):
0x00000 - 0x9FFFF supports only WB (cacheable) access
0xA0000 - 0xBFFFF supports only UC (uncacheable) access
0xC0000 - 0xFFFFF supports only WB (cacheable) access
pci_read_rom() indirectly uses ioremap(0xC0000) to read the shadow VGA option
ROM. ioremap() used to default to a 16MB or 64MB UC kernel identity mapping,
which would cause an MCA when reading 0xC0000 since only WB is supported there.
X uses reads the option ROM to initialize devices. A smaller test case is:
# echo 1 > /sys/bus/pci/devices/0000:aa:03.0/rom
# cp /sys/bus/pci/devices/0000:aa:03.0/rom x
To avoid this, we can use the same ioremap_page_range() strategy that most
architectures use for all ioremaps. These page table mappings come out of the
vmalloc area. On ia64, these are in region 5 (0xA... addresses) and typically
use 16KB or 64KB mappings instead of 16MB or 64MB mappings. The smaller
mappings give more flexibility to use the correct attributes.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
No functional change, just use the same names as i386.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Skip clock calibration if cpu being brought online is exactly the same
speed, stepping, etc., as the previous cpu. This significantly reduces
the time to boot very large systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64 expects following vm layout:
== low memory
[register-stack grows up]
[memory-stack grows down]
== high memory
But the code assigns the base of the register stack at the
maximum stack size offset from the fixed address where the
stack *might* start. Stack randomization will result in the
memory stack starting at a lower address than this, and if the
user has set a low stack limit with "ulimit -s", then you can
end up with the register stack above the memory stack (or if
you were very unlucky right on top of it!).
Fix: Calculate the base address for the register stack starting
from the actual address of the memory stack.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.
irq = create_irq();
if (irq < 0)
return irq;
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
So I think the right solution is to simply make pci_enable_device just
flip enable bits and move the rest of the work someplace else.
However a thorough cleanup is a little extreme for this point in the
release cycle, so I think a quick hack that makes the code not stomp the
irq when msi irq's are enabled should be the first fix. Then we can
later make the code not change the irqs at all.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: IA64: fix %ll build warnings
ACPI: IA64: fix allnoconfig build
ACPI: Only use IPI on known broken machines (AMD, Dothan/BaniasPentium M)
ACPI: ibm-acpi: allow module to load when acpi notifiers can't be set (v2)
ACPI: parse 2nd MADT by default
ACPICA: revert "acpi_serialize" changes
sony-laptop: MAINTAINERS fix entry, add L: and W:
ACPI: resolve HP nx6125 S3 immediate wakeup regression
ACPI: Add support to parse 2nd MADT
In sn_io_slot_fixup(), the parent is re-set from the bus to
io(port|mem)_resource because the address is changed in a way that it's not
child of the bus any more.
However, only the root is set but not the parent/child/sibling relationship in
the resource tree which causes 'cat /proc/iomem' to stop after this memory
area. Depding on the poition in the tree the iomem may be nearly completely
empty.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When booting an SN system without specifing a console
(i.e., no "console=" on boot line), the system will hang during
boot at the point where /sbin/init is run.
The problem is that vga_console_iobase is not converted to a
virtual address before storing in io_space[0].mmio_base.
The conversion was happening in sn_scan_pcdp(), but not in
setup_vga_console().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clearly should be checking for "val == DIE_INIT_SLAVE_ENTER".
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If a system consists of mixed processor types, kmalloc()
can be called before the per-cpu data page is initialized.
If the slab contains sufficient memory, then kmalloc() works
ok. However, if the slabs are empty, slab calls the memory
allocator. This requires per-cpu data (NODE_DATA()) & the
cpu dies.
Also noted by Russ Anderson who had a very similar patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have seen bad_pte_print when testing crashdump on an SN machine in
recent 2.6.20 kernel. There are tons of bad pte print (pfn < max_low_pfn)
reports when the crash kernel boots up, all those reported bad pages
are inside initmem range; That is because if the crash kernel code and
data happens to be at the beginning of the 1st node. build_node_maps in
discontig.c will bypass reserved regions with filter_rsvd_memory. Since
min_low_pfn is calculated in build_node_map, so in this case, min_low_pfn
will be greater than kernel code and data.
Because pages inside initmem are freed and reused later, we saw
pfn_valid check fail on those pages.
I think this theoretically happen on a normal kernel. When I check
min_low_pfn and max_low_pfn calculation in contig.c and discontig.c.
I found more issues than this.
1. min_low_pfn and max_low_pfn calculation is inconsistent between
contig.c and discontig.c,
min_low_pfn is calculated as the first page number of boot memmap in
contig.c (Why? Though this may work at the most of the time, I don't
think it is the right logic). It is calculated as the lowest physical
memory page number bypass reserved regions in discontig.c.
max_low_pfn is calculated include reserved regions in contig.c. It is
calculated exclude reserved regions in discontig.c.
2. If kernel code and data region is happen to be at the begin or the
end of physical memory, when min_low_pfn and max_low_pfn calculation is
bypassed kernel code and data, pages in initmem will report bad.
3. initrd is also in reserved regions, if it is at the begin or at the
end of physical memory, kernel will refuse to reuse the memory. Because
the virt_addr_valid check in free_initrd_mem.
So it is better to fix and clean up those issues.
Calculate min_low_pfn and max_low_pfn in a consistent way.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The evils of Kconfig's select bite us once again...
ia64/Kconfig selects ACPI, which depends on PM.
But select ignores dependencies, allnoconfig
chooses CONFIG_PM=n, and thus the menu of sub-options
under ACPI vanish, which breaks the build.
Manually select PM along with ACPI for now.
Some day, we should delete them both, or fix select.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In sn_io_slot_fixup(), the parent is re-set from the bus to
io(port|mem)_resource because the address is changed in a way that it's not
child of the bus any more.
However, only the root is set but not the parent/child/sibling relationship
in the resource tree which causes 'cat /proc/iomem' to stop after this
memory area. Depding on the poition in the tree the iomem may be nearly
completely empty.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: John Keller <jpk@sgi.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring defconfig, tiger_defconfig and zx1_defconfig up to date. Also
sprinkle KEXEC and KDUMP combinations around liberally so that my
usual regression test builds will see all combinations:
tiger_defconfig gets KEXEC=y, CRASH_DUMP=n
zx1_defconfig gets KEXEC=n, CRASH_DUMP=y
defconfig gets KEXEC=y, CRASH_DUMP=y
others remain at KEXEC=n, CRASH_DUMP=n
Signed-off-by: Tony Luck <tomy.luck@intel.com>
kdump_find_rsvd_region() is only called by
reserve_memory() which is in __init, so it seems that
kdump_find_rsvd_region() should also be in there.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ptrace misses clearing the syscall trace flag.
The increased syscall overhead is retained after the trace is finished.
This case happens when strace is terminated by force.
Signed-off-by: Akiyama, Nobuyuki <akiyama.nobuyuk@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Grammatical fixes (s/freezed/frozen/)
Make some variables static
Change a C++ "//" comment to "/* ... */"
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Similar to memory error recovery, when a cache error is consumed
by a user process terminate the user instead of crashing the system.
Signed-off-by: Russ Anderson (rja@sgi.com)
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner noticed that duplicate TLB DTC entries do not cause a
linux panic. See discussion:
http://www.gelato.unsw.edu.au/archives/linux-ia64/0307/6108.html
The current TLB recovery code is recovering from the duplicate itr.d
dropins, masking the underlying problem. This change modifies
the MCA recovery code to look for the TLB check signature of the
duplicate TLB entry and panic in that case.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
On 1.6GHz Montectio Tiger4, the following performance data is measured with
kernel built with defconfig which has NUMA configured:
Fastest sys_getcpu: 502 itc counts.
Fastest fsys_getcpu: 28 itc counts.
fsys_getcpu performance is largly impacted by whether data (node_to_cpu_map
etc) is in cache. It can take fsys_getcpu up to ~150 itc counts in cold
cache case.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
efi_initialize_iomem_resources() is declared in both include/linux/efi.h
and arch/ia64/kernel/setup.c. This patch removes the latter.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Berhhard Walle noted that on his HP rx8640 he ended up with saved_max_pfn
smaller than the highest address of system ram in /proc/iomem and proposed
a patch to base the address on the unrounded and unfiltered EFI memory
map address. Simon Horman and Magnus Damm suggested that the whole test
be moved earlier in the function. This is the combination of both of
these patches.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes boot failure because irq_desc->mask() is NULL.
- Added mask/unmask functions to ia64's irq desc function table.
- rename hw_interrupt_type to irq_chip. hw_interrupt_type is old name.
- Tony: Added same change to arch/ia64/sn/kernel/irq.c as pointed out
by Eric Biederman ... mask/unmask functions there can be no-op.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The address where the ELF core header is stored is passed to the secondary
kernel as a kernel command line option. The memory area for this header is
also marked as a separate EFI memory descriptor on ia64.
The separate EFI memory descriptor is at the moment of the type
EFI_UNUSABLE_MEMORY. With such a type the secondary kernel skips over the
entire memory granule (config option, 16M or 64M) when detecting memory.
If we are lucky we will just lose some memory, but if we happen to have
data in the same granule (such as an initramfs image), then this data will
never get mapped and the kernel bombs out when trying to access it.
So this is an attempt to fix this by changing the EFI memory descriptor
type into EFI_LOADER_DATA. This type is the same type used for the kernel
data and for initramfs. In the secondary kernel we then handle the ELF
core header data the same way as we handle the initramfs image.
This patch contains the kernel changes to make this happen. Pretty
straightforward, we reserve the area in reserve_memory(). The address for
the area comes from the kernel command line and the size comes from the
specialized EFI parsing function vmcore_find_descriptor_size().
The kexec-tools-testing code for this can be found here:
http://lists.osdl.org/pipermail/fastboot/2007-February/005983.html
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Perfmon associates vmalloc()ed memory with a file descriptor, and installs
a vma mapping that memory. Unfortunately, the vm_file field is not filled
in, so processes with mappings to that memory do not prevent the file from
being closed and the memory freed. This results in use-after-free bugs and
multiple freeing of pages, etc.
I saw this bug on an Altix on SLES9. Haven't reproduced upstream but it
looks like the same issue is there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add VERIFY_WRITE check in the beginning like compat_sys_getdents() (EINVAL vs
EFAULT).
Signed-off-by: Alexandr Andreev <aandreev@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Always build ia64 xor.o because multiple config options now depend on it.
Necessary to build .20-mm* on ia64 when, e.g., CONFIG_ASYNC_TX_DMA is
defined. Don't know if '_ASYNC_TX_DMA makes sense on ia64. If not, maybe
Kconfig should preclude it.
Could have defined a Kconfig option that defaults to true if MD_RAID456 ||
ASYNC_TX_DMA to control building of xor.o, but xor.o is only 848 bytes and
this IS ia64...
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make saved_max_pfn point to max_pfn of entire system.
Without this patch is so that vmcore is zero length on ia64. This is
because saved_max_pfn was wrongly being set to the max_pfn of the crash
kernel's address space, rather than the max_pfg on the physical memory of
the machine - the whole purpose of vmcore is to access physical memory that
is not part of the crash kernel's addresss space.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Sort-Of-Acked-By: Jay Lan <jlan@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
To provide compatibilty with SN kernels that do and do not
have ACPI IO support, the SN PROM must build different
versions of some ACPI tables based on which kernel is booting.
As such, the tables may have to change at kernel boot time.
By default, prior to kernel boot, the PROM builds an empty
DSDT (header only) and no SSDTs. If an ACPI capable kernel
boots, the kernel will notify the PROM, at platform setup time,
and the PROM will build full DSDT and SSDT tables.
With the latest changes to acpi_table_init(), the table lengths
are saved, and when our PROM changes them, the changes are not seen,
and the kernel will crash on boot. Because of issues with kexec support,
we are not able to create the tables prior to acpi_table_init().
As a result, we are making a second call to acpi_table_init() to
process the rebuilt DSDT and SSDTs.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SN code to initialize the Hub/TIO infrastructure needs to
execute before bus scanning. This was previously done with
an early call to acpi_bus_register_driver(). But now that
ACPI is using the Linux driver model, a driver cannot be registered
that early. Make changes to have the init routines invoked via
calls to acpi_get_devices().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Fix "spin_lock_irqrestore" to "spin_unlock_irqrestore."
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
acpi_boot_init() is making a bad check on the return
status from acpi_table_parse(). acpi_table_parse() now
returns zero on success, one on failure.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If an ATA drive uses legacy mode, ata driver will choose 14 and 15
as the fixed irq number. On ia64 platform, such numbers are GSI and
should be converted to irq vector.
Below patch against kernel 2.6.20 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This convters the sysctl ctl_tables to use C99 initializers. While I was
looking at it I discovered it was using a portion of the sysctl binary
addresses space under CTL_KERN KERN_OSTYPE which was completely inappropriate.
So I completely removed all of the sysctl binary names, to remove and avoid
the ABI conflict.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By not using the enumeration in sysctl.h (or even understanding it) the SN
platform placed their arch specific xpc directory on top of CTL_KERN and only
because they didn't have 4 entries in their xpc directory got lucky and didn't
break glibc.
This is totally irresponsible. So this patch entirely removes sys_sysctl
support from their sysctl code. Hopefully they don't have ascii name
conflicts as well.
And now that they have no ABI numbers add them to the end instead of the
sysctl list instead of the head so nothing else will be overridden.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove in-source externs, linux/init.h is included in all cases.
This is a fixups for "Dynamic kernel command-line" patch.
It also includes some uml __init fixups so that we can __initdata also its
command_line.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rename saved_command_line into boot_command_line.
2. Set command_line as __initdata.
[akpm@osdl.org: move some declarations to the right place]
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Part of long forgotten patch
http://groups.google.com/group/fa.linux.kernel/msg/e98e941ce1cf29f6?dmode=source
Since then, m32r grabbed two copies.
Leave s390 copy because of important absence of CONFIG_VT, but remove
references to non-existent timerlist_lock. ia64 also loses timerlist_lock.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>